Parkside PHS 160 A1 User Manual [el]
DETAIL SANDER PHS 160 A1
DETAIL SANDER
Operation and Safety Notes
Translation of original operation manual
ŞLEFUITOR MANUAL
Instrucţiuni de utilizare şi de siguranţă
Traducerea instrucţiunilor de utilizare originale
ΤΡΙΒΕΙΟ ΧΕΙΡΟΣ
Υποδείξεις χειρισμού και ασφαλείας
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
RUČNA BRUSILICA
Upute za posluživanje i za Vašu sigurnost
Prijevod originalnih uputa za uporabu
РЪЧНА ШЛАЙФМАШИНА
Инструкции за обслужване и безопасност
Превод на оригиналното ръководство за експлоатация
HANDSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
7
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama
uređaja.
Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.
Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции
на уреда.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες της
συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB / CY Operation and Safety Notes Page 5
HR Upute za posluživanje i za Vašu sigurnost Stranica 13
RO Instrucţiuni de utilizare şi de siguranţă Pagina 21
BG Инструкции за обслужване и безопасност страница 29
GR / CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 37
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 47
8
A B
1 2
3
4
5
6
7
C D
°
5
4
°
5
4
°
5
4
°
5
4
5
°
4
5
°
4
5
°
4
5
4
°
2
Table of contents
Introduction
Proper use ......................................................................................................................Page 6
Features .........................................................................................................................Page 6
Included items ...............................................................................................................Page 6
Technical information ....................................................................................................Page 7
General safety advice for electrical power tools
1. Workplace safety .....................................................................................................Page 7
2.
Electrical safety .........................................................................................................Page 7
3. Personal safety ..........................................................................................................Page 8
4.
Careful handling and use of electrical power tools ...............................................Page 8
Safety advice relating specifically to this device .........................................................Page 9
Preparing for use ...............................................................................................Page 9
Vacuum dust extraction ................................................................................................Page 10
Dust box for internal vacuum extraction ......................................................................Page 10
Reducer piece ...............................................................................................................Page 10
Attaching / detaching sanding sheets ..........................................................................Page 10
Rotating the backing plate ...........................................................................................Page 10
Advice on use ................................................................................................................Page 11
Maintenance and cleaning .........................................................................Page 11
Service centre .......................................................................................................Page 11
Warranty ...................................................................................................................Page 11
Disposal ......................................................................................................................Page 12
Declaration of Conformity / Manufacturer....................................Page 12
5 GB/CY
Introduction
The following pictograms are used in these operating instructions / on the device:
Read instruction manual!
W
V
Watts (Effective power)
Volt (AC)
~
Safety class II Danger of fire from flying sparks!
Observe caution and safety notes! Dust hazard!
Risk of explosion!
Keep children away from electrical
power tools!
Detail sander PHS 160 A1
Introduction
Caution – electric shock!
Danger to life!
Risk of loss of life by electric shock from
damaged mains lead or mains plug!
Wear hearing protection, dust protection
mask, protective glasses and protective
gloves.
Dispose packaging and appliance in
an environmentally-friendly way!
and could give rise to considerable dangers. We
will not accept liability for loss or damage arising
from improper use. Not suitable for commercial use.
Please make sure you familiarise yourself
fully with the way the device works before you
use it for the first time and that
you understand how to handle electrical power tools
correctly. To help you do this please read the accompanying operating instructions. Keep these instructions
in a safe place. If you pass the device on to anyone
else, please ensure that you also pass on all the
documentation.
Proper use
The device is intended for dry sanding of wood,
plastic, metal, filler and painted surfaces. The device
is particularly suitable for corners, profiles or difficult
to access places. Any other use or modification to
the device shall be considered as improper use
6 GB/CY
Features
1
Mains lead
2
Adapter port
3
Reducer piece for external vacuum extraction
4
Dust box for internal vacuum extraction
5
Release button - dust collection box
6
Ventilation slots
7
Patented backing plate (360° rotatable)
8
ON / OFF switch
Included items
1 Detail sander PHS 160 A1
1 Sanding sheet
1 Reducer piece for external vacuum extraction
1 Operating instructions
Introduction / General safety advice for electrical power tools
Technical information
Nom. power input: 160 W
Nominal voltage: 230 V~ 50 Hz
Nominal speed: n
13000 min
0
Nom. oscillation speed: n0 26000 min
Backing plate: 360° rotatable
Protection class:
Noise and vibration data:
Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 76 dB(A)
Sound power level: 90 dB(A)
Uncertainty K: 3 dB
-1
-1
General safety advice for
electrical power tools
WARNING!
and instructions! Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electricity (by means of a mains lead) and electrical tools
powered by rechargeable batteries (without a
mains lead).
Read all the safety advice
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration a
Uncertainty K = 1,5 m / s
WARNING!
= 2,309 m / s
h
2
The vibration level given in
2
these instructions has been measured in accordance
with a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different
vibration levels and in many cases they may exceed
the values given in these instructions. It is easy to
underestimate the vibration load if the electrical power tool is used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
1. Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive environments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
Keep children and other
people away while you are
operating the electrical tool.
Distractions can cause you to lose control of
the device.
2. Electrical safety
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth. Unmodified
plugs and matching sockets reduce the risk of
electric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrigerators with any part of your body.
7 GB/CY
General safety advice for electrical power tools
There is an increased risk of electric shock if
your body is earthed
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d)
device, to hang up the device or to pull
e) When working outdoors with an
f) Use a residual current device (RCD)
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
electrical power tool always use extension cables that are also approved
for use outdoors. The use of an extension
cable suitable for outdoor use reduces the risk
of electric shock.
for protection if operating the electrical power tool in a moist environment
is unavoidable. The use of an RCD reduces
the risk of electric shock.
.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
that they are properly connected and
correctly used. The use of these devices
reduces the hazard presented by dust.
check
4. Careful handling and use
of electrical power tools
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo
of carelessness when using the device can lead
to serious injury.
b)
personal protective equipment such as dust
c) Avoid unintentional operation of the
8 GB/CY
Wear personal protective
equipment and always wear
safety glasses. The wearing of
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of electrical power tool used and work undertaken,
reduces the risk of injury.
device. Check that the electrical power
tool is switched off before you connect
it to the mains, pick it up or carry it.
ment
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are undertaking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug from the socket
before you make any adjustments to
the device, change accessories or when
the device is put away. This precaution is
intended to prevent you from unintentionally
starting the device.
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
General safety advice for electrical power tools / Preparing for use
and advice. Electrical power tools are dan-
gerous when they are used by inexperienced
people.
e) Look after the device carefully. Check
that moving parts are working properly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have damaged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this particular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those intended can lead to dangerous situations.
Safety advice relating
specifically to this device
Securely support the workpiece. Use clamps or
a vice to grip the workpiece firmly. This is much
safer than holding it in your hand.
Never support yourself by placing your hands
near or in front of the device or the workpiece
surface. A slip can result in injury.
If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
Always work with the mains lead leading
away from the rear of the device.
make sure that nobody is placed in any danger
Any harmful / noxious dusts generated from
DANGER OF FIRE FROM FLYING
SPARKS! Abrading metal creates
flying sparks. For this reason, always
and that there are no inflammable materials
near the working area.
WARNING!
sanding represent a risk to the health of the
person operating the device and to anyone
near the work area.
NOXIOUS FUMES!
that give rise to dusts that are hazardous to
health, the sander must be connected to a suitable external dust extraction device.
Ensure that there is adequate ventilation when
working on plastic, paint, varnish etc.
Do not soak the materials or the surface you
are about to work on with liquids containing
solvents.
Do not abrade moistened materials or damp
surfaces.
Avoid sanding paints containing lead or other
substances hazardous to health.
Do not work on materials containing asbestos.
Asbestos is a known carcinogen.
Avoid contact with the moving sanding sheet.
Operate the device only with an attached
sanding sheet.
Never use the device for a purpose for which it
was not intended nor with non-original parts /
accessories. The use of tools or accessories
other than those recommended in the operating
instructions could lead to you suffering an injury.
Switch the device off and allow it to come to a
standstill before you put it down.
Always keep the device clean, dry and free of
oil or grease.
Preparing for use
CAUTION! Make sure that the device is switc
off before you connect it to the mains supply.
Note! Always switch on the delta sander before
bringing it into contact with the workpiece material.
Switching on the device:
Move the ON / OFF switch
into the “ON” position.
Switching off the device:
Move the ON / OFF switch
the “OFF” position.
WARNING!
ARD! When sanding wood and in
particular when working on materials
DUST HAZ-
Wear protective glasses and a dust
mask!
8
downwards
8
upwards into
hed
9 GB/CY
Preparing for use
Vacuum dust extraction
WARNING!
DANGER OF FIRE! There is
the danger of fire when working with electrical
devices that have a dust box or can be connected
to a vacuum cleaner. Under certain conditions the
wood dust in the dust extraction bag (or in the
vacuum‘s dust bag) may ignite, e.g. as a result of
flying sparks generated when abrading metals or
metal objects left in wood. This can happen particularly if the wood dust is mixed with paint residue
or other chemicals and the abraded particles are
hot from prolonged abrasion. Therefore you must
empty the device’s dust collection box and the
vacuum cleaner’s dust bag before taking a break
or stopping work and always avoid overheating of
the abraded particles and the device.
Wear a dust mask!
WARNING!
Always pull the mains plug is
out of the socket before doing any work on the
device.
Dust box for internal
vacuum extraction
Reducer piece
Connection:
Push the reducer piece
port
.
2
into the adapter
3
Push the hose of a suitable dust extraction de-
vice approved for that purpose (e.g. a workshop
vacuum cleaner) on to the reducer piece
.
3
Removal:
Pull the dust extraction device hose off the
reducer piece
Pull off the reducer piece
Attaching / detaching
.
3
.
3
sanding sheets
WARNING!
of the socket before doing any work on the device.
Attaching:
Sanding sheets are attached to the backing plate
7
by means of the hook and pile fastening.
Detaching:
Simply pull the sanding sheet off the backing
plate
Always pull the mains plug is out
(see Fig. C).
7
Connection:
Push the dust box for internal vacuum extraction
4
on to the hand-held sander until it engages.
Removal:
Press the release button
box for internal vacuum extraction
5
of the dust extraction
4
and
withdraw it towards the rear of the device.
NOTE: Always empty the dust collection box
4
in due time and shake any remaining dust out; this
will ensure optimal vacuum performance.
10 GB/CY
Rotating the backing plate
WARNING!
Always pull the mains plug is out
of the socket before doing any work on the device.
Rotate the backing plate
7
into the desired
position (see Fig. D).
Sanding and surfaces:
The sanding output and the quality of the surface
finish are determined by the grade of grit on the
sanding sheet.
Always use sanding sheets with grades that
are suitable for the particular surface you are
sanding.
Preparing for use / Maintenance and cleaning / Service centre / Warranty
Advice on use
Switch the device on before placing it against
the workpiece.
Apply light sanding pressure only.
Advance the device at an even rate.
Change sanding sheets at the appropriate time.
Do not work on different types of material using
the same sanding sheet (e.g. wood and then
metal). To achieve the best sanding results you
should use unworn, undamaged sanding sheets.
Clean the sanding sheet from time to time with
a vacuum cleaner.
Sand difficult to reach places with the front or
side corners of the backing plate
Work in parallel and overlapping widths.
After sanding the workpiece, lift the device
from the workpiece before switching it off.
7
.
have the replacement carried out by
the manufacturer or its service centre.
This will ensure that your device remains safe
to use.
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The appliance has been manufactured with care
and meticulously examined before delivery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
Maintenance and cleaning
WARNING!
Always pull the mains plug is out
of the socket before doing any work on the device.
The delta sander is maintenance-free.
Clean the device frequently. This should be done
immediately after you have finished using it.
For cleaning the housing use a dry cloth only.
Remove any adhering sanding dust with a
narrow paint brush.
Never any kind of sharp object or petrol,
solvents or cleaning agents that might attack
plastic. Do not allow any liquids to enter the
inside of the device.
Always keep the ventilation slots
Service centre
WARNING!
Have your device
6
clear.
repaired only by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
WARNING!
If the plug or mains
lead needs to be replaced, always
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile components, e.g. buttons or batteries. This product is for
private use only and is not intended for commercial
use.
The warranty is void in the case of abusive and improper handling, use of force and internal tampering not carried out by our authorized service branch.
Your statutory rights are not restricted in any way
by this warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
DES UK LTD
Tel.: 0871 5000 700 (£ 0.10 / minute)
e-mail: support.uk@kompernass.com
11 GB/CY
Warranty / Disposal / Declaration of Conformity / Manufacturer
IE
Kompernass Service Ireland
Tel: 1850 930 412 (0,082 EUR/Min.)
Standard call rates apply.
Mobile operators may vary.
e-mail: support.ie@kompernass.com
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electrical
power tools with the household
rubbish!
In accordance with European Directive 2002 / 96 / EC
(covering waste electrical and electronic equipment)
and its transposition into national legislation, worn
out electrical power tools must be collected separately
and taken for environmentally compatible recycling.
Contact your local refuse disposal authority for
more details of how to dispose of your worn out
electrical devices.
Declaration of Conformity /
Manufacturer
We, Kompernaß GmbH, the person responsible for
documents: Mr Felix Becker, Burgstr. 21, D-44867
Bochum, Germany, hereby declare that this product
complies with the following standards, normative
documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EC Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
Applicable harmonized standards
EN 60745-1:2009, EN 60745-2-4:2009,
EN 62233:2008, IEC 60745-1:2006,
IEC 60745-2-4/A1:2008, EN 55014-1:2006,
EN 55014-2/A2:2008, EN 61000-3-2:2006,
EN 61000-3-3:2008
and confirm this with the CE symbol.
Type / Machine designation:
Detail sander PHS 160 A1
12 GB/CY
Date of manufacture (DOM): 11 - 2010
Serial number: IAN 61372
Bochum, 30.11.2010
Hans Kompernaß
- Managing Director -
We reserve the right to make technical modifications
in the course of product development.
Popis sadržaja
Uvod
Pravilno korištenje uređaja ........................................................................................ Stranica 14
Oprema ...................................................................................................................... Stranica 14
Obim isporuke ............................................................................................................ Stranica 14
Tehnički podaci ..........................................................................................................Stranica 15
Opće sigurnosne upute za električni alat
1. Sigurnost na radnom mjestu .................................................................................. Stranica 15
2.
Električna sigurnost ................................................................................................ Stranica 15
3. Sigurnost osoba .....................................................................................................Stranica 16
4.
Pažljivo postupanje s električnim uređajima i njihovo korištenje ........................Stranica 16
Upute koje se odnose na sigurno rukovanje uređajem ...........................................Stranica 17
Stavljanje u pogon ......................................................................................... Stranica 17
Odsisavanje prašine ..................................................................................................Stranica 18
Kutija za prašinu za vlastito usisavanje ....................................................................Stranica 18
Redukcijski komad ......................................................................................................Stranica 18
Postavljanje / skidanje brusnog lista ......................................................................... Stranica 18
Okretanje brusne ploče .............................................................................................Stranica 18
Radne upute ............................................................................................................... Stranica 19
Održavanje i čišćenje ................................................................................... Stranica 19
Servis ......................................................................................................................... Stranica 19
Jamstveni list.......................................................................................................Stranica 19
Zbrinjavanje ........................................................................................................ Stranica 20
Objašnjenje konformnosti / Proizvođač ......................................Stranica 20
13 HR
Uvod
U ovim uputama za uporabu / na uređaju rabi se slijedeće prikaze:
Čitati upute za rukovanje!
W
V
W (Efektivna snaga)
Volt (Imjenični napon)
~
Zaštitna klasa II Opasnost od požara uslijed letećih iskri!
Obratiti pažnju na upozoravajuće
i sigurnosne upute!
Opasnost od eksplozije!
Držite djecu podalje od
električnog alata!
Ručna brusilica PHS 160 A1
Uvod
Prije prvog korištenja upoznajte se sa
svim funkcijama uređaja i informirajte se
o pravilnom rukovanju s električnim
uređajem. K tome pročitajte slijedeće upute za korištenje. Dobro čuvajte ove upute. U slučaju prodaje
uređaja proslijedite sve dokumente na treću osobu.
Čuvajte se strujnog udara!
Opasnost po život!
Opasnost po život zbog udara strujom
ako je oštećen mrežni kabel ili mrežni
utikač!
Nosite zaštitu za uši, masku za zaštitu
od prašine od prašine, zaštitne naočale
i zaštitne rukavice.
Ugrožavanje prašinom!
Materijal ambalaže i uređaj zbrinite na
način neškodljiv za okoliš!
Oprema
1
Mrežni kabel
2
Priključak za adapter
3
Redukcijski dio za ispumpavanje
4
Kutija za prašinu
5
Gumb za otpuštanje zaporke pretinca za prašinu
6
Ventilacijski otvori
7
Patentirana brusna ploča
(moguće okrenuti za 360°)
8
Prekidač za UKLJUČIVANJE / ISKLJUČIVANJE
Pravilno korištenje uređaja
Uređaj je namjenjen za suho brušenje drva, plastike,
metala, smjese za kitanje kao i lakirane površine.
Uređaj je naročito prikladan za kuteve, profile ili
teško pristupačna mjesta. Svaka druga primjena ili
promjena uređaja smatra se da nije u skladu s njegovom namjenom te postoji ozbiljna opasnost od
nesreće. Za štete nastale nepravilnim korištenjem
nećemo preuzeti nikakvu odgovornost. Ovaj alat
nije namijenjen za profesionalnu uporabu.
14 HR
Obim isporuke
1 Ručna brusilica PHS 160 A1
1 Brusni list
1 Redukcijski dio za ispumpavanje
1 Uputa za upotrebu
Tehnički podaci
Nazivna snaga: 160 W
Nazivni napon: 230 V~ 50 Hz
Nazivni broj okretaja: n
13000 min
0
Nazivni broj titranja: n0 26000 min
-1
-1
Brusna ploča: 360° zaokretljiva
Klase zaštite:
Uvod / Opće sigurnosne upute za električni alat
Opće sigurnosne upute
za električni alat
UPOZORENJE!
upute kao i sve ostale upute! U slučaju ne
pridržavanja sigurnosnih uputa kao i ostalih uputa,
prijeti opasnost od strujnog udara, požara i / ili
teških ozljeda.
Pročitajte sigurnosne
Informacija o buci i vibraciji:
Mjerna vrijednost za buku utvrđena sukladno
EN 60745. A-ocjenjena razina buke električnog
alata iznosi tipično:
Razina zvučnog tlaka: 76 dB(A)
Razina snage zvuka: 90 dB(A)
Nesigurnost K: 3 dB
Potrebno je nositi štitnike za uši!
Ocjenjeno ubrzavanje, karakteristično:
Vibracija ruke a
= 2,309 m / s
h
Nesigurnost K = 1,5 m / s
UPOZORENJE!
2
2
Razina titranja, navedena
u ovim uputama, je istražena i određena sukladno
normiranom postupku mjerenja, koji je naveden u
EN 60745 i koji je prikladan za uspoređivanje stroja.
Razina titranja je promijenljiva, ovisno o korištenju
električnog alata, te može u pojedinim slučajevima
ležati iznad vrijednosti, navedene u ovim uputama.
Razina opterećenja titranja može biti podcjenjena,
ako se električni alat redovito koristi na takav način.
Uputa: Za precizno ocjenjivanje titrajnog otperećenja tijekom određenog radnog vremena, potrebno
je također uzeti u obzir vremena kad je stroj isključen,
ili je uključen ali se zapravo ne rabi. To može znatno
smanjiti titrajno opterećenje, tijekom cijelog radnog
vremena.
Sačuvajte sve sigurnosne upute kao i sve
ostale upute za ubuduće!
U sigurnosnim uputa rabljeni izraz „električni alat“
odnosi se na električne uređaje sa mrežnim pogonom (sa mrežnim kabelom) i na električni alat sa
akumula
torskim pogonom (bez mrežnog kabela).
1. Sigurnost na radnom mjestu
a) Vodite uvijek računa o tome, da Vaše
radno mjesto bude čisto i dobro osvjetljeno. Nered i ne osvjetljeno područje
rada, može uzrokovati nezgode.
b)
Ne rabite stroj u području gdje
prijeti opasnost od eksplozije,
gdje se nalaze zapaljive teku-
ćine, plinovi ili prašine. Električni alati proiz-
vode iskre, koje mogu zapaliti prašinu ili pare.
c)
Za vrijeme uporabe elek
tričnog alata, držite djecu i druge
osobe izvan dohvata istoga.
U slučaju nepažnje, možete izgubiti kontrolu
nad strojem.
2. Električna sigurnost
a) Mrežni utikač uređaja mora odgova-
rati utičnici. Utikač se ni na kakav
način ne smije mijenjati. Ne koristite
adapterske utičnice zajedno s zaštitno
uzemljenim uređajima. Neizmijenjeni
utikači i odgovarajuće utičnice smanjuju rizik
električnog udara.
b) Izbjegavajte dodir tijela s uzemljenim
površinama kao što su cijevi, radijatori, pećnice i hladnjaci. Postoji povećana
15 HR
Opće sigurnosne upute za električni alat
opasnost od električnog udara ukoliko je vaše
tijelo uzemljeno.
c) Uređaj držite podalje od kiše i vlage.
Prodiranje vode u unutrašnjost uređaja povećava opasnost električnog udara.
d)
za izvlačenje utikača iz utičnice. Kabel
e) Kod rada na otvorenome koristite
f) Ako je korištenje električnog alata u
Ne koristite kabel u neke
druge svrhe, npr. za nošenje
uređaja, vješanje uređaja ili
držite podalje od topline, ulja, oštrih
rubova i pokretnih dijelova uređaja.
Oštećeni ili spetljani kabel ili utikač povećava
rizik električnog udara.
samo produžni kabel koji je dozvoljen
za korištenje na otvorenome. Upotreba
produžnog kabla namijenjenog za korištenje
na otvorenome smanjuje rizik električnog udara.
vlažnim prostorima neizbježno, rabite
zaštitnu strujnu sklopku. Korištenje zaštit-
ne strujne sklopke, smanjuje rizik strujnog udara.
3. Sigurnost osoba
a) Budite uvijek pozorni, vodite računa
o tome što radite i razumno pristupite
radu s električnim alatom. Ne rabite
stroj, ako ste umorni ili pod utjecajem
droga, alkohola ili lijekova. Jedan trenu
nepažnje za vrijeme korištenja stroja, može
uzrokovati teške ozljede.
b)
kao maske za prašinu, protuklizne zaštitne
c) Spriječite slučajno uključenje. Uvjerite
Nosite osobnu zaštitnu opre-
mu i uvijek zaštitne očale.
Korištenje osobne zaštitne opreme,
cipele, zaštitnu kacigu ili štitnik za uši, ovisno o
vrsti i uporabi električnog alata, smanjuje rizik
od ozljeda.
se u to, da je električni alat isključen,
prije uključenja na struju, podizanja
ili nošenja. Ako pri nošenju uređaja držite
prst na sklopki za UKLJUČENJE / ISKLJUČENJE
ili ako je uređaj uključen, prijeti opasnost od
nezgode.
tak
d) Prije uključenja stroja, uklonite alat
za podešavanje ili vijčani ključ. Alat ili
ključ, koji se nalazi u rotirajućem dijelu stroja,
može prouzročiti ozljede.
e) Izbjegavajte nenaravan polažaj tijela.
Vodite računa o tome da sigurno
stojite na tlu i održavate vlastitu ravnotežu. Na taj način bolje možete kontrolira-
ti uređaj, posebno u neočekivanim situacijama.
f) Nosite prikladnu odjeću. Ne nosite
široku odjeću ili nakit. Držite kosu,
odjeću i rukavice dalje od pomičnih
dijelova. Opuštena odjeća, nakit ili duga kosa
mogu biti zahvaćeni od pomičnih dijelova.
g) Ako se montira uređaje za usisavanje
i prihvaćanje prašine, uvjerite se u
to da su priključeni i da se pravilno
koriste. Uporaba tih uređaja, smanjuje
ugrožavanje od prašine.
4. Pažljivo postupanje s
električnim uređajima i
njihovo korištenje
a) Nemojte uređaj preopterećivati.
Koristite onaj električni uređaj koji
odgovara za Vaš rad. S odgovarajućim
električnim uređajem bolje i sigurnije ćete raditi u navedenom području rada.
b) Ne koristite električni uređaj s neisprav-
nim prekidačem. Električni uređaj koji se više
ne može uključiti i isključiti opasan je i treba
ga dati popraviti.
c) Izvucite utikač iz utičnice, prije namje-
štanja uređaja, zamjene dijelova
opreme ili odlaganja uređaja. Ova
sigurnosna mjera spriječava slučajno
pokretanje električnog alata. Ova mje-
ra opreza spriječava nenamjerno pokretanje
uređaja.
d) Čuvajte ne korišteni električni uređaj
tako da nije na dohvatu djeci. Ne
dopustite da uređaj koriste osobe
koje s njim nisu upoznate ili koje nisu
pročitale upute. Električni alati su opasni
kada ih korite osobe bez iskustva.
16 HR
Opće sigurnosne upute za električni alat / Stavljanje u pogon
e) Pažljivo održavajte uređaj. Kontroli-
rajte da li pokretni dijelovi uređaja
besprijekorno funkcioniraju i da ne
zapinju, da dijelovi nisu slomljeni ili
tako oštećeni da je funkcija uređaja
upitna. Molimo da oštećene dijelove
dadete popraviti prije korištenja uređaja. Brojne nesreće imaju uzrok zbog loše
održavanih električnih alata.
f) Rabite električni alat, opremu i ugrad-
ni alat, itd. sukladno ovim uputama i
na način kako je propisano za ovaj
posebni tip uređaja. Pri tome uzmite
u obzir radne uvjete i rad koji se izvodi.
Uporaba električnog alata za drugu osim
predviđene primjene, može uzrokovati opasne
situacije.
Upute koje se odnose na
sigurno rukovanje uređajem
Osigurajte obradak. Koristite stezne naprave /
škripac da biste pričvrstili obradak. Isti je na taj
način bolje prihvaćen nego u Vašoj ruci.
Niti u kojem slučaju ne naslanjajte ruke pored ili
ispred uređaja i plohe koju obrađujete, jer kod
proklizavanja postoji opasnost od povrede.
U slučaju opasnosti, odmah izvucite mrežni uti-
kač iz utičnice.
Vodite mrežni kabel uvijek tako da se isti nalazi
iza uređaja.
svakako pazite da time ne ugrožavate osobe i
Šetne / otrovne prašine koje nastaju uslijed
pogotovo kada obrađujete materijale koji stva-
OPASNOST OD POŽARA
USLIJED LETEĆIH ISKRI! Kada
brusite metal letjeti će iskre. Stoga
da se u blizini radnog mjesta ne nalaze zapaljivi materijali.
UPOZORENJE!
obrade predstavljaju ugrožavanje zdravlja za
korisnika uređaja ili za osobe koje se nalaze u
blizini.
UGROŽAVANJE PRAŠINOM!
Kod dužih radova pri obradi drva, a
OTROVNE PARE!
UPOZORENJE!
raju prašinu koja ugrožava zdravlje, priključite
uređaj na prikladnu eksternu odsisnu napravu.
Nosite zaštitne naočale i zaštitnu
masku koja Vas štiti od prašine!
Kod obrade plastičnog materijala, boja, lakova
itd. pobrinite se za dovoljnu cirkulaciju zraka.
Ne natapajte materijale ili plohe koje ćete
obrađivati s tekućinama koje sadrže otapala.
Ne obrađujete navlaženi materijal ili vlažne
površine.
Izbjegavajte brušenje boja koje sadrže olovo ili
druge materijale koji mogu ugrožavati zdravlje.
Ne smije se obrađivati materijal koji sadrži
azbest. Azbest se smatra kancerogenim.
Izbjegavajte kontakt s vibrirajućim brusnim listom.
Koristite uređaj samo s postavljenim brusnim listom.
Nikada ne koristite uređaj u svrhu za koju nije
predviđen i koristite ga samo s originalnim dijelovima / priborom. Uporaba drugih dijelova ili
druge opreme, nego opisanih u uputama za
korištenje, može prouzrokovati opasnost od
ozljeda.
Nakon što ste isključili uređaj, pričekajte prije
nego što ga odložite, dok se on sasvim ne
zaustavi.
Uređaj mora uvijek biti čist, suh i bez ulja ili masti.
Stavljanje u pogon
PAŽNJA! Prije nego što uređaj priključite na
struju, provjerite da je uređaj isključen.
Opaska! Uključite delta brusilicu uvijek prije kontakta s materijalom i privodite uređaj tek tada prema
obratku.
Uključivanje uređaja:
Gurnite sklopku za UKLJUČVANJE / ISKLJUČI-
8
VANJE
Isključivanje uređaja:
Gurnite sklopku za UKLJUČVANJE / ISKLJUČI-
VANJE
prema dolje, pozicija „ON“.
8
prema gore, pozicija „OFF“.
17 HR
Loading...