MOTOROLA MC10EL35, MC100EL35 Technical data

MOTOROLA

SEMICONDUCTOR TECHNICAL DATA

3–1

REV 2

 Motorola, Inc. 1996

12/93

JK FlipĆFlop

The MC10EL/100EL35 is a high speed JK flip-flop. The J/K data enters
the master portion of the flip-flop when the clock is LOW and is
transferred to the slave, and thus the outputs, upon a positive transition of
the clock. The reset pin is asynchronous and is activated with a logic
HIGH.

• 525ps Propagation Delay

• 2.2GHz Toggle Frequency

• High Bandwidth Output Transitions

• 75kΩ Internal Input Pulldown Resistors

• >1000V ESD Protection

1

2

3

4 5

6

78Q

V

EE

V

CC

LOGIC DIAGRAM AND PINOUT ASSIGNMENT

K

Q

CLK

R

K

R

J

J

MC10EL35

MC100EL35

J

L

L
H
H
X

TRUTH TABLE

K

L

H

L
H
X

R

L
L
L
L

H

CLK

Z
Z
Z
Z
X

Qn+1

Qn

L

H

Qn

L

Z = LOW to HIGH Transition

1

8

D SUFFIX

PLASTIC SOIC PACKAGE

CASE 751-05

MC10EL35 MC100EL35

MOTOROLA ECLinPS and ECLinPS Lite

DL140 — Rev 3

3–2

DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)

–40°C 0°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit

I

EE

Power Supply 10EL
Current 100EL

272732

32

272732

32

272732

32

27323237mA

V

EE

Power Supply 10EL
Voltage 100EL

–5.2
–4.5

–4.75
–4.20

–5.2
–4.5

–5.5
–5.5

–4.75
–4.20

–5.2
–4.5

–5.5
–5.5

–4.75
–4.20

–5.2
–4.5

–5.5
–5.5

V

I

IH

Input HIGH Current 150 150 150 150 µA

AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)

–40°C 0°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit

f

MAX

Maximum Toggle
Frequency

1.4 2.0 1.8 2.2 1.8 2.2 1.8 2.2 GHz

t

PLH

t

PHL

Propagation Delay CLK
to Output MR

290
225

515
450

740
675

340
275

515
450

690
625

350
275

525
450

700
625

395
350

570
525

745
700

ps

t

S

Setup Time J, K 150 0 150 0 150 0 150 0 ps

t

H

Hold Time J, K 250 100 250 100 250 100 250 100 ps

t

RR

Reset Recovery 400 200 400 200 400 200 400 200 ps

t

PW

Minimum Pulse Width

CLK, Reset

400 400 400 400 ps

t

r

t

f

Output Rise/Fall Times Q
(20% – 80%)

100 225 350 100 225 350 100 225 350 100 225 350 ps

MC10EL35 MC100EL35

3–3 MOTOROLAECLinPS and ECLinPS Lite

DL140 — Rev 3

OUTLINE DIMENSIONS

D SUFFIX

PLASTIC SOIC PACKAGE

CASE 751–05

ISSUE P

SEATING
PLANE

1

4

58

C

K

4X P

A0.25 (0.010)MT B

S S

0.25 (0.010)

M

B

M

8X D

R

M

J

X 45

_

_

F

–A–

–B–

–T–

DIM MIN MAX

MILLIMETERS

A 4.80 5.00
B 3.80 4.00
C 1.35 1.75
D 0.35 0.49

F 0.40 1.25
G 1.27 BSC
J 0.18 0.25
K 0.10 0.25
M 0 7
P 5.80 6.20
R 0.25 0.50

__

G

NOTES:

1. DIMENSIONS A AND B ARE DATUMS AND T IS A
DATUM SURFACE.

2. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

3. DIMENSIONS ARE IN MILLIMETER.

4. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.

5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

6. DIMENSION D DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE D DIMENSION AT MAXIMUM MATERIAL
CONDITION.

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability , including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: [e-mail] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

MC10EL35/D

*MC10EL35/D*

◊

WWW.ALLDATASHEET.COM

Copyright © Each Manufacturing Company.

All Datasheets cannot be modified without permission.

This datasheet has been download from :

www.AllDataSheet.com

100% Free DataSheet Search Site.

Free Download.

No Register.

Fast Search System.

www.AllDataSheet.com