Use & Care Guide
Guide d’utilisation et d’entretien
FRONT-LOADING AUTOMATIC WASHER
LAVEUSE AUTOMATIQUE À CHARGEMENT FRONTAL
Para obtener acceso
al Manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.maytag.com
W11156983B W11156984A – SP
If you have any problems or questions, visit us at www.maytag.com
Pour tout problème ou toute question, consulter le www.maytag.ca
Designed to use only HE High Efficiency detergents.
Conçue uniquement pour une utilisation avec des détergents HE Haute efficacité.
Protocole NSF P351
Performance de réduction des allergènes pour les laveuses de format familial à usage résidentiel ou commercial Seuls les modèles comportant le programme de lavage anti-allergie répondent aux critères de la certification NSF.
TABLE OF CONTENTS / TABLE DES MATIÈRES
WASHER SAFETY...................................................................................................... |
|
3 |
ACCESSORIES............................................................................................................ |
|
4 |
CONTROL PANEL AND FEATURES....................................................................... |
|
5 |
CYCLE GUIDE.............................................................................................................. |
|
8 |
CHOOSING THE RIGHT DETERGENT................................................................. |
|
10 |
USING THE OPTIMAL DISPENSE DRAWER (on some models) |
..................10 |
|
USING YOUR WASHER.......................................................................................... |
|
11 |
WASHER MAINTENANCE...................................................................................... |
|
16 |
TROUBLESHOOTING............................................................................................... |
|
20 |
WARRANTY................................................................................................................ |
|
29 |
ASSISTANCE OR SERVICE............................................................. |
BACK COVER |
SÉCURITÉ DE LA LAVEUSE................................................................................... |
|
30 |
ACCESSOIRES.......................................................................................................... |
|
31 |
TABLEAU DE COMMANDE ET CARACTÉRISTIQUES..................................... |
32 |
|
GUIDE DE PROGRAMMES.................................................................................... |
|
36 |
CHOIX DU DÉTERGENT APPROPRIÉ................................................................. |
|
40 |
UTILISATION DU TIROIR DISTRIBUTEUR DE DOSAGE OPTIMAL |
|
|
(sur certains modèles)............................................................................................ |
|
40 |
UTILISATION DE LA LAVEUSE.............................................................................. |
|
41 |
ENTRETIEN DE LA LAVEUSE................................................................................. |
|
46 |
DÉPANNAGE.............................................................................................................. |
|
51 |
GARANTIE................................................................................................................... |
|
63 |
ASSISTANCE OU DÉPANNAGE.................................. |
COUVERTURE ARRIÈRE |
2
3
INSTALLATION & MAINTENANCE
ACCESSORIES
FACTORY CERTIFIED PARTS – these three words represent quality parts and accessories designed specifically for your appliance.
Time tested engineering that meets our strict quality specifications.
FACTORY CERTIFIED PARTS
Accessories designed for your appliance:
Customize your new washer and dryer with the following genuine Whirlpool accessories. For more information on options and ordering, call 1-800-344-1274 or visit us at: www.maytag.com/accessories. In Canada, call 1-800-688-2002 or visit us at www.maytag.ca.
15" Pedestal
Color-matched pedestals raise the washer and dryer to a more comfortable working height.
The large drawer provides convenient storage.
Stack Kit
If space is at a premium, the stack kit allows the dryer to be installed on top of the washer.
4
Not all features and cycles are available on all models.
NOTES:
■■The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered, touch the control panel with your fingertip, not your fingernail. When selecting a setting or option, simply touch its name.
■■At cycle completion, your setting and option choices will be remembered for your next use of that cycle. However, if power is lost to the washer, the settings and options will go back to the factory defaults.
2 |
4 |
5 |
1 |
|
|
|
A |
|
|
D |
|
|
F |
|
B |
E |
|
I |
|
|
6 |
6 |
3 |
2 |
4 |
5 |
1 |
|
|
|
A |
|
|
|
|
D |
|
|
|
|
F |
|
C |
|
E |
B |
|
I |
|
|
|
|
|
|
6 |
6 |
3 |
2 |
4 |
5 |
|
1 |
A
D
H
C G B
I
6 |
6 |
3 |
5
1POWER
Touch to turn the washer on and off. Touch to stop/cancel a cycle at any time.
NOTE: Turning the Wash Cycle knob will also turn the washer on.
2WASH CYCLE KNOB
Turn the knob to select a cycle for your laundry load. Press the Wash Cycle knob to enable the Extra Power option.
NOTE: The Clean Washer with affresh® LED will flash when the washer has run 30 wash cycles as a reminder to run the Clean Washer with affresh® cycle.
See “Cycle Guide” for detailed descriptions of cycles.
NOTE: For best results when using the Overnight Wash & Dry cycle, use for loads weighing 2 lbs or less, such as a soccer uniform or a running tank and shorts. Allow the cycle to run the full duration of 12 hours.
EXTRA POWER
Extra Power option can be used for increased cleaning power. Press the Wash Cycle Knob to activate the Extra Power option, which runs a cold pre-wash cycle before the main cycle. When Extra Power is activated, the Cycle Control Knob will illuminate and the estimated time remaining on the display will increase. On single load dispenser models, add an extra dose of detergent to the
Bleach/Detergent for Extra Power compartment when using Extra Power, for best results.
3START
Touch and hold for 3 seconds until the light above START comes on to start a cycle or touch once while a cycle is in process to pause it. If you want to add a garment, you can touch START when the “Add Garment” LED is on.
4LED DISPLAY AND SETTINGS
When you select a cycle, its default settings will light up and the Estimated Time Remaining will be displayed. Factors such as load size, wash temperature, and water pressure may affect the time shown in the display. Tightly packing, unbalanced loads, or excessive suds may cause the washer to lengthen the cycle time as well.
Touch the desired setting on the display to adjust. See “Cycle Guide” for available settings on each cycle. Not all settings are available with all cycles.
Temp
The recommended wash temperature is preset for each cycle. You may also select a wash temperature based on the type of fabric and soils being washed. For best results, use the warmest wash water safe for your fabric, following the garment label instructions. All wash temperatures feature a cold rinse.
Spin
This washer automatically selects the spin speed based on the cycle selected. Some preset speeds can be changed.
■■Faster spin speeds mean shorter dry times but may increase wrinkling in your load.
■■Slower spin speeds reduce wrinkling but will leave your load more damp.
Soil
Soil Level (wash time) is preset for each wash cycle. When you change the soil setting, the cycle time will increase or decrease in the Estimated Cycle Time display.
For most loads, use the soil level that is preset with the cycle you have chosen. For heavily soiled and sturdy fabrics, use the Soil Level setting to select a higher soil level. For lightly soiled and delicate fabrics, use the Soil Level setting to select a lower soil level. Lower soil level settings will help reduce tangling and wrinkling.
5CYCLE STATUS LIGHTS
NOTE: Not all Cycle Status Lights are available on all models.
The Cycle Status Lights show the progress of a cycle. At each stage of the process, you may notice sounds or pauses that are different from traditional washers.
Sensing
When START is touched and held, the washer will first perform a self-test on the door lock mechanism and the sensing light will come on. You will hear a click, the drum will make a partial turn, and the door will click again as it unlocks briefly. The door will click one more time when it locks again.
Once the door has locked the second time, the washer will begin spinning to sense the load size. This sensing process will continue throughout the cycle. You may also hear water flowing through the dispenser, adding detergent to the load.
After the load size is sensed, the estimated time based on load size will be displayed. The actual cycle time may be lengthened; however, the display will continue to show the estimated time.
The sensing light will blink once a second at various times during the cycle, such as when the washer is reducing extra suds.
Washing
During the wash cycle, this will display to let you know the cycle is in progress.
Add Garment
When “Add Garment” is lit, you may pause the washer, open the door, and add items. Touch and hold START to start the washer again.
Detergent Low
When detergent in the dispenser is running low, the display will show the detergent level (Low).
6 OPTIONS
Touch to activate additional wash options or additional features on the washer. Not all options are available on all models.
ADelay Start
Touch this option to delay the start of the wash cycle by up to 12 hours.
6
BFresh Hold®/Fresh SpinTM
The Fresh Hold®/Fresh SpinTM option will periodically tumble the load after the end of the cycle for up to 24 hours while the integrated fan circulates air through the washer to reduce humidity. Fresh Spin™ also periodically tumbles the load after the end of the cycle but does not use an integrated fan. To turn on the Fresh Hold®/Fresh Spin™ option, touch FRESH HOLD. If, however, the Fresh Hold®/Fresh Spin™ option is turned on, it will stay on for all future cycles until turned back off – the washer remembers the last on/off status set. To turn off the Fresh Hold®/Fresh Spin™ option, touch FRESH HOLD.
To turn off the Fresh Hold®/Fresh Spin™ option when it is running, touch POWER.
NOTE: The door will lock while the Fresh Hold®/Fresh Spin™ option is active. To cancel the option and unlock the door, touch POWER.
CSteam
The Steam option adds additional soak and wash time to many cycles to help remove tough stains as well as a steam boost for added cleaning power. An integrated heater helps to maintain optimal wash temperatures.
DExtra Rinse
Activate this option to add an extra rinse to most cycles.
ECycle Signal
Touch and hold CYCLE SIGNAL for about 3 seconds the display will count down you will see “3,” then “2,” then “1.” The display will start displaying the sound levels you will see “1,” then “2,” then “3,” then “OFF.” When the CYCLE SIGNAL is released the last value shown will be the current selection.
7 DISPENSERS
Optimal Dispense Drawer (on some models)
The Optimal Dispense drawer gives you the convenience of automatically adding HE detergent, liquid chlorine bleach, and liquid fabric softener to the wash load at the proper time. See “Using the Optimal Dispense Drawer” for information on using the dispenser drawer.
C |
B |
A |
AOptimal Dispense Liquid High Efficiency “HE” detergent compartment
This compartment holds up to 14.3 oz (424 ml) of liquid HE detergent allowing you to avoid having to refill detergent for each load. Also, this will use just the right amount of detergent required for a particular load/cycle.
BLiquid fabric softener compartment
Automatically dilutes and dispenses liquid fabric softener at the optimum time in the cycle.
■■Use only liquid fabric softener in this dispenser.
Liquid chlorine bleach compartment
FControl Lock
Touch and hold for 3 seconds to lock the controls to avoid unwanted changes or operation. Touch and hold 3 seconds again to unlock. For each second CONTROL LOCK is held down, the display will count down 1 second; you will see “3,” then “2,” then “1.” You may still touch START to pause the cycle or touch POWER to turn off the washer.
GWiFi Connect
Download the Maytag™ app and follow the instructions to connect your washer/dryer to your home Wi-Fi network. You may also visit www.maytag.com/connect. In Canada, visit www.maytag.ca.
HRemote Enable
Touch this button to be able to use the Maytag® app to control the washer. Press this button each time after Power On and when the door is opened and closed.
IExtra Power
The Extra Power option boosts stain fighting performance on any wash cycle with a dual temperature wash, combining cold and hot temperature during different phases of the wash time. To use this function press the knob to activate the Extra Power option. For single dose dispensers and an additional 1/2 the manufacturer’s recommended amount into the dispenser marked for Extra Power. For the Optimal Dispenser it will automatically dispense the detergent at the optimal time.
Single Load Dispenser Drawer (on some models)
The dispenser drawer gives you the convenience of adding HE detergent, liquid chlorine bleach, and liquid fabric softener to the wash load at the proper time. See “Using the Dispenser Drawer” for information on using the dispenser drawer.
C
B
D
CAutomatically dilutes and dispenses liquid chlorine bleach at the optimum time during the first rinse after the wash cycle. This compartment cannot dilute powdered bleach. On single load dispenser models, use this compartment to add an extra dose of detergent when using the Extra Power option.
DLiquid High Efficiency “HE” detergent compartment
This compartment holds liquid or powdered HE detergent for your main wash cycle.
7
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings that best fit the load being washed. Not all settings are available with each cycle and some options cannot be used together.
Not all cycles and options are available on all models.
Load Size Recommendations
For best results, follow the load size recommendations noted for each cycle.
Small load: Fill the washer drum with 3–4 items, not more than ¼ full.
Medium load: Fill the washer drum up to about ½ full.
Large load: Fill the washer drum up to about ¾ full.
Extra-large load: Fill the washer drum, but make sure clothes can tumble freely. For best results, avoid packing tightly.
Items to wash |
Cycle: |
Wash |
Spin |
Soil |
Options/ |
Cycle Details: |
using default |
|
Temperature* |
Speed*** |
Level: |
Modifiers: |
|
cycle settings: |
|
|
|
|
|
|
Normally soiled |
Normal |
Cold |
Off |
Light |
Steam** |
This cycle combines |
cottons, linens, |
|
Cool |
Medium |
Medium |
Extra Rinse |
medium-speed tumbling |
sheets, and |
|
Warm |
Med Fast |
Med Heavy |
Fresh Hold®/Fresh |
and an extra-high- |
mixed garment |
|
Very Warm |
Fast |
Heavy |
Spin™ |
speed spin. This cycle is |
loads |
|
Hot |
|
|
Extra power |
designed to provide the |
|
|
|
most energy efficiency. |
|||
|
|
|
|
|
|
|
Sturdy colorfast |
Heavy |
Cold |
Off |
Light |
Steam** |
Fast-speed tumbling and |
fabrics and |
Duty |
Cool |
Slow |
Medium |
Extra Rinse |
an extra-fast-speed final |
heavily soiled |
|
Warm |
Medium |
Med Heavy |
Fresh Hold®/Fresh |
spin help provide optimal |
garments |
|
Very Warm |
Med Fast |
Heavy |
Spin™ |
cleaning and reduce |
|
|
Hot |
Fast |
|
Extra power |
drying times. |
|
|
|
|
|||
|
|
|
|
|
|
|
Heavily soiled |
Whites |
Cold |
Off |
Light |
Steam** |
Uses a longer wash |
white fabrics |
|
Cool |
Slow |
Medium |
Extra Rinse |
time with fast-speed |
and garments |
|
Warm |
Medium |
Med Heavy |
Fresh Hold®/Fresh |
tumbling, extra rinsing, |
|
|
Very Warm |
Med Fast |
Heavy |
Spin™ |
and an extra-fast-speed |
|
|
Hot |
Fast |
|
Extra power |
spin to provide optimal |
|
|
|
cleaning and rinsing |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
when bleach is used. |
|
|
|
|
|
|
|
Sturdy towels |
Towels |
Cold |
Off |
Light |
Steam** |
Provides fast-speed |
and wash cloths |
|
Cool |
Slow |
Medium |
Extra Rinse |
tumbling, longer wash |
|
|
Warm |
Medium |
Med Heavy |
Fresh Hold®/Fresh |
time, normal rinsing, |
|
|
Very Warm |
Med Fast |
Heavy |
Spin™ |
and an xtrafastspeed |
|
|
spin to shorten drying |
||||
|
|
Hot |
Fast |
|
Extra power |
|
|
|
|
time. |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Large items |
Bulky |
Cold |
Off |
Light |
Steam** |
Use this cycle to wash |
such as sleeping |
Items |
Cool |
Slow |
Medium |
Extra Rinse |
large items such as |
bags, small |
|
Warm |
Medium |
Med Heavy |
Fresh Hold®/Fresh |
jackets and small |
comforters, |
|
Very Warm |
Med Fast |
Heavy |
Spin™ |
comforters. The washer |
|
will fill with enough |
|||||
jackets |
|
Hot |
Fast |
|
Extra power |
|
|
|
water to wet down the |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
load before the wash |
|
|
|
|
|
|
portion of the cycle |
|
|
|
|
|
|
begins. |
|
|
|
|
|
|
Do not tightly pack |
|
|
|
|
|
|
basket. |
Small loads of |
Quick |
Cold |
Off |
Light |
Steam** |
For small loads (2–4 |
2–4 lightly soiled |
Wash |
Cool |
Slow |
Medium |
Extra Rinse |
items) needed quickly. |
garments |
|
Warm |
Medium |
Med Heavy |
Fresh Hold®/Fresh |
This cycle combines |
|
|
Very Warm |
Med Fast |
Heavy |
Spin™ |
fast-speed tumbling, a |
|
|
shortened wash time, |
||||
|
|
Hot |
Fast |
|
Extra power |
|
|
|
|
and an extra-fast- |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
speed spin for reduced |
|
|
|
|
|
|
drying times. |
|
|
|
|
|
|
Continued on next page |
*All temperature selections feature a Cold rinse.
**The Steam option is only available when a Warm, Very Warm, or Hot water temperature is selected.
***Spin speed varies by model.
8
Items to wash |
Cycle: |
Wash |
Spin |
Soil |
Options/ |
Cycle Details: |
using default |
|
Temperature* |
Speed*** |
Level: |
Modifiers: |
|
cycle settings: |
|
|
|
|
|
|
Sheer fabrics, |
Delicates |
Cold |
Off |
Light |
Steam** |
This cycle combines |
lingerie, |
|
Cool |
Slow |
Medium |
Extra Rinse |
slow-speed tumbling |
sweaters, and |
|
Warm |
Medium |
Med Heavy |
Fresh Hold®/Fresh |
and slow-speed spin |
lightly soiled |
|
Very Warm |
Med Fast |
Heavy |
Spin™ |
for gentle fabric care |
|
and reduced wrinkling. |
|||||
shirts, blouses, |
|
Hot |
Fast |
|
Extra power |
|
|
|
|
||||
trousers, pants, |
|
|
|
|
|
|
and skirts |
|
|
|
|
|
|
|
|
|
|
|
|
|
Lightly soiled |
Wrinkle |
Cold |
Off |
Light |
Steam** |
This cycle combines |
shirts, blouses, |
Control |
Cool |
Slow |
Medium |
Extra Rinse |
low-speed tumbling and |
trousers, pants, |
|
Warm |
Medium |
Med Heavy |
Fresh Hold®/Fresh |
medium-speed spin for |
and dresses |
|
Very Warm |
Med Fast |
Heavy |
Spin™ |
gentle fabric care and |
|
|
Hot |
Fast |
|
Extra power |
reduced wrinkling. |
|
|
|
|
|||
|
|
|
|
|
|
|
Clothing, |
Sanitize |
Hot |
Off |
Light |
Steam** |
This cycle eliminates |
bedding and |
|
|
Slow |
Medium |
Extra Rinse |
99.99% of the most |
towels requiring |
|
|
Medium |
Med Heavy |
Fresh Hold®/Fresh |
common bacteria |
sanitization |
|
|
Med Fast |
Heavy |
Spin™ |
found in clothes, |
|
|
|
Fast |
|
Extra power |
sheets, and towels. |
|
|
|
|
The extra hot wash |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
temperature ensures |
|
|
|
|
|
|
sanitization. Check |
|
|
|
|
|
|
recommended wash |
|
|
|
|
|
|
temperature of your |
|
|
|
|
|
|
items. Bacteria tested |
|
|
|
|
|
|
were K. pneumonia, |
|
|
|
|
|
|
P. aureginosa, and S. |
|
|
|
|
|
|
aureus. |
Bright or darkly |
Colors |
Cold |
Off |
Light |
Extra Rinse |
Cold water with an |
colored cottons, |
|
|
Medium |
Medium |
Fresh Hold®/Fresh |
additional wash action |
linens, casual |
|
|
Med Fast |
Med Heavy |
Spin™ |
gently lifts stains while |
and mixed loads |
|
|
Fast |
Heavy |
Extra power |
caring for fabrics. |
|
|
|
|
|
|
Settings may be |
|
|
|
|
|
|
adjusted as desired, |
|
|
|
|
|
|
but must use only cold |
|
|
|
|
|
|
water settings. |
2–4 lightly |
Overnight |
Cold |
Fast |
Light |
Steam** |
This short wash cycle |
soiled synthetic |
Wash & |
Cool |
|
Medium |
Extra Rinse |
has an extra-high- |
garments, |
Dry |
Warm |
|
Med Heavy |
Fresh Hold®/Fresh |
speed spin followed by |
athletic |
|
Very Warm |
|
Heavy |
Spin™ |
intermittent tumbling |
uniforms, or |
|
Hot |
|
|
Extra power |
and fan activation to |
|
|
|
circulate air through the |
|||
workout wear |
|
|
|
|
|
|
|
|
|
|
|
clothes. |
|
|
|
|
|
|
|
|
Wet load of |
Drain |
N/A |
Off |
N/A |
Extra Rinse |
Use Drain & Spin to |
clothes |
& Spin |
|
Slow |
|
Fresh Hold®/Fresh |
remove excess water |
|
|
|
Medium |
|
Spin™ |
from the load. Spin |
|
|
|
Med Fast |
|
|
speed can be set to a |
|
|
|
Fast |
|
|
lower setting. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*All temperature selections feature a Cold rinse. |
|
|
|
Continued on next page |
||
|
|
|
|
|||
**The Steam option is only available when a Warm, Very Warm, or Hot water temperature is selected. |
|
|||||
***Spin speed varies by model. |
|
|
|
|
|
9
Items to wash |
Cycle: |
Wash |
Spin |
Soil |
Options/ |
Cycle Details: |
using default |
|
Temperature* |
Speed*** |
Level: |
Modifiers: |
|
cycle settings: |
|
|
|
|
|
|
No clothes in |
Clean |
N/A |
N/A |
N/A |
N/A |
Use this cycle every 30 |
washer |
Washer |
|
|
|
|
washes to keep the inside |
|
with |
|
|
|
|
of your washer fresh and |
|
affresh® |
|
|
|
|
clean. This cycle uses a |
|
|
|
|
|
|
higher water level. Use with |
|
|
|
|
|
|
affresh® washer cleaner |
|
|
|
|
|
|
tablet or liquid chlorine |
|
|
|
|
|
|
bleach to thoroughly clean |
|
|
|
|
|
|
the inside of your washer. |
|
|
|
|
|
|
This cycle should not be |
|
|
|
|
|
|
interrupted. See “Washer |
|
|
|
|
|
|
Care.” |
|
|
|
|
|
|
IMPORTANT: Do not place |
|
|
|
|
|
|
garments or other items |
|
|
|
|
|
|
in the washer during the |
|
|
|
|
|
|
Clean Washer with affresh® |
|
|
|
|
|
|
cycle. Use this cycle with |
|
|
|
|
|
|
an empty wash tub. See |
|
|
|
|
|
|
“Washer Care” in “Washer |
|
|
|
|
|
|
Maintenance.” |
|
|
|
|
|
|
|
*All temperature selections feature a Cold rinse.
**The Steam option is only available when a Warm, Very Warm, or Hot water temperature is selected.
***Spin speed varies by model.
Use only High Efficiency detergents. The package will be marked “HE” or “High Efficiency.” Low-water washing creates excessive sudsing with a non-HE detergent. Using non-HE detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component failure and, over time, buildup of mold or mildew. HE detergents should be low-sudsing and quick-dispersing to produce the right amount of suds for the best performance. They should hold soil in suspension so it is not redeposited onto clean clothes. Not all detergents labeled as High Efficiency are identical in formulation and their ability to reduce suds. For example, natural, organic, or homemade HE detergents may generate a high level of suds. If you use one of these and see an “Sd” or “Sud” error code appear in the display, consider using a different HE detergent. Always follow the detergent manufacturer’s instructions to determine the amount of detergent to use. Do not go over the Max line on the dispenser. See “Using the Dispenser Drawer” or “Using the Optimal Dispense Drawer” for more information.
Use only High Efficiency (HE) detergent.
About Detergent Concentration
Today’s liquid HE detergents are concentrated. Most brands of concentrated HE detergent will show the level of concentration on the bottle. If so, simply set the concentration level in the Optimal Dispense menu to match the level shown on the bottle.
However, if the detergent bottle does not give the concentration, it can be easily calculated. Just divide the package size in fluid ounces by the number of loads. Then refer to the chart below to find the concentration.
If you do not get your desired cleaning results, try using a lower concentration number. If you have excess suds, try using a higher concentration number.
Concentration |
Number of ounces ÷ number of loads |
2X |
1.5–2.49 |
3X |
0.9–1.49 |
4X |
0.7–0.89 |
5X |
0.5–0.69 |
6X |
0.3–0.49 |
1.Open the dispenser drawer.
2.Add laundry products as described in steps 4–6 in the “Using Your Washer” section.
3.Slowly close the dispenser drawer. Make sure it is completely closed.
NOTES:
■■A small amount of water may remain in the dispensers from the previous wash cycle. This is normal.
■■See “About Detergent Concentration” for information on detergent concentration.
■■To ensure you have enough detergent in the dispenser,
the display will show the detergent level (Low and open lid).
■■To add single-dose and Oxi-type boosters, see the “Using Your Washer” section.
10
First wash cycle without laundry
Before washing clothes for the first time, add liquid or powdered
HE detergent to the detergent dispenser. Choose the Quick Wash cycle and run it without clothes. Use only HE detergent. This initial cycle serves to ensure the interior is clean and the dispenser drawer is ready for use before washing clothes.
1. Sort and prepare your laundry
Sort items by recommended cycle, water temperature,
and colorfastness. Separate heavily soiled items from lightly soiled. Separate delicate items from sturdy fabrics. Treat stains promptly and check for colorfastness by testing stain remover products on an inside seam.
IMPORTANT:
■■Empty pockets. Loose change, buttons, or any small object can plug pumps and may require a service call.
■■Close zippers, fasten hooks, tie strings and sashes, and remove non-washable trim and ornaments.
■■Mend rips and tears to avoid further damage to items during washing.
■■Turn knits inside out to prevent pilling. Separate lint-takers from lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.
■■Do not dry garments if stains remain after washing because heat can set stains into fabric.
■■Always read and follow fabric care labels and laundry product instructions. Improper usage may cause damage to your garments.
2. Add laundry products (if desired)
Single-dose laundry packets, Oxi-type boosters, color-safe bleach, or fabric softener crystals can be added to the drum prior to adding laundry.
NOTE: Always follow manufacturer’s instructions.
11
3. Load laundry into washer 4. Add HE detergent
Optimal Dispense Drawer
Place a load of sorted items loosely in the washer. Items need to move freely for best cleaning and to reduce wrinkling and tangling. Close the washer door by pushing it firmly until the latch clicks.
■■Depending on load type and cycle, the washer can be fully loaded but not tightly packed. Washer door should close easily. See “Cycle Guide” for loading suggestions.
■■Mix large and small items and avoid washing single items. Load evenly.
■■Wash small items in mesh garment bags. For multiple items, use more than one bag and fill bags equally.
If using the optimal dose dispenser, do not need to add detergent for every load, the dispenser will take automatically.
Single Load Dispenser Drawer
Liquid |
Powdered |
HE detergent |
HE detergent |
Adjust the selector, based on type of HE detergent used (either liquid or powdered). See “Using the Dispenser Drawer” section on how to use the dispenser.
■■Push load fully into washer. Make sure no items are resting on the rubber seal to avoid trapping them between the seal and the door glass.
NOTE: Do not add single-dose laundry packets, Oxi-type boosters, color-safe bleach, or fabric softener crystals to dispensers. They will not dispense correctly.
12
5. Add liquid fabric softener to dispenser (if desired)
Optimal Dispense Drawer
Single Load Dispenser Drawer
6. Add liquid chlorine bleach to dispenser (if desired)
Optimal Dispense Drawer
Single Load Dispenser Drawer
Pour a measured amount of liquid fabric softener into liquid fabric softener compartment. Always follow manufacturer’s directions for correct amount of fabric softener based on your load size.
Fabric softener is always dispensed in the last rinse, even if Extra Rinse is selected.
IMPORTANT: Do not overfill, dilute, or use more than manufacturer's recommendation for dosing of fabric softener. Do not fill past the Max line. Overfilling dispenser will cause fabric softener to immediately dispense into washer.
■■Do not spill or drip any fabric softener onto the clothes.
■■Do not use liquid fabric softener dispenser balls in this washer. They will not dispense correctly.
Add liquid chlorine bleach to the bleach compartment. Do not overfill, dilute, or use more than manufacturer's recommendation for dosing. Do not use color-safe bleach or Oxi in the same cycle with liquid chlorine bleach.
IMPORTANT:
■■Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not guess.
■■Do not fill beyond the Max level. Overfilling could cause garment damage.
■■Do not use thickened, easy-pour, or no-splash bleach when running the Clean Washer with affresh® cycle as excess suds may occur.
13
|
7. Touch POWER to turn on washer |
10. Select any additional options* |
|
|
|
|
|
|
|
|
|
Slowly close the Dispense drawer. Make sure the drawer is closed completely, then touch POWER to turn on the washer or go to Step 8.
8. Select CYCLE*
Turn cycle knob to select your wash cycle. See “Cycle Guide” for details on cycle features. Press the knob for enabling the Extra Power option.
The Extra Power option boosts stain fighting performance on any wash cycle with a dual temperature wash, combining cold and hot temperature during different phases of the wash time. Press the knob to select this option.
9. Adjust settings, if desired*
The display will show the default settings for the selected cycle. To adjust a setting, touch its name – Temp, Spin or Soil. Adjusting settings will change the Estimated Cycle Time. Tightly packing the load, unbalanced loads, or excessive
suds may also cause the washer to increase the cycle time.
To add an option to the cycle, touch its name – Fresh Hold, Steam, Extra Rinse, Cycle Signal, or Control Lock.
To remove an option from the selected cycle, touch the option again.
11. Set detergent concentration
(On Optimal Dispense Model only)
You can adjust the detergent concentration setting if needed. Default settings are 2x detergent concentration. If the detergent concentration is not listed on the package, see “About Detergent Concentration” to calculate the concentration.
To Adjust Dispenser Settings:
Press and hold the Temp & Soil until the display shows the desired concentration level.
The washer will remember this level until it is changed.
*Not all options and settings are available with all cycles. See “Cycle Guide” for available options and settings.
14
|
12. Set a delayed wash |
14. Remove garments promptly |
|
|
|
|
after cycle is finished |
|
|
|
|
|
|
|
|
|
|
|
|
If you do not want to begin a cycle immediately, you may choose the Delay Hrs. option. This will delay the start of the wash cycle by up to 12 hours.
To set a delayed wash:
1.Touch SELECT Delay Start to set the desired delay time.
2.Touch and hold START to start the delay countdown. The countdown stops blinking.
13.Touch and hold START to begin wash cycle
Touch and hold START to start the wash cycle. To pause a cycle in progress, touch START once, then touch and hold again to continue the cycle. To cancel a cycle, touch POWER.
Once you touch and hold START, you will hear the door lock, unlock, and lock again. The washer door will remain locked during the wash cycle.
Unlocking the door to add garments:
If you need to open the door to add 1 or 2 missed garments, you may do so while the “Add Garment” light is lit. The time allowed to add a garment will vary based on cycle selection and load size.
Touch START once; the door will unlock once the washer movement has stopped. This may take several minutes. Then close the door and
touch and hold START again to restart the cycle.
Adding items after “Add Garment” light is off:
Cancel current cycle. Water will drain and you will need to reselect cycle and restart.
For wash performance and optimal energy savings, add garments only when the “Add Garment” light is on.
Promptly remove garments after cycle has completed to avoid odor and rusting of
metal objects on garments. When unloading garments, pull back the door seal and check for small items between the tub and the washer drum.
If you will be unable to remove the load promptly, use the Fresh Hold®/Fresh
Spin™ option. If the Fresh Hold®/Fresh Spin™ option is selected, the washer will automatically activate the fan and tumble
the load periodically for up to 24 hours. To turn off the Fresh Hold®/Fresh Spin™ option, touch POWER. To set the washer so that the
Fresh Hold®/Fresh Spin™ option does not come on for future cycles, touch FRESH HOLD.
NOTES:
■■The door will remain locked while the Fresh Hold®/Fresh Spin™ option is active. To cancel the option and unlock the door, touch POWER.
■■A small amount of water may remain in the dispensers after the wash cycle is complete. This is normal.
■■This washer has a tight seal to avoid water leaks. To avoid odors, leave the door open to allow the washer to dry between uses.
15
WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses:
■■Mark the date of replacement on the label with a permanent marker.
■■Check that the old washers are not stuck on the washer inlet valves.
■■Use new washers in the new inlet hoses to ensure a proper seal.
WASHER CARE
Recommendations to Help Keep Your Washer Clean and Performing at Its Best
1.Always use High Efficiency (HE) detergents and follow the HE detergent manufacturer’s instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside your washer which, in turn, may result in undesirable odor.
2.Use warm or hot water washes sometimes (not exclusively cold water washes) because they do a better job of controlling the rate at which soils and detergent accumulate.
3.Always leave the washer door slightly ajar between uses to help dry out the washer and avoid the buildup of odor-causing residue.
4.Periodically clean residue from all interior surfaces of the glass window. For better care, wipe the entire inside of the glass door with a damp cloth.
Cleaning Your Front-Loading Washer
Read these instructions completely before beginning the routine cleaning processes recommended below.
This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.
Cleaning the Door Seal
1.Open the washer door and remove any clothing or items from the washer.
2.Inspect the gray-colored seal between the door opening and the drum for stained areas or soil buildup. Pull back the seal to inspect all areas under the seal and to check for foreign objects.
WASHER CARE (cont.)
3.If stained areas or soil buildup is found, wipe down these areas of the seal using either of the following two procedures:
a.affresh® Machine Cleaning Wipes Procedure:
i.When the cycle is complete, gently pull back the rubber door seal and clean the entire surface with the textured side of an affresh® Machine Cleaning Wipe.
b.Dilute Liquid Chlorine Bleach Procedure:
i.Mix a dilute bleach solution, using ¾ cup (177 mL) of liquid chlorine bleach and 1 gallon (3.8 L) of warm tap water.
ii.Wipe the seal area with the dilute solution, using a damp cloth.
iii.Let stand 5 minutes.
iv.Wipe down area thoroughly with a dry cloth and let washer interior air dry with door open.
IMPORTANT:
■■Wear rubber gloves when cleaning with bleach.
■■Refer to the bleach manufacturer’s instructions for proper use.
Cleaning the Inside of the Washer
This washer has a special cycle that uses higher water volumes in combination with affresh® Washer Cleaner or regular liquid chlorine bleach to thoroughly clean the inside of the washer. Steam washer models also utilize steam to enhance cleaning in this special cycle.
IMPORTANT: Do not use thickened, easy-pour, or no-splash bleach when running the Clean Washer with affresh® cycle as excess suds may occur.
NOTE: Read these instructions completely before beginning the cleaning process.
Begin Procedure
1.Clean Washer with affresh® Cycle Procedure (Recommended for Best Performance):
a.Open the washer door and remove any clothing or items.
b.Use an affresh® Machine Cleaning Wipe or a soft, damp cloth or sponge to clean the inside door glass.
c.Add an affresh® Washer Cleaner tablet to the washer drum.
d.Do not add the affresh® Washer Cleaner tablet to the dispenser drawer.
e.Do not add any detergent or other chemical to the washer when following this procedure.
f.Close the washer door.
g.Select the Clean Washer with affresh® cycle.
h.On some models: Select the Fresh Hold®/Fresh Spin™ option to help dry the washer interior after the cycle is complete.
NOTE: The washer remembers your last option selection and will use it for future wash cycles until you deselect that option. While the fan is ON, the washer door will lock. To unlock the door, touch POWER.
i.Touch and hold START to begin the cycle. The Clean Washer with affresh® Cycle Operation is described below.
16
WASHER CARE (cont.)
2.Chlorine Bleach Procedure:
a.Open the washer door and remove any clothing or items.
b.Open the dispenser drawer and add regular liquid chlorine bleach to the MAX level in both the bleach compartment and the fabric softener compartment. Either traditional or HE chlorine bleach can be used.
IMPORTANT: Do not use thickened, easy-pour, or no-splash bleach as excess suds may occur.
NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over time.
c.Close the washer door and the dispenser drawer.
d.Do not add any detergent or other chemicals to the washer when following this procedure.
e.Close the washer door.
f.Select the Clean Washer with affresh® cycle.
g.On some models: Select the Fresh Hold®/Fresh Spin™ option to help dry the washer interior after the cycle is complete.
NOTE: The washer remembers your last option selection and will use it for future wash cycles until you deselect that option. While the fan is ON, the washer door will lock. To unlock the door, touch POWER.
h.Touch and hold START to begin the cycle. The Clean Washer with affresh® Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle.
Description of Clean Washer with affresh® Cycle Operation:
1.The Clean Washer with affresh® cycle will determine whether clothing or other items are in the washer.
2.If no items are detected in the washer, it will proceed with the cycle.
a.If any items are detected in the washer, “rL” (remove load) will be displayed. The door will unlock. Open washer and remove any garments from the washer drum.
b.Touch POWER to clear the “rL” code.
c.Touch and hold START to restart the cycle.
3.Steam models only: During the first 20 minutes of the cycle, it will activate the steamer but the drum will not spin or fill with water. You may see condensation on the door glass during this initial phase. If you are using an affresh® Washer Cleaner tablet, it will not dissolve completely during the steam phase. This is normal.
After the cycle is complete, leave the door open slightly to allow for better ventilation and drying of the washer interior.
Cleaning the Dispensers
After a period of using your washer, you may find some residue buildup in the washer’s dispensers. To remove residue from the dispensers, remove the drawer and wipe the surfaces with an affresh® Machine Cleaning Wipe or a damp cloth and towel dry either before or after you run the Clean Washer with affresh® cycle. Use an all-purpose surface cleaner, if needed.
IMPORTANT: Dispenser is not dishwasher safe.
Cleaning the Outside of the Washer
Use an affresh® Machine Cleaning Wipe or a soft, damp cloth or sponge to wipe up any spills. Occasionally wipe the outside of your washer to help keep it looking new. Use an affresh® Machine Cleaning Wipe or mild soap and water.
IMPORTANT: To avoid damaging the washer’s finish, do not use abrasive products.
CLEAN WASHER CYCLE REMINDER
NOTE: Not all models have the Clean Washer with affresh® cycle reminder light.
The Clean Washer with affresh® LED will flash at the end of a wash cycle
when the washer has run 30 wash cycles. This is a reminder to run the Clean Washer with affresh® cycle.
If the Clean Washer with affresh® cycle is not turned on, the LED will stop flashing at the end of a wash cycle after running 3 more regular wash cycles. After 30 more wash cycles are completed, the Clean Washer with affresh® LED will again flash at the end of a wash cycle as a reminder.
REMOVING THE DISPENSER
Optimal Dispense Drawer
To remove:
1.Pull dispenser drawer out until it stops.
2.Press down on the release tab and pull straight out to remove the dispenser.
3.Lift off cover panel by pulling straight up.
To replace:
1. Slide cover panel back onto posts on dispenser.
2. Align edges of dispenser with guides in washer, then slide dispenser back into slot.
17
REMOVING THE DISPENSER (cont.)
Single Load Dispenser Drawer
Removing the Dispenser
To remove:
1.Pull dispenser drawer out until it stops.
2.Press down on the release tab and pull straight out to remove the dispenser.
3.Lift off cover panel by pulling straight up.
To replace:
1.Slide cover panel back onto posts on dispenser.
2.Align edges of dispenser
with guides in washer, then slide dispenser back into slot.
NON-USE AND VACATION CARE
Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:
1.Unplug or disconnect power to washer.
2.Turn off water supply to washer to avoid flooding due to water pressure surges.
HELPFUL TIP: Attach a reminder note to the washer to turn the water back on before washer’s next use.
3.Clean the dispensers. See “Cleaning the Dispensers.”
18
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.
To winterize washer:
1.Shut off both water faucets, then disconnect and drain water inlet hoses.
HELPFUL TIP: Attach a reminder note to the washer to turn the water back on before washer’s next use.
2.Put 1 qt (1 L) of R.V.-type antifreeze in washer drum and run washer on Normal cycle for about 2 minutes to mix antifreeze and remaining water.
3.Unplug washer or disconnect power.
TRANSPORTING YOUR WASHER
1.Shut off both water faucets. Disconnect and drain water inlet hoses.
2.If washer will be moved during freezing weather, follow “Winter Storage Care” directions before moving.
3.Disconnect drain hose from drain system and from back of washer.
4.Unplug power cord.
5.Place inlet hoses and drain hose inside washer drum.
6.Bundle power cord with a rubber band or cable tie to keep it from hanging onto the ground.
IMPORTANT: Call for service to install new transport bolts. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid structural damage to
your washer, it must be properly set up for relocation by a certified technician.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage, or moving:
1.Refer to Installation Instructions to locate, level, and connect washer.
2.Before using again, run washer through the following recommended procedure:
To use washer again:
1.Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.
2.Plug in washer or reconnect power.
3.Run washer through Power Wash cycle to clean washer and remove antifreeze, if used. Use only HE detergent. Use half the manufacturer’s recommended amount for a medium-size load.
19
First try the solutions suggested here or visit our website at www.maytag.com/product_help –
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience |
Possible Causes |
Solution |
|
|
|
Error Code Appears in Display (for 2- and 3-digit displays)
Once any possible issues are corrected, touch POWER once to clear the code. Reselect and restart the cycle.
“Sd” or “Sud” |
Excessive suds in washer. Washer is |
Allow the washer to continue. Use only HE detergent. Always |
|
(excess suds) appears |
running a suds-reduction routine. |
follow the detergent manufacturer’s instructions to determine |
|
in display |
|
the amount of detergent to use and base detergent quantity |
|
|
|
on load size. Not all detergents labeled as High Efficiency are |
|
|
|
identical in formulation and their ability to reduce suds. For |
|
|
|
example, natural, organic, or homemade HE detergents may |
|
|
|
generate a high level of suds. If you use one of these and see |
|
|
|
an “Sd” or “Sud” error code appear in the display, consider |
|
|
|
using a different HE detergent. |
|
|
|
|
|
Lo followed by FL or F8 |
Check for proper water supply. |
Unit will drain for 8 minutes while door remains locked. The |
|
followed by E1 |
|
drain cycle must be allowed to complete or the error code |
|
or |
|
cannot reset. When complete, touch POWER once to clear the |
|
Lo followed by FL or |
|
code. Then touch POWER again to restart washer. |
|
F08 followed by E01 |
|
If code appears again, call for service. |
|
(water supply error) |
|
|
|
|
Both hoses must be attached and have water flowing to the |
||
appears in display |
|
||
|
inlet valve. |
||
|
|
||
|
|
|
|
|
|
Both hot and cold water faucets must be ON. |
|
|
|
|
|
|
|
Inlet valve screens on washer may be clogged. |
|
|
|
|
|
|
|
Remove any kinks in the inlet hose. |
|
|
|
|
|
|
|
If used, auto shut-off connectors and hoses must be properly |
|
|
|
installed and in working order. |
|
|
Check for proper inlet hoses. |
Use only manufacturer’s recommended inlet hoses. |
|
|
|
|
|
F9 followed by E1 |
Check plumbing for correct drain |
Check drain hose for proper installation. |
|
or |
hose installation. Drain hose extends |
|
|
Make sure the drain hose is not kinked, pinched, or blocked. |
|||
F09 followed by E01 |
into standpipe farther than 41⁄2" |
||
(drain pump system |
(114 mm). |
Remove any clogs from drain hose. |
|
error) appears in display |
|
|
|
|
Use drain hose form and securely attach to drainpipe or tub. |
||
|
|
||
|
|
|
|
|
|
Lower drain hose if the end is higher than 96" (2.4 m) above |
|
|
|
the floor. |
|
|
|
|
|
|
Not using HE detergent or using too |
Use only HE detergent. Always measure detergent and follow |
|
|
much HE detergent. |
manufacturer’s directions based on load size and soil level. |
|
|
|
|
|
F5 followed by E2 |
Washer door not locking. |
Touch POWER to cancel the cycle. Check that the door is |
|
or |
|
closed completely and latching. Check for items in the washer |
|
F05 followed by E02 |
|
drum that may be keeping the door from closing completely. |
|
(door will not lock) |
|
|
|
appears in display |
|
|
|
|
|
|
|
“rL” (remove load) |
Load detected in drum during Clean |
Remove items from washer drum and restart Clean Washer |
|
appears in display |
Washer with affresh® cycle. |
with affresh® cycle. |
20