Pioneer AVIC-5000NEX, AVIC-6000NEX, AVIC-7000NEX, AVIC-8000NEX, AVIC-X8610BS Installation Manual

Installation Manual
Manuel d’installation

MULTIMEDIA NAVIGATION RECEIVER

RECEPTEUR DE NAVIGATION MULTIMEDIA

AVIC-8000NEX
AVIC-7000NEX
AVIC-6000NEX
AVIC-5000NEX
AVIC-X8610BS

English Français

Contents

Precautions

Your new product and this manual 3
Important safeguards 3

Connection

Precautions before connecting the

system 5
Before installing this product 5
To prevent damage 6

– Notice for the blue/white lead 6
Parts supplied 7
Connecting the power cord (1) 8
Connecting the power cord (2) 10
Connecting the system 12
Connecting to separately sold power

amp 13

Connecting an iPhone with Lightning

connector 14

– Connecting via the USB port 14

– Connecting via the HDMI port 14

– Connecting via the RGB input 15

Connecting an iPhone with 30-pin

connector 15

– Connecting via the AUX input 15

– Connecting via the RGB input 16

Connecting the Android™ device 16

– Connecting an Android device with an

HDMI port 16

– Connecting an Android device with an

MHL port 17

Connecting the MirrorLink™ device 17
Securing the High Speed HDMI
Connecting a rear view camera 19
Connecting the external video

component 20

– Using AV input 20

– Using an AUX input 21

Connecting an HDMI device 22
Connecting the rear display 22

®

Cable 18

– When using a rear display connected to

rear video output 22

Installation

Precautions before installation 23
To avoid electromagnetic interference 23
Before installing 23

– For AVIC-8000NEX and AVIC-7000NEX

users 24

Installing this product 24

– Installation notes 24
– Parts supplied 25
– Installation using the screw holes on

the side of this product 25

– Fastening the detachable faceplate 26

Installing the GPS antenna 27

– Installation notes 27
– Parts supplied 27
– When installing the antenna inside the

vehicle (on the dashboard or rear
shelf) 28

Installing the microphone 29

– Parts supplied 29
– Mounting on the sun visor 29
– Installation on the steering column 30
– Adjusting the microphone angle 30

After installation
After installing this product 31

2

En

Precautions

Your new product and this
manual

! The navigation features of this product

(and the rear view camera option if pur­chased) are intended solely to aid you in
the operation of your vehicle. It is not a sub­stitute for your attentiveness, judgment
and care when driving.

! Never use this product to route to hospi-

tals, police stations, or similar facilities in
an emergency. Please call the appropriate
emergency number.

! Do not operate this product, any applica-

tions, or the rear view camera option (if pur­chased) if doing so will divert your attention
in any way from the safe operation of your
vehicle. Always observe safe driving rules
and follow all existing traffic regulations. If
you experience difficulty in operating this
product or reading the display, park your
vehicle in a safe location and apply the
parking brake before making the necessary
adjustments.

! This manual explains how to install this

product in your vehicle. Operation of this
product is explained in the separate man­uals.

! Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the
performance of any of the vehicle’s operat­ing systems of safety features, including
airbags, hazard lamp buttons, or (iii) impair
the driver’s ability to safely operate the vehi­cle. In some cases, it may not be possible
to install this product because of the vehi­cle type or the shape of the vehicle interior.

! Model icons shown in this manual indicate

that the description is intended for the
models indicated by the icons.
If the following icon is shown, the descrip­tion is applied only to the model shown.
e.g.)

8000NEX

Section

01

English

Important safeguards

WARNING

Pioneer does not recommend that you install
this product yourself. This product is de­signed for professional installation only. We
recommend that only authorized Pioneer ser­vice personnel, who have special training
and experience in mobile electronics, set up
and install this product. NEVER SERVICE
THIS PRODUCT YOURSELF. Installing or
servicing this product and its connecting
cables may expose you to the risk of electric
shock or other hazards, and can cause da­mage to this product that is not covered by
warranty.

! Read this manual fully and carefully before

installing this product.

! Keep this manual handy for future refer-

ence.

! Pay close attention to all warnings in this

manual and follow the instructions care­fully.

! This product may in certain circumstances

display inaccurate position of your vehicle,
the distance of objects shown on the
screen, and compass directions. In addi­tion, the system has certain limitations, in­cluding the inability to identify one-way
streets, temporary traffic restrictions and
potentially unsafe driving areas. Please ex­ercise your own judgment in the light of ac­tual driving conditions.

! As with any accessory in your vehicle’s in-

terior, this product should not divert your
attention from the safe operation of your
vehicle as it may result in serious injury or
death. If you experience difficulty in operat­ing the system or reading the display,
please make adjustments while safely
parked.

! Please remember to wear your seat belt at

all times while operating your vehicle. If
you are in an accident, your injuries can be
considerably more severe if your seat belt
is not properly buckled.

En

3

Section

01

Precautions

! Certain country and government laws may

prohibit or restrict the placement and use
of this product in your vehicle. Please com­ply with all applicable laws and regulations
regarding the use, installation and opera­tion of this product.

4

En

Connection

Section

02

Precautions before
connecting the system

WARNING

Do not take any steps to tamper with or dis­able the parking brake interlock system
which is in place for your protection. Tamper­ing with or disabling the parking brake inter­lock system could result in serious injury or
death.

CAUTION

! If you decide to perform the installation

yourself, and have special training and ex­perience in the mobile electronics instal­lations, please carefully follow all of the
steps in the installation manual.

! Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir­ing to remain exposed.

! Do not directly connect the yellow lead of

this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause
the insulation to fail at the point where
the wire passes from the passenger com­partment into the engine compartment. If
the yellow lead’s insulation tears as a re­sult of contact with metal parts, short-cir­cuiting can occur, resulting in
considerable danger.

! It is extremely dangerous to allow cables

to become wound around the steering col­umn or shift lever. Be sure to install this
product, its cables, and wiring away in
such so that they will not obstruct or hin­der driving.

! Make sure that the cables and wires will

not interfere with or become caught in
any of the vehicle’s moving parts, espe­cially the steering wheel, shift lever, park­ing brake, sliding seat tracks, doors, or
any of the vehicle’s controls.

! Do not route wires where they will be ex-

posed to high temperatures. If the insula­tion heats up, wires may become

damaged, resulting in a short circuit or

English

malfunction and permanent damage to
the product.

! Do not cut the GPS antenna cable to

shorten it or use an extension to make it
longer. Altering the antenna cable could
result in a short circuit or malfunction.

! Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis­tor or filter, etc.) may fail to work properly.

! Never feed power to other electronic pro-

ducts by cutting the insulation of the
power supply lead of this product and tap­ping into the lead. The current capacity of
the lead will be exceeded, causing over­heating.

Before installing this product

! Use this unit with a 12-volt battery and ne-

gative grounding only. Failure to do so may
result in a fire or malfunction.

! To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be­fore installation.

En

5

y

Section

02

Connection

To prevent damage

WARNING

! Use speakers over 50 W (output value)

and between 4 W to 8W (impedance value).
Do not use 1 W to 3W speakers for this
unit.

! The black cable is ground. When instal-

ling this unit or power amp (sold sepa­rately), make sure to connect the ground
wire first. Ensure that the ground wire is
properly connected to metal parts of the
car’s body. The ground wire of the power
amp and the one of this unit or any other
device must be connected to the car sepa­rately with different screws. If the screw
for the ground wire loosens or falls out, it
could result in fire generation of smoke or
malfunction.

Ground wire

Other devices
(Another electronic
device in the car)

*1

Not supplied for this unit.

Metal parts of car’s bod

! When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this
product.

! When disconnecting a connector, pull the

connector itself. Do not pull the lead, as
you may pull it out of the connector.

! This product cannot be installed in a vehi-

cle without ACC (accessory) position on
the ignition switch.

C

C

A

O

F

N

F

O

S

T

A

R

T

Power amp

F

F

O

O

N

S

T

A

R

T

! To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe­cially important to insulate all unused
speaker leads, which if left uncovered may
cause a short circuit.

! Attach the connectors of the same color to

the corresponding colored port, i.e., blue
connector to the blue port, black to black,
etc.

! Refer to the owner’s manual for details on

connecting the power amp and other units,
then make connections accordingly.

! Since a unique BPTL circuit is employed,

do not directly ground the * side of the
speaker lead or connect the * side of an­other side of the speaker lead together. Be
sure to connect the * side of the speaker
lead to the * side of the speaker lead on
this product.

Notice for the blue/white lead

! When the ignition switch is turned on (ACC

ON), a control signal is output through the
blue/white lead. Connect to an external
power amp’s system remote control term­inal, the auto-antenna relay control term­inal, or the antenna booster power control
terminal (max. 300 mA 12 VDC). The con­trol signal is output through the blue/white
lead, even if the audio source is switched
off.

! Be sure not to use this lead as the power

supply lead for the external power amps.
Such connection could cause excessive
current drain and malfunction.

! Be sure not to use this lead as the power

supply lead for the auto-antenna or anten­na booster. Such connection could cause
excessive current drain and malfunction.

ACC position No ACC position

6

En

Connection

Parts supplied

Parts marked (*) are supplied with AVIC­8000NEX, AVIC-7000NEX and AVIC-6000NEX.

This product Power cord

GPS antenna Microphone

Section

02

English

Mini-jack extension
cable

Lock tie*

USB cable

En

7

Section

02

Connection

Connecting the power cord (1)

Yellow

To terminal supplied with power regardless of
ignition switch position.

Red

To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

Note

When a subwoofer is connected to this product
instead of a rear speaker, change the rear output
setting in the initial setting. (Refer to Operation
Manual.) The subwoofer output of this product is
monaural.





Left Right

Rear speaker or
subwoofer (4



Ω

)



White

White/black Gray/black

Green

Green/black

With a two-speaker system, do not connect anything
to the speaker leads that are not connected to
speakers.

Gray

Violet

Violet/black









Front speakerFront speaker

Rear speaker or
subwoofer (4 Ω)

When using a subwoofer of 70 W (2 Ω), be sure to connect with violet and violet/black leads of this
product. Do not connect anything with green and green/black leads.

Green

Not used.

Green/black

8

En

Violet

Violet/black





Subwoofer (4



2

Ω

)

Connection

This product

Fuse (10 A)

14 cm (5-1/2 in.)

Yellow/black (MUTE)

If you use equipment with a mute
function, connect that equipment to
the Audio Mute lead. If not, keep the

Power supply

Power cord

Audio Mute lead free of any
connections.

Note

Audio source will be set to mute or attenuate, while
the following sounds will not be muted or
attenuated. For details, refer to Operation Manual.
—

Voice guidance of the navigation

—

Incoming ring tone and incoming voice of the
cellular phone that is connected to this product
via Bluetooth wireless technology

Section

02

English

Blue/white (SYSTEM REMOTE CONTROL)

To auto-antenna relay control terminal or antenna
booster power control terminal (max. 300 mA 12 V DC).
If the vehicle has a glass antenna, connect to the
antenna booster power control terminal (max. 300 mA
12 V DC).

En

9

Section

02

Connection

Connecting the power cord (2)

Pink (CAR SPEED SIGNAL INPUT)

This product is connected here to detect the distance the vehicle travels. Always connect the
vehicle’s speed detection circuit. Failure to make this connection will increase errors in the
vehicle’s location display.

WARNING

IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING
ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE VEHICLE´S ANTILOCK
BRAKING SYSTEM, AUTOMATIC TRANSMISSION AND SPEEDOMETER INDICATION.

CAUTION

It is strongly suggested that the speed pulse wire be connected for accuracy of navigation
and better performance.

Note

The position of the speed detection circuit and the position of the parking brake switch
vary depending on the vehicle model. For details, consult your authorized Pioneer dealer
or an installation professional.

Light green (PARKING BRAKE)

Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply
side of the parking brake switch.

If this connection is made incorrectly or omitted, certain functions of this product will be
unusable.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR IS
DESIGNED TO DETECT PARKED STATUS AND MUST
BE CONNECTED TO THE POWER SUPPLY SIDE OF THE
PARKING BRAKE SWITCH. IMPROPER CONNECTION
OR USE OF THIS LEAD MAY VIOLATE APPLICABLE
LAW AND MAY RESULT IN SERIOUS INJURY OR
DAMAGE.

Power supply side

Ground side

Parking brake switch

10

En

Connection

Section

02

English

This product

Power cord

Violet/white (REVERSE-GEAR SIGNAL INPUT)

This is connected so that this product can detect whether
the vehicle is moving forwards or backwards. Connect the
violet/white lead to the lead whose voltage changes when
the shift lever is put in reverse. Unless connected, the
sensor may not detect your vehicle traveling
forward/backward properly, and thus the position of your
vehicle detected by the sensor may be misaligned from the
actual position.

Note

When you use a rear view camera, please make
sure to connect this lead. Otherwise you cannot
switch to the rear view camera picture.

Power supply

En

11

Section

02

Connection

Connecting the system

iDatalink adapter input
Please refer to the instruction
manual for the iDatalink adapter
(sold separately).

This product

Wired remote input
Please refer to the instruction manual for
the Hard-wired remote control adapter
(sold separately).

3.55 m (11 ft. 8 in.)

Vehicle antenna

SiriusXM Connect Vehicle Tuner
Please refer to the instruction manual
for SiriusXM Connect Vehicle Tuner
(sold separately).

Antenna jack

4 m (13 ft. 1 in.)

GPS antenna

Microphone

12

WARNING

· To avoid the risk of accident and the potential violation of applicable laws, this
product should never be used while the vehicle is being driven except for
navigation purposes. And, also rear displays should not be in a location where it
is a visible distraction to the driver.

· In some countries, the viewing of images on a display inside a vehicle even by

persons other than the driver may be illegal. Where such regulations apply they
must be obeyed and this product’s video source should not be used.

En

Connection

Connecting to separately sold power amp

RCA

Rear outputs
(REAR OUTPUT)

15 cm (5-7/8 in.)

Front outputs
(FRONT OUTPUT)

This product

cables

(sold separately)

Power amp
(sold separately)

Power amp
(sold separately)

Power amp
(sold separately)

Section

02

English

White, Red (SWL, SWR)

Blue/white

To system control terminal of the power amp
(max. 300 mA 12 V DC).

System remote control





Front speaker





Notes

· You can change the RCA output of the subwoofer depending on your subwoofer
system. (Refer to Operation Manual.)

· The subwoofer output of this product is monaural.

Power supply

Power cord





Rear speaker









Subwoofer





13

En

Section

02

Connection

Connecting an iPhone with
Lightning connector

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the
manual for the cable.

! For details concerning the connection, opera-

tions and compatibility of iPhone, refer to Op­eration Manual.

Connecting via the USB port

The USB interface cable for iPod / iPhone (CD­IU52) (sold separately) is required for the con­nection.

USB port 1

USB port 2

iPhone with
Lightning connector

USB cable

1.5 m (4 ft. 11 in.)

This product

Connecting via the HDMI port

8000NEX 7000NEX

The following cables are required for the con­nection.
! HDMI interface cable for iPod / iPhone

(CD-IH202) (sold separately)

! USB interface cable for iPod / iPhone (CD-

IU52) (sold separately)

! Lightning Digital AV Adapter (Apple Inc.

products) (sold separately)

USB cable

1.5 m (4 ft. 11 in.)

High Speed HDMI
(Type A - A)
(supplied with CD-IH202)

Lightning Digital AV Adapter
(Apple Inc. products)
(sold separately)

6000NEX

USB port 1

HDMI port

iPhone with
Lightning connector

®

Cable

This product

14

USB interface cable for iPod / iPhone
(CD-IU52) (sold separately)

USB interface cable for iPod / iPhone
(CD-IU52) (sold separately)

En

Connection

Note

! When you connect the High Speed HDMI

Cable, use the lock tie to fix it securely.

= For details, refer to Securing the High

Speed HDMI

®

Cable on page 18.

Connecting via the RGB input

5000NEX X8610BS

The following cables are required for the con­nection.
! VGA/USB interface cable for iPod / iPhone

(CD-IV202AV) (sold separately)

! USB interface cable for iPod / iPhone (CD-

IU52) (sold separately)

! Lightning to VGA Adapter (Apple Inc. pro-

ducts) (sold separately)

USB port 1

This product

®

Connecting an iPhone with
30-pin connector

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the
manual for the cable.

! For details concerning the connection, opera-

tions and compatibility of iPhone, refer to Op­eration Manual.

Connecting via the AUX input

The USB interface cable for iPod / iPhone (CD­IU201V) (sold separately) is required for the
connection.

USB port 1

This product

Section

02

English

RGB input

iPhone with
Lightning connector

VGA/USB interface cable
for iPod / iPhone
(CD-IV202AV) (sold separately)

Lightning to VGA Adapter
(Apple Inc. products)
(sold separately)

USB interface cable for iPod / iPhone
(CD-IU52) (sold separately)

USB port 2

Mini-jack extension cable
2 m (6 ft. 7 in.)

USB cable

1.5 m
(4 ft. 11 in.)

USB interface cable for iPod / iPhone
(CD-IU201V) (sold separately)

AUX input

iPhone with
30-pin connector

Note

Connect the USB cable to USB port 1 when using
“aha” or “Pandora” as the source.

En

15

Section

02

Connection

Connecting via the RGB input

The USB interface cable for iPod / iPhone (CD­IU201S) (sold separately) is required for the
connection.

USB port 1

USB cable

1.5 m (4 ft. 11 in.)

This product

RGB input

iPhone with
30-pin connector

Connecting the Android

™

device

8000NEX 7000NEX

App Connectivity Kit (CD-AH200) (sold sepa­rately) is required for the connection.

Notes

! For details on how to connect an external de-

vice using a separately sold cable, refer to the
manual for the cable.

! For details concerning the connection and op-

erations of Android device, refer to Operation
Manual.

! When you connect the High Speed HDMI

Cable, use the lock tie to fix it securely.

= For details, refer to Securing the High

Speed HDMI

Connecting an Android device
with an HDMI port

6000NEX

®

Cable on page 18.

®

This product

16

USB interface cable for iPod / iPhone
(CD-IU201S) (sold separately)

En

USB port 2

USB cable
(supplied with
CD-AH200)

Adapter cable
(HDMI Type A - D)
(supplied with CD-AH200)

USB - micro USB cable
(Type USB A - micro USB B)
(supplied with CD-AH200)

HDMI port

High Speed HDMI®
Cable (Type A - A)
(supplied with
CD-AH200)

Android device

Connection

Connecting an Android device
with an MHL port

This product

Connecting the MirrorLink
device

The USB interface cable for use with Mirror-

™

Link

devices (CD-MU200) (sold separately) is

required for the connection.

This product

™

Section

02

English

USB port 2

USB cable
(supplied with
CD-AH200)

High Speed HDMI® Cable
(Type A - A)
(supplied with CD-AH200)

MHL adapter
(supplied with
CD-AH200)

USB - micro USB cable
(Type USB A - micro USB B)
(supplied with CD-AH200)

HDMI port

Android device

USB port 2

MirrorLink device

USB cable
(supplied with CD-MU200)

USB - micro USB cable
(Type USB A - micro USB B)
(supplied with CD-MU200)

Note

For details on how to connect an external device
using a separately sold cable, refer to the manual
for the cable.

En

17

Section

02

Connection

Securing the High Speed

®

HDMI

8000NEX 7000NEX

Be sure to fix the High Speed HDMI®Cable
with the lock tie, when you connect the exter­nal device with the High Speed HDMI

1 Insert the High Speed HDMI
the HDMI port.

2 Wrap the lock tie around the hook
above the HDMI port and the High Speed
HDMI
the High Speed HDMI

1 Hook
2 Lock tie
3 High Speed HDMI

p Do not tighten up the lock tie more than

Cable

6000NEX

®

®

Cable into

®

Cable, and then tighten it to secure

3

necessary.

®

2

®

Cable

Cable.

1

Cable.

18

En

Connection

Connecting a rear view camera

When this product is used with a rear view
camera, it is possible to automatically switch
from the video to rear view image when the
shift lever is moved to REVERSE (R). Camera
View mode also allows you to check what is
behind you while driving.

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR
IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.

CAUTION

! The screen image may appear reversed.
! The rear view camera is used as an aid to

keep an eye on trailers, or backing into a tight
parking spot. Do not use this function for en­tertainment purposes.

! Objects in rear view may appear closer or

more distant than in reality.

! Please note that the image area shown by the

rear view camera may differ slightly when full­screen images are displayed when backing
and when checking the rear of the vehicle
while moving forward.

Rear view camera

(ND-BC6)

(sold separately)

To video output

Brown (BC IN)

Violet/white
(REVERSE-GEAR SIGNAL
INPUT)

Section

02

English

RCA cable
(supplied with ND-BC6)

This product

Power supply
Power cord

For more details about the wiring, refer to Connecting
the power cord (2) on page 10.

Notes

! This mode is available when the rear view

camera setting is set to “On”. (For details,
refer to Operation Manual.)

! Connect this product to the rear view camera

only. Do not connect to any other
equipment.

En

19

Section

02

Connection

Connecting the external
video component

Using AV input

You can connect an external video component
or external camera to this product.

Connecting an external camera

This product

15 cm (5-7/8 in.)

Yel low
(VIDEO INPUT
OR CAMERA
INPUT)

RCA cable
(sold separately)

Connecting the video component

This product

23 cm (9 in.)

Red, white
(AUDIO INPUT)

External video
component
(sold separately)

15 cm (5-7/8 in.)

Yellow
(VIDEO INPUT
OR CAMERA
INPUT)

RCA cables
(sold separately)

To video outputTo audio outputs

To video output

External camera
(sold separately)

Note

This mode is available when the setting of AV
input is set to “Camera”. (For details, refer to Op­eration Manual.)

20

En

Note

This mode is available when the setting of AV
input is set to “Source”. (For details, refer to Op­eration Manual.)