Maytag MHW7000XG2, MHW9000YR0, MHW7000XR2, MHW7000XW2, MHW6000XG2 Installation Instructions Manual

...

0 (0)

WASHER INSTALLATION

INSTRUCTIONS

D'INSTALLATION

DE LA LAVEUSE

Table of Contents

WASHER SAFETY ......................................................... 1

iNSTALLATiON REQUIREMENTS ................................ 2

Tools and Parts ................................................................ 2

Location Requirements .................................................. 2

Drain System ................................................................... 4

Electrical Requirements ................................................. 5

iNSTALLATiON iNSTRUCTiONS .................................. 5

Connect Drain Hose ........................................................ 6

Connect Inlet Hoses ........................................................ 7

Level Washer ................................................................... 8

Complete Installation Checklist ..................................... 9

S¢:CURIT¢: DE LA LAVEUSE ...................................... 10

EXIGENCES D'INSTALLATION .................................. 10

Outillage et pi_ces ........................................................ 10

Exigences d'emplacement ........................................... 11

Syst_me de vidange ...................................................... 13

Specifications _lectrique .............................................. 13

iNSTRUCTiONS D'INSTALLATION ............................ 14

Raccordement du tuyau de vidange ............................ 15

Raccordement des tuyau× d'arriv_e d'eau ................. 16

(--tablissment de I'aplomb de la laveuse ...................... 17

Liste de v6rification pour I'ach_vement

de I'installation .............................................................. 19

Table des matibres

iNSTALLATiON NOTES NOTES SUR L'INSTALLATION

Date of purchase: Date of installation:

Installer: Model number:

Serial number:

Date d'achat : Date d'installation : Installateur :

Num_ro de module : Num_ro de s_rie :

WASHER S_ETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10254447A W10254448A-SP

INSTALLATION REQU[REMENW$

Tools and Parts Gather required tools and parts before starting installation.

Tools needed:

l® ® ®J

Adjustable or open end wrenches 1//, (13 mm) and %6" (14 mm)

4 =.rain

(102 mrn}_

Wood block

Pliers that open to 1%_" (39.5 mm)

Parts supplied: NOTE: All parts supplied for installation are in the washer

basket.

Level

Ruler or measuring tape

Optional tools:

C 3

Flashlight

Available Accessories: An optional matching pedestal is available for your washer.

Please contact your retailer for ordering information, or see the Assistance or Service page on the back of your Use and

Care Guide.

Alternate parts: (Not supplied with washer) Your installation may require additional parts. To order, please refer to toll-free numbers on the back page of your Use and

Care Guide.

If you have: Overhead sewer

1" (25 mm) standpipe

Drain hose too short Extension Drain Hose Part

Lint clogged drain

Floor drain system Siphon Break Kit Part Number 285834

Bucket

You will need:

Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump

pump and connectors (available from local plumbing suppliers)

2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter

Part Number 3363920 Connector Kit Part Number 285835

Number 285863 Connector Kit Part Number 285835

Drain Protector Part Number 367031 Connector Kit Part Number 285835

Connector Kit (x2) Part Number 285835 Extension Drain Hose Part

Number 285863

Beaded tie strap Net hoses (2) with

Drain hose with clamp and form (may be shipped

unassembled)

washers

Transport bolt hole

plugs (4)

Alternative inlet Hoses:

(may be required with washer)

[] 8212656RP [] 8212641RP [] 8212546RP [] 8212545RP

[] 8212487RP [] 8212638RP

[] 8212637RP

for some installations, not supplied

10 ft. (3.0 m) Net hose, Black EPDM (2 pack) 5 ft. (1.5 m) Net hose, Black EPDM (2 pack) 4 ft. (1.2 m) Net hose, Black EPDM (2 pack) 5 ft. (1.5 m) Net hose, Red and Blue EPDM

(2 pack) 5 ft. (1.5 m) Nylon braided inlet hose (2 pack) 6 ft. (1.8 m) Nylon braided inlet hose, space

saving 90° elbow, hypro-blue steel couplings (2 pack)

6 ft. (1.8 m) Net hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack)

LOCATION REQUIREMENTS

Proper installation is your responsibility.

You will need:

[] A water heater set to 120 ° F (49° C). [] A grounded electrical outlet located within 6 ft (1.8 m) of

power cord on back of washer.

[] Hot and cold water faucets located within 4 ft (1.2 m) of hot

and cold water fill valves on washer, and water pressure of 20-100 psi (137.9-689.6 kPa).

[] A level floor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet or surfaces with foam backing is not recommended.

[] Floor must support washer's total weight (with water and load)

of 315 Ibs (143 kgs).

iMPORTANT: Do not install, store or operate washer where it will be exposed to weather or in temperatures below 32° F (0° C). Water remaining in washer after use may cause damage in low temperatures. See "Washer Care" in Washer Use and Care Guide for winterizing information.

All dimensions show recommended spacing allowed, except for closet door ventilation openings which are the minimum required.

For each arrangement, consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings.

Space must be large enough to allow door to fully open. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or Iouvered door is installed, top and bottom air openings in door are required.

Recessed area or closet installation (stacked washer and dryer):

27 n

(686 ram)

38"

(965 ram)

(800 ram)

Recessed area or closet installation (washer only):

(TSmm)

48 in.2

(310 cm 2}

1" ft. (25ram)

(25ram)

Custom under counter installation:

O o

1"I")

(76

3 mm

(76 ram}

4" ,!

":,',,,

1" (25 ram)

(25 ram)

Custom cabinet installation:

(178 ram)

ml i '

(102mm) "

/ 1 ml

(25ram)

(76 ram)

)

(25ram)

24 in.2

(155cm2)

i 1 ml

D IN SYSTEN

Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.

IMPORTANT." To avoid siphoning, only 4.5" (113 mm) of drain hose should be inside standpipe. Always secure drain hose with beaded tie strap.

Floor standpipe drain system

Laundry tub drain system

41_2 nn

[113_rnm)

Minimum capacity: 20 gal. (76 L).Top of laundry tub must be at least 30" (762 mm) above floor; install no higher than 96" (2.44 m) from bottom of washer.

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. A 1/4"(6 mm) diameter to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Top of standpipe must be at least 30" (762 mm) high; install no higher than 96" (2.44 m) from bot- tom of washer. If you have an overhead sewer and need to pump higher than 96 inches, a sump pump and associated hardware are

needed. See "Alternative Parts".

Wall standpipe drain system

See requirements for floor standpipe drain system.

Floor drain system

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. See "Alternative Parts". Minimum siphon break height: 28" (710 mm) from bottom of washer. (Additional hoses may be needed.)

ELECTRICAL REQUIREMENTS

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install washer. Failure to do so can result in back or other injury.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

[] A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit

breaker serving only this appliance be provided.

[] This washer is equipped with a power supply cord having

a 3 prong grounding plug.

[] To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation

of the customer to have the properly grounded outlet installed by a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate. [] Do not ground to a gas pipe. [] Check with a qualified electrician if you are not sure the

washer is properly grounded.

[] Do not have a fuse in the neutral or ground circuit.

NOTE: To avoid floor damage, set washer onto cardboard before moving it.

It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.

Move washer to within 4 ft (1.2 m) of its final location. It must be in a fully upright position.

GROUNDING iNSTRUCTiONS

For a grounded, cord=connected washer:

This washer must be grounded. _nthe event of a malfunction or breakdown, grounding wilt reduce the risk of etectricN shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with alt local

codes and ordinances.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman ifyou are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it wilt

not fit the outlet, have a proper outlet installed by a qualified electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on

the appliance.

Locate four transport bolts on rear of washer.

washer

(6. Place power cord over top

Loosen bolts with a 13 mm (1/2") wrench. Slide each bolt and spacer to center of hole. Pull bolts and plastic spacers from back of washer. Discard bolts and spacers.

t4. Cover bolt holes with transport

bolt hole plugs

Close bolt holes on cabinet back with four transport bolt hole plugs included with washer parts.

Remove the yellow shipping strap from the cord. Gently place power cord over top of washer to allow free access

to back of washer.

CONNECW DR_N HOSE

7, Attach drain hose to drain port

If clamp is not already in place on elbow end of drain hose, slide it over end of hose, centering it between the ribs, as

shown. Squeeze clamp with pliers and slide elbow end of drain hose onto drain port and secure with clamp.

For a laundry tub or standpipe drain, go to step 9. For a floor drain, remove the preinstalled drain hose form

as shown in Step 8. You may need additional parts with separate directions. See "Alternative Parts".

Pull power cord through opening in rear panel and close hole

with attached cap.

NOTE: If washer is transported at later date, call your local service center to avoid suspension and structural

damage, a certified technician must properly set up washer for relocation.

+ 14 hidden pages