Maytag MGR7661WB0, MGR7662WB0, MGR7662WW0, MGR7661WW0, MGR7662WB2 Installation Instructions Manual

...

0 (0)

INSTALLATIONINSTRUCTIONS

30" (76.2 CM) FREESTANDINGGAS RANGES

INSTRUCTIONSD'INSTALLATIONDESCUISINIERESA GAZ

AUTOPORTANTESDE30" (76,2 CM)

TableofContents/Tabledes mah_res

RANGE SAFETY ............................................................................. 2

INSTALLATION REQUIREMENTS ............................................... 3

Tools and Parts............................................................................ 3

Location Requirements ............................................................... 3

Electrical Requirements ............................................................... 5

Gas Supply Requirements ........................................................... 5

INSTALLATION INSTRUCTIONS ................................................. 6

Unpack Range ............................................................................. 6

Install Anti-Tip Bracket ................................................................ 7

Make Gas Connection ................................................................. 8

Verify Anti-Tip Bracket Location .................................................. 9

Level Range ................................................................................. 9

Electronic Ignition System ........................................................... 9

Replace Oven Racks and Storage or Warming Drawer ........... 11

Complete Installation ................................................................. 11

GAS CONVERSIONS ................................................................... 12

LP Gas Conversion .................................................................... 12

Natural Gas Conversion ............................................................ 14

ANTI-TIP BRACKET TEMPLATE ................................................ 32

SI_CURITI_ DE LA CUISINII_RE ................................................... 16

EXIGENCES D'INSTALLATION ................................................... 17

Outillage et pieces ...................................................................... 17

Emplacement d'installation ........................................................ 17

Specifications electriques .......................................................... 19

Specifications de I'alimentation en gaz ..................................... 19

INSTRUCTIONS D'INSTALLATION ............................................ 21

Deballage de la cuisiniere .......................................................... 21

Installation de la bride antibasculement .................................... 21

Raccordement a la canalisation de gaz ..................................... 22

Verification de I'emplacement de la bride antibasculement .....23

Mise &niveau de la cuisiniere .................................................... 24

Systeme d'allumage electronique ............................................. 24

Reinstallation des grilles du four et du tiroir de

remisage ou du tiroir-rechaud ................................................... 26

Achever I'installation .................................................................. 26

CONVERSIONS POUR CHANGEMENT DE GAZ ...................... 26

Conversion de Gaz naturel & Propane ....................................... 26

Conversion de Propane & Gaz naturel ....................................... 29

GABARIT POUR LA BRIDE ANTIBASCULEMENT .................... 32

iMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

Installateur : Remettre les instructions d'installation au propri6taire.

Propri6taire : Conserver les instructions d'installation pour r6f6rence ult_rieure.

W10196160C

RANGESAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death,

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance,

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier,

Tip Over Hazard

A child or adult can tip the range and be killed. Connect anti=tip bracket to rear range foot.

Reconnect the anti=tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATIONREQUIREMENTS

s c nd

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed

• Tape measure • Marker or pencil

• Flat-blade screwdriver • Pipe-joint compound

• Phillips screwdriver

• Level • 3/le"(4.8 mm) carbide-tipped

• Hand or electric drill concrete/ceramic floors)

• Hammer • Noncorrosive leak-detection

• Wrench or pliers

• Pipe wrench For LP/Natural Gas

• 18/le"combination wrench • 1/2"combination wrench

• 1¼,,drive ratchet • 8/8"combination wrench

• 3/8"nut driver • 8/le"nut driver

• 1/8"(3.2 mm) drill bit (for • Quadrex ®tor Phillips wood floors) screwdriver

Parts supplied

Check that all parts areincluded.

A.Anti-tip bracket B. Plastic anchors (2) C. #10 x 1/=.screws (2)

Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your

local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See "Electrical Requirements" and "Gas Supply Requirements" sections.

resistant to LP gas

masonry drill bit (for

solution

Conversions

• Masking tape

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

• It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the oven frame behind the storage drawer panel.

The range should be located for convenient use in the kitchen.

Recessed installations must provide complete enclosure of the sides and rear of the range.

All openings in the wall or floor where range is to be installed must be sealed.

Do not seal the range to the side cabinets. Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances. The floor anti-tip bracket must be installed. To install the anti-

tip bracket shipped with the range, see "Install Anti-Tip Bracket" section.

• Grounded electrical supply is required. See "Electrical Requirements" section.

• Proper gas supply connection must be available. See "Gas Supply Requirements" section.

• Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C).

• Use an insulated pad or 1A" (0.64 cm) plywood under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or with local codes. In Canada, the installation of this range must conform with the

current standards CAN/CSA-A240-1atest edition, or with local codes.

Mobile home installations require:

• When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as itconforms to the standards

listed above.

1-@QUADREX is a registered trademark of NLW Holdings, Inc.

Product Dimensions

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or

microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

B C

A. 2T%_" (69.9 cm) max. depth with handle B. 36" (91.4 cm) cooktop height (max.) with leveling

legs screwed all the way in*

C. 467/8" (119.1 cm) overall height (max.) with

levering legs screwed all the way in*

D. 29%" (75.9 cm) width

E. 25" (63.5 cm)

*Range can be raised approximately 1" (2.5 cm) by adjusting the

leveling legs.

A. 18" (45.7 cm) upper side cabinet to countertop B. 13" (33 cm) max. upper cabinet depth C. 30" (76.2 cm) min. opening width D. For minimum clearance to top of cooktop, see NOTE*. E. 30%" (76.5 cm) min. opening width

F. This shaded area recommended for installation of rigid gas

pipe.

G. 8" (20.3 cm)

H. Grounded outlet

I. 17" (43.2 cm)

2.2" (5.1 cm)

K. 41/_'' (11.4 cm)

L. 2" (5.1 cm) min. clearance from both sides of range to side

wall or other combustible material.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal

cabinet is covered by not less than 1/4"(0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper. 30" (76.2 cm) minimum clearance between the top of the

cooking platform and the bottom of an uncovered wood or metal cabinet.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

IMPORTANT: The range must be electrically grounded in

accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

This range is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that

the ground path is adequate. A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.

• Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.

• The wiring diagram is located on the underside of the storage drawer or below the warming drawer in a clear plastic bag.

NOTE: The metal chassis of the range must be grounded in order for the control panel to work. If the metal chassis of the range is not grounded, no keypads will operate. Check with a qualified electrician if you are in doubt as to whether the metal chassis of the range is grounded.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut=off valve. Securely tighten all gas connections.

if connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel, authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest

edition. IMPORTANT: Leak testing of the range must be conducted

according to the manufacturer's instructions.

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

• This range is factory set for use with Natural gas. See "Gas Conversions" section. The model/serial rating plate located behind the storage drawer on the right-hand side oven door frame has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP gas conversion: Conversion must be done by a qualified service technician. No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See "Gas

Conversions" section.

Gas Supply Line

• Provide a gas supply line of 3_,,(1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be _/_"(1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON ®ttape.

Flexible metal appliance connector:

If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, 1/2"(1.3 cm) or 3_,,(1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line.

• A 1/2"(1.3 cm) male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance

pressure regulator.

• Do not kink or damage the flexible metal tubing when moving the range.

Rigid pipe connection: The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the range. The rigid pipe must be level with the range connection. All strains must

be removed from the supply and fuel lines so range will be level and in line.

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for proper operation:

Natural gas: Minimum pressure: 5" WCP Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP Maximum pressure: 14" WCP Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Must include a shutoff valve: The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but external to the range opening, such as an adjacent cabinet. It

should be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the range.

A. Gas supply line B. Shutoff valve "open" position C. To range

t®TEFLON isa registeredtrademark of E.I.Du Pont De NemoursandCompany.

INSTALLATIONINSTRUCTIONS

Unpc c <FScsnc, e

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least 1" water column pressure above the manifold pressure shown on

the model/serial rating plate.

Line pressure testing above 1/2psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2psi (3.5 kPa).

Line pressure testing at 1/2psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2psi (3.5 kPa).

3. Do not remove the shipping base at this time.

Use two or more people to move and install range. Failure to do so can result in back or other injury.

Excessive Weight Hazard _

1. Remove shipping materials, tape and film from range.

2. Remove oven racks and parts package from inside oven.

A .................................

A. Shipping base

On Ranges Equipped with Storage Drawers:

Remove the storage drawer. Use a ¼" drive ratchet to lower the rear leveling legs one-half turn. Use a wrench or pliers to lower front leveling legs one-half turn.

If countertop is not flush with cabinet opening edge, align template with overhang.

A. ¼" drive ratchet B. Rear leveling leg

C. Wrench or priers D. Front levering leg

On Ranges Equipped with Warming Drawers:

Use wrench or pliers to lower the front and rear leveling legs one-half turn.

A B

A. Rear levering leg B. Front leveling leg C. Wrench or priers

If cabinet opening is wider than that specified inthe "Location Requirements" section, adjust template so range will be

centered in cabinet opening.

To mount anti-tip bracket to wood floor, drill two 1/8"(3.2 mm) holes at the positions marked on the bracket template.

Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a 3/le"(4.8 mm) masonry drill bit to drill 2 holes at the positions

marked on the bracket template. Remove template from floor. Tap plastic anchors into holes with a hammer.

Align anti-tip bracket holes with holes in floor. Fasten anti-tip bracket with screws provided.

Tip Over Hazard

A child or adult can tip the range and be killed. Connect anti=tip bracket to rear range foot.

Reconnect the anti=tip bracket, if the range is moved. Failure to follow these instructions can result in death

or serious burns to children and adults.

Contact a qualified floor covering installer for the best procedure for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard or hardboard.

1. Remove template from the anti-tip bracket kit (found inside the oven cavity) or from the back of this manual.

2. Place template on the floor in cabinet opening so that the left edge is against cabinet and top edge is against rear wall, molding or cabinet.

3. Tape template into place.

Depending on the thickness of your flooring, longer screws may be necessary to anchor the bracket to the subfloor. Longer screws are available from your local hardware store.

Move range close enough to opening to allow for final electrical connection. Remove shipping base, cardboard or hardboard from under range.

Move range into its final location making sure rear leveling leg slides into anti-tip bracket.

9. If installing the range in a mobile home, you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the "Location Requirements" section.

10. Continue installing your range using the following installation instructions.

3. Use a lS/le"combination wrench and channel lock pliers to attach the flexible connector to the adapters. Check that

connector is not kinked.

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut=off valve. Securely tighten all gas connections.

if connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range to the existing gas line. Your connections may be different, according to the supply line type, size and location.

1. Apply pipe-joint compound made for use with LP gas to all pipe thread connections.

2. Using a pipe wrench to tighten, connect the gas supply to the range.

A B C

H G F

A. Gas pressure regulator

B. Use pipe-joint compound.

C. Adapter (must have Y2"male

pipe thread)

D. Flexible connector

E.Manual gas shutoff valve F Y2"or 3/4"gas pipe

G. Use pipe-joint compound. H. Adapter

Complete Connection

1. Check that the gas pressure regulator shutoff valve is in the "on" position.

A. Gas pressure regulator shutoff valve

2. Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe.

A F

A. Gas pressure regulator B. 90 ° elbow (must have

Y2"male pipe thread)

C. Nipple D. Union

E. Black iron pipe

{_ ,,,-_D

F Manual gas shutoff valve

G. Y2"or 3/4"gas pipe

H. Nipple

I. Union

J. 90° elbow

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the smaller thread ends of the flexible connector adapters (see B and G in following illustration).

2. Attach one adapter to the gas pressure regulator and the other adapter to the gas shutoff valve. Tighten both adapters.

A. Closed valve B. Open valve

Test all connections by brushing on an approved noncorrosive leak-detection solution. If bubbles appear, a leak is indicated. Correct any leak found.

Remove cooktop burner caps and grates from parts package. Burner caps should be level when properly positioned. If burner caps are not properly positioned, surface burners will not light. Place burner grates over burners and caps.

A..........

A. Burner base B. Burner cap

C. Burner grate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

5. Plug into a grounded 3 prong outlet.

On models with a storage drawer, pull drawer open to first stop position. Lift front of drawer to clear white wheels in drawer guides. Remove drawer and set it aside on a covered

surface. On models with a warming drawer, the rear leg cannot be

seen by removing the warming drawer. It will be necessary to view the rear foot from outside the range.

To check that the anti-tip bracket is installed, use a flashlight and look underneath the bottom of the range.

• Look for the anti-tip bracket securely attached to floor.

• Slide range back so rear range foot is under anti-tip

bracket.

If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket.

On Ranges Equipped with Storage Drawers: Use a1¼,,drive ratchet, wrench or pliers to adjust leveling legs

up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip

bracket.

On Ranges Equipped with Warming Drawers:

Use a wrench or pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

Initial lighting and gas flame adjustments

Cooktop and oven burners use electronic igniters in place of standing pilots. When the cooktop control knob is turned to the "LITE" position, the system creates a spark to light the burner.

This sparking continues, as long as the control knob is turned to

"LITE." When the oven control is turned to the desired setting, sparking

occurs and ignites the gas.

Check Operation of Cool(top Burners

Standard Surface Burners

Push in and turn each control knob to the "LITE" position.

The flame should light within 4 seconds. The first time a burner is

lit it may take longer than 4 seconds to light because of air in the gas line.

If burners do not light properly:

• Turn cooktop control knob to the "OFF" position.

• Check that the range is plugged in. Check that the circuit breaker has not tripped or the household fuse has not blown.

• Check that the gas shutoff valves are set to the "open" position.

• Check that burner caps are properly positioned on burner bases.

Repeat start-up. If a burner does not light at this point, turn the control knobs to "Off" and contact your dealer or authorized service company for assistance.

Place a rack in oven.

Place level on rack and check levelness of range, first side to side; then front to back.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop "low" burner

flame should be a steady blue flame approximately 1¼.(0.64 cm) high.

A _ ___5q3-

Lrd Lrd Lr'd Lrd Lr'd Lrd

A. Low flame

B. High flame

To adjust standard burner: The flame can be adjusted using the adjustment screw inthe

center of the valve stem. The valve stem is located directly underneath the control knob.

If the "low" flame needs to be adjusted:

A. Control knob stem B. Screwdriver

1. Light 1 burner and turn to lowest setting.

2. Remove the control knob. Hold the knob stem with a pair of pliers. Use a small flat-

blade screwdriver to turn the screw located in the center of the control knob stem until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI," checking the flame at each setting.

5. Repeat above steps for each burner.

Using a mirror: Insert a mirror to one side of the burner. Look into the mirror

to check flame.

A.Mirror B.Flame spreader

C.Flame reflection D.2 screws

4. Push the BAKE pad.

5. Press the START pad.

The oven bake burner should light within 8 seconds. Under

certain conditions it may take the burner up to 50 to 60 seconds to light.

Electronic igniters are used to light the bake and broil burners. Refer to the Use and Care Guide for proper operation of the oven

controls.

Check Operation of Oven Bake Burner

1. Remove the oven rack.

2. To remove the oven bottom: Remove 2 screws at the rear of the oven bottom. Lift the rear of the oven bottom up and back

until the front of the panel is away from the front frame. Remove from oven and place on a covered surface.

A. Screws

You can check the burner flame by removing the flame spreader or by using a mirror.

Remove flame spreader: Remove 2 screws from the front tabs of the flame spreader. Lift front of the flame spreader and pull forward to remove

tabs from rear of oven.

Adjust Oven Bake Burner Flame (if needed)

1. On models with a warming drawer, remove access cover plate (1 screw) located at the back of the warming drawer compartment.

2. Check the oven bake burner for proper flame. This flame should have a 1/2"(1.3 cm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should be clean and soft in character. No yellow tips, blowing or lifting of flame should occur.

3. If the oven bake flame needs to be adjusted, locate the air shutter near the center rear of the range. Loosen the locking

screw and rotate the air shutter until the proper flame appears. Tighten locking screw.

A.Air shutter B.Locking screw

Push CANCEL/OFF when finished.

Reinstall flame spreader and oven bake burner cover.

+ 22 hidden pages