Nissan VERSA SEDAN 2014 LC2 Kai Navigation Manual

2014 NAVIGATION

SYSTEM

OWNER’S MANUAL

For your safety, read carefully and keep in this vehicle.

FOREWORD

NISSAN NAVIGATION SYSTEM HELPDESK CONTACT INFORMATION

For assistance or inquiries about the NISSAN Navigation System, or to order updated map data, contact the NISSAN NAVIGATION SYSTEM HELPDESK at:

ADDRESS: P.O. Box 1588,

•

Orem, UT 84059-992

E-MAIL: Nissan-Navi-Info@navteq.com

•

WEB SITE: www.navigation.com or

•

www.nissan.ca

PHONE: 1-888-661-9995

•

HOURS: 6:00 AM to 5:00 PM

•

(Paciﬁ c Time)

NISSAN CONSUMER AFFAIRS DEPARTMENT

For assistance or inquiries about the NISSAN warranty, service or general questions, contact the NISSAN Consumer Affairs Department at:

For U.S. customers Nissan North America, Inc. Consumer Affairs Department P.O. Box 685003 Franklin, TN 37068-5003 1-800-NISSAN-1 (1-800-647-7261)

For Canadian customers Nissan Canada Inc. 5290 Orbitor Drive Mississauga, Ontario L4W 4Z5 1-800-387-0122

Thank you for purchasing a NISSAN vehicle This user’s manual is for the navigation system only. This manual contains operating instructions for the NISSAN Navigation System offered in your NISSAN vehicle.

Please read this manual carefully to ensure safe operation of the navigation system.

Because of possible speciﬁ cation changes

•

and optional equipment, sections of this manual may not apply to your vehicle. All information, speciﬁ cations and illustra-

•

tions in this manual are those in effect at the time of printing. NISSAN reserves the right to change speciﬁ cations or design at any time without notice. Do not remove this manual from the vehicle

•

when selling this vehicle. The next user of this navigation system may need the manual.

Table of

Introduction

Contents

Getting started

Map settings

Navigation

Other settings

General system information

Troubleshooting guide

Index

1 Introduction

How to use this manual ............................1-2

For safe operation ..............................1-2

Reference symbols .............................1-2

Safety information .................................1-2

Laser product .....................................1-3

HOW TO USE THIS MANUAL SAFETY INFORMATION

This manual uses special words, symbols and icons that are organized by function.

Please refer to the following items to understand how to use this manual properly.

FOR SAFE OPERATION

WARNING

Indicates the presence of a hazard that could cause death or serious personal injury. To avoid or reduce the risk, the procedures must be followed precisely.

CAUTION

Indicates the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle. To avoid or reduce the risk, the procedures must be followed carefully.

NOTE:

Indicates items that help you understand and maximize the performance of your vehicle. If ignored, they may lead to a malfunction or poor performance.

REFERENCE SYMBOLS

INFO:

Indicates information that is necessary for efficient use of your vehicle or accessories.

Reference page:

Indicates the title and page that you should refer to.

NAV:

This is an example of how a button on the control panel will be shown.

“Route”:

This is an example of a key/item displayed on the screen.

This system is primarily designed to help you reach your destination, and it also performs other functions as outlined in this manual. However, you, the driver, must use the system safely and properly. Information concerning road conditions, traffic signs and the availability of services may not always be up-to-date. The system is not a substitute for safe, proper and legal driving.

Before using the navigation system, please read the following safety information. Always use the system as outlined in this manual.

WARNING

● To operate the navigation system, first park the vehicle in a safe location and set the parking brake. Operating the system while driving can distract the driver and may result in a serious accident.

● Do not rely on route guidance alone. Always be sure that all driving maneuvers are legal and safe in order to avoid accidents.

● Do not disassemble or modify this system. If you do, it may result in accidents, fire or electrical shock.

1-2 Introduction

LASER PRODUCT

● If you notice any foreign objects in the system hardware, spill liquid on the system or notice smoke or a smell coming from it, stop using the system immediately and contact a NISSAN dealer. Ignoring such conditions may lead to accidents, fire or electrical shock.

CAUTION

● Do not use this system if you notice any malfunctions such as a frozen screen or the lack of sound. Continued use of the system may result in accidents, fire or electrical shock.

● Some states/provinces may have laws limiting the use of video screens while driving. Use this system only where it is legal to do so.

● Extreme temperature conditions [below -4 °F (-20 °C) and above 158 °F (70 °C)] could affect the performance of the system.

NOTE:

Do not keep the navigation system running with the engine stopped. Doing so may discharge the vehicle battery. When you use the navigation system, always keep the engine running.

WARNING

● Do not disassemble or modify this system. There are no user serviceable parts in this navigation system.

● If maintenance, adjustments and operations other than those specified in this manual are attempted, injury due to laser radiation and exposure could occur.

Introduction 1-3

SiriusXM services require a subscription after a trial period and are sold separately or as a package. Our satellite

service is available only in the 48 contiguous USA and DC. For more information visit www.siriusxm.com. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect spe-

cifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone my affect wireless performance.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by DENSO CORPORATION is under license. Other trademarks and trade names are those of their respective owners.

Required SiriusXM Satellite Radio and SiriusXM Traffic monthly subscriptions are sold separately. SiriusXM Traffic are only available in select markets. For more information, see www.siriusxm.com/siriusxmtraffic

Required SiriusXM Satellite Radio and SiriusXM Travel Link monthly subscriptions are sold separately. SiriusXM Travel Link is only available in select markets. For more information, see www.siriusxm.com/travellink

App Store

Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Google Play™

Google Play is a trademark of Google Inc.

Google

1-4 Introduction

2 Getting started

Control buttons and functions.......................2-2

Control panel (Type A) ..........................2-2

Control panel (Type B) ..........................2-3

Control panel (Type C) ..........................2-4

Steering wheel switch (Type A) ..................2-5

Steering wheel switch (Type B) ..................2-5

Steering wheel switch (Type C) ..................2-6

Basic operation ...................................2-7

Touch screen operation .........................2-7

Menu screen operation..........................2-8

How to input characters.........................2-9

CONTROL BUTTONS AND FUNC-

TIONS

CONTROL PANEL (Type A)

VOL (volume) control knob/POWER button:

䊐

Rotate clockwise to increase the volume or counterclockwise to lower the volume.

Press to turn the audio system on or off.

Touch screen display

䊐

TUNE-SCROLL dial / ENTER/AUDIO but-

䊐

ton:

Turn to scroll through the items in a list. Press to select a menu item. When the screen is not displaying a list or menu, the knob is used to control the audio system.

Press the ENTER/AUDIO button to select a highlighted item on the screen.

LNV2446

䊐

BACK button:

Press to return to the previous screen or to delete the last inputted letter if a touch keyboard is displayed on the screen.

MAP button:

Press to display the current location map screen.

NAV button:

Press to access the functions of the Navigation system.

button:

Press to access the system settings.

button:

Press to change the display brightness between day and night modes. While the mode is being displayed, the brightness can be adjusted using the TUNE/SCROLL dial.

Press and hold for more than two seconds to switch the display to a larger display of the digital clock.

“DISPLAY SETTINGS” (page 5-3)

2-2 Getting started

CONTROL PANEL (Type B)

VOL (volume) control knob/POWER button:

䊐

Rotate clockwise to increase the volume or counterclockwise to lower the volume.

Press to turn the audio system on or off.

Touch screen display

䊐

TUNE-SCROLL dial / ENTER/AUDIO but-

䊐

ton:

Turn to scroll through the items in a list. Press to select a menu item. When the screen is not displaying a list or menu, the knob is used to control the audio system.

Press the ENTER/AUDIO button to select a highlighted item on the screen.

LNV2479

䊐

BACK button:

Press to return to the previous screen or to delete the last inputted letter if a touch keyboard is displayed on the screen.

MAP button:

Press to display the current location map screen.

NAV button:

Press to access the functions of the Navigation system.

button:

Press to access the system settings.

button:

Press to change the display brightness between day and night modes. While the mode is being displayed, the brightness can be adjusted using the TUNE/SCROLL dial.

Press and hold for more than two seconds to switch the display to a larger display of the digital clock.

“DISPLAY SETTINGS”

(page 5-3)

Getting started 2-3

CONTROL PANEL (Type C)

VOL (volume) control knob/POWER button:

䊐

Rotate clockwise to increase the volume or counterclockwise to lower the volume.

Press to turn the audio system on or off.

Touch screen display

䊐

TUNE-SCROLL dial / ENTER/AUDIO but-

䊐

ton:

Turn to scroll through the items in a list. Press to select a menu item. When the screen is not displaying a list or menu, the knob is used to control the audio system.

Press the ENTER/AUDIO button to select a highlighted item on the screen.

LNV2477

䊐

BACK button:

Press to return to the previous screen or to delete the last inputted letter if a touch keyboard is displayed on the screen.

MAP button:

Press to display the current location map screen.

NAV button:

Press to access the functions of the Navigation system.

button:

Press to access the system settings.

button:

Press to change the display brightness between day and night modes. While the mode is being displayed, the brightness can be adjusted using the TUNE/SCROLL dial.

Press and hold for more than two seconds to switch the display to a larger display of the digital clock.

“DISPLAY SETTINGS” (page 5-3)

2-4 Getting started

Altima

LNV2499

STEERING WHEEL SWITCH (Type A

Volume increase button

䊐

Increases the volume of the voice guidance given by the Navigation System if pressed while the voice guidance is speaking. If the volume increase button is pressed at any other time, only the volume of the active screen (phone, SMS playback, Voice Recognition system [if so equipped], audio system) will be increased.

Volume decrease button

䊐

Decreases the volume of the voice guidance given by the Navigation System if pressed while the voice guidance is speaking. If the volume decrease button is pressed at any other time, only the volume of the active screen (phone, SMS playback, Voice Recognition system [if so equipped], audio system) will be decreased.

For more information about the audio system, Bluetooth® Hands-Free Phone System and Voice Recognition system (if so equipped), see

)

the vehicle’s Owner’s Manual.

Sentra

LNV2500

STEERING WHEEL SWITCH (Type B

Volume control button

䊐

Increases or decreases the volume of the voice guidance given by the Navigation System if pressed while the voice guidance is speaking. If the volume button is pressed at any other time, only the volume of the active screen (phone, SMS playback, Voice Recognition system [if so equipped], audio system) will be adjusted.

)

Getting started 2-5

Xterra and Frontier

For more information about the audio system, Bluetooth® Hands-Free Phone System and Voice Recognition system (if so equipped), see the vehicle’s Owner’s Manual.

LNV2501

Rogue

LNV2502

STEERING WHEEL SWITCH (Type C

Volume increase button

䊐

Volume decrease button

䊐

For more information about the audio system, Bluetooth® Hands-Free Phone System and Voice Recognition system (if so equipped), see

)

the vehicle’s Owner’s Manual.

2-6 Getting started

BASIC OPERATION

TOUCH SCREEN OPERATION

The same operations described for the scrolling dial are possible using touch screen operation.

LNV2443 LNV2440

Examples of touch screen operation

Selecting an item:

When any item is touched, the next screen is displayed.

Adjusting:

Touch the “+”, “-”, “>” or “<” key to adjust a setting.

Getting started 2-7

LNV0921

Scrolling through a message or list:

Turn the TUNE-SCROLL dial to scroll through a message or a list. When scrolling a lengthy list, you can also touch the screen and slide your finger along the scroll bar where shown to scroll more quickly. Touching the up or down arrow will move between pages of the list.

(Type A)

MENU SCREEN OPERATION Menu screens and their purpose

2-8 Getting started

LNV2448

(Type B)

Press one of the application buttons to activate the corresponding menu screen:

● NAV (Navigation)

●

or MENU

LNV2478

(Type C)

LNV2476

How to select a menu item

1. As an alternative to using the touch screen, turn the scrolling dial clockwise or counterclockwise to scroll through the menu items until the preferred item is highlighted.

2. To select the preferred item, press the scrolling dial.

3. Press the BACK or The previous screen will be displayed and the changes will be saved.

BACK button.

HOW TO INPUT CHARACTERS Character (letter and number) input

screen

Alphanumeric characters are used when setting a destination, searching for an address, editing stored locations, etc.

LNV2415

1. Touch characters on the touch keyboard and they will appear in the field at the top of the screen. When the entry is complete, touch the “OK” key.

Alternatively, use the scrolling dial to highlight a character and press the dial to select that character.

NOTE:

● Press the last inputted character or to return to the previous screen if no characters have been inputted.

● On every character entry screen, the touch keyboard will display only the letters that are possible to enter after the current letter.

● Symbol and number keys are available when the “123/ABC” key is touched.

BACK button to delete the

● Touch the “123/ABC” key to toggle the display between the touch keyboard for letters and the touch keyboard for numbers and symbols.

2. To delete the last entry, touch the “Delete” key or hold it to delete all entries at once.

3. After finalizing the entries, touch the “OK” key or touch the “List” key for the completed list screen.

NOTE:

● If a phrase is being entered that has been previously entered into the system, the matched text may appear in light gray. Touch “OK” to search for the matched text. Touch “List” to search for both the matched text and entered text.

Getting started 2-9

MEMO

2-10 Getting started

3 Map settings

Map types ........................................3-2

2-Dimensional (2D) view . . . .....................3-2

2-Dimensional North Up (2DN) view ..............3-2

3-Dimensional (3D) view . . . .....................3-2

Screen information (2D, 2DN or 3D)..............3-3

Moving a map .....................................3-4

Returning to the current vehicle location...........3-5

Map options menu screen ..........................3-5

Changing the map scale............................3-6

Map scale .....................................3-7

Looking at information on the map ...................3-7

Map symbols...................................3-7

Map settings for the map screen ....................3-9

Lane information..................................3-11

Map SD-card ....................................3-11

How to handle the SD-card.....................3-12

SD-card replacement ..........................3-12

How to order map data updates.................3-12

About the map data............................3-13

End-user terms................................3-14

MAP TYPES

2-DIMENSIONAL (2D) VIEW

The 2D map is a two-dimensional (flat) representation of the map data, similar to a road map, focused on the vehicle’s position (vehicle icon).

“SCREEN INFORMATION (2D, 2DN or 3D)” (page 3-3)

“MAP SETTINGS FOR THE MAP SCREEN” (page 3-7)

LNV2455

2DN

2-DIMENSIONAL NORTH UP (2DN) VIEW

The 2DN map is a two-dimensional (flat) representation of the map data, similar to a road map, focused on the vehicle’s position (vehicle icon) with the top of the map aligned North.

3-2 Map settings

LNV2454

LNV2456

3-DIMENSIONAL (3D) VIEW

The 3D map displays the map from an elevated perspective, providing a panoramic view over a long distance.

The map in 3D view always appears with the current forward direction facing up (heading up).

SCREEN INFORMATION (2D, 2DN or 3D)

“Voice” key

䊐

Touch to repeat the voice guidance while a route is active. Touch and hold for two seconds to toggle the voice guidance on or off (button will be grayed out when voice guidance is turned off). This option is available only when a route is set.

Audio information

䊐

Indicates the radio station, CD track number or other audio information currently playing.

Next maneuver road name

䊐

Indicates the name of the next road in the route guidance. This is only shown if route guidance is active.

Clock

䊐

Indicates the current time.

LNV2206

Direction indicator and distance to next ma-

䊐

neuver on the route

When route guidance is active but you have deviated from the route, this area displays a compass icon with an arrow indicating the destination direction.

When route guidance is active and you are on the route, this area indicates the distance (in miles or kilometers) to the next point and the turning direction at that point.

When the “Voice” key is not shown on the screen (such as when an audio screen is displayed on the screen), touch the direction indicator to repeat the voice guidance while a route is active. Touch and hold for two seconds to toggle the voice guidance on or off.

Estimated time of arrival and distance to

䊐

destination or remaining time of travel and distance to destination.

Touch this button to switch the indicator between estimated arrival time and remaining travel time. This indicator only appears once the destination is set and the route guidance is initiated. The estimated arrival time may not switch to the estimated arrival time for the destination’s time zone if a time zone line is crossed as part of the route.

Map settings 3-3

MOVING A MAP

Current road indicator

䊐

The location of where the car is positioned.

Vehicle icon

䊐

Indicates the current location and direction of the vehicle.

Suggested route

䊐

Appears as a bold blue line during route guidance.

Scale indicator

䊐

Indicates the scale of the map.

Compass icon

䊐

Indicates the direction of the map. Touch this icon to switch the map view between the North Up, Heading Up (or actual direction) and 3D modes.

“Presets” key

䊐

This option toggles on and off with the “Menu” key and displays a touch menu of the radio presets on the screen. For more information about the audio system, see the vehicle Owner’s Manual.

Zoom in and zoom out keys

䊐

Touch to zoom the map in or out.

“Options” key

䊐

Touch this key to access the map options menu screen.

“MAP OPTIONS MENU SCREEN” (page 3-5)

LNV2463

To scroll the map in either direction:

1. Touch and release the screen anywhere on the map.

2. Touch the screen again and move your finger along the screen in the direction you wish to scroll.

After releasing and touching the map again, a marker will be displayed at the point touched and, if possible, the position determined.

3-4 Map settings

MAP OPTIONS MENU SCREEN

NOTE:

When the current location of the vehicle is recognized, the street name will be displayed at the bottom of the screen. When scrolling a map and an area that is not a road, city or POI is touched, coordinates corresponding to the marker’s position are displayed at the bottom of the screen.

RETURNING TO THE CURRENT VEHICLE LOCATION

The basic map screen displays the current location of the vehicle. The current location can be displayed again even after the map is moved, or after the menu screen is displayed.

Press the MAP button or the BACK or BACK button and the current location will be displayed on the map.

The Map Options menu allows you to quickly store the current position, show position information or destination information, and adjust the map settings.

LNV2457

1. Touch the “Options” key while the route guidance map is displayed.

2. The following options are available for selection:

● Enter Destination

Select to open the navigation screen for entering an address.

● Turn List

Select to display all of the turns and waypoints along the route.

● Cancel Route

Select to cancel entire route or waypoints along route.

● POIs Along Route

Select to choose the types of points of interest to display along the active route. Available options are gas stations, restaurants, ATMs, parking, rest areas, hotels, dealerships and airports.

Map settings 3-5

CHANGING THE MAP SCALE

NOTE:

Some places of interest on divided highways may show the equivalent place of interest on the opposite side of the road (such as a rest area) as being closer than the place in your traveling direction. Confirm location of the place before following the route.

● Traffic Select to display all traffic events on route and options to avoid roads along route.

● Show Route On Map Select to display the entire route on the screen. The view will zoom to the necessary level in order to show both the starting point and destination on the screen.

● Routing Options Select to view options available to customize route. Avoiding specific roads, dynamic guidance, route type and minimizing freeways, types of roads and ferries can all be adjusted.

● Show Position Information Select to display the latitude, longitude and altitude for the current position of the vehicle. Location can also be stored to the Address Book.

● Show Waypoints Select to add or show list of waypoints along route.

● Guidance & Map Settings Select to toggle guidance information and map settings options.

“MAP SETTINGS FOR THE MAP SCREEN” (page 3-7)

3-6 Map settings

LNV2462

When using the “+” or “-” for zooming in or out, the scale on the bottom left side of the screen changes to indicate the new scale level.

+ 56 hidden pages