OLYMPUS C-200 Zoom Adjustment Method V1R4
C. ADJUSTMENT METHOD
C-200 ZOOM/D-510 ZOOM
C. ADJUSTMENT METHOD
[1] TABLE FOR SERVICING TOOLS .......................................................................... C-2
[2] EQUIPMENT ........................................................................................................... C-2
[3] ADJUSTMENT ITEMS AND ORDER ..................................................................... C-2
[4] SETUP .................................................................................................................... C-2
[5] CONNECTING THE CAMERA TO THE COMPUTER ............................................ C-3
[6] USB STORAGE INFORMATION REGISTRATION ................................................. C-4
[7] ADJUST SPECIFICATIONS ................................................................................... C-4
1. 5.1 V (A) VOLTAGE ADJUSTMENT ................................................................... C-4
2. 3.7 V (L) VOLTAGE ADJUSTMENT....................................................................C-4
3. LENS ADJUSTMENT .........................................................................................C-5
4. AWB ADJUSTMENT........................................................................................... C-5
5. COLOR MATRIX ADJUSTMENT ........................................................................ C-5
6. CCD DEFECT DETECT ADJUSTMENT ............................................................ C-6
7. CCD BLACK POINT AND WHITE POINT DEFECT DETECT ADJUSTMENT .. C-6
8. LCD PANEL ADJUSTMENT ..............................................................................C-6
8-1. LCD H AFC ADJUSTMENT .......................................................................C-6
8-2. LCD RGB OFFSET ADJUSTMENT ........................................................... C-6
8-3. LCD GAIN ADJUSTMENT ........................................................................C-7
8-4. LCD BLUE BRIGHTNESS ADJUSTMENT ...............................................C-7
8-5. LCD RED BRIGHTNESS ADJUSTMENT ................................................. C-7
8-6. LCD VCOM PP ADJUSTMENT.................................................................C-8
[8] ADJUSTMENT ITEMS ............................................................................................C-8
SIMENS STAR CHART ................................................................................................... C-9
CHECKING OF LENS UNIT ..........................................................................................C-10
C-1 Ver.1/Rev.4
C. ADJUSTMENT METHOD
C-200 ZOOM/D-510 ZOOM
[1] Table for Servicing Tools
Ref. No. Name Part code
J-1
J-2
J-3
J-4
J-4 Chart for color adjustment
Note: J-1 color viewer is 100 - 110 VAC only.
Color viewer 5,100 K
Siemens star chart
Calibration software
Extension cord
Number
1
1
1
1
1
VJ8-0007
VJ8-0179
VJ8-0180
VJ8-0155
J-1 J-2
J-3
J-4
[2] Equipment
1. Oscilloscope
2. Digital voltmeter
3. AC adaptor
4. PC (IBM R -compatible PC, Pentium processor, Window
98 or Me)
[3] Adjustment Items and Order
1. 5.1 V (A) Voltage Adjustment
2. 3.7 V (L) Voltage Adjustment
3. Lens Adjustment
4. AWB Adjustment
5. Color Matrix Adjustment
6. CCD Defect Detect Adjustment
7. CCD Black Point And White Point Defect Detect Adjust-
ment
8. LCD Panel Adjustment
8-1. LCD H AFC Adjustment
8-2. LCD RGB Offset Adjustment
8-3. LCD Gain Adjustment
8-4. LCD Blue Brightness Adjustment
8-5. LCD Red Brightness Adjustment
8-6. LCD VcomPP Adjustment
Note:
1. If the lens, CCD, board and changing the part in item 3-
7 replace, it is necessary to adjust again. 4-6 adjustments
other than these should be carried out in sequence. Item
7 adjustment should be carried out after item 4.
J-5
[4]. Setup
1. System requirements
Windows 98 or Me
IBM R -compatible PC with pentium processor
CD-ROM drive
3.5-inch high-density diskette drive
USB port
40 MB RAM
Hard disk drive with at least 15 MB available
VGA or SVGA monitor with at least 256-color display
2. Installing calibration software
1. Insert the calibration software installation diskette into
your diskette drive.
2. Open Explorer.
3. Copy the DscCalDI_127 folder on the floppy disk in the
FD drive to a folder on the hard disk.
3. Installing USB drive
Install the USB drive with camera or connection kit for PC.
4. Color Viewer
Turn on the switch and wait for 30 minutes for aging to take
place before using Color Pure.
C-2 Ver. 1
C-200 ZOOM/D-510 ZOOM
[5] Connecting the camera to the computer
1. Line up the arrow on the cable connector with the notch on the camera's USB port. Insert the connector.
2. Locate a USB port on the back of your computer.
C. ADJUSTMENT METHOD
To USB port
USB cable
AC adaptor
C-3Ver. 1
C. ADJUSTMENT METHOD
C-200 ZOOM/D-510 ZOOM
[6] USB Storage Information Registration
USB storage data is important for when the camera is connected to a computer via a USB connection.
If there are any errors in the USB storage data, or if it has
not been saved, the USB specification conditions will not be
satisfied, so always check and save the USB storage data.
Preparation:
POWER switch: ON
Adjustment method:
1. Connect the camera to a computer. (Refer to [5] Connecting the camera to the computer on the page C-3.)
2. Double-click on the DscCalDi127.
3. Click on the Get button in the USB storage window and
check the USB storage data.
VID: OLYMPUS
PID: C-200Z/D-510Z
Serial:
Rev. : 1.00
4. Check the “Serial” in the above USB storage data. If the
displayed value is different from the serial number printed
on the base of the camera, enter the number on the base
of the camera. Then click the Set button.
5. Next, check VID, PID and Rev. entries in the USB storage data. If any of them are different from the values in
3. above, make the changes and then click the corresponding Set button.
[7] Adjust Specifications
[ST1 board (Side B/A)]
VR502
CL560
CL528
VR504
Side B
Side A
Calibration
AWB
Focus
UV Matrix
Cal Mode
Cal Data
USB strage
VID
Get
PID
Set
OK
OK
Upload
Firmware
Image
Initialize
EVF
LCD Type
LCD
R Bright
RGB Offset
Tint
H AFC Test
Serial
Set
Set
Rev.
B Bright
Gain
Phase
Set
Set
VCOMDC
VCOMPP
Setting
Language
Video Mode
Note:
Voltage adjustment is necessary to repair in the ST1 board
and replace the parts.
Preparation:
1. Short Pins 1 and 2 of the S1401 card switch on the ST1
circuit board.
2. Connect the ST1 board and the SY1 board with extension cord.
3. Connect LCD panel.
4. Insert the card.
5. Turn on the power switch, and then set the camera mode.
6. Turn on the LCD monitor switch.
1. 5.1 V (A) Voltage Adjustment
Measuring Point
Measuring Equipment
ADJ. Location
ADJ. Value
Adjustment method:
1. Adjust with VR502 to 5.10 ± 0.05 V.
CL528
Digital voltmeter
VR502
5.10 ± 0.05 V
2. 3.7 V (L) Voltage Adjustment
Measuring Point
Measuring Equipment
ADJ. Location
ADJ. Value
CL560
Digital voltmeter
VR504
3.70 ± 0.05 V
C-4 Ver. 1
Loading...