Marantz PV5580W, PV6080W user guide

Model PV5580/PV6080 User Guide
HD Widescreen Television
2
Once your MARANTZ purchase is registered, you’re eligible to receive all the privileges of owning a
MARANTZ product. So complete and return the Warranty Registration Card enclosed with your
purchase at once. And take advantage of these important benefits.
Return your Warranty Registration card today to ensure you receive
all the benefits you’re entitled to.
Enter below the Serial Number which is located on the rear of the cabinet. Retain this information for future reference.
Model Number: ________________________________ Serial Number: ______________________________
Know these
safety
symbols
t This “bolt of lightning” indicates uninsulated material within your unit which may cause an electrical shock. For the safety of everyone in your
household, please do not remove product covering.
s The “exclamation point” calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance
problems. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert. ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au
fond.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warranty
Verification
Registering your product within 10 days confirms your right to maximum protection under the terms and conditions of your MARANTZ warranty.
Owner
Confirmation
Your completed Warranty Registration Card serves as verification of ownership in the event of product theft or loss.
Model
Registration
Returning your Warranty Registration Card right away guarantees you’ll receive all the information and special offers which you qualify for as the owner of your model.
3
SAFETY INSTRUCTIONS - Read before operating equipment
This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Water and Moisture - The appliance should not be used near water
- for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool, etc.
6. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer.
6A. An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
6B. Tilt/Stability - All televisions must comply with recommended
international global safety standards for tilt and stability properties of its cabinet design.
Do not compromise these design standards by applying exces-
sive pull force to the front, or top, of the cabinet which could ultimately overturn the product.
Also, do not endanger yourself, or children, by placing elec-
tronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.
7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.
11. Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.
12. Cleaning - The appliance should be cleaned only as recommended by the manufacturer.
13. Power Lines - An outdoor antenna should be located away from power lines.
14. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.
Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mats and supporting structure grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the grounding electrode. See Fig. below.
15. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.
16. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.
17. Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
A. The power supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the
appliance; or
C. The appliance has been exposed to rain; or D. The appliance does not appear to operate normally or exhibits
a marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
18. Servicing - The user should not attempt to service the appliance
beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.
Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Example of Antenna Grounding as per NEC - National Electric Code
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE (NEC)
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
(NEC SECTION 810-20)
TABLE OF CONTENTS
Getting Started
Welcome/Product Registration ...................2
Safety/Precautions .....................................................3
Table of Contents.......................................................4
Features, Model and Cabinet Information.................5
On-Screen Features
PICTURE MENU
Adjusting Color, Brightness, Sharpness,
Tint, Picture, and Color Temperature Controls ..6
Using Clearview and Video Enhance Controls...7
Adjusting the TV's Convergence Control...........8
Using the Flesh Correction Control ....................9
FEATURES MENU
Using the Analog Format Screen Control.........10
Setting the TV for Closed Captioning...............11
Setting the TV for Cable or Antenna Signals....12
Adding Channels in Memory (Automatically) .13
Adding Channels in Memory (Manually).........14
Setting the TV Clock.........................................15
Using the Sleep Timer Control .........................16
Adjusting the Channel Display Control............17
Using the Time/Channel Reminder Control......18
Using Parental Control/Content Advisory:
• Code Setup/Blocking Channels...............19-20
• Content Advisory - Movie Ratings .........21-22
• Parental Guidelines.......................................23
• Blocking Options/Review Settings...............24
Using the Channel Label Control......................25
Using the Language Selection Control..............26
SOUND MENU
Adjusting Bass, Treble, and Balance Sound
Controls.............................................................27
Setting the Bass Boost Control ........................27
Setting the TV for Stereo and SAP Programs ..28
Using the Incredible Surround Control.............29
Using the Volume Display Control...................29
Using the TV Speaker On/Off Control with
the Audio Output jacks .....................................30
Surround Sound Speaker Connections and
Variable Audio Output Control ........................31
Optional Surround Sound Connections ............32
Using the TV's Audio/Video Input and
Output Jacks ...............................................33-37
Monitor (HD) Control Operation
Connection of VGA and High Definition (HD)
Component Video Equipment .................................38
Adjusting of Monitor Display Controls...................39
Remote Control Operation
Setting the Auto Picture Control.............40-41
Using the Auto Sound Control.................................42
Using the Auto Surf Control....................................43
Picture-In-Picture (PIP)
How to Use PIP (Connections) ............44-45
How to Use PIP with the TV Remote......................46
Selecting the Picture Source for PIP........................47
Adjusting PIP Color, Tint, and Size ........................48
More PIP Connections (Cable Converter)...............49
General Information
Tips if Something Isn’t Working ..............50
Glossary of TV Terms .............................................51
Index ........................................................................52
Factory Service Locations..................................53-54
Warranty ..................................................................56
Use the simple Set-Up Guide (supplied with your TV information packet) for details on:
• Antenna Hook-ups
• First Time Set-Up (Automatic Settings)
• Basic TV and Remote Control Operation
• On-Screen Menu Use
SET-UP AND QUICK USE GUIDE
2
BEGIN
1
OR
3
STOP
4
NOTE: The universal learn remote supplied with this HD PTV features a LCD window display set for a variety of accessory product functions. Due to the amount of optional components available within the remote’s Device Reference and Learn Code Lists, please refer to the separate full-use Remote Control Owner’s Manual for complete details on its use and operation.
12
1
11
2
10
3
9
4
8
5
7
6
BRIGHTNESS
PICTURE SHARPNESS SVM OFF COLOR TINT VOLUME BARON
SET-U
P ANDQUICKUSEGUIDE
HD Widescreen Television
ANTENNAOR
CABLETV
ANT(ENNA) A& B INPUTS
our TVhas two sepa-
Y
rate ANT(enna)/Cable
inputs on the rear of the
set. These two signal inputs offer convenient hook-up options for both normal TVprogram view­ing and Picture-In-Picture (PIP) features.
The ANT(enna) Ainput is intendedfor use and view-
ing on the TV’s main screen. Your home’s pri­mary Antenna, or Cable TVsignal, should be con­nected to this input for normal TVsetup, use and feature operation.
The ANT(enna) B input is a second, or auxiliary sig-
nal source, designed to
Aand B connection (using a common signal source and an optional Signal Splitter):
If yourAntenna orCable TV signal has a round cablecon­nector(75 ohm) on the end,
then you're ready to connect it to the 75ohm Signal Splitter.
If yourantenna has flat twin­lead wire (300 ohm), you first
need to attach the antenna wires to the screws on a 300 to 75 ohm adapter before connecting to the 75ohm Signal Splitter.
i
11 10 9 8
How to Use the First Time Set-Up Control ..............2
Basic TVand Remote Control Operation.................3
Basic TVand Remote Control Operation.................3
How to Use the Onscreen Menu Controls.................4
WARNING: TO PREVENTFIRE OR SHOCK HAZARD DO NOTEXPOSE THIS UNITTO RAIN OR EXCESSIVE MOISTURE.
Atypical ANT(enna)
300 to 75ΩAdapter (483521827003)
Twin Lead
Wire
Round Cable 75ΩOhm
Getting Started
12 1
2 3 4
Warning/Precautions..................................1
5 7 6
Hooking Up Your TV................................1
Connect yourAntenna or
Cable TVsignal to the single
75 ohm input plug on the two­way Signal Splitter (optional). Then connect two lengths of RF Coaxial Cable to the two Output plugs on the two-way Signal Splitter (F-type connector on both ends).
Combination VHF/UHFAntenna
- Outdoor or Indoor Antenna -
receives normal broadcast channels
2-13 (VHF) and 14-69 (UHF).
TABLEOF CONTENTS
• For details on product registration, warranty,
NOTE: This owner's manual is used with several different television models. Not all features (and drawings) dis­cussed in this manual will necessarily match those found with yourtelevision set. This is normal and does not require you contacting yourdealeror requesting service.
Connect the twin Output
plugs on the Signal Splitter to
the ANTAand ANT B inputs on the rear of the TV. Push the round connector end of the RF Coaxial Cable onto the ANT(enna) plug and screw it down tight (if using threaded cables).
and service refer to the other literature included with your TVinformation packet. Please retain all these materials and keep them handy for future reference.
SMART HELP
Note: Your HD Widescreen model TVis also capable for connec­tion and use with digital signal Set Top Box providers. These optional Advanced Television Systems Committee (ATSC) equipment convert-
Back of TV
ers can be used to display digital broadcast system programming on your High Definition ready Widescreen TV. Be sure to set the TVfor the type sig­nal you've connect­ed (see "SETUP" on page 2 of this Guide.)
First Time Set Up - automatically sets the TV for local channels, the correct picture signal (antenna or cable), and assists in the setting of TV’s Guide Plus+ feature.
Infrared Remote Control - operates your TV set and a variety of wireless remote control VCRs, Cable TV Converters, and other accessory equipment.
Standard TV broadcast (VHF/UHF) or Cable TV (CATV) channel capability as well as advanced
connectivity for high definition video and VGA. Closed Captioning - allows the viewer to read TV
program dialogue or voice conversations as on-screen text.
Automatic Programming of channels - for quick and easy selection of favorite stations available in your area.
Picture-In-Picture (PIP) - can show a TV program and the direct video output from an accessory (VCR, etc.) onto the TV screen at the same time.
Parental Control for “Censoring” - this feature can block out channels to keep children from watching undesirable programming. Parental Guideline and Movie Rating settings can also be used as part of the new Content Advisory Data system available with TV programming.
Stereo TV - with a built-in audio amplifier and a twin speaker system, reception of TV programs in both broadcast stereo sound or (SAP) bilingual broadcast are available.
Twin Antenna (A/B) Inputs - for easy displaying of two separate signal sources on the TV. An A/B button on the remote control switches the TV’s Main screen between the two Antenna (A & B) Input options.
Audio/Video Jacks - for direct connections with VCRs (and other accessories) for quality TV picture and sound playback.Component Video Input connectors are also available for high fidelity color and picture resolution when using digital video source material, such as DVD.
Surround Sound - this TV set contains external; audio speaker connections for a more dynamic sound effect capable within the today’s Home Cinema environment.
Sleep-Timer - automatically turns the TV OFF at preset time intervals.
Smart/Auto Button - for the control of TV Sound and Picture levels. Use the Smart/Auto Button on the remote to quickly select various audio modes matched to specific types of TV programming; to select video level adjustments for a variety of program sources; and to make quick one button channel selection of up to 10 of your favorite channels.
FEATURES
As you unpack your TV please note that the following items have been included with your set:
• Owner's Manual
- Safety Tip Information
- Factory Service Center Locations
• Warranty Registration Card
• Remote Control Transmitter
• Batteries for Remote Control Use Refer to the back of this manual for instructions
on the cleaning and care of the TV.
5
End-of-Life disposal
Your new projection television and its packaging contain materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and minimize the amounts which need to be properly disposed.
Your product also uses batteries which should not be thrown away when depleted, but should be handed in and disposed of as small chemical waste.
Please find out about the local regulations on how to dispose of your old television, batteries, and packaging materials whenever you replace existing equipment.
High Definition Digital - Projection Television capable of 1500x1080i interlaced imaging for superior resolution and performance. Line doubling circuitry and video processing technology able to output progressive scan material with clean, stable widescreen images. Triple lens system matched to first surface mirror and fine pitched lenticular screen methods which amounts to an incredible 1,620,000 pixels of display capability. High Definition Component and RGB Inputs are available as well for Y, Pb, Pr; horizontal/vertical sync, and RGB/VGA monitor input operation modes.
Automatic Phosphor Aging Compensation (APAC)
- Automatic incremental shifting of TV screen
elements to prevent any onscreen image outline retention or “screen burn” problems.
GUIDE Plus+®- Electronic TV Program guide which provides for daily television channel listings, descriptions of program content, sorting of shows by subject themes, and a variety of other VCR programming options. (See your separate GUIDE Plus+®Owner’s Manual for further details.)
Because of continuous product improvements, the information mentioned in the documents accompanying your product are subject to change without notice.
12
1
11
2
10
3
9
4
8
5
7
6
PICTURE MENU CONTROL ADJUSTMENTS
COLOR, BRIGHTNESS,
SHARPNESS, TINT, PICTURE
T
o adjust your TV color and
picture controls, select a TV channel and follow the steps shown below:
Select BRIGHTNESS, PICTURE, COLOR, TINT, or SHARPNESS picture control.
With the PICTURE MENU on screen, move the RED highlight with the outer OK arrow
buttons. Then press the center OK button to select the feature.
Press the OK arrow
buttons to adjust the selected control.
Press the STATUS button to
clear the screen.
1
2
3
SMART HELP
Remember. When the bar
scale is centered, control settings are at normal mid-range levels.
BRIGHTNESS Press (-) or (+) until dark parts of the picture show good detail.
PICTURE Press (-) or (+) until whitest parts of the picture are as bright as you prefer.
COLOR Press (-) or (+) to add or eliminate color.
TINT Press (-) or (+) to obtain natural skin tones. (Also see Flesh Correction on page 9 for more information).
SHARPNESS Press (-) or (+) to improve detail in the picture.
Select and then press MENU (M) button to view additional controls grouped under same feature heading. For Example: Tint, Brightness, Picture, etc.
6
OK
Note: A Color Temperature control is also available to set the level or degree of color intensity (especially on white picture screen elements). For example, use the Color Temperature (Picture Menu 3 of 3) for the following settings:
COOL – makes whites, bluish NORMAL – keeps whites, white.
WARM – makes whites, reddish.
PICTURE MENU
EXIT
3 OF 3
COLOR TEMPERATURE
MORE...
EXIT
NORMAL
WARM
COOL
COLOR TEMPERATURE
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
OFFON
ON/OFF
DSS/ VCR2
TUNER
D1
D2
D3
D4
CLONE MACRO MODE
LEARNING REMOTE CONTROL
RC-18SR
LD DVD
TV
AUX
TAPE
CD
D5
D6
D7
D8
VCR1
CD-R
/MD
VOLCH
MACRO MACRO
1
2
1
3
2
1 4 7
M
PIP
OK
6
5
9
8
C
0
MUTE
GUIDEAMP
3
4
SOUND
EXIT
1
PICTURE MENU
COLOR TINT
BRIGHT
SHARP
EXIT
PICTURE
CLEARVIEW
MORE...
1 OF 3
3
COLOR
MIN
EXIT
MAX
NEXT...
2
PICTURE MENU CONTROLS (CONTINUED)
C
learview is a sharpness feature
which smoothes out background snow (or picture noise) without losing picture image detail or crispness.
Select CLEARVIEW control.
With the PICTURE MENU on screen, move the RED highlight with the outer OK arrow
buttons. Then press the center OK button to select the feature.
Press the outer OK arrow
buttons to move the RED highlight. Press the center OK button to select (
U) the ENHANCED mode.
Press the STATUS button to
clear the screen.
CLEARVIEW
1
2
3
7
Note: An additional Picture Menu “VIDEO ENHANCEMENT” control (similar in function and use as the Sharpness control) is also available to further improve picture intensity and detail, particularly for the playback of DVD player source material. Selection and adjustment of the Video Enhancement control (Picture Menu 2 of 3) is the same as with other Color and Picture Menu control options.
PICTURE MENU
FLESH CORRECTION
EXIT
2 OF 3
MORE...
CONVERGENCE
VIDEO ENHANCEMENT
EXIT
MIN
MAX
VIDEO ENHANCEMENT
OK
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
OFFON
ON/OFF
DSS/ VCR2
TUNER
D1
D2
D3
D4
2
CLONE MACRO MODE
LEARNING REMOTE CONTROL
RC-18SR
LD DVD
TV
AUX
TAPE
CD
D5
D6
D7
D8
VCR1
CD-R
/MD
VOLCH
MACRO MACRO
1
2
1
3
2
1
5
4
POSITIONDNPIP
7
8
M
0
OK
6 9 C
MUTE
GUIDEAMP
SOUND
EXIT
3
4
PICTURE MENU
COLOR TINT
BRIGHT
SHARP
EXIT
PICTURE
CLEARVIEW
MORE...
1 OF 3
3
CLEARVIEW
NORMAL
ENHANCED
EXIT
1
2
NEXT...
PICTURE MENU CONTROLS (CONTINUED)
RED/BLUE CONVERGENCE
C
onvergence is the correct
lining up of the red and blue light paths on the TV screen. NOTE: If no color fringing (see Smart Help) shows, then no Convergence adjustments are necessary for your TV.
Select CONVERGENCE
control. With PICTURE MENU (2 of 3) on
screen, move the RED highlight with the outer OK arrow
buttons. Then press the center OK button to select the feature.
If there is RED or BLUE color
fringing (see note below) on your TV, press the outer OK arrow buttons to move the highlight. Press the center OK button to select the Align Red or Align Blue Convergence control.
Press the OK arrow
buttons to move the red or blue
cross directly over the white cross on the TV screen.
The red or blue cross is properly adjusted when it is completely merged with the white cross. (No color appears around the edge of the white cross).
Press the STATUS button to
clear the screen when convergence adjustments are complete.
1
2
3
SMART HELP
Remember. Convergence
has been set at the factory for best viewing, but if one or more of the (red or blue) colors appear around the edges of objects (color fringing) follow the steps given in this section.
4
8
NOTE: Adjustments for “Multi-Point” on-screen color fringing can also be made as part of the TV’s Convergence control system. Follow the TV’s on-screen menu directions to select individual screen areas that can be readjusted and set for varying red/blue color fringing conditions. These multi-point settings can then be “Saved” to memory for the specific areas of the TV screen (or Factory Settings for convergence can be recalled and put back into place for use).
CONVERGENCE MULTI POINT CONVERGE RED POINTS
CONVERGE BLUE POINTS RESTORE FACTORY SETTINGS SAVE ADJUSTMENTS BACK
CONVERGE RED POINTS
USE TO ADJUST
DIGIT 2, 4, 6, 8 TO MOVE CURSOR
PRESS MENU TO RETURN
PRESS MENU NOW TO CONTINUE
MULTI-POINT
CONVERGENCE
OK
OK
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
ON/OFF
1
DSS/
VCR2
TUNER
D1
D2
D3
D4
CLONE MACRO MODE
LEARNING REMOTE CONTROL
RC-18SR
LD DVD
TV
TAPE
CD
MACRO MACRO
2
SOUND
OFFON
D5
D6
D7
D8
VCR1
CD-R
AUX
/MD
3
4
EXIT
PICTURE MENU
COLOR TINT
BRIGHT
SHARP
EXIT
4
PICTURE MENU
CONVERGENCE
FLESH CORRECTION
VIDEO ENHANCEMENT
EXIT
PICTURE
CLEARVIEW
MORE...
1 OF 3
MORE...
2 OF 3
2
VOLCH
1
3
2
1
POSITIONDNPIP
5
4
8
7
0
M
OK
6 9
C
MUTE
GUIDEAMP
1
2
3
CONVERGENCE MENU ALIGN RED
ALIGN BLUE CONVERGE MULTI POINT BACK
PRESS TO ALIGN RED PRESS MENU TO RETURN
U
se the Flesh Correction
control to keep skin tone hues (or facial tint) from varying from TV channel to TV channel.
Select FLESH
CORRECTION control.
With PICTURE MENU (2 of 3) on screen, move the RED highlight with the outer OK arrow
buttons. Then press the center OK button to select the feature.
Press the OK arrow
buttons to move the RED
highlight. Press the center OK button to turn (
U) the FLESH
CORRECTION control ON.
Press the STATUS button to
clear the screen.
FLESH CORRECTION
1
2
3
PICTURE MENU CONTROLS (CONTINUED)
9
OK
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
1
2
DSS/
VCR2
TUNER
D1
D2
D3
D4
CLONE MACRO MODE
LEARNING REMOTE CONTROL
TV
CD
MACRO
2
1
2
1
POSITIONDNPIP
5
4
POSITIONDNPIP
8
7
0
M
ON/OFF
RC-18SR
LD DVD
TAPE
3 6 9
C
SOUND
PICTURE MENU
EXIT
OFFON
MACRO
D5
D6
D7
D8
VCR1
CD-R
AUX
/MD
VOLCH
OK
MUTE
GUIDEAMP
3
3
4
1
2
COLOR TINT
BRIGHT
SHARP
EXIT
PICTURE MENU
CONVERGENCE
FLESH CORRECTION
VIDEO ENHANCEMENT
EXIT
FLESH CORRECTION
ON
OFF
PICTURE
CLEARVIEW
MORE...
1 OF 3
MORE...
2 OF 3
EXIT
FEATURE MENU CONTROL ADJUSTMENTS
ANALOG FORMAT
Y
our TV is able to deliver
lifelike, widescreen picture (or “home cinema” experience) that is promised with High Definition TV viewing. The Analog Format control can be used to expand conventional 4:3 aspect ratio (width-to-height) broadcasts in order to fit your TV’s widescreen format; or to reset the screen to best match the current programming.
Select ANALOG FORMAT
control.
With the FEATURES MENU on screen, move the RED highlight with the outer OK arrow buttons. Then press the center OK button to select the feature.
Press the OK arrow
buttons to move the RED
highlight. Press the center OK button to select (U) the desired screen aspect ratio or screen display control.
Press the STATUS button to
clear the screen.
1
2
3
10
Note: The LCD Display MODE 2 screen on the remote control can also be used to quickly select various aspect ratio screen control settings for TV viewing. Press the LCD screen direction (< or >) buttons on the remote to select the WideTV Mode 2 display for use. Then press the correct (D) callout button to select the desired screen aspect ratio. Note: Not all of the MODE 2 LCD display settings may be available for use with your select model HD PTV.
SMART HELP
Note: In the past the
relationship between a TV screen’s width to height, or aspect ratio, has historically been 33% wider than the picture screen height (or a 4:3 aspect ratio). The widescreen format of your TV screen is nearly 80% greater than its measure height (which accounts for a 16:9 aspect ratio). The reason for the 16:9 aspect ratio screen is that it allows for the dramatic and lifelike viewing of original version movies and cinemas (similar to the type found in your local theaters). And the 16:9 aspect ratio widescreen is also a good visual match for how our eyes work in a horizontally oriented field of view and action plane.
OK
OK
Panoramic - Conventional picture is expanded to fill the full 16:9 aspect ratio screen area. Most of the non-linear picture expansion is performed toward the outer edges so that correct proportions are retained in the center of the screen.
4:3 (Standard) ­Conventional TV picture format shows on the screen. Black bar areas show on the side margins of the screen.
16:9 (Expand) - Full widescreen mode with linear expansion to view HD program broadcasts. Used for material originally produced in 16:9 format.
Theater 1/2 - Expanded zoom modes with picture images increased in magnification. Designed for use with “letterbox” or cropped movie images such as found with Cinemascope or Cinerama type program material. Note: With the Theater modes there can be some loss of information at the edges as the picture expands to fill the screen.
Building Trade News
Building Trade News
Building Trade News
Building Trade News
PANORAMIC
4 X 3
16 X 9
THEATER 1/2
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
LEARNING REMOTE CONTROL
D1
D2
D3
D4
DSS/ VCR2
TUNER
CLONE MACRO MODE
TV
CD
MACRO
1
2
ON/OFF
RC-18SR
LD DVD
TAPE
SOUND
FEATURE MENU
ANALOG
EXIT
OFFON
MACRO
D5
D6
D7
D8
VCR1
CD-R
AUX
/MD
3
3
4
FORMAT
CLOSED
CAPTIONS
EXIT
ANALOG FORMAT
PANORAMIC 4 X 3 16 X 9 THEATER 1 THEATER 2
EXIT
CABLE
TUNING
CHANNEL
MEMORY
MORE...
1 OF 5
2
VOLCH
1
3
2
1
POSITIONDNPIP
5
4 7
8 0
M
OK
6 9
C
MUTE
GUIDEAMP
2
1
C
losed Captioning (CC) allows
you to read the voice content of television programs on the TV screen. Designed to help the hearing impaired this feature uses on-screen "text boxes" to show dialogue and conversations while the TV program is in progress.
Select CLOSED
CAPTIONING control.
With the FEATURES MENU on screen, move the RED highlight with the outer OK arrow buttons. Then press the center OK button to select the feature.
Press the OK arrow
buttons to move the RED highlight.
Press the center OK button to select (U) the desired Closed Caption mode - For Example: "ALWAYS ON" and "CAPTION 1".
CAPTION 1, 2, 3, 4:
dialogue (and descriptions) for the action on the captioned TV program shows on-screen. (See Important Note on this page.)
TEXT 1, 2, 3, 4:
often used for channel guide, schedules, or bulletin board information for CC programs.
After making your Caption mode
selection, press the STATUS
button to clear the TV screen. The selected Closed Caption mode will be active.
To cancel, set the Closed Captioned feature to OFF when finished.
1
2
FEATURE MENU CONTROLS (CONTINUED)
NOTE: Not all TV programs and product commercials are made for broadcast
with Closed Caption (CC) information included. Neither are all Closed Caption modes (CAPTION 1-4; or TEXT 1-4) necessarily being used by a broadcast station during the transmission of a closed caption program. Usually "CAPTION 1" is the most used mode to view captioned material. Refer to your area's TV program listings for the stations and times of Closed Caption shows.
3
CAPTION 1 mode
Example Screen Display
FULL SCREEN TEXT
will block TV screen from viewing
Closed Caption information will usually appear in black and white (although some broadcasters or networks may occasionally use color to highlight or draw attention to certain areas.)
CLOSED CAPTION
NOTE: The ON DURING MUTE ONLY control can be
used to set the TV to turn the Closed Caption mode "ON" whenever the MUTE button on the remote is pressed.
SMART HELP
Remember. Broadcast
stations will often use spelling abbreviations, symbols, dropouts and other grammatical shortcuts in order to keep pace with the on-screen action. These type factors vary upon the source of the captioned text material and do not indicate a need for service on the part of the TV.
11
OK
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
MACRO
LEARNING REMOTE CONTROL
1
2
D1
D2
D3
D4
DSS/
TV
VCR2
CD
TUNER
2
POWER
SOURCE
OFFON
ON/OFF
CLONE MACRO MODE
RC-18SR
LD DVD
AUX
TAPE
D5
D6
D7
D8
VOLCH
VCR1
MACRO
CD-R
/MD
SOUND
EXIT
3
4
3
FEATURE MENU
ANALOG FORMAT
CLOSED
CAPTIONS
EXIT
CLOSED CAPTION
ALWAYS ON ALWAYS OFF ON DURING MUTE ONLY
CAPTION 1 CAPTION 2 CAPTION 3 CAPTION 4
EXIT
CABLE TUNING
CHANNEL
MEMORY
MORE...
1 OF 5
TEXT 1 TEXT 2 TEXT 3 TEXT 4
1
3
2
1
POSITIONDNPIP
5
4
8
7
0
M
OK
6 9 C
MUTE
GUIDEAMP
1
2
JOHN: Why did they move the meeting up to this week? MARSHA: I don't know, but they are pushing to close the deal.
CLOSE CAPTION PROGRAMS ON WXYZ
ALL ITEMS ARE EASTERN STANDARD TIME (EST)
CHECK LOCAL LISTINGS
FOR TIMES IN YOUR AREA
6:00 TOP OF THE MORNING
10:00 THE BEST LITTLE CALL-IN SHOW EVER
12:00 NOONDAY NEWS
1:30 AS YOUR LIFE TURNS MY WORLD AROUND 6:00 WORLD NEWS FOR TODAY
9:00 PLAYHOUSE MOVIE OF THE WEEK
FEATURE MENU CONTROLS (CONTINUED)
Y
ou need to make sure the TV is
set to pick up either Cable TV or Antenna signals. In other words, the TV needs to know if you connected a Cable TV signal or a normal antenna to its ANTENNA plug.
NOTE: If you went through First Time Setup (in your Quick Use Guide), this task has already been completed for you.
Select CABLE CHANNEL
TUNING control.
With the FEATURES MENU on screen, move the RED highlight with the outer OK arrow buttons. Then press the center OK button to select the feature.
Press the OK arrow
buttons
to move the RED highlight. Press the center OK button to select (U) the desired mode - For Example: CABLE.
CABLE- If you DO have
Cable TV
connected to the TV. Channels 1-125 available.
NORMAL- If you have an
Antenna connected
to the TV. Channels 2-69 available.
Press the STATUS button to
clear the screen.
CABLE TUNING
1
2
3
12
Note: Both ANT(enna) A and ANT B inputs on the rear of the TV can be set for the correct connected signal (either an Antenna or Cable TV source).
OK
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
OFFON
ON/OFF
DSS/
VCR2
TUNER
D1
D2
D3
D4
CLONE MACRO MODE
LEARNING REMOTE CONTROL
RC-18SR
LD DVD
TV
AUX
TAPE
CD
D5
D6
D7
D8
VCR1
CD-R
/MD
MACRO MACRO
1
2
SOUND
EXIT
3
4
FEATURE MENU
ANALOG FORMAT
CLOSED
CAPTIONS
EXIT
3
CABLE TUNING
CABLE ANT A NORMAL ANT A
CABLE ANT B NORMAL ANT B
CABLE
TUNING
CHANNEL MEMORY
MORE...
1 OF 5
2
1
2
1
POSITIONDNPIP
5
4 7
8
M
0
VOLCH
3
OK
6 9
C
MUTE
GUIDEAMP
1
2
EXIT
Y
our TV can automatically set itself
for local area (or Cable TV) channels. This makes it easy for you to select only the TV stations in your area when the CHANNEL
▲▼
buttons are pressed. NOTE: If you went through First
Time Setup (in your Quick Use Guide), this task has already been completed for you.
Select CHANNEL MEMORY
(START AUTO-PROGRAMMING)
control. With the FEATURES MENU on
screen, move the RED highlight with the outer OK arrow buttons. Then press the center OK button to select the feature.
Press the center OK button to
turn AUTO-PROGRAMMING ON .
The TV shows which channel numbers are "SAVED" (U) as they are added into memory.
"Auto-programming CHANNEL MEMORY is finished" shows when the TV is through adding channels.
Press the STATUS button to clear
the screen.
CHANNEL MEMORY
AUTO-PROGRAMMING
1
2
3
FEATURE MENU CONTROLS (CONTINUED)
U Channel Numbers are Saved in Memory
SMART HELP
Try it out. Press the
CHANNEL▲▼ buttons
and see which channels you can select.
Remember, an Antenna or Cable TV signal must first be connected to your TV so that channels can be saved.
If you want to delete any unwanted channels from the TV's memory, see "ADD/DELETE CHANNELS" on the next page.
13
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
SOUND
EXIT
FEATURE MENU
ANALOG FORMAT
CABLE
TUNING
MACRO
LEARNING REMOTE CONTROL
1
2
D1
D2
D3
D4
DSS/ VCR2
TUNER
2
1
POSITIONDNPIP
4 7 M
POWER
SOURCE
ON/OFF
CLONE MACRO MODE
RC-18SR
TV
TAPE
CD
1
3
2
6
5
9
8
C
0
LD DVD
CLOSED
CAPTIONS
EXIT
OFFON
MACRO
D5
D6
D7
D8
VCR1
CD-R
AUX
/MD
VOLCH
OK
MUTE
GUIDEAMP
3
3
4
1
CHANNEL MEMORY
ADD/DELETE CHANNELS
START AUTO-PROGRAMMING
EXIT
AUTO-PROGRAMMING CHANNEL
MEMORY FOR ANT A
1 2 3 4 5 6 7 8 9 1O 11 12
13 14 15 16 17 18 19 20 21 22 23 24
Press "M" to
Stop Auto-Program
CHANNEL
MEMORY
MORE...
1 OF 5
FEATURE MENU CONTROLS (CONTINUED)
A
uto-Programming (see
previous page) adds all the channels it can find (on your Antenna or Cable TV system) into the TV's memory. Add/Delete Channels makes it easy for you to add other channels, or drop unwanted channels, from the list of channels in the TV's memory.
Select CHANNEL MEMORY
(ADD/DELETE CHANNELS)
control. With the FEATURES MENU on
screen, move the RED highlight with the outer OK arrow buttons. Then press the center OK button to select the feature.
Press the CHANNEL ▲▼ or
number buttons to select the
channel you want to add or delete.
Press the outer OK arrow
button (on the Right) to ADD the
channel into the TV's memory. Press the outer OK arrow button
(on the Left) to DELETE the channel from memory.
Repeat steps 2 and 3 for each channel you wish to add or delete.
Press the STATUS button to
clear the screen when through.
ADD/DELETE CHANNELS
1
2
3
4
SMART HELP
Remember. A separate
ADD/DELETE CHANNEL memory may also be created for the ANT(enna) B Input on the rear of the set (if an Antenna or Cable TV signal has been connected). Press the “SOURCE” button on the remote, while in the ADD/DELETE CHANNEL mode, to switch between the ANT A and ANT B channel memory lists. Then follow steps 2 and 3 as shown to the left to add or delete the desired channels.
14
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
ON/OFF
DSS/ VCR2
TUNER
D1
D2
D3
D4
CLONE MACRO MODE
LEARNING REMOTE CONTROL
RC-18SR
LD DVD
TV
TAPE
CD
MACRO MACRO
1
2
SOUND
OFFON
D5
D6
D7
D8
VCR1
CD-R
AUX
/MD
3
4
EXIT
FEATURE MENU
ANALOG
FORMAT
CLOSED
CAPTIONS
EXIT
CABLE
TUNING
CHANNEL
MEMORY
MORE...
1 OF 5
4
CHANNEL MEMORY
ADD/DELETE CHANNELS
START AUTO-PROGRAMMING
EXIT
2
1
2
1
POSITIONDNPIP
5
4
8
7
C
0
M
VOLCH
3
OK
6 9
MUTE
GUIDEAMP
1
3
ADD/DELETE CHANNEL
Channel 19 Added for ANT A
SELECT CHANNEL to DELETE CHANNEL
SOURCE
for ANT B
when FINISHED
M
FEATURE MENU CONTROLS (CONTINUED)
SET CLOCK
Y
our TV comes with an on-
screen clock. During normal operation the clock appears on the screen with every channel change (and when the STATUS button is pressed).
Select SET CLOCK control.
With the FEATURES MENU (2 of
5) on screen, move the RED highlight with the outer OK arrow buttons. Then press the center OK button to select the feature.
Press the remote's number
buttons to set the time clock.
Press the STATUS button to
set the clock in operation and clear the screen.
1
2
3
Remember, be sure to
press "0" first and then the hour number for single digit entries.
The remote's OK arrow buttons can also be used to set the hours, minutes and AM/PM portions of the clock.
TV Clock settings may be lost when the TV is unplugged (or AC power to the set is interrupted).
SMART HELP
15
OK
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
ON/OFF
DSS/ VCR2
TUNER
D1
D2
D3
D4
CLONE MACRO MODE
LEARNING REMOTE CONTROL
RC-18SR
LD DVD
TV
TAPE
CD
MACRO MACRO
1
2
1
3
2
1
POSITIONDNPIP
6
5
4
9
7
8
C
0
M
2
FEATURE MENU
ANALOG
SOUND
EXIT
OFFON
3
3
4
D5
D6
D7
D8
VCR1
CD-R
AUX
/MD
VOLCH
OK
MUTE
GUIDEAMP
1
FORMAT
CLOSED
CAPTIONS
EXIT
FEATURE MENU
SET
CLOCK
HALF HOUR
REMINDER
EXIT
PLEASE ENTER THE
CURRENT HOUR
SET CLOCK
9 : 19 AM
CABLE
TUNING
CHANNEL
MEMORY
MORE...
1 OF 5
PARENTAL
CONTROL
CHANNEL
DISPLAY
MORE...
2 OF 5
FEATURE MENU CONTROLS (CONTINUED)
H
ave you ever fallen asleep in
front of the TV only to have it wake you up at two in the morning with a test pattern screeching in your ears? Well, your TV can save you all that trouble by automatically turning itself off.
Press the SLEEP button on the
remote control (LCD Display Mode 1 screen - D6 button).
Press the SLEEP button
repeatedly to pick the amount of time (15 minutes to 2 hours ahead) before the TV will turn itself off.
Press the STATUS button to
clear the screen after you have set the time for the TV to turn off.
1
2
3
Remember, to see how
many minutes are left before the TV shuts itself off, reselect the SLEEP TIMER control screen.
To stop a SLEEP TIMER setting, reset the timer back to OFF. (Turning the TV off and on, or pressing a button during the last minute of a timer setting, will also cancel a setting.)
A few seconds before the TV is to shut off a message will come on the screen telling you GOOD NIGHT.
SMART HELP
SLEEP TIMER
16
SET SLEEP TIMER
1 : 15
PRESS "SLEEP" TO CHANGE
POWER
SOURCE
OFFON
ON/OFF
LEARNING REMOTE CONTROL
DN
D1
D2
D3
D4
DSS/ VCR2
TUNER
1 4 7
M
CLONE MACRO MODE
RC-18SR
TV
CD
2
6
5
9
8
C
0
LD DVD
TAPE
3
AUX
MACRO
1
2
MACRO
D5
D6
D7
D8
VCR1
CD-R
/MD
VOLCH
OK
MUTE
GUIDEAMP
3
3
4
1
2
FEATURE MENU CONTROLS (CONTINUED)
W
ith the Channel Display
control you can change the size and location of the on screen channel and clock information.
Select CHANNEL DISPLAY
control. With the FEATURES MENU (2
of 5) on screen, move the RED highlight with the outer OK arrow buttons. Then press the center OK button to select the feature.
Press the OK arrow and
center OK buttons to highlight
and select (
U) the LARGE or
SMALL display control.
Press the STATUS button to
clear the screen.
CHANNEL DISPLAY
1
2
3
17
SMART HELP
Try it out. Press the
CHANNEL ▲▼ buttons and
you should see the Display Size you selected.
Remember. The SMALL SIZE display shows only the channel number, not the time (or clock).
OK
MAIN MENU
PICTURE
FEATURES
1ST TIME SETUP
POWER
SOURCE
ON/OFF
MACRO
1
2
CLONE MACRO MODE
LEARNING REMOTE CONTROL
RC-18SR
D1
D2
D3
D4
FEATURE MENU
ANALOG
SOUND
EXIT
OFFON
MACRO
D5
D6
D7
D8
3
3
4
FORMAT
CLOSED
CAPTION
EXIT
FEATURE MENU
SET
CLOCK
HALF HOUR
REMINDER
EXIT
CABLE
TUNING
CHANNEL
MEMORY
MORE...
1 OF 5
PARENTAL
CONTROL
CHANNEL
DISPLAY
MORE...
2 OF 5
DSS/
TV
VCR2
CD
TUNER
2
1
2
1
POSITIONDNPIP
5
4 7
8 0
M
LD DVD
TAPE
3 6 9
C
VCR1
CD-R
AUX
/MD
VOLCH
CHANNEL DISPLAY
LARGE
OK
MUTE
GUIDEAMP
1
2
SMALL - Channel/Label
EXIT
Loading...
+ 39 hidden pages