Nec VT610 user Manual

Download

Page 1

Projector

WT615/WT610

User’s Manual

The WT615 projector is not distributed in the U.S.A or Canada.

Page 2

Important Information

Safety Cautions

Precautions

Please read this manual carefully before using your NEC WT615/WT610 Projector and keep the manual handy for future reference. Your serial number is located on the right side of your projector. Record it here:

CAUTION

To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.

This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided. The information should be read carefully to avoid problems.

WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.

DOC Compliance Notice (for Canada only)

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Acoustic Noise Information Ordinance-3. GSGV (for Germany only):

The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.

CAUTION

Do not look into the laser pointer while it is on and do not point the laser beam at a person. Serious injury could result.

This label is underneath the remote control.

WARNING TO CALIFORNIA RESIDENTS:

Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

Page 3

Important Information

RF Interference (for USA only)

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Solutions (America), Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cable is not supplied with this equipment please contact your supplier.

Important Safeguards

These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings.

Installation

1. For best results, use your projector in a darkened room.

2. Place the projector on a flat, level surface in a dry area away from dust and moisture.

3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm internal components.

5. Handle your projector carefully. Dropping or jarring can damage internal components.

6. Do not place heavy objects on top of the projector.

7. If you wish to have the projector installed on the ceiling: a. Do not attempt to install the projector yourself. b. The projector must be installed by qualified technicians in order to ensure proper operation and reduce the

risk of bodily injury.

c. In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-

dance with any local building codes.

d. Please consult your dealer for more information.

Place the projector in a horizontal position

The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.

10°

Page 4

Important Information

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside

your projector. Allow at least 4 inches (10 cm) of space between your projector and a wall.

2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.

Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified NEC service personnel.

3. Do not place any liquids on top of your projector.

4. Do not look into the mirror or the light source while the projector is on. Serious damage to your eyes could

result.

5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the

mirror is extensive, therefore any kind of abnormal objects that can redirect light coming out of the mirror, can cause unpredictable outcome such as fire or injury to the eyes.

6. Do not block the light path between the light source and the final mirror with any objects. Doing so could cause

the object to catch on fire.

7. The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power

supply fits this requirement before attempting to use your projector.

8. Handle the power cable carefully and avoid excessive bending.

A damaged cord can cause electric shock or fire.

9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.

10. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.

11. Do not handle the power plug with wet hands.

12. When using a LAN cable:

For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage.

CAUTION

• Do not try to touch the ventilation openings on the both sides as it can become heated while the projector is turned on.

• Do not attempt to move or carry the projector using the mirror cover. Doing so can result in the projector overturning and causing injury. Using the two side handles is the proper

way to move the projector. When carrying or transporting the projector, close and lock the mirror cover with the mirror cover lock switch.

• The carrying handles are designed for the purpose of carrying the projector. Do not hang from the projector by the carrying handles in a ceiling mounted installation. Doing so may result in the carrying handles separating from the unit or the projector may separate from the mount resulting in personal injury.

• Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select [Setup] → [Options] → [Fan Mode] → [High].)

• Do not unplug the power cable from the wall outlet under any one of the following circumstances. Doing so can cause damage to the projector:

* While the projector's lamp is on. * While the cooling fans are running. (The cooling fans continue to work for 90 seconds after the projector is

turned off).

* While the PC CARD Access Indicator lights. Doing so can damage your PC memory card.

iii

Page 5

Important Information

Lamp Replacement

•To replace the lamp, follow all instructions provided on page 134.

• Be sure to replace the lamp when the message “The lamp has reached the end of its usable life. Please replace the lamp.” appears. If you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.

If this happens, contact your NEC dealer for lamp replacement.

• Allow a minimum of 90 seconds to elapse after turning off the projector. Then turn off the main power switch, disconnect the power cable and allow 60 minutes to cool the projector before replacing the lamp.

Page 6

Table of Contents

Important Information ...........................................................................i

1. Introduction ...................................................................................... 1

 What's in the Box? ........................................................................................................ 2

 Introduction to the Projector ......................................................................................... 3

 Part Names of the Projector ......................................................................................... 5

Opening and Closing the Mirror Cover ................................................................... 6

Top Features ........................................................................................................... 7

Te r minal Panel Features ......................................................................................... 8

 Part Names of the Remote Control ............................................................................ 10

Battery Installation ................................................................................................ 12

Operating Range for Wireless Remote Control..................................................... 12

Remote Control Precautions ................................................................................. 12

Using the Remote Control in Wired Operation...................................................... 12

 Part Names and Functions of the Supplied Electronic Pen (WT615 only) ................. 13

Battery Installation ................................................................................................ 13

Electronic Pen Precautions ................................................................................... 13

2. Installation and Connections ....................................................... 14

 Setting Up the Screen and the Projector .................................................................... 16

 Making Connections ................................................................................................... 19

When Viewing a DVI Digital Signal ....................................................................... 19

Connecting Your PC or Macintosh Computer........................................................ 19

To connect SCART output (RGB) ......................................................................... 20

Using two Analog COMPUTER inputs simultaneously ......................................... 21

Connecting an External Monitor ........................................................................... 22

Connecting Your DVD Player................................................................................. 23

Connecting Your VCR or Laser Disc Player .......................................................... 24

Connecting to a Network....................................................................................... 25

Inserting and Removing a PC Card ...................................................................... 27

Connecting the Supplied Power Cable ................................................................. 29

3. Projecting an Image (Basic Operation)...................................... 30

 Tur ning on the Projector ............................................................................................. 31

 Adjusting the Position and Size of the Projected Image (Focus Adjustments) ........... 33

 Selecting a Source ..................................................................................................... 40

 Optimizing an RGB Image Automatically ................................................................... 41

 Tur ning Up or Down Volume ....................................................................................... 41

 Adjusting Pincushion or Barrel Distortion (Pincushion) .............................................. 42

 Using the Laser Pointer .............................................................................................. 44

쐊 Using the Electronic Pen (WT615 only)...................................................................... 45

쐎 Tur ning off the Projector ............................................................................................. 48

쐅 After Use..................................................................................................................... 49

Page 7

Table of Contents

4. Convenient Features ...................................................................... 50

 Tur ning Off the Image and Sound............................................................................... 51

 Freezing a Picture....................................................................................................... 51

 Using the Pointer ........................................................................................................ 51

 Enlarging and Moving a Picture.................................................................................. 52

 Getting Integrated Help .............................................................................................. 52

 Using a USB Mouse ................................................................................................... 53

 Using the Remote Mouse Function ............................................................................ 54

 Making Freehand Drawings on a Projected Image (ChalkBoard) .............................. 55

쐎

Storing Images Displayed on the Projector on the PC card or USB memory (Capture)

쐅 Preventing Unauthorized Use of the Projector ........................................................... 57

쐈 Using a USB Memory Device or USB Memory Card Reader ..................................... 62

쐉 Operation Using an HTTP Browser ............................................................................ 63

씈

Using the Projector to Operate a Computer Connected on a Network (Desktop Control Utility 1.0)

.......... 56

........ 66

5. Using the Viewer ............................................................................. 71

 Making the Most out of the Viewer Function ............................................................... 72

 Operating the Viewer Function from the Projector (playback) .................................... 73

쐋 Changing Background Logo ....................................................................................... 79

6. Using On-Screen Menu ................................................................. 80

 Using the Menus......................................................................................................... 81

 Menu tree ................................................................................................................... 82

 Menu Elements........................................................................................................... 84

 Menu Descriptions & Functions [Source] ................................................................... 85

쐄 Menu Descriptions & Functions [Adjust] ..................................................................... 88

쐂 Menu Descriptions & Functions [Setup] ..................................................................... 98

쐆 Menu Descriptions & Functions [Information] ........................................................... 126

쐊 Menu Descriptions & Functions [Reset] ................................................................... 129

7. Maintenance .................................................................................. 131

 Handling and Care of Mirror Surface ........................................................................ 132

쐇 Cleaning the Cabinet ................................................................................................ 133

쐋 Replacing the Lamp................................................................................................. 134

8. Appendix ......................................................................................... 137

 Troubleshooting ........................................................................................................ 138

 Specifications ........................................................................................................... 142

 Cabinet Dimensions ................................................................................................. 144

 Pin Assignments of D-Sub COMPUTER Input Connector ....................................... 145

 Compatible Input Signal List ..................................................................................... 146

 PC Control Codes and Cable Connection ................................................................ 147

 Using Software Keyboard ......................................................................................... 148

 Troubleshooting Check List....................................................................................... 149

Page 8

Introduction

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 What's in the Box? ....................................................... 2

 Introduction to the Projector ........................................ 3

 Part Names of the Projector ........................................ 5

Opening and Closing the Mirror Cover ................................................................... 6

Top Features........................................................................................................... 7

Te r minal Panel Features......................................................................................... 8

 Part Names of the Remote Control ........................... 10

Battery Installation ................................................................................................ 12

Operating Range for Wireless Remote Control .................................................... 12

Remote Control Precautions ................................................................................ 12

Using the Remote Control in Wired Operation ..................................................... 12

 Part Names and Functions of

the Supplied Electronic Pen (WT615 only) ............ 13

Battery Installation ................................................................................................ 13

Electronic Pen Precautions .................................................................................. 13

Page 9

 What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your Projector.

UNL

OCK

IRROR

LOCK

1. Introduction

Power cable (7N080204) US (7N080008) EU

Important

Information

For North America only

Registration card Limited warranty

For Europe only

Guarantee policy

Setup

Guide

NEC

Network

Setup Guide

Projector

Remote Control Cable (7N520019)

CD-ROM User’s manual and User Supportware 2

WT615 only

• Electronic pen and battery

(7N900611)

Remote control (7N900501)

USB cable (7N520045)

(AA⳯1)

Batteries (AAA ⳯ 2)

RGB/VGA signal cable (7N520032)

• Security sticker

• Mirror cleaning cloth (24BS7251)

• Dust-proof cover (24BS7272)

• USB memory device (7N960201)

See page 62.

• CD-ROM User Supportware 2 Plus (eBeam Interactive Software)

• eBeam Interactive Software Setup Guide

Page 10

1. Introduction

 Introduction to the Projector

This section introduces you to the WT615/WT610 Projector and describes key features and controls.

Congratulations on Your Purchase of the WT615/WT610 Projector

The WT615/WT610 is a sophisticated four aspherical mirror XGA projector that produces an enhanced display. With the WT615/WT610 you will be able to project images up to 100” (measured diagonally). Enjoy crisp and sharp large screen display from your PC, workstation or Macintosh computer, DVD player, VCR, satellite hookup, HDTV source, ) and images from your digital camera PC Card, compact flash memory or USB storage device. The WT615/WT610 provides for enhanced security options to help deter projector theft and provides for full projector control through the PC control port (mini DIN 8Pin) and LAN support. With input and output flexibility and a full function remote, the WT615/WT610 lets you enjoy larger than life viewing from a compact and easy to setup and use projector.

Features you’ll enjoy on the WT615/WT610:

• Extremely short focal length

• 40" to 100" diagonal image display from 26 inches (66 cm) or less to the screen

• The electronic pen and the projector can be used to convert your whiteboard into a virtual touchscreen. (WT615 only)

• Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white screen material (or a wall).

• USB memory or PC card interfaces provide for computer-free presentations.

• Enhanced smart security settings for password protection, cabinet control panel lock, menu lock and PC card protection key to help prevent unauthorized access, adjustments and theft deterrence.

• High resolution display - up to UXGA compatible, XGA native resolution.

•Variable audio out control of external amplified speakers via the projector remote.

• Extensive user adjustable picture and color management settings.

• Display 16:9 or 4:3 aspect ratio sources and fill the screen.

• HDTV (1080i, 720p) and SDTV (480p/576p, 480i/576i) compatibility.

• Digital photo viewer to display larger than life images from your digital cameras PC card, compact flash card or USB storage device.

• Wireless networking capable. Present from anywhere in the room when using as a wireless LAN projector, no physical signal cable connec-

tion to a PC is required. * The NEC optional wireless LAN card is required (NWL-100A or NWL-100E See page 25.).

• Supplied User Supportware 2 CD-ROM containing five software utilities allowing you to make the most of your NEC projector.

• Eco-mode lamp technology for increased lamp life, reduced energy consumption and overall total cost of ownership savings.

• Built-in laser pointer on the supplied remote control allows you to draw your audience's attention in a presentation.

Page 11

1. Introduction

About this user's manual

The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it.

• IBM is a trademark or registered trademark of International Business Machines Corporation.

• Mac, Macintosh and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

• Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks of Microsoft Corporation.

• Digital Light Processing and DLP are trademarks of Texas Instruments.

• Ulead is a trademark and/or registered trademark of Ulead Systems, Inc.

• eBeam and the eBeam logo are trademarks or registered trademarks of Luidia, Inc.

• Other product and company names mentioned in this user’s manual may be the trademarks or registered trademarks of their respective holders.

Page 12

 Part Names of the Projector

-A

-L

-V

I-I IN

I-I

1. Introduction

Front indicator Lights blue to indicate that the projector is turned on or in the Standby mode.

NOTE: When [Standby Mode]

L O

Mirror cover

Mirror cover lock switch

is set to “Power-saving”, this indicator lights blue only with power on.

Speaker

Ventilation (outlet)

Foot

Remote sensor

Foot

Lamp cover

Lamp cover screw

Built-in Security Slot ( )*

Speaker

Foot

* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of

Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.

Carrying handle

IRR

Sensor for Electronic pen

Controls

(WT615 only)

LAMP

STATUS

POWER

ON/

STAND BY

REFORM

EXIT

ADJUST

AUTO

ENTEER

SELECT

SOURCE

FOCUS

PC CARD

Te r minal panel

Ventilation (outlet)

Ventilation (inlet)

Main Power Switch

AC Input

Remote sensor

Page 13

Opening and Closing the Mirror Cover

1. Introduction

To open the mirror cover:

1. Slide the mirror cover lock switch to the unlock position.

U NL

K O R

L O

2. Slowly open the mirror cover holding both ends.

U N

O I R

K O R

L O

NOTE:

• Do not release your hold of the mirror cover until the mirror cover is fully open.

• Do not apply excessively strong pressure against the mirror cover or mirror surface while opening it.

• Keep finger prints off the mirror surface. Leaving finger prints in the mirror surface might cause an unwanted shadow and poor picture quality.

To close the mirror cover:

1. Slowly close the mirror cover while holding both ends.

CK R O R

NOTE:

• Do not release your hold of the mirror cover until the mirror cover is fully closed.

• Do not apply excessively strong pressure against the mirror cover or mirror surface while closing it.

• Keep finger prints off the mirror surface. Leaving finger prints in the mirror surface might cause an unwanted shadow and poor picture quality.

2. Slide the mirror cover lock switch to the lock position.

U N

L O

R L O

C K

NOTE:

• The projector cannot be turned on when the mirror cover is closed.

• Keep any items out of the light path or the mirror. Failure to do so may cause objects to catch on fire in unexpected places.

• The projector has a sensor which detects an object in front of the largest mirror or in the light path. If the sensor detects any object, the projector will not turn on. If this happens while the projector is turned on, the image is muted. In either case the STATUS indicator lights in red.

• The projector has a temperature sensor which detects heat. If the sensor detects excessive heat in the bottom of the mirror or in the light path, the projector will not turn on. If this happens while the projector is turned on, the projector will turn off (Standby mode). In either case the STATUS indicator flashes in red.

Page 14

1. Introduction

Top Features

FOCUS

PC CARD

SOURCE

1. POWER Button (ON / STAND BY)

Use this button to turn the power on and off when the main power is supplied and the projector is in standby mode.

NOTE: To turn on the projector, press and hold this button for a minimum of two seconds. To turn off the projector, press this button twice.

2. POWER Indicator ( )

When this indicator is green, the projector is on; when this indicator is orange, it is in standby mode. See the Power Indicator section on page 138 for more details.

3. STATUS Indicator

If this light blinks red rapidly, it indicates that an error has occurred, the lamp cover is not attached properly or the projector has overheated. If this light remains orange, it indicates that you have pressed a cabinet key while the Cabinet Button is locked. See the Status Indicator section on page 138 for more details.

4. LAMP Indicator

If this light blinks red rapidly, it's warning you that the projection lamp has exceeded 2000 hours (up to 4000 hours in Eco mode) of service. After this light appears, replace the lamp as soon as possible. (See page 134). If this is lit green continually, it indicates that the lamp mode is set to Eco. See the Lamp Indicator section on page 138 for more details.

SELECT

ENTER

AUTO

ADJUST

ON/

STAND BY

EXIT

REFORM

POWER

STATUS

LAMP

7 2

3 4

5. SOURCE Button

Use this button to select a video source such as a PC, VCR, DVD player or Viewer (PC card). Press and release this button quickly to display the Source List.

Each time this button is pressed for a minimum of ONE second, the input source will change as follows:

Computer → DVI (DIGITAL) → DVI (ANALOG) → Video → S-Video → Viewer → Computer → ...

If no input signal is present, the input will be skipped.

6. AUTO ADJUST Button

Use this button to adjust an RGB source for an optimal picture. See page 41.

7. 3D REFORM Button

Press this button to enter 3D Reform mode to correct the distortion, and make the image square. Each time this button is pressed, the item will change as follows: Pincushion → Cornerstone → Keystone → ... (the three items are available only when no adjustment is made)

8. FOCUS (+) (–) Buttons

Adjusts the focus.

9. MENU Button

Displays the menu.

10. SELECT 왖왔왗왘 (+) (–) / Volume Buttons

왖왔 : Use these buttons to select the menu of the

item you wish to adjust.

왗왘 : Use these buttons to change the level of a

selected menu item. When no menus appear, these buttons work as a volume control.

When the pointer is displayed, these 왖왔왗왘 buttons move the pointer.

11. ENTER Button

Executes your menu selection and activates items selected from the menu.

12. EXIT Button

Pressing this button will return to the previous menu with saving changes. While you are in the main menu, pressing this button will close the menu.

13. PC CARD Access Indicator

Lights while accessing a PC card.

Page 15

Te r minal Panel Features

1. Introduction

REMOTE

PCCONTROL

AUDIO IN

/MONO

VIDEO IN

PC CARD

S-VIDEO IN DVI-I IN

1. COMPUTER IN / Component Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equipment such as IBM compatible or Macintosh computers. Use the supplied RGB/VGA signal cable to connect to your computer. This also serves as a component input connector that allows you to connect a component video output of component equipment such as a DVD player. This connector also supports SCART output signal. See page 20 for more details.

2. COMPUTER AUDIO IN Mini Jack (Stereo Mini)

This is where you connect audio output from your computer or DVD player. A commercially available audio cable is required.

3. DVI-I IN Connector (DVI-I 29 Pin)

Connect a computer with a DVI output using a commercially available DVI-D cable. This connector can be used to accept digital and analog signal output from a computer with a DVI connector.

4. DVI-I AUDIO IN Mini Jack (Stereo Mini)

This is where you connect the audio output from your computer when connected to the DVI input. A commercially available audio cable is required.

5. MONITOR OUT Connector (Mini D-Sub 15 Pin)

You can use this connector to loop your computer image to an external monitor from the COMPUTER or the DVI-I input source. The RGB analog signal set on “OUT Terminal” is output during Standby mode. See pages 22 and 122.

12131514

USB

COMPUTER IN MONITOR OUT

3789

1 5

2410 11

AUDIO IN AUDIO OUT

DVI-I COMPUTER

6. AUDIO OUT Mini Jack (Stereo Mini)

Connect an additional audio equipment here to listen to audio coming from your COMPUTER, DVI-I, VIDEO or S-VIDEO input.

7. S-VIDEO IN Connector (Mini DIN 4 Pin)

Here is where you connect the S-Video input from an external source like a VCR.

NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format.

8. VIDEO IN Connector (RCA)

Connect a VCR, DVD player, laser disc player, or document camera here to project video.

9. VIDEO AUDIO IN Jacks (RCA)

L: This is your left channel audio input for stereo

sound coming from the VIDEO source.

R: This is your right channel audio input for stereo

sound from the VIDEO source.

10. REMOTE IN Jack (Mini Jack)

Connect your remote control cable here for wired operation.

11. PC CONTROL Port (Mini DIN 8 Pin)

Use this port to connect your PC or control system to control your projector via a serial cable. This enables you to control the projector using serial communication protocol. An optional serial cable (CA03D: 9Pin D-Sub to 8 Pin Mini DIN) is required for this port. You can also control the projector by using PC Control Utility 3.0 contained on the supplied User Supportware 2 CD-ROM. To do so you must first have PC Control Utility 3.0 installed on your PC. If you are writing your own program, typical PC control codes are on page 147.

Page 16

Te r minal Panel Features

1. Introduction

REMOTE

PCCONTROL

AUDIO IN

/MONO

VIDEO IN

PC CARD

S-VIDEO IN DVI-I IN

12. USB Port (Type B)

Connect this port to the USB port (type A) of your PC using the supplied USB cable. You can operate your computer's mouse functions from the remote control.

13. USB Port (Type A)

Connect a commercially available USB memory device or mouse that supports USB. You can operate the menu or Viewer with the USB mouse via this port. Note that this port should not be connected to a computer and that there may be some brands of USB mouse that the projector does not support.

12131514

USB

COMPUTER IN MONITOR OUT

3789

14. PC CARD Slot

15. PC CARD Eject Button

1 5

Insert a PC card, commercially available LAN card or NEC optional wireless LAN card here.

NOTE: A dummy card is inserted into each slot at the time of shipment. First remove the dummy cards before use.

Press to eject a PC card partially.

2410 11

AUDIO IN AUDIO OUT

DVI-I COMPUTER

Page 17

쐏 Part Names of the Remote Control

1. Introduction

10 11

6. MAGNIFY (+) (–) Buttons

Use these buttons to adjust the image size. The image can be magnified about the center of the screen up to 400%. See page 52.

OFF

MAGNIFY

VIDEO

ASPECT

PIC-MUTE

VOLUME

FREEZE

COMPUTER

POWER

LASER

POINTER

AUTO ADJ.

HELP

PAGE

DOWN

VIEWER

SLIDE

ZOOMFOCUS

3D REFORM

7. LASER Button

Press and hold this button to activate the laser pointer. When lit, you can use the laser to draw your audience's attention to a red dot that you can place on any object. See page 44.

8. POINTER Button

Press this button to display the projector pointer. You can move your pointer icon to the area you want on the screen using the SELECT 왖왔왗 or 왘 button. See page 51.

9. PAGE (UP) (DOWN) Buttons

Use these buttons to scroll the viewing area of the window or to move to the previous or next slide in PowerPoint on your computer when the supplied USB cable is connected with your computer.

10. MENU Button

Displays the menu for various settings and adjustments.

1. Infrared Transmitter/Laser Pointer

Tr ansmits an infrared signal when any button other than LASER is pressed. Direct the remote control toward the remote sensor on the projector cabinet. Beams a laser light when the Laser button is pressed.

CAUTION:

* Do not look into the laser pointer while it is on. * Do not point the laser beam at a person.

2. Remote Jack

Connect your remote control cable here for wired operation.

3. LED

Flashes when any button is pressed.

4. POWER ON Button

When the main power is on, you can use this button to turn your projector on.

NOTE: To turn on the projector, press and hold the POWER ON button for a minimum of two seconds.

5. POWER OFF Button

You can use this button to turn your projector off.

NOTE: To turn off the projector, press the POWER OFF button twice.

11. SELECT 왖왔왗왘 Button

This button is used for projector’s menu operation and moving the magnified image. This button also works as a computer mouse when the supplied USB cable is connected with your computer.

12. ENTER Button

Executes your menu selection and activates items selected from the menu.

13. EXIT Button

Returns to the previous menu. While you are in the main menu, pressing this button will close the menu.

14. R-CLICK Button

Works as the mouse right button when the supplied USB cable is connected with your computer.

Page 18

1. Introduction

15. L-CLICK Button

Works as the mouse left button when the supplied USB cable is connected with your computer.

16 21

22 23

OFF

MAGNIFY

VIDEO

ASPECT

PIC-MUTE

VOLUME

FREEZE

COMPUTER

POWER

LASER

POINTER

AUTO ADJ.

HELP

PAGE

DOWN

VIEWER

SLIDE

ZOOMFOCUS

3D REFORM

19 18

20. SLIDE (+) (–) Buttons

Press (+) to select the next folder or slide and press (–) to select the previous folder or slide.

21. ASPECT Button

Press this button to display the Aspect Ratio select menu. See page 90.

22. PIC-MUTE Button

This button turns off the image and sound for a short period of time. Press again to restore the image and sound. See page 51.

23. HELP Button

Provides the online help. See page 52.

24. VOLUME (+) (–) Buttons

Press (+) to increase the volume and (–) to decrease it. See page 41.

25. FOCUS (+) (–) Buttons

Adjust the focus.

26. ZOOM (+) (–) Buttons

Reduces the image size between 80% and 100%.

27. FREEZE Button

This button will freeze a picture. Press again to resume motion. See page 51.

28. 3D REFORM Button

Press this button to enter 3D Reform to correct the pincushion, the cornerstone or the keystone distortion, and make the image square. See pages 42 and

99 - 102.

16. VIDEO Button

Press this button to toggle between Video and S-Video inputs.

17. COMPUTER Button

Press this button to select the COMPUTER, DVI (DIGITAL) or DVI (ANALOG) input.

18. AUTO ADJ. Button

Use this button to adjust an RGB source (COMPUTER) for an optimal picture. See page 41.

19. VIEWER Button

Press this button to select the Viewer source. See page

71.

Page 19

Battery Installation

1. Introduction

Remove the battery cover.

NOTE: Do not pull the battery cover by force. Doing so can result in its complete removal.

Remove both old batteries and install new ones (AAA). Ensure that you have the batteries' polarity (+/ –) aligned correctly.

Slip the cover back over the batteries until it snaps into place.

NOTE: Do not mix different types of batteries or new and old batteries.

Operating Range for Wireless Remote Control

7m/22 feet

Remote control

7m/22 feet

30°

Remote control

• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of

the remote sensor on the projector cabinet.

• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls

on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.

Remote sensor on the projector cabinet

30°

Remote Control Precautions

• Handle the remote control carefully.

• If the remote control gets wet, wipe it dry immediately.

•Avoid excessive heat and humidity.

• If you will not be using the remote control for a long time, remove the batteries.

• Do not place the batteries upside down.

• Do not use new and old batteries together, or use different types of batteries together.

• Dispose of used batteries according to your local regulations.

Using the Remote Control in Wired Operation

Connect one end of the supplied remote cable to the REMOTE mini jack and the other end to the remote jack on the remote control.

REMOTE

PCCONTROL

PC CARD

REMOTE

S-VIDEO IN DVI-I IN

AUDIO IN

VIDEO IN

/MONO

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

NOTE: Inserting the remote cable into the REMOTE IN jack will automatically change the projector’s Standby mode to Normal mode even if Power-saving mode has been selected.

Page 20

1. Introduction



Part Names and Functions of the Supplied Electronic Pen (WT615 only)

The WT615 comes with an electronic pen. The electronic pen works as a USB mouse connected to the projector. See page 53 for connecting a USB mouse. The electronic pen and the projector’s sensors can be used to convert your whiteboard into a virtual touchscreen which allows you to operate your projector’s menu or use the ChalkBoard feature. See “ Using the Electronic Pen” on page 45.

Important

Before you use the electronic pen or when you have changed the position of the projector or the screen size, be sure to use [Calibration] to calibrate the electronic pen and the screen.

Button B

Pen tip

Button A

The buttons work as computer mouse buttons.

Pen tip ................... Left click button

Button A ................ Right-click button

Button B ................ Button to turn on or off the ChalkBoard toolbar.

NOTE:

• Button A or B must be pressed and held for a minimum of 0.5 second.

• Pressing and holding the buttons A and B at the same time for a minimum of 0.5 second will change to “Pen Calibration”

mode. See also page 47.

Requirements for the Electronic Pen Function

• Screen size: 40” to 80”

• Projector orientation: “Desktop Front” and “Ceiling Front”

• [Screen Type]: “4:3”

• [Aspect Ratio]: “4:3”

• Digital Zoom: 100%

• [Cornerstone] and [Keystone]: Not performed

• Operating temperature: 59 to 95°F (15 to 35°C)

• [Resolution]: "Auto"

NOTE: Do not hold this part. Otherwise, the electronic pen may not work properly.

Battery Installation

123

Electronic Pen Precautions

• Handle the electronic pen carefully.

• If the electronic pen gets wet, wipe it dry immediately.

•Avoid excessive heat and humidity.

• If you will not be using the electronic pen for a long time, remove the battery.

• Dispose of a used battery according to your local regulations.

Page 21

Installation and Connections

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 Setting Up the Screen and the Projector ................... 16

 Making Connections .................................................. 19

When Viewing a DVI Digital Signal ....................................................................... 19

Connecting Your PC or Macintosh Computer ....................................................... 19

To connect SCART output (RGB)......................................................................... 20

Using two Analog COMPUTER inputs simultaneously ........................................ 21

Connecting an External Monitor ........................................................................... 22

Connecting Your DVD Player ................................................................................ 23

Connecting Your VCR or Laser Disc Player .......................................................... 24

Connecting to a Network ...................................................................................... 25

Inserting and Removing a PC Card ...................................................................... 27

Connecting the Supplied Power Cable ................................................................. 29

Page 22

2. Installation and Connections

This section describes how to set up your projector and how to connect video and audio sources.

When installing the projector for the first time, read the WT615/WT610 Setup Guide carefully.

Your projector is simple to set up and use. But before you get started you must first:

1. Set up a screen and the projector.

NOTE: Using a warped screen can cause an image to appear distorted.

2. Connect your computer or video equipment to the projector. See page 19 to 28.

NOTE: To connect a network, see page 25.

3. Connect the supplied power cable. See page 29.

NOTE: Ensure that the power cable and any other cables are disconnected before moving the projector. When moving the projector or when it is not in use, close the mirror cover on the top cabinet.

Page 23

2. Installation and Connections

 Setting Up the Screen and the Projector

1. Refer to "Throw Distance (C)" in the diagram and use a distance between the screen and projector that corresponds to the screen size.

As an example, when projecting to a 60" screen, set the projector with a separation of approximately 10.4"/26.3 cm from the screen.

2. Refer to "Height (D)" below and adjust the screen height, or adjust the height of the projector stand. As an example, when projecting to a 60" screen, adjust the height from the feet of the projector to the lower

edge of the screen to approximately 19.0"/48.2 cm.

Screen size

(inch)

40 45 50 55 60 65 67 70 72 75 78 80 84 85 90 95 96

100

Height (B)

mm inch

659 729 799 869

939 1010 1037 1080 1107 1149 1191 1219 1275 1289 1359 1428 1443 1499

25.9

28.7

31.5

34.2

37.0

39.7

40.8

42.5

43.6

45.2

46.9

48.0

50.2

50.7

53.5

56.2

56.8

59.0

Throw distance (C)

mm inch

64 114 164 214 263 313 332 362 381 412 441 461 500 510 559 609 619 659

Screen center

Back of projector

Projector foot

NOTE

• There is a tolerance of +/–5% because of design values.

• The projection distance and the lower edge of the screen are calculated using a 4:3 aspect ratio.

Height (D)

2.5

4.5

6.4

8.4

10.4

12.3

13.1

14.3

15.0

16.2

17.4

18.1

19.7

20.1

22.0

24.0

24.4

25.9

120

100

Screen size (inch)

mm inch

354 386 418 450 482 514 526 546 558 577 596 609 635 641 673 704 711 737

0 100 200 300 400 500 600 700

13.9

15.2

16.5

17.7

19.0

20.2

20.7

21.5

22.0

22.7

23.5

24.0

25.0

25.2

26.5

27.7

28.0

29.0

Throw distance C (mm)

120

100

Screen size (inch)

051015 20 25 30

Throw distance C (inch)

Page 24

2. Installation and Connections

Screens Suited

• The projector can accommdate screen sizes from 40” (81.3 cm/32.0” W ⳯ 61.0 cm/24.0” H) to 100 inch (203.2 cm/80.0” W ⳯ 152.4 cm/60.0” H).

40"-100"

• Use a panel or tension type screen that has a flat surface.

Recommended

Do not use roll type screens and other screens that bend or form a wavy surface easily. Doing so will result in increased distortion of the projected image.

• View the screen directly from the side so that it is perfectly vertical.

Recommended

A slanted screen will result in increased keystone distortion.

90˚

• In using this projector, increasing the screen size will move the projection position upward. To accommodate this, please use a screen that can be raised and lowered to a given screen position. See page 16 for information about the positioning relationships between the screen and this projector.

• High gain type screens are not optimal for use with this projector. The lower the screen gain (i.e., screen gain on the order of 1), the better the appearance of the projected image. For more information about screen gain, consult catalogs from screen manufacturers.

• Screen frames or pen shelves that protrude from the front of the screen surface may block some of the light from the projector.

• Due to the projection angle of the projector, many standard rear projection screens may produce uneven brightness, hot spotting or not produce maximum brightness to the viewer. For more details utilizing rear projection screens and their applications with this projector, please contact your NEC dealer.

Not recommended

Recommended

Not recommended

Not optimal

• Controlled ambient light environments will allow for an image of higher contrast and depth to be displayed.

• Screens with a soiled, scratched, or discolored area will not produce a clean image. Care should be used in the handling of the screen.

Stands Suited

• In using this projector, increasing the screen size will move the projection position upward. To accommodate this, please use a stand that has a height positioning adjustment. See page 16 for information about the positioning relationships between the screen and this projector.

• Use a stand that will allow this projector to be set up in a level condition. Adjust the feet of the stand to make sure it is level.

Not recommended

Recommended

Level

Page 25

2. Installation and Connections

Ambient environmental condition

• Do not place the screen near vents. Air movement hitting the screen, causing the projected image to ripple.

• Do not illuminate the projector with strong light sources such as halogen lamp. Doing so can cause the object detection sensor to malfunction, resulting in the projector not turning on.

Precautions for using the electronic pen (WT615 only)

• Use a hard-surface screen because you tap the screen using the electronic pen. Supported screen sizes are 40 to 80" (101.6 to 203.2 cm).

•Keep in mind that the electronic pen tip can cause scratches on the screen surface as the pen tip is made of hard material.

• Do not use the electronic pen under the following conditions. Otherwise, the electronic pen may not work properly.

- Near a device such as a CRT monitor or a TV set.

- In a room with the ceiling and walls made of metal which is prone to reflect sound waves.

- In a noisy place or a place where loud sounds can be heard

- In direct sunlight or near an inverter fluorescent lamp.

- Near an air conditioner or air blower

• Do not hold any part ahead of the black ring part of the electronic pen. Otherwise, the electronic pen may not work properly.

• Do not use two or more electronic pens and projectors at the same time in the same room. Be sure to use the electronic pen and the projector on a one-to-one basis.

• Operational temperature for electronic pen is 59° to 95°F (15° to 35°C).

Page 26

2. Installation and Connections

 Making Connections

NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from the RGB output unless the notebook PC is turned on after connecting with the projector.

* If the screen goes blank while using your notebook PC, it may be the result of the computer's screen-saver or power manage-

ment software.

When Viewing a DVI Digital Signal

To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before turning on your PC or projector. Turn on the projector first and select DVI (DIGITAL) from the source menu before turning on your PC. Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC. Do not disconnect the DVI cable while the projector is running. If the signal cable has been disconnected and then reconnected, an image may not be correctly displayed. Should this happen, restart your PC.

NOTE:

• Use a DVI cable or the one compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard. The DVI cable should be within 5 m (196") long. Both single and dual types of DVI cable can be used.

• The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @ up to 60Hz).

Connecting Your PC or Macintosh Computer

IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)

DVI cable (not supplied)

PHONE

COMPUTER IN

PCCONTROL

REMOTE

DVI-I IN

VIDEO IN

AUDIO IN

/MONO

PC CARD

S-VIDEO IN DVI-I IN

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

Audio cable (not supplied)

AUDIO IN DVI-I

AUDIO IN COMPUTER

Audio cable (not supplied)

RGB/VGA signal cable (supplied) To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribution amplifier if connecting a signal cable longer than the one supplied.

PHONE

IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type)

NOTE: For older Macintosh, use a commercially available pin adapter (not supplied) to connect to your Mac's video port.

NOTE: The WT615/WT610 is not compatible with video decoded outputs of either the NEC ISS-6020 or ISS-6010.

Page 27

2. Installation and Connections

To connect SCART output (RGB)

Before connecting: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are required for this connection.

NOTE: Audio signal is not available for this connection.

Video equipment such as DVD player

Projector

PCCONTROL

REMOTE

PC CARD

S-VIDEO IN DVI-I IN

AUDIO IN

VIDEO IN

/MONO

COMPUTER IN

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

To COMPUTER IN

Commercially available SCART cable

Female

ADP-SC1

1. Turn off the power to the projector and your video equipment.

2. Use the NEC ADP-SC1 SCART adapter and a commercially available SCART cable to connect the COMPUTER input of your projector and a SCART output (RGB) of your video equipment.

3. Turn on the power to the projector and your video equipment.

4. Use the COMPUTER button on the remote control to select the COMPUTER input.

5. Press the MENU button on the remote control to display the menu.

6. From the Advanced menu, select [Setup]

→

[Options] → [Signal Select] → [Computer] → [Scart].

SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-connector.

NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe. Contact your NEC dealer in Europe for more information.

Page 28

2. Installation and Connections

Using two Analog COMPUTER inputs simultaneously

If you need to use two analog COMPUTER inputs simultaneously, connect a DVI-A to VGA cable as shown below.

IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)

DVI-I IN

PCCONTROL

REMOTE

AUDIO IN

/MONO

DVI-A to VGA cable (not supplied)

VIDEO IN

PC CARD

S-VIDEO IN DVI-I IN

COMPUTER IN

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

RGB/VGA signal cable (supplied)

IBM PC or Compatibles (Notebook type) or Macintosh (Notebook type)

Page 29

Connecting an External Monitor

2. Installation and Connections

PCCONTROL

PC CARD

REMOTE

S-VIDEO IN DVI-I IN

AUDIO IN

VIDEO IN

/MONO

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

MONITOR OUT

RGB/VGA signal cable (commercially available or supplied with an external monitor)

You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog image you're projecting. To do so:

1. Turn off the power to your projector, monitor and computer.

2. Use a 15-pin cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on your projector.

3. Turn on the projector, monitor and the computer.

NOTE:

• When the projector is in the Standby mode, the image may not be correctly displayed while the cooling fans are running

immediately after turning on or off the power. Note that the MONITOR OUT connector will not output an RGB signal during Power-saving mode (See page 119 for enabling the Power-saving mode).

• Daisy chain connection is not possible.

Page 30

Connecting Your DVD Player

2. Installation and Connections

Optional 15-pin-to-RCA (female)

⳯

3 cable (ADP-CV1)

Component video RCA (not supplied)

Audio Equipment

AUDIO IN

COMPUTER IN

⳯

3 cable

AUDIO IN COMPUTER

PCCONTROL

PC CARD

REMOTE

S-VIDEO IN DVI-I IN

AUDIO IN

VIDEO IN

/MONO

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

Audio cable (not supplied)

DVD player

YCbCr

Component

L R

AUDIO OUT

Audio cable (not supplied)

You can connect your projector to a DVD player with component output or Video output. To do so, simply:

1. Turn off the power to your projector and DVD player.

2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable (RCA⳯3) and the optional 15-pin-to-RCA (female)⳯3 cable to connect your DVD player to the COMPUTER IN connector on the projector.

For a DVD player without component video (Y,Cb,Cr) output, use an S-Video cable (not provided) to connect the S-Video output of the DVD player to the S-Video Input of the projector.

3. Turn on the projector and DVD player.

NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.

NOTE: Normally switching between RGB and component signals will be performed automatically, but if it fails, from the menu select [Setup] → [Options] → [Signal Select] → [Component] for the RGB signal.

Page 31

Connecting Your VCR or Laser Disc Player

2. Installation and Connections

Audio cable (not supplied)

VCR/ Laser disc player

VIDEO IN

AUDIO IN

L R

AUDIO OUT

PCCONTROL

REMOTE

VIDEO IN

AUDIO IN

/MONO

VIDEO OUT

S-VIDEO IN

PC CARD

S-VIDEO IN DVI-I IN

S-VIDEOVIDEO

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

Video cable (not supplied)

S-video cable (not supplied)

Audio equipment

AUDIO IN

Audio cable (not supplied)

Use common RCA cables (not provided) to connect your VCR, laser disc player or document camera to your projector. To make these connections, simply:

1. Turn off the power to the projector and VCR, laser disc player or document camera.

2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your projector. Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio equipment (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.

3. Turn on the projector and the VCR or laser disc player.

NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements.

NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via a scan converter.

Page 32

2. Installation and Connections

Connecting to a Network

The WT615/WT610 comes standard with a PC Card slot which accepts a wired and wireless LAN card. Placing the optional wireless LAN card (NWL-100A/E) in the PC card slot of the projector provides a wireless LAN connection. To use a LAN connection, you are required to assign an IP address to the projector. For setting the LAN mode, see page

111 (From the menu, select [Setup] → [Installation] → [LAN Mode]).

*Two optional wireless LAN cards (NWL-100A and NWL-100E) are available. For a list of countries where

NEC's optional wireless LAN card (NWL-100 series) is available, refer to the Service Page for NEC Projectors (http://www.nec-pj.com).

*For more information on supported wired LAN cards for the NEC projectors, refer to the Service Page for

NEC Projectors (http://www.nec-pj.com).

With the LAN connection, two features are available: Projector control and Picture transmission.

Projector control feature

With the wired or wireless LAN connection, you can control (power on/off, input select, etc.) and receive information from the projector over the network using a computer. The following two methods are available:

* Using the HTTP Server feature on the projector. See page 63. * Using PC Control Utility 3.0 from the supplied User Supportware 2 CD-ROM.

Picture transmission feature

With the wired or wireless LAN connection, you can send images and slides from a personal computer to the projector which then can be projected on the screen. The following two methods are available:

* Using Image Express Utility 2.0 from the supplied User Supportware 2 CD-ROM. * Using Ulead Photo Explore 8.0 from the supplied User Supportware 2 CD-ROM.

With the USB mouse connected to the projector, you can also operate the desktop screen on your Windows PC connected to the LAN or the wireless LAN.

* Using Desktop Control Utility 1.0 from the supplied User Supportware 2 CD-ROM.

NOTE: Use a Wi-Fi certified wireless LAN card for your PC.

NOTE: For information about the five software utilities (Image Express Utility 2.0, Desktop Control Utility 1.0, Ulead Photo Explorer 8.0, Viewer PPT Converter and PC Control Utility 3.0) contained on the supplied Projector User Supportware 2.0 CDROM, see the supplied “Wired and Wireless Network Setup Guide”. See also each online help of the software utilities for information about their functions and operations.

Example of LAN connection

(A) Example of wired LAN connection

Wired LAN card (not supplied)

Server

PCCONTROL

REMOTE

AUDIO IN

/MONO

Hub

S-VIDEO IN DVI-I IN

VIDEO IN

LAN cable (not supplied)

PC CARD

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

Page 33

(B) Example of wireless LAN connection (Network Type → Mode: Infrastructure)

Wireless LAN card (optional)

2. Installation and Connections

Wireless LAN card Built-in wireless LAN function

Access Point

Wired LAN

To make connection with a wired LAN via an access point, you need to select the Infrastructure mode. From the menu, select [Setup] → [Installation] → [LAN Mode] → “Profile” → “Advanced” → “Network Type” →“Mode” → “Infrastructure”.

Wireless LAN card (optional)

Wireless LAN card

Built-in wireless LAN function

To enable direct communication (i.e., peer-to-peer) between personal computers and projectors, you need to select the 802.11 Ad Hoc mode. From the menu, select [Setup] → [Installation] → [LAN Mode] → “Profile” → “Advanced” → “Network Type” → “Mode” → “802.11 Ad Hoc”.

The 802.11 Ad hoc mode complies with IEEE802.11 standard.

When in Ad Hoc mode, only 802.11b is available for communication method. Data transmission speed in Ad Hoc mode is limited up to 11Mbps.

Page 34

2. Installation and Connections

DIO

VID

S-VID

VI-I IN

ITO

I-I

IO IN

CCO

PC CARD

AUDIO IN

/MONO

VIDEO IN

S-VIDEO IN

DVI-I IN

COMPUTER IN

MONITOR OUT

DVI-I RGB

AUDIO IN

USB

AUDIO OUT

PCCONTROL

REMOTE

Inserting and Removing a PC Card

To insert the NEC optional wireless LAN card or a PC memory card (also referred to as PC card in this manual), follow the steps below.

CAUTION:

* Direction for Inserting the PC Card

The PC card has a top and bottom and must be inserted into the PC card slot in a specific direction. It cannot be inserted backwards or upside-down.

Attempting to force it into the slot in the wrong direction may break the internal pin and damage the card

slot. Refer to the PC card's operating instructions for the proper direction of insertion. * Back up your PC card's data in case it will need to be restored. *To prevent electrostatic discharge damage to the wireless LAN card, wear an anti-static wrist strap. If no

wrist strap is available, ground yourself by touching metal such as a door knob.

Inserting the PC Card

1. Turn off the main power switch before inserting the PC card. (This step is needed only when the LAN card being inserted into the projector's PC CARD slot)

2. Hold the PC card horizontally and insert it slowly into the PC card slot with its top facing up.

PC card (not supplied)

The eject button pops out once the PC card is fully inserted. Check that the PC card is fully inserted.

NOTE: Do not try to force the PC card into the slot or you may bend the pins inside the slot.

Removing the PC Card

1. Make sure that the PC CARD access indicator is not lit. (This step is needed only when the PC memory card being inserted into the projector’s PC CARD slot.)

NOTE: The PC CARD access indicator lights while its data is being accessed.

2. To remove the LAN card, turn off the main power. (This step is needed only when the LAN card being inserted into the projector's PC CARD slot)

3. Press the eject button. The PC card pops out a little. Grasp the edges of the PC card and pull it out.

Eject button

PC CARD

SOURCE

FOCUS

SELECT

EXIT

3D REFORM

ENTER

POW

AUTO

STATUS

ADJUST

LAMP

N/ O STAND BY

PC CARD

SOURCE

FOCUS

SELECT

EXIT

3D REFORM

ENTER

POWER

AUTO

STATUS

ADJUST

LAMP ON/ STAND BY

Page 35

2. Installation and Connections

PC Card Type

The PC Card slot accepts PCMCIA Type II only.

NOTE: The projector does not support NTFS formatted flash memory card. Be sure to use a flash memory card formatted with the FAT32, FAT16 or FAT file system. To format your flash memory card in your computer, refer to the document or help file that comes with your Windows operating systems.

Page 36

2. Installation and Connections

P C

D I O

I N

O N

E O

I N

I D

I N

D V

- I

I N

O M

U T

I N

N I

O R

U T

D V

C O

M P

T E

A U

I O I

U S

A U

I O

U T

C O

N T

O L

E M

E I N

Connecting the Supplied Power Cable

Connect the supplied power cable to the projector. First connect the supplied power cable's three-pin plug to the AC IN of the projector, and then connect the other plug of the supplied power cable in the wall outlet.

K C

O L N

R O

O L

Make sure that the prongs are fully inserted into both the AC IN and the wall outlet.

←

To wall outlet

CAUTION: Do not unplug the power cable from the wall outlet under any one of the following circumstances. Doing so can cause damage to the projector or PC card:

• While the projector's lamp is On.

• While the cooling fans are running. The cooling fans continue to work for 90 seconds after the projector is turned off.

• While the PC CARD Access Indicator lights. Doing so can damage your PC memory card.

D R A

C C P

E C R U

S C O

U N E M

C E L

E S

I X E

U A

M A L

D N

A T S

Page 37

Projecting an Image

(Basic Operation)

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 Tu rning on the Projector............................................. 31

 Adjusting the Position and Size of the Projected Image

(Focus Adjustments) .............................................. 33

 Selecting a Source .................................................... 40

쐏 Optimizing an RGB Image Automatically................... 41

 Tu rning Up or Down Volume ...................................... 41

 Adjusting Pincushion or Barrel Distortion

(Pincushion)........................................................... 42

 Using the Laser Pointer ............................................. 44

 Using the Electronic Pen (WT615 only) ..................... 45

 Tu rning off the Projector............................................. 48

쐅 After Use.................................................................... 49

Page 38

3. Projecting an Image (Basic Operation)

This section describes how to turn on the projector and to project a picture onto the screen.

 Turning on the Projector

NOTE:

• The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button (POWER ON and OFF on the remote control).

䡬

• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off ( position. Failure to do so may cause damage to the projector.

• The projector has a feature to prevent itself from being used by unauthorized individuals. To use this feature, register a keyword. See "Security" in "Setup" on page 57 for more details.

1. Open the mirror cover. See page 6 for more details.

)

2. To turn on the main power to the projector, press the

Main Power switch to the on position ( I ).

• The POWER indicator will light orange.

See the Power Indicator section on page 138 for more details.

3. Press the POWER (ON/STAND BY) button on the

projector cabinet or POWER ON button on the remote control for a minimum of 2 seconds, when the PWOER indicator turns a steady green the projector is ready to use.

• After you turn on your projector, ensure that the

computer or video source is turned on.

NOTE: If you turn on the projector immediately after the lamp is turned off or when the temperature is high, the fans run without displaying an image for some time and then the projector will display the image.

Cabinet controls Remote control

ENTER EXIT

REFORM

AUTO

ADJUST

POWER

ON/

STATUS

STAND BY

LAMP

Standby

Blinking for one minute

LAMP

STATUS

POWER

ON/

STAND BY

Steady orange

Blinking green

light

Press this button for a

minimum of 2 seconds.

POWER

STATUS

LAMP

OFF

POWER

LASER

PAGE

MAGNIFY

POINTER

DOWN

Power On

LAMP

STATUS

POWER POWER

LAMP

STATUS

Steady green

light

See page 138 for more details.

NOTE: When no signal is available, a blue, black or logo screen is displayed.

Page 39

3. Projecting an Image (Basic Operation)

Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 21 menu languages.

To select a menu language, follow these steps:

1. Use the SELECT 왖 or 왔 button to select one of the

21 languages for the menu.

2. Press the ENTER button to execute the selection.

The menu will be displayed in the language you have selected.

3. To close the menu, press the EXIT button.

After this has been done, you can proceed to the menu operation. If you want, you can select the menu language later. See "Language" on page 103.

Cabinet controls Remote control

OFF

SELECT

ENTER EXIT

AUTO

ADJUST

ON/

STAND BY

SELECT

ENTER

AUTO

ADJUST

ON/

STAND BY

SELECT

ENTER

AUTO

ADJUST

ON/

STAND BY

REFORM

POWER

STATUS

LAMP

POWER

STATUS

LAMP

EXIT

POWER

STATUS

LAMP

EXIT

MAGNIFY

OFF

MAGNIFY

POWER

LASER

PAGE

POINTER

DOWN

POWER

LASER

POINTER

POWER

LASER

POINTER

PAGE

DOWN

PAGE

DOWN

OFF

NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.

• When the Lamp mode is set to Eco, the Lamp indicator will light green.

• If one of the following things happens, the projector will not turn on.

- If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this

condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down.

- When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp. See

page 134.

- If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and

then turn on the power.

- When the mirror cover is closed.

- If the temperature sensor detects excessive heat in the bottom of the mirror or in the light path, the projector will

not turn on. Remove objects such as dust from the bottom of the mirror.

- The projector has a sensor which detects an object in front of the largest mirror or in the light path. If the sensor

detects any object, the projector will not turn on. Remove the object.

- Do not illuminate the projector with strong light source such as halogen lamp.

Doing so can cause the object detection sensor to malfunction, resulting in the projector not turning on.

• Immediately after turning on the projector and displaying an image, you cannot turn off the projector for 60 seconds.

Page 40

3. Projecting an Image (Basic Operation)

90˚

 Adjusting the Position and Size of the Projected Image (Focus Adjustments)

• After turning on the power, projected images may flicker for 3 to 5 minutes until the lamp lighting is stabilized.

Also after turning on the projector, the picture position may be slightly changed. Wait 10 minutes until the light status and projected images become stable.

• If the screen is tilted vertically or horizontally, keystone distortion becomes large. Proceed with the following

steps to correctly set up the projector and the screen.

Operations common to both WT615 and WT610

1. Check whether the screen is set up to be vertical by viewing it from

the side.

2. Check that the projector is set to be parallel with the screen.

Top view

Screen surface

Parallel

Align the projector center with the screen center

Side view

°

Bottom of projector

Screen surface



Page 41

3. Projecting an Image (Basic Operation)

3. Press the MENU button.

The menu will be displayed.

4. Press the FOCUS +/- buttons and align the focus of the projected

image.

Cabinet controls

PC CARD

FOCUS

SOURCE

SELECT

Remote control

VIDEO

VIEWER

COMPUTER

AUTO ADJ.

SLIDE

ASPECT

HELP

PIC-MUTE

FOCUS

ZOOM

VOLUME

3D REFORM

FREEZE

5. Use the SELECT 왘 button to select [Setup] and then press the ENTER button.

6. Use the SELECT 왖 or 왔 button to select [Tilt Indicator] and then press the ENTER button.

The test pattern will be displayed to fill the screen. At the same time the [Tilt Indicator] screen will be displayed at the bottom of the screen.

WT615 WT610

Page 42

3. Projecting an Image (Basic Operation)

7. Adjust the height to keep the projector level by rotating the

feet on the front and the rear.

Tilting the projector will move the Tilt Indicator’s slider to the left or right accordingly. Tilt the projector so that both of the sliders of “Back/Front” and “Left/Right” are shown at the center. When the slider reaches the center, it will become green.

8. Press the FOCUS +/– buttons to align the focus of the projected

image.

A press of the FOCUS +/– buttons results in focus being taken simultaneously with the adjustment of vertical keystone distortion. See page 102.

Cabinet controls

PC CARD

FOCUS

SOURCE

SELECT

Remote control

VIDEO

VIEWER

COMPUTER

AUTO ADJ.

SLIDE

ASPECT

HELP

PIC-MUTE

FOCUS

ZOOM

VOLUME

3D REFORM

FREEZE

9. Move the projector away from or closer to the screen and position it

so that the left and right sides of the projected image are aligned with the width of the screen.

Down

10. Adjust the height of the screen and the height of the stand to align

the lower edge of the projected image with the lower edge of the screen.

Page 43

3. Projecting an Image (Basic Operation)

11. Press the FOCUS +/– buttons to align the focus of the projected

image again.

• Repeat step 9 to 11 if the display image is not aligned with the screen.

• On the WT615 you can use the electronic pen to help you set up the projector parallel to the screen. For more information, see "Setting up the projector parallel to the screen" below.

12. To complete the adjustment, press the EXIT button three times.

The menu will disappear.

Setting up the projector parallel to the screen (WT615 only)

You can use the electronic pen to adjust so that the projector and the screen are parallel to each other.

1. Press the ENTER button while the [Tilt Indicator] screen is being displayed.

A mark will be shown on the screen with a message: Tap the center of a mark with the electronic pen. To cancel, press the button A.

2. Touch the center of a mark lightly with the electronic pen until the mark disappears.

NOTE: Hold the electronic pen upright against the screen when using it. Otherwise, the actual pen stroke may not be reflected on the screen.

Another mark will be shown with a message: Tap the center of a mark with the electronic pen. To cancel, press the button A.

Touch

Page 44

3. Projecting an Image (Basic Operation)

3. Touch the center of the mark lightly with the electronic pen.

Touch

The [Parallel Detect] screen will be displayed.

When the marker is in the center of the gauge, go to Step 6. When the marker is not in the center of the gauge, it means that the projector and the screen are not parallel to

each other. Go to Step 4.

4. Rotate the projector right or left so that the projector is parallel to the screen.

Screen Screen

Top view

[The marker is on the left side] [The marker is on the right side] Rotate the projector right. Rotate the projector left.

5. Touch the [Retry] button with the electronic pen.

Repeat Steps 2 to 4.

6. When the marker reaches the center of the gauge, press the button "A" on the electronic pen.

The [Tilt Indicator] screen will be displayed again.

Button “A”

7. Press the EXIT button three times.

The menu will be closed.

Page 45

R-AUDIO IN-L/MONO

-V

I-

I IN

I-I

3. Projecting an Image (Basic Operation)

NOTE:

• In terms of the optical characteristics of this projector, in addition to keystone distortion (page 102), there may be occurrences

of slight pincushion type or barrel type distortion. To adjust the projected image with the screen, first perform Steps 9 to 11 on pages 35 to 36 (Adjustment of the projection

→

distance with the 4 corners of the screen. Following this, if the pincushion type or the barrel type distortion is conspicuous, please perform "

• If the keystone distortion is not improved after pressing the FOCUS +/– buttons and adjusting the focus, or the aspect ratio

does not agree, make sure the screen or projector are not tilted.

[Symptom1] In the case of keystone distortion (as illustrated), either the screen is directed slightly upward or the projector is directed slightly upward.

[Action] Tilt the top end of the screen to the front or rotate the front feet of the projector to correct keystone distortion.

Height adjustment of the projected image → Focus adjustment), then align the 4 corners of the projected image



Adjusting Pincushion or Barrel Distortion (Pincushion)" after you select a source you want to project.

[Symptom2] In the case of keystone distortion (as illustrated), either the screen is directed slightly downward or the projector is directed slightly downward.

[Action] Tilt the bottom end of the screen to the front or rotate the rear feet (screen side) of the projector to correct keystone distortion.

C O

L R O

M N U

L T A

N N

S M R

O F

A A

E T N

C E L E

C R

F C P

Up Down

As illustrated in the diagram to the right below, when the top and bottom edges of the image are not parallel to each other, it can be suspected that the screen and the projector are not parallel to each other.

Down

Page 46

3. Projecting an Image (Basic Operation)

[Symptom 3] As illustrated in the diagram to the right, when the left edge of the image is widened vertically, either the projector is not placed straight in front of the screen or the projector is directed slightly to the left. Conversely, when the right edge of the image is widened vertically, either the projector is not placed straight in front of the screen or the projector is directed slightly to the right.

[Action] Place the projector straight in front of the screen. Make sure that the screen and the projector are parallel to each other.

Page 47

 Selecting a Source

Selecting the computer or video source

3. Projecting an Image (Basic Operation)

Using the Remote Control

Press any one of the COMPUTER, VIDEO or VIEWER buttons.

Selecting from Source List

Press and quickly release the SOURCE button on the projector cabinet to display the Source list. Each time the SOURCE button is pressed, the input source will change as follows: “Computer”, “DVI (DIGITAL/ANALOG)”, “Video” (VCR or laser disc player), “S-Video”, “Viewer” (slides on a PC card) or “LAN” (LAN card). To display the selected source, press the ENTER button.

Detecting the Signal Automatically

Press and hold the SOURCE button for a minimum of 1 second, the projector will search for the next available input source. Each time you press and hold the SOURCE button for a minimum of 1 second, the input source will change as follows:

VIDEO

ASPECT

PIC-MUTE

VOLUME

FREEZE

FOCUS

COMPUTER

AUTO ADJ.

HELP

PC CARD

SOURCE

SELECT

PC CARD

SOURCE

VIEWER

SLIDE

ZOOMFOCUS

3D REFORM

Computer → DVI (DIGITAL) → DVI (ANALOG) → Video → S-Video → Viewer → Computer → ...

If no input signal is present, the input will be skipped. When the input source you wish to project is displayed, release the SOURCE button.

SELECT

Page 48

3. Projecting an Image (Basic Operation)

 Optimizing an RGB Image Automatically

Adjusting the Image Using Auto Adjust

Optimizing an RGB image automatically. Press the Auto Adjust button to optimize an RGB image automatically.

[Poor picture]

[Normal picture]

ENTER

AUTO

ADJUST

ON/

STAND BY

SELECT

REFORM

POWER

STATUS

LAMP

EXIT

VIDEO

ASPECT

PIC-MUTE

VOLUME

FREEZE

COMPUTER

AUTO ADJ.

HELP

VIEWER

SLIDE

ZOOMFOCUS

3D REFORM

Press the Auto Adjust button to fine-tune the computer image or to remove any vertical banding that might appear and to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmering). This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This function also adjusts the clock phase to reduce video noise, dot interference or cross talk. This adjustment may be necessary when you connect your computer for the first time.

NOTE:

• Some signals may take time or not be displayed correctly

• The Auto Adjust function does not work for component or video signals.

• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually. See page 95.

 Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT jack (Stereo mini) on the projector can be adjusted.

NOTE: When no menus appear, the SELECT 왗 or buttons on the projector cabinet work as a volume control.

왘

Increase volume

Decrease volume

VIDEO

ASPECT

PIC-MUTE

VOLUME

FREEZE

COMPUTER

AUTO ADJ.

HELP

VIEWER

SLIDE

ZOOMFOCUS

3D REFORM

Page 49

3. Projecting an Image (Basic Operation)

 Adjusting Pincushion or Barrel Distortion (Pincushion)

If pincushion or barrel distortion become conspicuous, adjust with [Pincushion].

Reference

• Pincushion or barrel distortion in this projector The amount of pincushion and barrel distortion in this projector is 2% or less (TV distortion) in each of the

horizontal and vertical directions (for screen sizes of 40 inches to 100 inches). As an example, the amount of distortion with a screen size of 60 inches (121.9 cm/48.0” W x 91.4 cm/36.0” H) is

within approximately 12 mm/0.47” in the horizontal direction and within approximately 9 mm/0.35” in the vertical direction. When this projector is used with a 60-inch screen size, the amount of pincushion and barrel distortion is at a minimum.

bb bb

a: 1% or less of the screen height (2% or less as TV distortion)

b: 1% or less of the screen width (2% or less as TV distortion)

When the amount of pincushion or barrel distortion exceed 2% (TV distortion), please check whether the projector and screen setup conditions are suitable.

1 Press the 3D REFORM button of the projector or the remote control.

The [Pincushion] screen will appear.

• Press the SELECT 왖 or 왔 button and align the cursor with [Left/

Right], then press the SELECT ment of the left and right protrusions and indentations of the projected image.

왗

or 왘 button to allow adjust-

Screen (solid line) Projected area (dotted line)

Page 50

3. Projecting an Image (Basic Operation)

• Press the SELECT 왖 or 왔 button and align the cursor with [Top],

왗

then press the SELECT

or 왘 button to allow adjustment of the protrusions and indentations of the upper edge of the projected image.

• Press the SELECT 왖 or 왔 button and align the cursor with

왗

[Bottom], then press the SELECT

or 왘 button to allow adjustment of the protrusions and indentations of the lower edge of the projected image.

2. Press the ENTER button when [Pincushion] is completed.

Return to the menu.

3. Press the EXIT button a few times to make the menu disappear.

Screen (solid line) Projected area (dotted line)

NOTE:

• In the [Pincushion] screen, when the [Top] adjustment value is "0", adjustment of [Bottom] will not be possible*. Also note that when the adjustment value of the [Top] is a small value (on the order of +5), there will be almost no change of the image even when the [Bottom] is adjusted.

• In the [Pincushion] screen, when the [Bottom] adjustment value is less than "0", a small portion can be lost at the bottom area of the image. To display the lost portion, use the [Digital Zoom] function to reduce the size of the projected image*.

• When [Cornerstone] or [Keystone] has already been adjusted, selection of [Pincushion] will not be possible. To display [Pincushion], return the adjustment values of [Cornerstone] or [Keystone] to the factory shipping conditions.

* Each note for [Top] and [Bottom] is reversed when the [Ceiling Rear] or [Ceiling Front] is selected in [Orienta-

tion] .

Reference

The [Pincushion] screen can also be displayed from the menu by going to [Setup] → [Basic].

Page 51

3. Projecting an Image (Basic Operation)

쐆 Using the Laser Pointer

You can use the laser to draw your audience's attention to a red dot that you can place on any object.

CAUTION:

• Do not look into the laser pointer while it is on.

• Do not point the laser beam at a person.

• Do not allow children to use the laser pointer.

Press and hold the LASER button to activate the laser pointer.

O I R

C R

K O R L O C K

LASER

To disable the laser pointer, set the function switch to “Off”. Decide whether to enable or disable the laser, then set the switch as necessary using the tip of a thin ball-point pen. On this model, the other selector switch is not used.

OFF

Laser enable/disable switch

Not used

On: Enabled (the laser lights when the LASER button is pressed) [Factory default] Off: Disabled (the laser does not light even when the LASER button is pressed)

Disable the laser when using in an environment in which the unit is accessible to children.

Page 52

3. Projecting an Image (Basic Operation)

 Using the Electronic Pen (WT615 only)

The electronic pen and the projector’s sensors can be used to convert your whiteboard into a virtual touchscreen which allows you to operate your projector’s menu or use the ChalkBoard feature.

Important

• Be sure to set up the projector parallel to the screen. Otherwise, the actual pen stroke may not be displayed on the screen.

• Before you use the electronic pen for the first time or when you have changed the position of the projector or the screen size, be sure to use [Pen Calibration] to calibrate the electronic pen and the screen.

• Be sure to perform [Pincushion] correction before doing [Pen Calibration]. Otherwise, the actual pen stroke may not be displayed on the screen.

Pen Calibration

Calibrate so that pen touches are properly detected by the sensor on the WT615.

1. Press the MENU button on the remote control or the projector cabinet.

The menu will be displayed.

2. Press the SELECT 왘 button twice to select [Setup] and press the ENTER button.

The [Basic] menu will be displayed.

Page 53

3. Projecting an Image (Basic Operation)

3. Press the SELECT 왖 or 왔 button to select [Pen Calibration] and press the ENTER button.

One “O ”mark will be displayed on the screen.

4. Touch the circle “O” mark lightly with the electronic pen.

Another “O” mark will be displayed on the screen.

Touch

Use the same procedure each time a circle "O" mark appears until you touch all the marks.

Your calibration settings are now saved.

This completes “Pen Calibration”.

NOTE: Hold the electronic pen upright against the screen when using it. Otherwise, the actual movement of the electronic pen may not be displayed on the screen.

Page 54

3. Projecting an Image (Basic Operation)

ChalkBoard Function

You can use the electronic pen to operate the ChalkBoard function. See also page 55.

NOTE: Hold the electronic pen upright against the screen when using it. Otherwise, the actual pen stroke may not be displayed on the screen. The electronic pen must be used at an angle less than 20 degrees from the upright position.

• Start ChalkBoard

Press and hold the button B on the electronic pen for a minimum of 0.5 second.

Button B

The ChalkBoard toolbar will be displayed at the bottom right of the screen.

• Drawing lines

[1] Tap the Drawing tool palette icon [2] Tap the Line thickness palette icon [3] Tap the Color palette icon [4] Touch and hold the pen tip to the screen lightly to write characters or draw patterns.

lightly and then tap the Pen icon.

and then tap your preferred line thickness icon.

lightly and then tap your preferred line color icon.

• Erasing lines

[1] Tap the Drawing tool palette icon [2] Tap the Line thickness palette icon [3] Touch and hold the pen tip to the screen lightly to erase lines.

• Clear the Screen

Tap the Clear icon

• Exit ChalkBoard

Tap the Exit icon .

and then tap the Eraser icon .

and then tap your preferred line thickness icon.

Reference

• On the WT610 you can use the ChalkBoard function when connecting a USB mouse to the projector. See page

53 for more details.

• Notes and drawings that you draw on the screen can be captured and saved to the supplied USB memory device. See page 56.

• About the supplied eBeam Interactive software eBeam Interactive software is contained on the supplied CD-ROM (User Supportware 2 Plus) included with the projector. This software can be used to convert your screen into:

-A digital whiteboard with powerful meeting sharing capabilities (using eBeam software’s meeting applica-

tion); or

-A virtual touchscreen which allows you to completely control your computer and all of your applications

directly from the screen using the electronic pen.

Page 55

 Turning off the Projector

To turn off the projector:

3. Projecting an Image (Basic Operation)

Cabinet controls Remote control

1. Press the POWER (ON/STAND BY) button on the projector

cabinet or the POWER OFF button on the remote control. The "Power Off / Are you sure?" message will appear.

2. Press the ENTER button or the POWER (ON/STANDBY) or

the POWER OFF button again.

The POWER indicator will glow orange. After the projector turns off, the cooling fans keep operating for 90 seconds (Cooling-off time).

NOTE: Immediately after turning on the projector and displaying an image, you cannot turn off the projector for 60 seconds.

3. Turn off the Main Power switch. The POWER indicator will

go out.

CAUTION Do not unplug the power cable from the wall outlet or do not turn off the main power under any one of the following circumstances. Doing so can cause damage to the projector or PC card:

• While the projector lamp is On.

• While the cooling fans are running. (The cooling fans continue to work for 90 seconds after the projector is turned off).

• While the PC CARD Access Indicator lights. Doing so can damage your PC memory card.

ENTER

AUTO

ADJUST

ON/

STAND BY

ENTER

AUTO

ADJUST

ON/

STAND BY

SELECT

REFORM

POWER

STATUS

LAMP

REFORM

POWER

STATUS

LAMP

OFF

POWER

LASER

MAGNIFY

EXIT

MAGNIFY

EXIT

PAGE

POINTER

DOWN

POWER

LASER

POINTER

PAGE

DOWN

OFF

Page 56

쐅 After Use

Preparation: Make sure that the main power is turned off.

1. Close the mirror cover.

After closing the mirror cover, lock the mirror cover by sliding the mirror cover lock switch to the lock position.

3. Projecting an Image (Basic Operation)

U N

O I R

K O R

L O C

U N

O R

O C

2. Unplug the power cable.

3. Disconnect any other cables.

4. Retract adjustable tilt feet if extended.

5. Put the supplied dust-proof cover over the projector cabinet.

Page 57

Convenient Features

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 Tu rning Off the Image and Sound .............................. 51

쐇 Freezing a Picture...................................................... 51

쐋 Using the Pointer ....................................................... 51

쐏 Enlarging and Moving a Picture................................. 52

쐄 Getting Integrated Help ............................................. 52

쐂 Using a USB Mouse .................................................. 53

쐆 Using the Remote Mouse Function ........................... 54

 Making Freehand Drawings

on a Projected Image (ChalkBoard) ...................... 55



Storing Images Displayed on the Projector on the PC card

or USB memory (Capture)

쐅 Preventing Unauthorized Use of the Projector .......... 57

쐈 Using a USB Memory Device or

USB Memory Card Reader.................................... 62

쐉 Operation Using an HTTP Browser ........................... 63

씈 Using the Projector to Operate a Computer Connected

on a Network (Desktop Control Utility 1.0) ............ 66

......................................... 56

Page 58

4. Convenient Features

쐃 Turning Off the Image and Sound

Press the PIC-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound.

NOTE: The menu still remains visible even when the image is turned off.

쐇 Freezing a Picture

Press the FREEZE button to freeze a picture. Press again to resume motion.

NOTE: Pressing the MENU button will display the Capture menu that allows you to capture a freezed image. See page 56 for more information.

쐋 Using the Pointer

You can use one of nine pointers to draw your audience's attention to the portion of a projected image you want.

NOTE: You can select one pointer from the menu. See page

125.

Press the POINTER button to display the pointer.

VIDEO

VIEWER

COMPUTER

AUTO ADJ.

SLIDE

ASPECT

HELP

PIC-MUTE

ZOOMFOCUS

VOLUME

FREEZE

3D REFORM

VIDEO

VIEWER

COMPUTER

AUTO ADJ.

SLIDE

ASPECT

HELP

PIC-MUTE

ZOOMFOCUS

VOLUME

FREEZE

3D REFORM

OFF

POWER

LASER

MAGNIFY

PAGE

POINTER

DOWN

Press the Pointer button to display the pointer.

Use the SELECT 왖왔왗 or 왘 button to move the pointer. Press the POINTER button again. The pointer will disappear.

OFF

POWER

LASER

MAGNIFY

PAGE

POINTER

DOWN

Use the Select button to move the pointer.

Page 59

쐏

Enlarging and Moving a Picture

You can enlarge the area you want up to 400 percent.

To do so:

4. Convenient Features

1. Press the POINTER button to display the pointer.

2. Move the pointer to the area you want to enlarge.

3. Enlarge the selected area.

When the MAGNIFY (+) button is pressed, the image is magnified and the magnify icon will be displayed. To magnify the selected area,

왖왔왗

use the SELECT

or 왘 button to move the magnify icon and press the MAGNIFY (+) button.

OFF

MAGNIFY

OFF

MAGNIFY

OFF

MAGNIFY

POWER

LASER

PAGE

POINTER

DOWN

POWER

LASER

PAGE

POINTER

DOWN

POWER

LASER

POINTER

PAGE

DOWN

4. Return the image to the original size.

Press the MAGNIFY (-) button until the magnify icon changes to the pointer.

쐄 Getting Integrated Help

You get the contents about Help in English, German and Japanese.

VIDEO

VIEWER

COMPUTER

AUTO ADJ.

SLIDE

ASPECT

HELP

PIC-MUTE

ZOOMFOCUS

VOLUME

3D REFORM

FREEZE

Display Help

OFF

POWER

LASER

MAGNIFY

POINTER

OFF

POWER

LASER

MAGNIFY

POINTER

Exit Help

DOWN

PAGE

Page 60

4. Convenient Features

쐂 Using a USB Mouse

Using a USB mouse gives you a smooth operation. A commercially available USB mouse can be used.

PCCONTROL

PC CARD

REMOTE

NOTE: There may be some brands of a USB mouse that the projector does not support.

S-VIDEO IN DVI-I IN

AUDIO IN

VIDEO IN

/MONO

USB port (Type A)

Operating the Menus using the USB mouse

Mouse Cursor

When connecting a USB mouse to the USB port (Type A) of the projector, you get a mouse cursor on the screen. Unless you use your USB mouse within 10 seconds, the mouse cursor disappears.

NOTE: You can change the shape of the mouse cursor. To do so, select the menu → [Setup] → [Tools] → [Mouse] “Mouse Pointer”.

Menu Display

Clicking with the right mouse button displays the menu. To close the menu, click anywhere in the background.

Adjusting and Setting Display

You can select a menu item and click with the left mouse button to make adjustments and settings.

USB

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

→

Using the middle button on the mouse

The projector supports the middle button on your mouse. With the middle button you can do the following:

•You can use a scroll bar in the menu or in help.

•You can click the middle button to display or hide the ChalkBoard toolbar.

Example:

Click (or press and hold) the left mouse button on the SELECT 왗 or 왘 to adjust the brightness. Or click and drag the left mouse button on the slide bar horizontally to adjust it.

To save the adjustments, click

. The display is closed.

• Click with the left mouse button to display a description of the selected menu item.

• Click and drag the title bar with the left mouse button to move the adjustment or setting dialog box.

Operating your computer’s mouse using the USB mouse connected to the projector

1. Connect a commercially available USB mouse to the USB port (Type A) of the projector.

2. Use the supplied USB cable to connect the USB port (Type B) of the projector and the USB port (Type A) of

your computer.

NOTE:

• Operation may be changed depending on condition of connection with the USB port (Type B) of the projector.

• When the menu is displayed, the USB mouse operates the projector. When the menu is not displayed, the USB mouse operates your computer.

• This feature is available only on Windows 98, Windows Me, Windows 2000 and Windows XP

Page 61

4. Convenient Features

쐆 Using the Remote Mouse Function

The built-in remote mouse function enables you to operate your computer's mouse functions from the remote control. It is a great convenience for clicking through your computer-generated presentations.

Connecting to your computer for the remote mouse function

If you wish to use the remote mouse function, use the supplied USB cable to connect the USB port (Type B) of the projector and the USB port (type A) of your computer.

NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change your computer settings.

When using the USB Port

For PC, the remote mouse function can only be used with a Windows 98, Windows ME, Windows XP or Windows 2000 operating system.

PCCONTROL

PC CARD

REMOTE

S-VIDEO IN DVI-I IN

AUDIO IN

VIDEO IN

/MONO

USB

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

USB port (Type B)

USB cable (supplied)

NOTE: In Windows XP, if the mouse cursor will not move correctly, do the following: Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer Options tab].

NOTE: Wait at least 5 seconds after disconnecting the USB cable before reconnecting it and vice versa. The computer may not identify the built-in mouse receiver if it is repeatedly connected and disconnected in rapid intervals.

Operating your computer’s mouse from the remote control

You can operate your computer's mouse from the remote control.

PA GE (UP) (DOWN) Button

SELECT Button 왖왔왗왘:moves the mouse cursor on your computer. L-CLICK Button: works as the mouse left button. R-CLICK Button: works as the mouse right button.

NOTE:

• When the menu is displayed, using the SELECT of both the menu and the mouse at the same time. To avoid this, turn off the menu and operate the mouse.

• With the menu, the Viewer or the ChalkBoard toolbar displayed, you can use the mouse to operate the projector while enlarging an image with the MAGNIFY (+) or (–) button.

•To display the menu, press the MENU button on the remote control or the projector cabinet.

: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint

on your computer.

왖왔왗

or 왘 button to operate your computer’s mouse will affect the operation

NOTE: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user documentation or online help supplied with your computer.

Page 62

4. Convenient Features

 Making Freehand Drawings on a Projected Image (ChalkBoard)

The ChalkBoard feature allows you to write and draw messages on a projected image.

NOTE: The ChalkBoard feature is available only when the supplied electronic pen (WT615 only) or a USB mouse is used.

To display the ChalkBoard tool bar, click the middle button on your mouse, press and hold the button B of the electronic pen for a minimum of 0.5 second, or select [Setup] → [Tools] → [ChalkBoard] from the menu.

Selecting Board Color [Board Color]

This option allows you to select a board color of ChalkBoard.





쐅쐉씈

씋











The tool bar contains the following icons.

 Drag ................................... Drags to move the tool bar.

 Drawing tool palette ........... Displays a drawing tool palette.

 Pen ..................................... Displays the pen tool that you can draw or paint with.

 Eraser ................................. Erases part of a drawing.

 Box frame ........................... Draws a box frame.

 Box paint ............................ Paints a box shape.

 Line Thickness palette ........Displays the pen or eraser palette containing four lines of different thickness from which you can select a line

 Color palette ....................... Displays the color palette from which you can select a color you prefer for “Box frame” or “Boxpaint”.

 Clear ................................... Clear the drawing completely from the ChalkBoard screen.

쐅 Capture ............................... Captures a drawing on the ChalkBoard screen and save it in PNG format to your PC-card inserted into the PC

쐈

Drive (not displayed on WT610)

쐉 Undo .................................. Undoes the last operation.

씈 Redo ...................................Redoes the last undone operation performed with Undo.

씉 Page number ...................... Use or to select a ChalkBoard page number between 1 and 4.

씊 Hide .................................... Hides the tool bar. Clicking anywhere on the screen displays the ChalkBoard tool bar again.

씋 Exit ..................................... Clears the complete drawing and exits the ChalkBoard.

you prefer.

card slot of the projector.

... Switches between PC Card slot or USB memory. USB memory devices are available for WT615 only.

쐈

씉 씊

NOTE:

•Your drawings will be stored in memory after a given time period. However, when a resolution is changed by switching a signal or changing signal type, some picture information may be lost.

• Changing the [Board Color] will clear the current drawing.

Page 63

4. Convenient Features

 Storing Images Displayed on the Projector on the PC card or USB memory (Capture)

The Capture features allows you to capture an image from a source that is currently being displayed. The image is saved as JPEG in the PC card or USB memory.

[Important]

• USB memory devices are not available for the Capture function on the WT610.

• When saving captured images to a USB memory device on the WT615, be sure to use the USB memory device

included with the WT615. A commercially available USB memory device may be damaged. Also do not use a commercially USB memory card reader. Using a USB memory card reader may cause damage to a flash memory card.

NOTE:

• Unless a PC card or USB memory is inserted into the PC Card slot or USB port of the projector, the Capture feature is not available.

• The "Card Error" display means that the free space of the PC card or USB memory is insufficient for saving images. Make more space available on the card by erasing unwanted images with your PC. The number of images that can be captured depends on the size of the PC card.

• Be sure not to turn off the power or remove the PC card or USB memory while capturing an image. Doing so could cause a loss of the data in the PC card or USB memory or damage to the card itself.

• The Capture function is not available for DVI digital signal.

Preparations:

Insert the PC card into the PC card slot or USB memory into USB port of the projector. Insert the PC card so that the end with the insertion direction arrow on the top goes in first. * Press the eject button to eject the card.

1. Project the image you wish to store on the projector.

2. Press the FREEZE button on the remote contorol.

3. Press the MENU button to display the Capture menu.

Capture.................. Captures an image and save it as a JPEG file in a PC card or USB memory.

Drive...................... Select the PC Card or USB memory. You can capture an image and save it to your PC card or USB memory.

Exit ........................ Exits the Capture function. Another option to exit the Capture function is to press the MENU or EXIT button

on the remote control or projector cabinet.

4. Press the FREEZE button to resume the motion.

NOTE: Captured images with a higher resolution than the projector's native resolution cannot be displayed correctly.

• File size of the captured image varies depending on the resolution of an input signal.

• An hourglass indicating that an image is being captured appears on the projector's display. Do not eject the PC card or turn off the projector's power while this icon is displayed. Doing so will damage the PC card data. If the PC card data is damaged, use a computer to repair the data.

• The “Drive” icon will not be displayed on the WT610.

Page 64

4. Convenient Features

쐅 Preventing Unauthorized Use of the Projector

Assigning a keyword prevents the projector from being used by unauthorized individuals.

Assigning a Keyword for the first time

1. Press the MENU button.

The menu will be displayed.

2. Press the SELECT 왘 button to select the Setup submenu and press the ENTER button.

The page tab “Basic” will be highlighted.

WT615 only

3. Press the SELECT 왘 button twice to select the page tab “Security”.

Page 65

4. Press the SELECT 왔 button four times to select “Security”.

5. Press the ENTER button to display the Security screen.

4. Convenient Features

6. Press the SELECT 왔 button once to select the Keyword entry box and press the ENTER button.

The Software keyboard will be displayed.

Page 66

4. Convenient Features

7. Enter an alphanumeric keyword using the Software keyboard

For example, to enter “1234”, follow the steps 7-1 to 7-4 below.

NOTE:

• Please make a note of your keyword.

• Do not use spaces (SP) in your keyword.

7-1. Select the number “1” and press the ENTER button.

The asterisk “

7-2. Press the SELECT

The asterisk “

7-3. For “3” and “4”, use the same procedure as step 7-2.

The asterisk “

7-4. Press the SELECT

The Software keyboard will disappear.

8. Press the SELECT 왖 button once to select“Disable” and press the SELECT 왗 button to select “Enable”.

쏄

” will be displayed in the Keyword entry box.

왘

button once to select “2” and press the ENTER button.

쏄쏄

” will be displayed in the Keyword entry box.

쏄쏄쏄쏄

” will be displayed in the Keyword entry box.

왔

button to select “OK” and press the ENTER button.

9. Press the SELECT 왔 button to select “OK” and press the ENTER button.

The confirmation screen will be displayed.

.Press the ENTER button.

The Security Function is now enabled.

NOTE: A PC card can be used as a protect key. You can skip the keyword entry by inserting a registered PC card when turning on the projector. See page 107.

Page 67

4. Convenient Features

Checking If Security is enabled

Tu rn off the projector and turn it back on to check if the Security function is enabled.

1. Press the POWER (ON/STAND BY) button.

The "Power Off / Are you sure?" message will appear. Press the ENTER button or the POWER (ON/STAND BY) or the POWER OFF button again. The lamp lights off and the POWER indicator flashes orange. Please wait until the POWER indicator changes

from flashing to steady light.

2. When the POWER indicator lights steady orange, push the Main POWER switch to the off position (O).

The projector will turn off.

3. Push the Main POWER switch to the on position (I).

The POWER indicator lights orange. The projector is in standby condition.

4. Press and hold the POWER (ON/STAND BY) button for a minimum of two seconds.

The projector will turn on. The “Projector is locked! Enter your keyword.” message will be displayed at the bottom of the screen.

5. Press the MENU button.

The Keyword entry screen will be displayed

6. Press the ENTER button.

The Software keyboard will be displayed.

7. Use the same procedures as steps 1 to 7 described in the “Assigning a Keyword for the first time”

section to enter “1234”.

Each time one number is entered, an “ keyword is hidden.

8. After entering your keyword, select “OK” and press the ENTER button.

The Software keyboard will disappear. This will allow you to operate the projector.

쏄

” (asterisk) will appear. Keyword appears as asterisks so the real

Page 68

4. Convenient Features

Disabling the Security

1. Press the MENU button.

The on-screen menu will be displayed.

NOTE: Immediately after the projector has been turned on and the “Projector is locked! Enter your keyword.” message is displayed at the bottom of the screen, pressing the MENU button will display the Keyword entry page. At this time, pressing the MENU button will display the on-screen menu.

2. Press the SELECT

The page tab “Basic” will be highlighted.

3. Press the SELECT

4. Press the SELECT

The Keyword entry screen will be displayed

5. Press the ENTER button.

The Software keyboard will be displayed.

6. Use the same procedures as steps 1 to 7 described in the “Assigning a Keyword for the first time”

section to enter “1234”.

Each time one number is entered, an “ keyword is hidden.

7. After entering your keyword, select “OK” and press the ENTER button.

The Software keyboard will disappear. The Security screen will be displayed.

왘

button to select “Setup” and press the ENTER button.

왘

button twice to select the page tab “Security”.

왔

button four times to select “Security” and press the ENTER button.

쏄

” (asterisk) will appear. Keyword appears as asterisks so the real

8. Highlight “Enable” and press the SELECT 왘 button to select “Disable”.

9. Press the SELECT 왔 button to select “OK” and press the ENTER button.

The Security Function is now disabled.

NOTE: Do not forget your keyword. However, if you forget your keyword, NEC will provide you with your Release Code.

Page 69

4. Convenient Features

쐈

Using a USB Memory Device or USB Memory Card Reader

The projector is compatible with either a USB memory device (A USB memory device is supplied with the WT615) or USB memory card reader which supports the viewer and security features.

[Important]

When saving captured images to a USB memory device on the WT615, be sure to use the USB memory device included with the WT615. A commercially available USB memory device may be damaged. Also do not use a commercially USB memory card reader. Using a USB memory card reader may cause damage to a flash memory card.

•To use a USB memory device or USB memory card reader,

connect the device to the USB port (type A).

• Select one of the drive icons for your USB memory in a pane

PCCONTROL

PC CARD

REMOTE

S-VIDEO IN DVI-I IN

AUDIO IN

VIDEO IN

/MONO

AUDIO IN AUDIO OUT

USB

DVI-I COMPUTER

COMPUTER IN MONITOR OUT

USB

on the left side of the Viewer window.

•To use a USB memory device as a Protect key for Security

function, select one from the Drive icons in the Security setting screen. See page 107.

• The drive icon is not displayed on the WT610.

NOTE:

• Some USB memory devices (brands) or USB memory card readers may not work.

• The projector does not support NTFS formatted flash memory card or USB memory device. Be sure to use a flash memory card or USB memory device formatted with the FAT32, FAT16 or FAT file system. To format your flash memory card or USB memory device in your computer, refer to the document or help file that comes with your Windows.

•You cannot use a USB memory device and a USB memory card reader when connecting a USB mouse to the projector.

• Do not do the following while the USB memory device or USB memory card reader’s access indicator is lit or flashing (while data is being accessed.) Doing so can damage your USB memory device or USB memory card reader in the reader. Back up your data in case it will need to be restored. * Pulling out the USB memory device or USB memory card reader from the USB port of the projector. * Pulling out the memory card from the USB memory card reader *Turning off the main power switch or unplugging the power cable.

• The drive for ”USB 1-4” is displayed only when the USB memory device or USB memory card reader is connected to the projector. The drive for “USB 1-4” may be displayed differently from the one in the USB memory card reader.

• Some USB memory devices (brands) or USB memory card readers cannot be used as Protect key for the projector’s Security function.

Page 70

4. Convenient Features

쐉 Operation Using an HTTP Browser

Overview

The use of HTTP server functions will allow control of the projector from a web browser without the installation of special software. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser. (This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will vary depending on the version of browser. Please refer to the help files and the other information provided in your software.)

NOTE: * The display’s or button’s response can be slowed down or operation may not be accepted depending the settings of your

network. Should this happen, consult your network administrator.

* The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and

repeat. If you still can’t get any response, turn off and back on the projector. Access is gained to the HTTP server functions by specifying http:// <the projector’s IP address> /index.html in the entry column of the URL.

CAUTION:

Do not use the HTTP Server functions and PC Control Utility 3.0 included on the supplied CD-ROM. Using both at

the same time may result in a connection failure or slow response.

Preparation Before Use

Make network connections and set up the projector and confirm that it is complete before engaging in browser operations. (See “Setting LAN Mode” on page 111.) Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation. It is recommended that a proxy server not be used unless it is unavoidable.

Handling of the Address for Operation via a Browser

Regarding the actual address that is entered for the address or entered to the URL column when operation of the projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the projector has been registered to the domain name server by a network administrator, or the host name corresponding to the IP address of the projector has been set in the “HOSTS” file of the computer being used.

Example 1: When the host name of the projector has been set to “pj.nec.co.jp”,

http://pj.nec.co.jp/index.html is specified for the address or the entry column of the URL.

Example 2: When the IP address of the projector is “192.168.73.1”, access is gained to the

HTTP server functions by specifying http://192.168.73.1/index.html for the address or the entry column of the URL.

Page 71

Structure of the HTTP Server

4. Convenient Features

Power: This controls the power of the projector.

On ................... Power is switched on.

Off ................... Power is switched off.

Picture: Controls the video adjustment of the projector.

Brightness 왖 ... Increases the brightness adjustment value.

Brightness 왔 ... Decreases the brightness adjustment value.

Contrast 왖 ...... Increases the contrast adjustment value.

Contrast 왔 ...... Decreases the contrast adjustment value.

Color 왖 ........... Increases the color adjustment value.

Color 왔 ........... Decreases the color adjustment value.

Hue 왖 ............. Increases the hue adjustment value.

Hue 왔 ............. Decreases the hue adjustment value.

Sharpness 왖 ... Increases the sharpness adjustment value.

Sharpness 왔 ... Decreases the sharpness adjustment value.

• The functions that can be controlled will vary depending on the signal being input to the projector.

Volume: This controls the volume of the projector.

왖 ..................... Increases the volume adjustment value.

왔 ..................... Decreases the volume adjustment value.

Source Select: This switches the input connector of the projector.

Computer ........ Switches to the COMPUTER IN connector.

DVI (ANALOG/

DIGITAL) ....... Switches to the DVI-I IN connector.

Video ............... Switches to the VIDEO IN connector.

S-Video ........... Switches to the S-VIDEO IN connector.

Viewer ............. Switches to the Viewer.

LAN ................. Switches to a LAN signal.

Page 72

4. Convenient Features

Mute: This controls the mute function of the projector.

Picture On ....... Mutes the video.

Picture Off ....... Cancels the video muting.

Sound On ........ Mutes the audio.

Sound Off ........ Cancels the audio muting.

OSD On .......... Mutes the on-screen display.

OSD Off .......... Cancels the muting of the on-screen display.

All On .............. Mutes each of the video, audio, and on-screen display functions.

All Off .............. Cancels the muting of each of the video, audio, and on-screen display functions.

Projector Status: This displays the condition of the projector.

Refresh ....................... Updates the display of the following conditions.

Remaining Lamp Time

Projector Usage .......... Displays how many hours the projector has been used.

Lamp Hour Meter ........Displays how many hours the lamp has been used.

Error Status ................. Displays the status of errors occurring within the projector.

... Displays the remaining life of the lamp as a percentage.

Page 73

4. Convenient Features

씈 Using the Projector to Operate a Computer Connected on a Network (Desktop Control Utility 1.0)

When Desktop Control Utility 1.0 on the included User Supportware 2 CD-ROM is installed on the computer, that computer can be operated using the projector over a network. For example, say you have a PowerPoint file on a computer in your office that you want to use for a presentation at a meeting. If the computer in the office is connected by LAN to the projector in the meeting room, the projector can be operated to project the image of the desktop of the computer (Windows 2000 or XP) in the office and display the PowerPoint file during the meeting. This eliminates the need for taking the computer from the office to the meeting room.

Meeting room

Office

Disclaimer

You can use the Desktop Control Utility 1.0 to operate a computer located in a separate room from the projector over a network. This means there might be potential security risks that you may be exposed to which could cause damage by unauthorized access or illegal use. We recommend you take some measures to prevent third parties from unauthorized access to your data or information. We share neither liability nor responsibility to any loss or damages arising from information leak or power down without notice.

NOTE: In Windows operating system, click “Control Panel” → “Power Options” → ”System Standby” → ”Never”. This will disconnect a LAN connection when the computer goes in standby mode.

NOTE: To use the Desktop Control Utility 1.0, you need to have a USB mouse inserted into the USB port of the projector. The WT615 does not require connection with a USB mouse because the electronic pen can be used for a USB mouse. This section explains the operation by using a USB mouse.

Page 74

4. Convenient Features

Operations on the Computer

1. Connect the computer to the LAN and make the required settings.

2. Install Desktop Control Utility 1.0 on the computer.

•For instructions on installation, refer to the included “Wired and Wireless Network Setup Guide”.

•For instructions on operating the software, see the Desktop Control Utility 1.0’s help file.

3. Prepare the documents to be presented at the meeting and save them on the computer.

4. Start up Desktop Control Utility 1.0.

The Startup password window appears.

Window at the first startup Window after entering your startup password

Important:

•Your startup password will be required each time you start Desktop Control Utility 1.0.

• If you forget or lost your startup password,

5. Input the startup password and click “OK”.

The “Current password” input window appears.

install the program again.

NOTE: The "Current password" will be changed each time you start Desktop Control Utility 1.0.

6. Make a note of the password.

7. Click “OK”.

Desktop Control Utility 1.0 starts.

Go to the room where the projector is installed, taking the password you made a note in the previous Step 6.

Page 75

4. Convenient Features

Operations on the projector – Connecting to the computer

1. Make the LAN settings on the projector.

Make the LAN settings at [Setup]

2. Connect a commercially available USB mouse to the projector. (See page 53)

3. Click anywhere on the screen with the USB mouse.

The menu appears.

4. Click [Source], then click “LAN”.

The help message is displayed.

The message is displayed only when a password for Desktop Control Utility 1.0 is not assigned.

5. Follow the message to press the MENU button on the projector cabinet or the remote control.

The connections bar appears at the bottom left of the screen.

→

[Installation] → [LAN Mode] in the menu. (See page 111)

6. Click the password input icon .

7. Click “Entry”.

The password input window appears.

8. Click .

The character input window appears. (See page 148.)

Page 76

4. Convenient Features

9. Input the password you made a note of in the previous Step [6] in “Operations on the Computer”.

10. Input the password and click “OK”.

The password input window is turned off.

11. Click the PC search icon

The PC search window appears.

12. Click “OK”.

The connection selection window appears.

•To search by inputting the IP address of the connected computer, click “Input IP Address”, then click “OK”.

13. Click the computer to which you want to connect, then click “OK”.

The desktop of the connected computer appears.

on the PC Search window, click

NOTE: Once the desktop appears, the menu will no longer appear when the USB mouse is clicked. To display the menu while the desktop is displayed, press the button on the projector itself or on the remote control.

Operations on the projector –Operating the desktop

A USB mouse connected to the projector can be used to operate the displayed desktop. If the MENU button on the projector cabinet or the remote control is pressed while the desktop is displayed, an additional operations bar appears at the bottom left of the screen.

햲햳햴햵

Page 77

4. Convenient Features

The following operations are available only with buttons on the projector cabinet or the remote control.

Disconnect icon ................. Use to cut off communications with the computer.

햲

Shift icon ............................ Select this icon and press the ENTER button to set the shift lock mode. Select this icon and

햳

press the ENTER button again to cancel the shift lock mode.

Ctrl icon ............................. Select this icon and press the ENTER button to set the control lock mode. Select this icon

햴

and press the ENTER button again to cancel the control lock mode.

햵

Esc icon ............................. Use to do the same operation as when the “Esc” button on the computer is pressed. Use it

for example to stop a PowerPoint slideshow.

Operations on the projector – Disconnecting communication

1. Press the MENU button while the desktop is displayed.

The additional operations bar appears at the bottom left of the screen.

2. Select the disconnect icon and press the ENTER button.

The connections bar appears at the bottom left of the screen.

To reconnect the communication, click the PC search icon and repeat steps 12 and 13 in the previous page.

NOTE: Disconnection is possible by clicking the projector icon and then "Disconnect" on the taskbar.

Operations on the projector – Exiting Desktop Control Utility 1.0

1. Click the projector icon on the taskbar while the desktop is displayed.

The pop-up menu will be displayed

2. Click “Exit”.

Desktop Control Utility 1.0 quits

3. Click anywhere on the screen.

The menu will be displayed.

4. Click [Source] and then click any other source than "LAN".

The menu will turn off.

Page 78

Using the Viewer

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 Making the Most out of the Viewer Function.............. 72

 Operating the Viewer Function from

the Projector (playback) ......................................... 73

쐋 Changing Background Logo ...................................... 79

Page 79

5. Using the Viewer

 Making the Most out of the Viewer Function

Features

You can view presentation data, capture and play images on the projector. A PC card is used to view presentation data prepared on the computer and to capture and play images projected with the projector. The Viewer feature allows you to view slides stored on a PC memory card (referred to as PC card in this manual) or USB memory on the projector. Even if no computer is available, presentations can be conducted simply with the projector. This feature is convenient for holding presentations at meetings and in offices, as well as for playing images taken on digital cameras.

NOTE:

• USB memory devices are available for WT615 only. USB memory devices are not available for the Capture function on the WT610.

•To use the Viewer, first you need to create presentation materials on your PC (JPEG, BMP, GIF* For creating presentation materials using the Ulead Photo Explore 8.0, see the supplied "Wired and Wireless Network Setup Guide" or On-line help in Ulead Photo Explorer 8.0.

Both PNG and GIF format support non-interlaced images only.

“Index” file is a file created using the Ulead Photo Explore 8.0 contained on the supplied NEC User Supportware 2 CD-ROM.

See the “NEC User Supportware 2 User’s Guide” included on the NEC User Supportware 2 CD-ROM for installing the Ulead Photo Explore 8.0 on your computer.

Easy to use

• Presentations can be started immediately simply by inserting a PC card or USB memory (not supplied)

• Easy slide switching

• Remote control operation

•Jumping to a list of slides or any specific slide

, PNG*1, Index*2 files).

Simple utility software (for computer)

• Ulead Photo Explore 8.0SE Basic operable on Windows XP/Windows 2000.

• Slides can be created by capturing the currently displayed image.

• Control screen for displaying lists of slides and editing.

* Microsoft, Windows and PowerPoint are registered trademarks of Microsoft Corporation.

Page 80

5. Using the Viewer

 Operating the Viewer Function from the Projector (playback)

This section describes the operation for showing slides created using the Viewer function with the projector. It is also possible to make slides directly from the images projected with the projector.

Projecting slides (Viewer)

Preparation: Use the Capture feature to store graphic files (JPEG, BMP, non-interlaced GIF or non-interlaced PNG files) in a PC card or USB memory inserted into the projector’s slot. Or store JPEG or BMP files in a PC card or USB memory inserted into your PC.

NOTE: USB memory devices are not available for the Capture function on the WT610.

1. Insert a PC card into the PC card slot or USB memory into the USB port of the projector.

2. Press the VIEWER button on the remote control or select the “Viewer” from the source list.

An image stored in the PC card or USB memory will be displayed.

3. Press the MENU button to display the Viewer menu.

The Viewer menu will appear when you press the MENU button on the remote control or the projector cabinet.

The Viewer menu includes the following commands:

Play ................... Plays back automatically or manually depending on the setting in Options. This allows you to move on to the

next slide when "Manual Play" is selected in the “Play Mode”.

Stop ................... This allows you to stop Auto Play while you are playing back and to resume playing from the selected slide

or folder when "Auto Play" is selected in the “Play Mode”.

Thumbnails........ Displays a list of thumbnails of Graphic files stored in the PC card inserted into the projector.

Delete ................ Deletes a captured slide(s) or all the captured slides in the Capture - specific folder.

Logo .................. Replace the default background logo with another logo in JPEG, BMP, non-interlaced GIF or non-interlaced

PNG format.

Options .............. Displays the Viewer setting options. See page 75 for more details.

4. Select “Play” and then press the ENTER button to display the first slide or to start playing slides automatically.

Page 81

Viewer Window Elements

“_ _CAP_ _” folder

Number of files

5. Using the Viewer

Thumbnail/file name

List of folders

Slot 1

_CAP_ _RESTORE RECYCLED

3 Files

0000.jpg 0001.jpg 0002.jpg

Scroll bar

Cursor (orange)

Information

1/3 0000.jpg 60KB

select : ENTER

Cursor ..................................... Indicates the selected slide, folder or drive.

List of folders .......................... Indicates folders contained on a PC card or USB memory.

Information .............................. Indicates information of the selected file or folder.

Folder: folder name, creation date (month/day/year), creation time (hour/minute). File: slide number/number of displayable slides in a folder, file name, creation date (month/day/

year), creation time (hour/minute), file size.

Number of files ........................ Indicates number of displayable slides in the selected folder. The maximum number of images

recognized as slides within one directory is about 1000.

Thumbnail/file name ................ Indicates thumbnails and names contained in a folder.

Scroll bar ................................. Used to view folders or files not visible in the window.

“__CAP__” folder .................... Will be created when the Capture is performed.

Page 82

5. Using the Viewer

Setting Option for Viewer

Play Mode:

Manual .................. Views a slide manually when the Viewer source is selected.

Auto ...................... Plays back slides automatically when the Viewer source is selected.

Interval:

Specifies interval time between 5 and 300 seconds.

Start:

Specifies start screen when the Viewer source is selected.

Show Thumbnails:

Selecting the Viewer source will display a list of thumbnails of graphic files stored in the PC card or USB memory when “On” is selected.

“On”

3 Files

0000.jpg 0001.jpg 0002.jpg

select : ENTER

folder :

EXIT

Slot 1

_CAP_ _RESTORE RECYCLED

1/3 0000.jpg 60KB

“Off”

3 Files

0000.jpg 0001.bmp 0002.jpg

select : ENTER folder :

EXIT

Slot 1

_CAP_ _RESTORE RECYCLED

1/3 0000.jpg 60KB

Sort:

Rearranges the slides or thumbnails by name, extension, date or size.

NOTE: This setting is not available for the following folders: * The "__CAP__" folder for captured images * Folders created with the "Output Viewer" feature of Ulead Photo Explorer 8.0 or with Viewer PPT Converter 3.0

OK/Cancel:

To close the Options menu with saving changes, select "OK" and press the ENTER button. To close the Options menu without saving changes, select "Cancel" and press the ENTER button.

Page 83

5. Using the Viewer

Exiting Viewer

To exit Viewer, switch to another input such as Computer, DVI (DIGITAL/ANALOG), Video, S-Video or LAN.

*To switch to another input, there are two ways: * Press the COMPUTER or VIDEO button on the remote control. * Press the MENU button on the remote control to display the Viewer menu. Press the MENU button again to

display the main menu and select the input from the [Source] submenu.

With this function it is possible to switch directly to a slide when the picture of a VCR or computer is being projected. Example: When conducting presentations using a combination of slides and moving pictures from a VCR, etc., it is possible to switch from a Viewer slide to the video picture then back to the Viewer slide simply by using the Viewer button.

NOTE: Even if you switch the current Viewer source to another source, the current slide is retained. When you return back to the Viewer, you will get the slide that has been retained.

Viewing Digital Images

Digital images can be played with the Viewer if the following conditions are met:

• If the image can be stored on an MS-DOS format PC card.

• If the image can be stored in a format supported by the Viewer. With the Viewer, images on the card are

searched for in directories and images in JPEG, BMP, non-interlaced GIF or non-interlaced PNG format are recognized as slides.

NOTE: The maximum number of images recognized as slides within one directory is about 1000.

Page 84

5. Using the Viewer

Deleting Captured Images

Using the Delete command on the Viewer menu allows you to delete captured images.

To delete captured images:

Preparation: Make sure that the PC card is inserted into the PC card slot or USB memory into the USB port of the projector.

1. Press the VIEWER button on the remote control to display an image.

2. Press the MENU button to display the Viewer menu.

3. Use the 왔 button to select “Thumbnails” and then press the ENTER button.

The Thumbnail screen will be displayed.

Slot 1

_CAP_ _RESTORE RECYCLED

1/3 0000.jpg 60KB

3 Files

0000.jpg 0001.jpg 0002.jpg

select : ENTER

folder :

EXIT

NOTE: To change highlight from the Thumbnails screen (pane on the right) to a directory tree (pane on the left) , press the EXIT button. To return highlight to the Thumbnails screen, press the ENTER button.

4. Use the SELECT

왖왔왗 or 왘

button to select an image you wish to delete.

5. Press the MENU button to display the Viewer menu.

6. Use the SELECT 왔 button to select “Delete” and then press the ENTER button.

A confirmation message will be displayed.

7. Use the SELECT 왗 button to select “Yes” and then press the ENTER button.

This completes deleting.

Page 85

5. Using the Viewer

To delete all the captured images:

1. Repeat steps 1 to 3 in the above described procedure.

2. Press the EXIT button to select the “__CAP__” folder in the directory (pane on the left).

Slot 1

__CAP__ _RESTORE RECYCLED

1/3 0000.jpg 60KB

3 Files

0000.jpg 0001.jpg 0002.jpg

select : ENTER folder : EXIT

3. Press the MENU button to display the Viewer menu.

4. Use the

왔

button to select “Delete” and then press the ENTER button.

A confirmation message will be displayed.

5. Use the

왗

button to select “Yes” and then press the ENTER button.

This completes deleting.

NOTE: The vacant "__CAP__" folder stays even after you delete all the captured images.

Page 86

5. Using the Viewer

 Changing Background Logo

You can change the default background logo using the Viewer feature.

NOTE: File size must be 256KB or less. File formats other than JPEG, BMP, non-interlaced GIF or non-interlaced PNG are not available.

Preparation:

Use the Capture feature to store JPEG or BMP files in a PC card inserted into the projector’s slot or USB memory* into projector’s USB port. Or store JPEG, BMP, non-interlaced GIF or non-interlaced PNG files in a PC card or USB memory inserted into your PC’s slot or USB port and insert the PC card into the projector’s slot or USB memory into the projector’s USB port.

*NOTE: USB memory devices are not available for the Capture function on the WT610.

1. Press the VIEWER button on the remote control to display an image.

2. Press the MENU button to display the Viewer menu.

3. Use the SELECT 왔 button to select “Thumbnails” and then press the ENTER button.

The Thumbnail screen will be displayed.

Slot 1

_CAP_ _RESTORE RECYCLED

1/3 0000.jpg 60KB

3 Files

0000.jpg 0001.jpg 0002.jpg

select : ENTER

folder :

EXIT

4. Use SELECT

왖왔왗

or 왘 button to select a file (slide) for your background logo.

5. Press the MENU button to display the Viewer menu.

6. Use the SELECT 왔 button to select "Logo" and then press the ENTER button.

A confirmation dialog box will be displayed.

7. Use the SELECT 왗 button to select “Yes” and press the ENTER button. This completes changing a logo

for the background.

* Once you have changed the background from the NEC logo to another, you cannot return the logo to back-

ground even by using “Reset”. To put the NEC logo back in the background logo, repeat the above steps. The NEC logo file is included on the supplied User Supportware 2 CD-ROM (/Logo/nec_b_x.jpg).

Page 87

Using On-Screen Menu

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 Using the Menus........................................................ 81

 Menu tree .................................................................. 82

 Menu Elements.......................................................... 84

 Menu Descriptions & Functions [Source] .................. 85

 Menu Descriptions & Functions [Adjust] .................... 88

 Menu Descriptions & Functions [Setup] .................... 98

 Menu Descriptions & Functions [Information] .......... 126

 Menu Descriptions & Functions [Reset] .................. 129

Page 88

6. Using On-Screen Menu

 Using the Menus

1. Press the MENU button on the remote control or the projector cabinet to display the menu.

Submenu

NOTE: The commands such as ENTER and EXIT in the gray bar show available buttons for your operation.

2. Press the SELECT

submenu.

3. Press the ENTER button on the remote control or the projector cabinet to select the top item or the first

tab.

4. Use the SELECT

want to adjust or set.

You can use the SELECT 왗 or 왘 button on the remote control or the projector cabinet to select the tab you want.

NOTE: You can select a tab only when the tab color is orange.

왗

or 왘 buttons on the remote control or the projector cabinet to display the

왖

or 왔 buttons on the remote control or the projector cabinet to select the item you

Submenu window

Main menu

Currently available buttons

5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.

6. Adjust the level or turn the selected item on or off by using the SELECT

control or the projector cabinet.

Changes are stored until that particular function is adjusted again.

7. Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the

projector cabinet to quit the menu display.

NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.

왖왔왗

or 왘 button on the remote

Page 89

6. Using On-Screen Menu

 Menu tree

Menu Item

Source Computer, DVI (DIGITAL), DVI (ANALOG), Video, S-Video, Viewer, LAN, Test Pattern, Entry List Adjust Basic Brightness

Contrast

Color

Hue

Sharpness

Wall Color Off, Blackboard, Blackboard (Gray), Light yellow, Light green, Light blue, Sky blue,

Light rose, Pink

Aspect Ratio 4:3 4:3, Letterbox, Wide Screen, Crop

16:9 4:3 Window, Letterbox, Wide Screen, 4:3 Fill Volume Reset

Picture Preset 1 to 5 Management Detail Settings Reference Presentation, Video, Movie,

Gamma Correction Color Temperature White Peaking White Balance Brightness RGB, Contrast RGB Color Correction Red, Green, Blue,Yellow, Magenta,

Signal Type RGB, Component Video Filter Off, Less, More

Image Options Clock

Phase Horizontal Position Vertical Position Blanking Top, Bottom, Left, Right Resolution Auto, Native Overscan 0%, 5%, 10%

Video Noise Reduction Off, Low, Medium, High

Color Matrix HDTV, SDTV I/P Converter Deinterlace(Auto/Still), Interlace

Setup Basic Pen Calibration (WT615 only)

Tilt Indicator Pincushion Left/Right, Top, Bottom Cornerstone Keystone Horizontal, Vertical Lamp mode Normal, Eco Menu Mode Basic Menu, Advanced Menu Language English, Deutsch, Français, Italiano, Español, Svenska, Suomi, Norsk,

Nederlands, Türkçe, Polski, , , Magyar, Português,

, , Dansk, , ,

estin

Menu Menu Color Select Color1 to 5, Monochrome

Display Select Source: On, Off / Message: On, Off Menu Display Time Manual, Auto 5 sec, Auto 15 sec, Auto 45 sec Background Blue, Black, Logo

Basic menu items are indicated by shaded area.

Graphic, sRGB Dynamic, Natural, Black Detail 5000, 6500, 7800, 8500, 9300, 10500

Cyan, Color Gain

Page 90

6. Using On-Screen Menu

Menu Item

Setup Security Security Cabinet Button Unlock, Lock

Password (Menu) Entry, Delete Password (Logo) Entry, Delete Security Enable, Disable, Keyword, Use Protect Key, Drive, Read, Register, Delete

Installation Orientation Desktop Front, Ceiling Rear, Desktop Rear, Ceiling Front

Screen Screen Type: 4:3, 16:9 / Position LAN Mode Profile

Domain Host Name, Domain Name

Mail Alert Mail, Sender’s Address, SMTP Server Name,

Projector Name Communication Speed 4800, 9600, 19200, 38400 bps Standby Mode Normal, Power-saving

Options Auto Adjust Off, Normal, Fine

Auto Start Off, On Power Management Off, 0:05, 0:10, 0:20, 0:30 Fan Mode Auto, High Default Source Select Last, Auto, Select (Computer, DVI (DIGITAL/ANALOG), Video, S-Video, Viewer, LAN) Signal Select Computer RGB/Component, RGB, Componet, Scart

DVI (ANALOG) RGB/Component, RGB, Componet

Video Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM

S-Video Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM OUT Terminal Last, Computer, DVI (ANALOG)

Tools ChalkBoard

Board Color Transparent, Dark Gray, Light Gray, Dark Cyan, Blue, Black Digital Zoom Zoom, Horizontal Position, Vertical Position Off Timer Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00 Mouse Mouse Pointer: Pointer 1 to 9 / Button: Right Hand, Left Hand /

Sensitivity: Fast, Medium, Slow Pointer Pointer 1 to 9 Closed Caption Off, Caption 1-4, Text 1-4

Information Usage Time Remaining Lamp Time, Lamp Hour Meter, Projector Usage

Source Page1 Input Terminal, Signal Type, Video Type, Source Name, Entry No. Source Page2 Horizontal Frequency, Vertical Frequency, Sync Type, Sync Polarity, Interlace LAN Profile IP Address, Subnet Mask, Gateway, MAC Address LAN Wireless SSID, Mode, WEP, Channel, Signal Level Version Firmware, Data

Reset Current Signal, All Data, All Data (Including Entry List), Clear Lamp Hour Meter

Profiles, DHCP, IP Address, Subnet Mask, Gateway, DNS Configuration, Advanced: Network Type, Wep

Recipient’s Address 1-3

Page 91

 Menu Elements

Highlight

Ta b

6. Using On-Screen Menu

Slider

Close button

Radio button

Check box

OK button

Menu windows or dialog boxes typically have the following elements:

Highlight................ Indicates the selected menu or item.

Solid triangle ......... Indicates further choices are available. A highlighted triangle indicates the item is active.

Tab ........................ Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.

Radio button ......... Use this round button to select an option in a dialog box.

Check box ............. Place a checkmark in the square box to turn the option On.

Slider ..................... Indicates settings or the direction of adjustment.

OK button .............. Press to confirm your setting. You will return to the previous menu.

Cancel button ........ Press to cancel your setting. You will return to the previous menu.

Close button .......... Click to close the window and saving changes. (USB mouse only)

Help button ........... Indicates that help about that feature is available (USB mouse only).

Cancel button

Help button

Solid triangle

Page 92

6. Using On-Screen Menu

쐏 Menu Descriptions & Functions [Source]

Computer

Selects the computer connected to your Computer input connector signal.

NOTE: An optional component cable (Component V or ADP-CV1 cable) is needed for a component signal.

DVI (DIGITAL/ANALOG)

Selects the computer connected to the DVI input connector.

Video

Selects what is connected to your Video input-VCR, laser disc player, DVD player or document camera.

S-Video

Selects what is connected to your S-Video input-VCR, DVD player, or laser disc player.

NOTE: A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with a Video or SVideo source.

Viewer

This feature enables you to make presentations using a PC card that contains captured images and slides created with the exclusive Photo Explore 8.0 for NEC contained on the CD-ROM. See the supplied “Wired and Wireless Network Setup Guide” for installing the Photo Explore 8.0 for NEC. See page 71 for viewing slides.

LAN

Selects a signal from the NEC optional wireless LAN card or a commercially available wired LAN card plugged into the projector's card slot.

Test Pattern

Displays a test pattern to check your adjustments or image position.

NOTE:

• Select “Computer” for your source signal even when the COMPUTER IN connector is connected to a component signal.

• When you select “Viewer” or “LAN” for your source signal, sound of the DVI-I AUDIO IN mini jack will come from the speaker.

Page 93

6. Using On-Screen Menu

Entry List

Use the SELECT 왖 or 왔 button on your remote control or the projector cabinet to select the signal and press the ENTER button on the remote control or the projector cabinet to display the Entry Edit Command screen.

Entering the Currently Projected Signal into the Entry List

1. Display the Entry List.

2. Use the SELECT press the ENTER button on the remote control or the projector cabinet to display the Entry Edit Command screen.

3. Use the SELECT

왖

or 왔 button on your remote control or the projector cabinet to select any number and

왗

or 왘 button to select [Store] and press the ENTER button.

Using the Entry List

Making any adjustments to the current picture will automatically register its adjustments to the Entry List. The registered signal can be loaded any time from the Entry List.

NOTE: Up to 100 presets can be registered except settings on the Picture.

Page 94

6. Using On-Screen Menu

Entry Edit Command

You can edit signals on the Entry List.

Load ...................... Enables you to select a signal from the list.

Store ..................... Enables you to store the currently projected signal.

Cut ........................ Enables you to remove a selected signal from the list and place it on the "clipboard" in the projector.

Copy ...................... Enables you to copy a selected signal from the list and place it on the "clipboard" in the projector.

Paste ..................... Enables you to paste the signal placed on the "clipboard" to any other line of the list.

Edit ........................ Enables you to change source names.

Source Name:

Enter a signal name. Up to 18 alphanumeric characters can be used.

Input Terminal:

Change the input terminal.

Lock:

Set so that the selected signal cannot be deleted when "All Delete" is executed. After executing “Lock”, the changes cannot be saved.

Skip:

Set so that the selected signal will be skipped during auto search. When complete, select “OK” and press ENTER. To exit without storing the setting, select Cancel. Select

"Source Name" and press ENTER to display the Source Name Edit window. You can change source name on this window. Press 왔 to display the software keyboard, which you can enter alphanumeric characters. See page 148 for the key function of the software keyboard.

All Delete ............... This feature enables you to delete all the registered signals in the Entry List.

The following buttons are not available for the currently projecting signals:

1) The Cut and Paste buttons on the Entry Edit Command screen

2) The Input Terminal button on the Entry Edit screen

NOTE: When all the signals in the Entry List are deleted, the currently projected signal will be also deleted except locked signals.

Page 95

쐄 Menu Descriptions & Functions [Adjust]

Basic

6. Using On-Screen Menu

[Brightness]

Adjusts the brightness level or the back raster intensity.

[Contrast]

Adjusts the intensity of the image according to the incoming signal.

[Color]

Increases or decreases the color saturation level (not valid for RGB and DVI digital).

Page 96

6. Using On-Screen Menu

[Hue]

Varies the color level from +/- green to +/-blue. The red level is used as reference. This adjustment is only valid for Video, Component and TV standard inputs (not valid for RGB and DVI digital).

[Sharpness]

Controls the detail of the image for Video (not valid for RGB and DVI digital).

Using the Wall Color Correction [Wall Color]

This function allows for quick adaptive color correction in applications where the screen material is not white. The following nine options are available.

• OFF • Blackboard

• Blackboard (Gray) • Light yellow

• Light green • Light blue

• Sky blue • Light rose

• Pink

Page 97

6. Using On-Screen Menu

Selecting Aspect Ratio [Aspect Ratio] (not available for Viewer)

Screen Type 4:3 Screen Type 16:9

Aspect Ratio allows you to select the best Aspect mode to display your source image. When screen type 4:3 is selected for the source, the following selections will display:

4:3 .........................Standard 4:3 aspect

Letter Box .............. Reduced to display the true aspect with black borders on top and bottom

Wide Screen .......... Left & Right stretched with black borders on top and bottom

Crop ...................... Left & Right stretched. Left & Right sides cut. Available for 4:3 only.

When screen type 16:9 is selected for the source, the following selections will display:

4:3 Window ........... Reduced to display the true aspect with black borders on right and left

Letter Box .............. Standard 16:9 aspect

Wide Screen .......... Left and right stretched to display the true aspect

4:3 Fill ................... Stretched to display in 16:9 aspect ratio

NOTE: You can adjust image position vertically for a source with black borders on top and bottom. See page 110 for setting image position. Copyright Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with a "Aspect Ratio" or "Screen" setting may raise concern about the infringement of copyrights which are protected by copyright law.

NOTE: During 3D Reform adjustment, "Aspect Ratio" may not be available. Should this happen, first reset the 3D Reform data and then do setting again. Second repeat the 3D Reform adjustment. Changing the aspect ratio can limit 3D Reform in its adjustable range.

Input Signal

Screen Type

4:3 Screen

16:9 Screen

4:3 Window

4:3

4:3 Letterbox

4:3 Fill

Letterbox

Squeeze

Wide Screen

Crop

Page 98

6. Using On-Screen Menu

Controlling Volume [Volume]

You can adjust the volume level of the projector speakers and AUDIO OUT (Stereo Mini Jack).

Reset

To reset the settings for “Basic”, select “Reset” and press the ENTER button. The message "The setting values on page will be reset. Are you sure?” will be displayed. Select “Yes” and press the ENTER button. To return without storing settings, select “No” and press the ENTER button.

Picture Management

[Preset]

This option allows you to adjust neutral tint for yellow, cyan or magenta. There are 5 factory presets optimized for various types of images, you can set user adjustable settings.

Page 99

[Detail Settings]

This will provide you with three pages of menus that provide more detailed settings.

[Page1]

6. Using On-Screen Menu

Selecting Reference Setting [Reference] This feature allows you to use color correction or gamma values as reference data to optimize for various types of images. You can select one of the following five settings.

Presentation ...... Recommended for making a presentation using a PowerPoint file.

Video ................. Recommended for regular picture such as TV program.

Movie ................ Recommended for movies.

Graphic .............. Recommended for graphics.

sRGB ................. Standard color values.

Selecting Gamma Correction Mode [Gamma Correction]

Each mode is recommended for:

Dynamic ............ Creates a high-contrast picture.

Natural ............... Natural reproduction of the picture.

Black Detail ........ Emphasizes detail in dark areas of the picture.

Page 100

6. Using On-Screen Menu

Adjusting Color Temperature [Color Temperature]

This feature adjusts the color temperature using the slider.

NOTE: * When "Presentation" is selected in [Reference], this function is not available. * When [White Balance] settings has been changed, the color temperature value on screen does not reflect the real color

temperature.

Adjusting Brightness of White Area [White Peaking]

Adjust the brightness of the white areas by using the slide bar. As the picture becomes dim, it looks more natural.

[Page 2]

Adjusting White Balance [White Balance]

This allows you to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the screen; Contrast for each color (RGB) to adjust the white level of the screen.

[Page 3]

Selecting Color Correction [Color Correction]

Adjusts red, green, blue, yellow, magenta and cyan each independently to correct the tint of the whole screen.

NOTE: When "Presentation" is selected in [Reference], this function is not available.

Nec VT610 user Manual

Specifications and Main Features

Frequently Asked Questions

User Manual