Omron E5ZE DATASHEET

Multipoint Temperature Controller

E5ZE

Compact, Easy-to-mount Multipoint
Temperature Controller (Casing)

Compact, Easy-to-use, Board-type
Multipoint Temperature Controller (Open)

• Easy-to-mount, user-friendly models with casing.

• 50% smaller in projection space than the previous E5ZD Multi­point Temper a ture Cont roll er.

• Connector terminal block saves wiring effort.

• High-speed input sampling.

• Heating/cooling model s are availab le.

Note: Open models do not bear CE markings.

Model Number Structure

■Model Number Lege nd

E5ZE-8@AAM@@-E

1 2 3 4 5 6 7

1. Control Point

8: 8

2. Control Method

A: Standard
V: Heating/cooling

3. Control Output

A: Option (see note 1)

4. Heater Burnout and SSR Failure Detection (see note 2)

A: Option (see note 3)

5. Communications

M: Option (see note 4)

6. Input Type

TC: Thermocouple
P: Platinum resistance thermometer

7. Casing

B: Yes
Blank:No (open type)

Note: 1. The E53-E8Q Voltage Output Unit or the E53-E8C Current

Output Unit can be used with the E5ZE. The E53-E8Q Volt­age Output Unit and the E53-E8C Current Output Unit are
sold separately.

2. The heater burnout and SSR failure detection function of the
E5ZE will be invalid if the heating side control output of the
E5ZE is current output.

3. The E54-E8CT CT Input Unit is required for the heater burn­out and SSR failure detection. The E54-E8CT CT Input Unit
is sold separately.

4. The E53-E01 Communications Unit for RS-232C communi­cation or the E53-E04 Communications Unit for RS-422 and
RS-485 communication can be used with the E5ZE. The
E53-E01 Communications Unit and the E53-E04 Communi­cations Unit are sold separately.

Multipoint Temperature Controller E5ZE 1

Ordering Information

■List of Models

No. of

control

points

8 No Standard Option Option Option E5ZE-8AAAMTC-E E5ZE-8AAAMP-E

Casing Control

method

Heating and
cooling

Yes Standard Option Option Option E5ZE-8AAAMTCB-E E5ZE-8AAAMPB-E

Heating and
cooling

Control

output

Option Option Option E5ZE-8VAAMTC-E E5ZE-8VAAMP-E

Option Option Option E5ZE-8VAAMTCB-E E5ZE-8VAAMPB-E

Heater burnout

and SSR failure

detection

Communica-

tions

Input type

Thermocouple Platinum resistance

thermometer

■I/O Units (Order Separately)

Units Models

RS-232C Communications Unit E53-E01
RS-422/485 Communications Unit E53-E04
CT Input Unit E54-E8CT
Voltage Output Unit E53-E8Q
Current Output Unit E53-E8C

■Accessories (Order Separately)

Current Transformers (CT)

Hole diameter 5.8 mm 12.0 mm
Model E54-CT1 E54-CT3

Note: The above CTs are not provided with the E5ZE.

Recommended Power Supply

S82J Switching Power Supply

Input voltage Power ratings Output voltage Output current Model

Open-frame type Covered-type

100 to 240 VAC 50 W 24 V 2.1 A S82J-05024A S82J-05024D

100 W 4.5 A S82J-10024A S82J-10024D
150 W 6.5 A S82J-15024A

S82J-15024B
S82J-15024C

S82J-15024D
S82J-15024E
S82J-15024F

S82K Switching Power Supply

Input voltage Power ratings Output voltage Output current Model

100/200 VAC 50 W 24 V 2.1 A S82K-05024

100 W 4.2 A S82K-10024

Wiring Devices

Connector Terminal Conversion Unit

Specifications Model

20-pole, M2.4 terminal block XW2B-20G4
20-pole, M3.5 terminal block XW2B-20G5

2 Multipoint Temperature Controller E5ZE

I/O Block

Specifications Model

8-point (SPST-NO x 8) relay output with NPN DC coil (+ common) G7TC-OC08
16-point (SPST-NO x 16) relay output with NPN DC coil (+ common) G7TC-OC16
16-point (SPST-NO x 16) relay output with NPN DC coil (+ common) G7VC-OC16
16-point (SPST-NO x 16) SSR AC output with NPN DC coil (+ common) G7VC-OA16
16-point (SPST-NO x 16) SSR DC output with NPN DC coil (+ common) G7VC-OD16

Connecting Cable

Specifications Model

2 m long E5ZE-CBL200

Setting Display Unit

Connecting model Connecting part Model (see note 2)

RS-232C Connector E5ZD-SDL1
RS-422 Terminal block E5ZD-SDL2-X
RS-485 Terminal block E5ZD-SDL3-X

E5ZD-SDLM

Note: 1. The Setting Display Unit is originally for use with the E5ZD . Be careful when using the Setting Display Unit with the E5ZE as some of the

E5ZE’s functions cannot be used with the Setting Display Unit.

2. Each model available as a 100-to-240-VAC type or 24-VDC type. (Exception: The E5ZD-SDLM is available only as a 24-VDC type).

Multipoint Temperature Controller E5ZE 3

Specifications

■Ratings

Supply voltage 24 VDC
Operating voltage range 85% to 110% of rated supply voltage
Power consumption 15 W + 20% max. at rated supply voltage
Input Input type Thermocouple: K, J, R, S, T, E, B, N, L, U, W, PL-II

Input impedance Thermocouple: 1 M
Rated platinum resistance

thermometer current

Control outputs Voltage output (with short-circuit protecting function)

Alarm outputs Temperature alarm:The total output of all control points (alarm 1 NPN open collector output and

No. of input c ontrol points 8 input and 8 control points
Setting method Via communication
Control method ON/OFF control

Platinum resistance thermometer: Pt100, JPt100

Ω min.

1 mA

ON: 12
OFF: 0.5 VDC max.
Max. load current: 30 mA DC per point

Current output

Rated output range: 4 to 20 mA DC
Current output range: 0 to 22 mA DC

With an output value of 0%: 4
With an output value of 100%:20

Max. load resistance: 600

Open collector output (NPN) (cooling side only)

Max. applied voltage: 30 VDC
Max. load current: 50 mA DC per point
ON residual voltage: 2 VDC max.
OFF leakage current: 1 mA DC max.

HB alarm (heater burnout detection): Total output of all control points (1-point NPN open collector

HS alarm (SSR failure detection): Total output of all control points (1-point NPN open collector

Temperature controller error output (memory, set value, or hardware error):
1-point NPN open collector output

Max. applied voltage: 30 VDC
Max. load current: 50 mA DC per point

Hybrid of 2-PID control and fuzzy control
Manual operation

± 1.2 VDC

+0

/

mA DC

–0.6

+2

/–0 mA DC

Ω per point

alarm 2 NPN open collector output)

output)

output)

4 Multipoint Temperature Controller E5ZE

■Input Ranges

Thermocouple

Input (switch

selectable)

(see note 1)

Range

Setting no. 01/82/34/9567AB
Min. setting unit 1

°C −200 to

°F −300 to

K (CA)

Chromel vs.

alumel (see

note 2)

1,300

2,300

°C or 0.1°C

J (IC)/L

Iron vs.

constantan

−100 to 850 0 to 1,700 −200 to 400 0 to 600 100 to 1,800 0 to 1,300 0 to 2,300 0 to 1,300

−100 to

1,500

R/S
Platinum
vs. Plati-

num rhod-

ium 10%

0 to 3,000 −300 to 700 0 to 1,100 300 to 3,000 0 to 2,300 32 to 4,100 0 to 2,300

T (CC)/U

Copper vs.

constantan

E (CRC)

Chromel vs.

constantan

B

Platinum

rhodium

30% vs.

platinum

rhodium 6%

N

Nichrosil

vs. nisil

W

(see note 3)

PL-II

(Platinum)

Platinum Resistance Thermometer

Input (switch

selectable)

(see note 1)

Range

Setting no. 01
Min. setting unit 1

Note: 1. The setting selector set to 0 (K) or 0 (Pt 100) before shipping.

°C −100.0 to 500.0 −100.0 to 500.0
°F −100.0 to 900.0 −100.0 to 900.0

2. A temperature range is factory-set to a range of –200

3. Thermocouple W is W/Re5-26 (tungsten rhenium 5, tungsten rhenium 26).

Pt 100 JPt 100

°C or 0.1°C

° to 1,300°C (K(CA)) or −100.0° to 500.0°C (Pt 100).

Multipoint Temperature Controller E5ZE 5

■Characteristics

Measurement accuracy (see note) Thermocouple:

±0.3% of the process value or ±2°C, whichever greater) ±1 digit max.

(
(

±0.3% of the process value or ±3.6°F, whichever greater) ±1 digit max.

Platinum resistance thermometer:

(

±0.3% of the process value or ±0.8°C, whichever greater) ±1 digit max.

(

±0.3% of the process value or ±1.5°F, whichever greater) ±1 digit max.

Hysteresis 0.0

°C/°F to 99.9°C/°F for ON/OFF control only (in units of 0.1°C/°F)

Cooling coefficient 0.0 to 10.0 (in units of 0.1)
Proportional band 0.0

°C/°F to 999.9°C/°F (in units of 0.1°C/°F)

Cooling side: Cooling coefficient x Proportional band

Integral (reset) time 0 to 3,999 s (in units of 1 s) (for both heating and cooling)
Derivative (rate) time 0 to 3,999 s (in units of 1 s) (for both heating and cooling)
Control period Heating side:1 to 99 s (in units of 1 s)

Cooling side: 1 to 99 s (in units of 1 s)

Sampling period Approx. 200 ms for 8 control points
Dead band/overlap ba nd
Alarm output setting range

−999°C/°F to 999°C/°F (in units of 1°C/°F)

−999°C/°F to 9999°C/°F, 0 to 9999°C/°F (upper- and lower-limit alarm) (in units of 1°C/°F)

−999.9°C/°F to 9999.9°C/°F, 0.0 to 9999.9°C/°F (upper- and lower-limit alarm) (in units of 0.1°C/°F)

Fuzzy strength 0% to 99% (in units of 1%)
Fuzzy scale 1 0.2
Fuzzy scale 2 0.02

°C/°F to 999.9°C/°F (in units of 0.1°C/°F)

°C/s or °F/s to 99.99°C/s or °F/s (in units of 0.01°C/s or °F/s)

Set value backup Lithium battery
Set value backup period 10 years min. at room temperature
Insulation resistance 20 M

Ω min. between the FG terminal and all analog input terminals (at 500 VDC)

Dielectric strength A leakage current of 1 mA A C max. with 500 V AC f or 1 minutes between the FG terminal and all analog

input terminals

Vibration resistance

Malfunction: 10 to 55 Hz, 10 m/s
Destruction: 10 to 55 Hz, 20 m/s

Shock resistance

Malfunction: 150 m/s
Destruction: 200 m/s

Ambient temperature O perating:

Storage:

2

(15.3G), 3 times each in 6 directions

2

(20.4G), 3 times each in 6 directions

−10°C to 55°C (with no icing or condensation)

−25°C to 65°C (with no icing or condensation)

2

(1G) for 10 min each in X, Y , and Z directions

2

(2G) for 2 hrs each in X, Y, and Z directions

Ambient humidity Operating: 35% to 85%

Storage: 35% to 95%

Dimensions Without casing: 169.5 x 192 x 58 mm max.

With casing: 173.5 x 200 x 65 mm max.

Degree of protection IP00
Weight Without casing: 900 g max.

With casing: 1,700 g max.

EMC Em ission Enclosure: EN55011 Group 1 class A

Immunity ESD: EN61000-4-2:4 kV contact discharge (level 2)

8 kV air discharge (level 3)

Immunity RF-interference: ENV50140: 10 V/m (amplitude modulated, 80 MHz to 1 GHz)

(level 3)

10 V/m (pulse modulated, 900 MHz)
Immunity Conducted Disturbance: ENV50141: 10 V (0.15 to 80 MHz) (level 3)
Immunity Burst: EN61000-4-4:2 kV power-line (level 3)

Approved standards Conforms to EN50081-2, EN50082-2 (see note 3)

Note: 1. The measurement accuracy of the E5ZE used with a thermocouple B at 400°C or 750°F max. is not guaranteed. The following

measurement accuracy values are applied to the E5ZE.
K and T at
K and T at
R, S, and W at 200
R, S, and W at 400

2. The measurement accuracy of the E5ZE used with any thermoc ouple is 1
temperature ranges to increase the measurement accuracy to as high as 0.1
K thermocouple: 0.0
T or U thermocouple: 0.0
N thermocouple: 400.0

−100°C max. and U: ±3°C ±1 digit max.

−100°F max. and U: ±5.4°F ±1 digit max.
°C max., and B at 1,000°C max.: ±4°C ±1 digit max.
°F max., and B at 1,800°F m a x.: ±7.2°F ±1 digit max.

°C/°F. The thermocouple can be used under the following

°C/°F.
°C to 1,300.0 °C, 0.0 °F to 2,300.0 °F
°C to 400.0 °C, 0.0 °F to 700.0 °F

°C to 1,300.0 °C, 700.0 °F to 2,300.0 °F

J, E, L, or PLII thermocouple: Any temperature

3. To ensure EMC conformance, refer to Wiring for Conformance to the EMC Directives on page 16.

6 Multipoint Temperature Controller E5ZE