NHD–4 is a dual mode handportable Cellular phone product for the North
American dual mode CDMA/AMPS system.
The transceiver consist of four modules: UI–flex, RF/system module,
battery pack and mechanics.
NHD–4 offers analog and digital mode full rate speech services defined in
IS–96 and in analog mode provides six power levels at a maximum power
level of 0.6W ERP (450mW into 50 Ohm load) in power class III. The
transceiver has a retractable antenna and a connector for external
antenna and accessories. The user communicates with the phone via
LCD–display, keyboard and some audible tones.
The transceiver will support an Analog PCMCIA Card.
NHD–4 can be connected to different accessories such as chargers,
holders, hands–free units, data–adapters and handset through the bottom
system connector.
General Information
Original 11/97
NOKIA1
Figure 1. NHD–4
Page 2–3
NHD–4
PAMS
General Information
Technical Documentation
List of Modules
Nokia1 NHD–4NX
Table 1. Nokia1 NHD–4NX 0500322
Name of moduleType codeMaterial
code
User interfaceDU8D0200521Nokia 1
System/RFGR10200519CDMA 800 MHz Radio Module
MechanicsMNHD4NX0260523Nokia 1
Notes
Units and Accessories
Table 2. List of Transceivers
Name of TranceiverDesign VersionType CodeMaterial Code
Fast Travel ChargerACH–4U0675012USA model
Cigarette Lighter ChargerLCH–20675005Universal
Desktop ChargerCHH–20675022Universal
HF Desktop ChargerCHH–80675026Universal
AC AdapterACS–6U0680018USA model, needed for CHH–8
Page 2–4
Original 11/97
PAMS
NHD–4
Technical Documentation
Table 5. List of Mobile Installation Accessories
NameType CodeMaterial CodeNotes
Mobile HolderMBH–60620009
Mobile HF Charging HolderMCH–80620010
HF Junction BoxHFJ–30694009
External HF SpeakerHFS–60692005
HF MicrophoneHFM–40690002Original
HF MicrophoneHFM–100690009New , ”mouse” type
Power CablePCH–40730009
External Audio HandsetHSU–10640047
Compact HFPHF–10700017
Power CableLCP–20680022
Mounting PlateMKE–10650007
Swivel KitHHS–106500063 screws
Swivel KitHHS–606500194 screws
General Information
Cable HolderCKH–10620016
Table 6. List of Data Accessories
NameTypeMaterial codeNotes
PC–Link AdapterDAU–20750029
Data CableDKH–19780084CHH–8 → PC Link
Data CableDKH–20730041Adapter Cable
Data CableDKH–50730038HP–PC Link
Table 7. List of General Accessories
NameType codeMaterial codeNotes
Carry StrapSWH–10720005
Belt ClipBCH–20720022
HeadsetHFS–110690010Over the head headset
HeadsetHDC–20694017Button headset
Original 11/97
Page 2–5
NHD–4
PAMS
General Information
Technical Documentation
Basic Specifications
Table 8. Basic Specifications
ParameterNotes
Cellular systemCDMA/AMPS
TX frequency band824.010...848.970 MHz
RX frequency band869.010...893.970 MHz
Duplex spacing45 MHz
Number of RF channels832 Analog (see IS–95 6.1.1.1 for CDMA)
Channel spacing30 kHz Analog (see IS–95 2.1.1.1 for CDMA)
Power ClassIII
Maximum output power600 mW ERP (AMPS) 200 mW (CDMA)
Method of frequency synthesisDigital phase–locked loops
Frequency controlVCTCXO
Receiver typeIF, linear in D–mode, nonlinear in A–mode
Modulator typeI/Q–baseband in D–mode, FM–modulator in A–mode
Operational Voltage5.3V...8.8 V
Technical Specifications
Modes of Operation
NHD–4 operates in three modes:
1. In AMPS mode it operates in analog paging and voice channels.
2. In digital mode it operates on digital synch, paging pilot and traffic
channel.
3. Test mode (Local mode) used for troubleshooting and diagnostic
testing.
TX frequency band824.04...848.970 MHz
RX frequency band869.04...893.970 MHz
Duplex spacing45 MHz
Number of RF channels832 Analog
Channel spacing30 kHz Analog
Analog Mode
Table 11. Transmitter Specifications for ANALOG mode
Modulation methodFM
Deviation, speech and ST±12 kHz peak
General Information
Deviation, WBD±8 kHz peak
Deviation, SAT±2 kHz peak
Deviation, voice and SAT±14 kHz peak
Compressor2:1
Output RF power (ERP from int. ant.)26.3...6.3 dBm
Output RF power (ERP from int. ant.)26.8...6.8 dBm
Number of power levels (2–7)6
Carrier on/off switching time< 2ms
Frequency stability±2.5 ppm
Harmonic and spurious emissions43 +10*log (Po W) dB below carrier
Table 12 Receiver Specifications, for ANALOG mode
Sensitivity, 12 dB SINAD (C)–116 dBm
Hum and noise32 dB
RSSI dynamic range60 dB
Adjacent channel selectivity16 dB
Alternate channel selectivity60 dB
IMD attenuation, close spaced65 dB
IMD attenuation, wide spaced70 dB
Original 11/97
Page 2–7
NHD–4
PAMS
General Information
Technical Documentation
Digital Mode
Table 13. Transmitter Specifications for CDMA mode
TX noise floor with TX disabled–61 dBm/MHz for all frequencies between 824 and 849 MHz
TX noise floor at RX band with
Max. output power
TX power control methodOutput_power (dBm) = –73 dBm – Receive_power (dBm) +
TX power initial accuracy+/–9 dB within value as specified by TX control method
–42 dBc in a 30 KHz BW for offsets > 885 KHz from center F
–54 dBc in a 30 KHz BW for offsets > 1.98 MHz from center
F
or –60 dBm/30 KHz and –54 dBm/1.23 MHz for offsets >
885 KHz from center Frequency
FCC rules
gate off)
–173 dBm/Hz (TBD) at RX input port
TX offset (dB). Open + closed loop AGC.
TX duty cycle1/1, 1/2, 1/4, 1/8 variable rate with random slots. A slot is
1.25 ms. Rate is controlled by voice activity
TX offset control methodFrom base station with one increments or decrement every
1.25 ms (but only during active transmit slot)
TX offset control step size1 dB +/–0.5, and +/–20% over 10 steps in same direction
TX offset range+/–32 dB (+/–24 dB step range, +/–8 dB preset offset)
Modulator typeI/Q modulator, OQPSK format
Peak to rms after modulation6 dB
I/Q Modulator phase error+/–6 deg (+/– 4 deg for D/A and filter)
I/Q Modulator gain balance+/–0.65 dB (+/–0.35dB for D/A and filter)
I/Q Modulator input level1Vpp