4Hz to 22,000Hz (48kHz Sampling, Linear Audio)
4Hz to 44,000Hz (96kHz Sampling, Linear Audio)
Audio Frequency Response (DVD-Audio)
4Hz to 88,000Hz (192kHz Sampling)
CD Frequency Response
4Hz to 20,000Hz
CD Signal to Noise Ratio
Better than 100dB (A-weighted)
Dynamic Range (DVD)
Better than 100dB (Linear Audio)
General Specifications
Digital Output
Optical:-15dbm to –21dbm
Coaxial:0.5V p-p/75 ohm
Digital Signal Format
Sampling Frequencies: 44,100Hz, 48,000Hz and 96,000Hz
T ransport
Laser Beam W avelength: 658nm/790nm
Laser Power: CLASS IIa/ CLASS I
Power Requirements
100 Volts, 50/60Hz at 30 watts
110 Volts, 50/60Hz at 30 watts
120 Volts, 50/60Hz at 30 watts
220 Volts, 50/60Hz at 30 watts
230 Volts, 50/60Hz at 30 watts
240 Volts, 50/60Hz at 30 watts
Note : Refer to the rear panel of the MVP851 for the correct voltage.
Overall Dimensions
Front Panel: 17-1/2 inches (44.5cm) wide, 5-3/8 inches (13.7cm)
high. Depth behind front mounting panel is 15 inches (38.1cm)
including clearance for connectors. Panel clearance required in
front of mounting panel is 3/4 inch (1.9cm).
Dynamic Range (CD)
Better than 98dB
Harmonic Distortion
0.003% (1,000Hz)
Channel Separation
Better than 110dB (1,000Hz)
Video Specifications
Signal System
NTSC
Component Video Output Level
Y Output Level 1.0Vp-p (75 ohm)
Output Level 0.7Vp-p (75 ohm)
P
B
Output Level 0.7Vp-p (75 ohm)
P
R
S-Video Y Output Level
1Vp-p (75 ohm)
S-Video C Output Level
0.286Vp-p (75 ohm) (NTSC)
Video Output Level
1Vp-p (75 ohm)
Note : When the DVD/CD tray is opened, the panel clearance
required in front of mounting panel is 6-3/4 inches (17.2cm).
Weight
20 pounds (9.1kg) net, 34 pounds (15.4kg) in shipping carton
2
Page 3
NO TES
MVP851
1. The heavy notes on the schematic denote the primary
signal path.
2. Unless otherwise noted, all voltages indicated on the
schematics are measured under the following conditions:
a. AC input at 120 volts, 50/60Hz.
b. All voltages are +/-10% with respect to ground. A
high impedance (10 megaohm) voltmeter must be used.
3 . Unless otherwise specified:
a. Resistor values are in ohms.
b. Capacitor values are microfarads (uF).
c. Inductor values are in microhenries (uH).
4 . On PC board drawings, Square pad indicates:
a. Polarized Capacitors - Positive
b. Diodes - Cathode
c. Others - Pin 1
5. WARNING
Parts marked with the symbol have critical
characteristics. Use only replacement parts recommended by the manufacturer.
6 . Use McIntosh Remote Control Model HR040 with the
MVP851.
SAFETY INFORMATION
CAUTION:The use of optical instruments with this
product will increase eye hazard.
This product utilizes a Class I laser. Invisible laser
radiation is emitted from the optical pickup lens when the
unit is turned on.
1 . Do not look directly into the pickup lens.
2. Do not use optical instruments to look at the pickup
lens.
3. Do not adjust the preset variable resistor on the
optical pickup.
4 . Do not disassemble the optical pickup unit.
5 . Use of controls or adjustment or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
6 . Replace optical pickup only with manufacturers
specified type.
Laser output: CLASS IIa / CLASS I
Wavelength:658nm / 790nm
This product utilizes an embedded Class IIa laser (IEC825).
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
VAROITUS! Laitteen kayttaminen muulla kuin tassa
kayttoohjeessa mainitulla tavalla saattaa altistaa
kayttajan turvallisuusluokan 1 ylittavalle
nakymattomalle lasersateiiylle.
VARNING! Om apparaten anvands pa annat satt an
i denna bruksanvisning specificerats, kan anvandaren
utsattas for osynbg laserstraining, som overskrider
gransen for laserklass 1.
1016482GLASS
2017531PUSHBUTTON ASSY RED
3017517PUSHBUTTON ASSY BLK
4078033O-RING
5148073SWITCH DPDT ROCKER
6017781 BEZEL FRONT
7092419FILTER DISPLA Y
No.
DescriptionRef
8094016TAPE FOAM 1/4 X 1/8
9098113CORD DIAL .027 BLACK BRAID SILK
10018706 EXTRUSION BOTTOM
11100147 SCREW MACH 6-32 X 3/16 PHIL
12018585 EXTRUSION TOP
13017906 GUIDE PCB
14094360 TAPE FOAM 1/2 X 1/2
15094017 TAPE FOAM 1/4 X 1/4
16005090 BRACKET EXTRUSION
17018611 ENDCAP 5”
18101042 SCREW TS 4-40 X 1/2 SLOT FILLISTER
19049774 ASSY PCB DISPLA Y
20017901 LOGO PUSHBUTTON BACKLIGHT
21017902 SUPPORT PCB LOCKING ADHESIVE BASE
22005258 SUBP ANEL
23101196 SCREW T AP SEMS 6-32 X 1/4 PH PN
24101054 SCREW T APTITE 6-32 X 1/4 PH PN BLK
25005261 BRACKET RIGHT ZEE
26005260 BRACKET LEFT ZEE
27102003 NUT MACH 6-32 W/LOCK
28320119 DVD MECHANISM
29017900 DOOR MOLDING MVP851
30100271 SCREW MACH 6-32 X 1/4 PH PN
31100300 SCREW MACH SEMS 6-32 X 1 PH PN
32104005 WASHER FLAT STEEL 6 X 3/8 X .032
33005257 CHASSIS
34019056 SPRING
35100180 SCREW MACH 6-32 X 1/8 PH PN
36049773 ASSY PCB AV -PWR
37320118 ASSY PCB DVD MODULE
38101222 SCREW TT SEMS 6-32 X 1/4 PH PN
39005262 BRACKET CABLE
40159334 TRANSFORMER R-CORE POWER
41117800 MTA CONNECTOR 8 PIN .156
42112083 STANDOFF 6-32 X 1.250
43005259 REAR PANEL
44117755 RECEPTACLE INPUT & LINE FIL TER
45102001 NUT KEP 4-40 CADMIUM PLA TE
46102020 NUT MACH 6-32 SELF LOCK
47101197 SCREW HI-LO 4-24 X 3/8 PH RD BLK
48017218 FOOT PLASTIC BLACK
49104083 WASHER #10 PLATED 104062
50100159 SCREW MACH 10-32 X 3/4 PH PN BLK
51005102 COVER TOP
52101078 SCREW T AP 8-32 X 5/16 PH PN BLK
2423
Page 16
REPACKING INSTRUCTIONS
DVD AUDIO/VIDEO PLAYER
SERVICE MANUAL
25
The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated, who reserve the right to improve design without
notice. Because of the constant upgrading of McIntosh products’ circuitry and components, the Company cannot insure, and does not warrant, the
accuracy of the within schematic material, which is intended for information only.
McINTOSH LABORATORY, INC., 2 CHAMBERS STREET, BINGHAMTON, NEW YORK 13903 Printed in U.S.A. Part Number 040863
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.