Liebherr LTF 1060-4.1 User Manual

Truck Mounted
Telescopic Crane

LTF 1060-4.1

Max. capacity: 60 t
Max. lifting height: 56 m
Max. radius: 48 m

Truck mounted telescopic crane LTF 1060-4.1
Economical and flexible

With a long telescopic boom and high capacities the compact truck mounted telescopic crane
LTF 1060-4.1 from Liebherr on a standard truck chassis is an economical and flexible alter­native in the taxi crane class. It drives on public roads with complete equipment and thus is
immediately ready for operation on the job site.

2

LTF 10 60 - 4.1

• 40 m long telescopic boom

• High capacities with full and part ballast

• Low axle loads, flexible registration possibilities

• Flexible crane control LICCON2 with mobile and multifunctional control and display
unit BTT

• Optional available wireless remote control, with which all crane movements outside
of the cab can be operated

• Low operating costs in driving mode due to use of standard trucks

• Fuel saving by separate crane engine specifically adapted for crane operations

LTF 10 60 - 4.1

3

4

Extensive storage boxes for equipment
and support timber are provided at the
intermediate frame and the two front
folding beams

LTF 10 60 - 4.1

Mobility and functionality

Economical truck chassis

The operational costs of the LTF 1060-4.1 are low due to the use of a standard
truck chassis. Cost advantages result from the design related reduced fuel con­sumption and economical tyres and spare parts, because they are produced
in large quantities. Optional available are additionally roomy, comfortable truck
driver cabs with sleeping cabin. They offer flexibility on jobs and possibilities for
relaxing for the driver.

Special self produced
Liebherr intermediate frame

The connection to the crane chassis was designed by Liebherr using MSH­profiles from high tensile fine grain steel. Crane drivers appreciate the numerous
storage compartments in the area of the intermediate frame and the outrigger
beams.

Storage boxes for lifting tackle

LTF 10 60 - 4.1

5

6

The crane cab

• Large field of vision

• Safety glasing

• Tinted screens

• Crane driver seat with lumbar support,
multiple adjustable

• Heat and noise insulated interior lining

• Corrosion resistant

• Working flood lights

• 20° tiltable to the rear

LTF 10 60 - 4.1

Comfort and variability

Fast, secure and variable erection

The support, the ballast mounting as well as the installation of additional equip­ment is designed for speed, safety and comfort. For the safety of the opera­tional staff steps and handholds are provided.

The supports

• 4 point support

• Horizontally and vertically fully
hydraulically extendable

• Stroke of the support cylinders
750 mm

• Illumination of the support area by
4 integrated flood lights

• Outrigger beams 2-stage, fully hy­draulic, low maintenance extension
system

Supporting the crane –
fast, comfortable and safe

• BTT Bluetooth Terminal, mobile
control and display unit

• Fully automatic levelling by pressing
a push button

• Engine start/stop and speed
regulation

LTF 10 60 - 4.1

7

EURO 6

Chassis VolvoChassis Scania

10.2 t ballast

Total weight: 42 t

5 t ballast

9 t 9 t 12 t 12 t

9.2 t ballast

9 t 9 t

Total weight: 42 t

5 t ballast

Total weight: 38 t

0 t ballast

Total weight: 32 t

< 9 t < 9 t ≤ 10 t ≤ 10 t

< 9 t < 9 t < 10 t < 10 t

< 9 t < 9 t

Total weight: 38 t

0 t ballast

< 9 t < 9 t

Total weight: 33 t

0.6 t

1.6 t

8

1.0 t

2.0 t

Basic ballast 10.2 t

5.0 t

LTF 10 60 - 4.1

EURO 6

Flexible drive conditions

Alleviated registration possibilities

For mobility and flexibility serve the compact dimensions and low axle loads of
the truck mounted telescopic cranes. The LTF 1060-4.1 meets for instance the
conditions for an unlimited driving permission in Germany.

Low axle loads

12 t 12 t

≤ 10 t ≤ 10 t

As a taxi crane with 5 t ballast the LTF 1060-4.1 has a total weight of 38 t. There­by the two front axles are loaded with 9 t and the rear axles with 10 t each. By
reducing the carried ballast the total weight can be limited to 33 t.

Ballast mounting – only a matter of minutes

• Multiple number of ballast variations

• Fast ballasting with keyhole technology from the crane cab

• Compact ballast dimensions, only 2.55 m ballast width

• Tail radius only 3.5 m

< 10 t < 10 t

Variable ballast

LTF 10 60 - 4.1

9

10

The fully automatic telescoping system „TELEMATIK“

• Increase of capacities at long booms and wide radii due to
“light” telescoping system

• 1-stage hydraulic cylinder with hydraulically operated catch
pin

• Maintenace free telescoping system

• Telescoping fully automatically

• Most simple operation, monitoring of the telescoping
action at the LICCON screen

LTF 10 60 - 4.1

High capacities and flexible boom system

Powerful, strong telescopic boom and
functional lattice extension

The telescopic boom consists of the heel section and 4 telescopic sections,
which are comfortably and automatically extended and pinned to the requested
lengths by the thousand-fold proven single cylinder telescoping system TELE­MATIK.

• 40 m long telescopic boom

• 9.5 m – 16 m long double swing-away jib, under 0°, 20° or 40° mountable

• The swing-away jib is identical to the jib of the LTM 1055-3.2; by this modu­lar design the swing-away jib can be used on both crane types

High capacities with full ballast as well as with
part ballast offer a wide operational field

• High side stability due to the oval boom profile

• Optimized capacities by multiple extension variants

• Capacity 10.4 t at 40 m long telescopic boom

2.5 m long assembly jib

High capacities at unpinned telescope lengths

• High telescopable capacities by interpolation

• Separate load charts for holding of loads at unpinned telescope lengths

• Display at LICCON-monitor

Holding capacity

Unpinned telescope lengths

Telescopable load

LTF 10 60 - 4.1

11

12

The hoist gear

• Liebherr hoist winch with integrated
planetary gear and spring loaded
multiple disk brake

• Rope pull 45 kN on the outer layer

• Max. rope speed 111 m/min

• 2. hoist gear optional

LTF 10 60 - 4.1

Powerful crane drive

With proven components

The drive components for the crane drive are designed for high efficiency and
provide for a sensible and precise handling of the loads. They are specially
adapted for the crane operation and proven in severe long-time tests.

• Crane engine: 4-cylinder Liebherr turbo charged diesel engine,
129 kW/175 HP, max. torque of 815 Nm, optimized fuel consumption
by electronic engine management

• Diesel-hydraulic crane drive, open oil circuits with electric “Load Sensing“­control, 4 working motions simultaneously possible

• Electric/electronic SPS-crane control via the LICCON computer system

• Comfort armrest control with 2 self centering, 4-fold joysticks, stepless
control of all crane motions with winch and slewing gear sensors, electronic
pilot control

• Slewing gear switchable for: open or hydraulically fixed, so the motion can
optimally be adjusted for the various operation conditions, e. g. sensible
erection operation or fast working cycles

The slewing gear

• Liebherr planetary gearbox, spring
loaded multiple disk brake

• Switchable as standard: open or
hydraulically fixed

• Slewing speed of 0 – 1.7 rpm stepless
adjustable

LICCON

screen

Sensor

Control block

Liebherr diesel engine

Contro l lever with touch di splays

Luffing

cylinder

Telescoping

cylinder

Gear t ype pum p

Variable pump

The central greasing

• Standard central greasing device for
slewing ring, boom bearing, luffing
cylinder and winch bearing

• Consistent supply of grease

• Filling amount in transparent container
visible at all times

Control unit

Hoist gear Slewing gear

LTF 10 60 - 4.1

13

14

The LICCON test system

• Fast detection of faults at the screen
without metering instruments

• Display of error codes and error
description

• Comfortable dialogue functions for
monitoring of all in and out ports

• Display of the functions and allocation
of the sensors and the actors

LTF 10 60 - 4.1

Intelligent crane control

For functional and safe crane operation,
the LICCON computer system

The soft- and hardware of the mobile crane control is developed by Liebherr
in-house. The centre is the LICCON computer system (Liebherr Computed
Control).

• Integrated LML load moment limiter

• Key components are in-house manufactured by Liebherr

• Guaranteed spare parts availability

• World wide proven under the most different climate conditions

• Operator friendly

The second control generation LICCON2 is the result of a continuous develop­ment by the Liebherr specialists and enables the adaption to the constantly in­creasing demands of the markets due to its modern and future oriented control.

The data bus technology

Liebherr mobile cranes are completely interlaced by the data bus system. All
important electric and electronic components are equipped with own micro
processors and communicate with each other by only limited data cables. For
the special demands of the mobile crane Liebherr has developed own data
bus systems (LSB – Liebherr-System-Bus). The data bus technology improves
the reliability, the comfort and the safety for road driving and crane operation:

• Higher reliability due to remarkable lesser electric cables and contacts

• Continuous self testing of the “intelligent sensors“

• Comprehensive diagnosis possibilities, fast fault finding

The LICCON working range limiting system

• Relieve for the crane driver by automatically
monitoring of working area borders like
bridges, roofs, etc.

•

Simple programming

• Four different limitation functions:

- Sheave head height limitation

- Radius limitation

- Slewing angle limitation

- Edge limitation

The LICCON work planner

• Computer program for planning, simula­tion and documentation of crane jobs at
the personal computer

• Display of all load charts related to a
crane

• Automatic search for the applicable
crane by entering the load case para­meters load, radius and lifting height

• Simulation of crane jobs with drawing
function and support force display

LTF 10 60 - 4.1

15

LICCON2 – safe and comfortable

Attaching and detach­ing of the hook block

The BTT Bluetooth Terminal
offers the crane driver the possibility
to attach or detach the hook block at the
front of the vehicle within sight, as the hoist
winch and the luffing cylinder of the tele­scopic boom are remote controlled.

Wireless remote control
(option)

All crane motions can be controlled
outside of the cab.

• Higher efficiency

• Free view and closeness to the load

• Prevention of communication errors
between the crane driver and the job

Wireless remote control

site personnel

Colour monitor

The readability of the data on
the monitor of the LICCON2
control in the superstructure
cab is improved by the colour
display. Warnings and the
crane utilization are easier
detectable.

Crane supporting

With the BTT the crane is supported
comfortably and safely. Engine start/
stop and speed regulation, electronic
inclination display and automatic sup­port levelling are provided as standard.
Optionally at the BTT the support
forces can be displayed.

Touch displays

Below the joysticks, inte­grated in the armrests, touch
displays are installed by
which the various operation
functions can be selected.
Beside others these are the
supporting of the crane and
the adjustment of the working
flood light as well as the heat­ing and climate regulation.

PN 199.00.E07. 2014 The illu strations contain al so accessor ies and s pecial equip ment wh ich are n ot inclu ded in th e stand ard sco pe of delivery. Subject to a lteration.

Liebherr-Werk Ehingen GmbH

Postfach 1361, 89582 Ehingen, Germany
 [phone], Fax [phone]
www.liebherr.com, E-Mail: [e-mail]
www.facebook.com/LiebherrConstruction