LG URNTC2306N, URNTS3106N User Manual

OWNER’S MANUAL

REFRIGERATOR

Please read this owner's manual thoroughly before operating and keep it handy for reference at all times.

URNTS3106N

URNTC2306N

www.LGSIGNATURE.com

MFL71439502_Rev.02

Copyright © 2020 LG Electronics Inc. All Rights Reserved.

ENGLISH

2 TABLE OF CONTENTS

TABLE OF CONTENTS

3PRODUCT FEATURES

4IMPORTANT SAFETY INSTRUCTIONS

7 COMPONENTS

7Refrigerator Exterior

8Refrigerator Interior

9INSTALLATION

9Installation Overview

10Specifications

11Unpacking the Refrigerator

11Choosing the Proper Location

11- Flooring

11- Ambient Temperature

12- Dimensions and Clearances

13Removing/Assembling the Doors

17Connecting the Water Line

17- Before You Begin

18- Water Pressure

18- What You Will Need

19- Water Line Installation Instructions

20Turning On the Power

21Leveling

21Door Mullion and Auto Open Door

21Door Alignment

21- Adjusting Door Height

30 Storing Food

30- Food Preservation Location

31- Food Storage Tips

31- Storing Frozen Food

32Adjusting the Refrigerator Shelves

32- Detaching the Shelf

32- Assembling the Shelf

33- When Closing the Door

33 CustomChill™ Pantry

33- Setting the CustomChill™ Pantry

34Crisper Drawers

34- Removing the Crisper Drawers

34- Assembling the Crisper Drawers

35- Removing the Crisper Support Box

35- Assembling the Crisper Support Box

36Removing the CustomChill™ Pantry Insert

36Hidden Bar Tray

36InstaView™Door-in-Door®

37EasyLift Bin

37 Freezer Drawer

37- Removing the Freezer Drawer

38- Assembling the Freezer Drawer

38- Removing the Drawer Support

39- Assembling the Drawer Support

39Refrigerator/Freezer Door Bins

41 SMART FUNCTIONS

41 LG ThinQ Application

45Smart Grid Function

46Using the Voice Assistant

48Smart Diagnosis™ Feature

	22	HOW TO USE	49		MAINTENANCE
			49		Cleaning
	22	Before Use
			50		Replacing the Fresh Air Filter
	23	Wi-Fi Eclipse Display
			51		Replacing the Water Filter
	23	- Wi-Fi Eclipse Display Features
	25	- Using the Wi-Fi Eclipse Display	55
	26	Sabbath Mode			TROUBLESHOOTING
	26	In-Door Ice Bin
	26	- Detaching the In-Door Ice Bin
	27	- Assembling the In-Door Ice Bin	66		LIMITED WARRANTY
	27	Automatic Icemaker
	29	Ice and Water Dispenser

PRODUCT FEATURES 3

PRODUCT FEATURES

Depending on the model, some of the following functions may not be available.

DOOR ALARM

The Door Alarm function is designed to prevent refrigerator malfunctioning that could occur if a refrigerator door or freezer door remains open. If a refrigerator door or freezer door is left open for more than 60 seconds, a warning alarm sounds at 30 second intervals until it is closed.

AUTO CLOSING HINGE

The refrigerator doors close automatically with a slight push. (The door only closes automatically when it is open at an angle less than 30°.)

ICE PLUS

Ice production can be increased by approximately 20 percent when the freezer section is maintained at the coldest temperature for a 24-hour period.

MEASURED FILL DISPENSER

Select from the Measured Fill menu on the dispenser to quickly dispense pre-measured amounts automatically.

InstaView™Door-in-Door®

Two quick knocks on the sleek, mirrored glass panel allow you to see inside the easy access compartment without opening the door. This reduces cold air loss, and helps keep food fresh longer.

AUTO OPEN DOOR

This smart sensor is located at the foot of the refrigerator and opens the door automatically. When you stand in front of the refrigerator, lighted "Door Open" text is projected onto the floor. Step on the text and the door gently opens.

FOLD-DOWN BIN RAILS

ENGLISH

Use the metal bars on the Door-in-Door bins as either bin dividers or as rails to keep tall items secure.

ENGLISH

4 IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

This guide contains many important safety messages. Always read and obey all safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard signal word WARNING or CAUTION. These words mean:

WARNING You can be killed or seriously injured if you do not follow instructions.

CAUTION Indicates an imminently hazardous situation which, if not avoided, may result in minor or moderate injury, or product damage.

WARNING

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety precautions should be followed, including the following:

Power

•• NEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and pull it straight out from the outlet.

•• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

•• Do not use an uncertified power outlet.

•• Unplug the power plug immediately in the event of a blackout or thunderstorm.

•• Plug in the power plug with the power cord facing downward.

Installation

•• Contact an authorized service center before you install or relocate the refrigerator.

•• When moving your refrigerator away from the wall, be careful not to roll over or damage the power cord.

•• Prior to use, ensure that you are connecting this product to a dedicated, grounded electrical outlet rated for use with this product (115V, 60Hz, AC only). It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.

•• Do not install the refrigerator where there may be a danger of the unit falling.

Use

•• DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

•• Do not hang on to or place heavy objects on the refrigerator’s dispenser.

•• Do not place heavy or dangerous objects (bottles with liquid) on the refrigerator.

•• Do not put live animals inside the refrigerator.

•• Do not allow children to climb into the product when it is in use.

•• In the event of a gas leak (propane/LPG), ensure adequate ventilation and contact an authorized service center before resuming use. Do not touch or disassemble the electric outlet of the refrigerator.

•• In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure adequate ventilation and contact an authorized service center.

•• Do not use or place flammable substances (chemicals, medicine, cosmetics, etc) near the refrigerator or store them inside the refrigerator. Do not place the refrigerator in the vicinity of flammable gas.

•• Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or personal injury if items are removed with excessive force.

IMPORTANT SAFETY INSTRUCTIONS 5

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety precautions should be followed, including the following:

•• Do not hit the glass door panel with excessive force. Do not allow hard objects like cookware or glass bottles to hit the glass door panel. The glass could break, resulting in a risk of personal injury or product damage.

•• This product is not to be used for special purposes such as the storage of medicine or test materials or for use on ships, etc.

•• Unplug the power plug before cleaning or repairing the refrigerator.

•• When you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power.

•• Do not modify or extend the power cord.

•• Do not use a dryer to dry the interior. Do not light a candle to remove interior odors.

•• For your safety, this appliance must be properly grounded. Have the wall outlet and the circuit checked by a qualified electrician to make sure the outlet is properly grounded.

•• Do not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.

•• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

•• Do not use an adapter plug and plug the power plug into a multi-outlet extension cord.

•• Disconnect the power cord immediately if you hear a noise, smell a strange odor or detect smoke coming from the appliance.

•• Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

•• Do not disassemble or modify the refrigerator.

•• Do not put hands, feet, or metal objects below or behind the refrigerator.

•• Do not operate the refrigerator or touch the power cord with wet hands.

•• In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism or with the heating element that releases the cubes. Do not place fingers or hands on the automatic ice-making mechanism while the refrigerator is plugged in.

•• When dispensing ice from the dispenser, do not use crystal ceramics.

•• Do not touch the cold surfaces in the freezer compartment with wet or damp hands, when your refrigerator is in operation.

•• Do not put glass containers, glass bottles or soda in the freezer.

•• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

•• Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health issue.

•• If you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in accordance with the relevant environmental law.

•• Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When disposing of the refrigerator, remove the packing materials from the door or take off the doors but leave the shelves in place so that children may not easily climb inside.

•• If connected to a circuit protected by fuses, use time delay fuse.

ENGLISH

ENGLISH

6 IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety precautions should be followed, including the following:

CAUTION

Installation

•• The refrigerator must be properly installed in accordance with the Installer Instructions that were taped to the front of the refrigerator.

•• Be careful when you unpack and install the refrigerator. Immediately dispose of plastic and other packing materials out of reach of children.

•• The appliance must be positioned for easy access to a power source.

Use

•• Close the door carefully when children are around.

•• Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small. Be careful closing doors when children are nearby.

•• If you store food improperly, be aware that it may fall and cause injury.

•• Do not use aerosols near the refrigerator.

•• Do not store articles on the top of the appliance.

Maintenance

•• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.

•• Wipe foreign objects (such as dust and water) off the prongs of the power plug and contact areas regularly.

•• Do not store, disassemble or repair the refrigerator by yourself.

•• Remove any dust or foreign matter from the power plug pins.

•• Do not use a wet or damp cloth when cleaning the plug.

•• If the refrigerator is disconnected from the power supply, you should wait for at least five minutes before plugging it back in.

•• If you notice a chemical or burning plastic smell or see smoke, unplug the refrigerator immediately and contact your LG Electronics Service Center.

SAVE THESE INSTRUCTIONS

COMPONENTS 7

COMPONENTS

Use this page to become more familiar with the parts and features of your refrigerator.

*The appearance and specifications of the actual product may differ depending on the model.

Refrigerator Exterior

Dispenser Control Panel

Displays the icemaker and dispenser modes and the water filter status.

Filtered Water and

Ice Dispenser

Dispenses purified water and ice.

Voice Assistant Device

A voice assistant device is built into the door.

InstaView™ Door-in-Door®

Wi-Fi Eclipse Display

Intuitively displays status and enables control of fridge/ freezer temperatures, energy consumption monitoring, smart saving, and smart grid features.

Refrigerator

Preserves food.

Freezer

Preserves frozen food.

ENGLISH

ENGLISH

8 COMPONENTS

Refrigerator Interior

				Adjustable Refrigerator Shelf
				The shelves in your refrigerator are adjustable
LED Interior Lamp				to meet your individual storage needs.

The interior lamps light up

the inside of the refrigerator. InstaView™ Door-in-Door®

	Refrigerator	See what's inside the
	Bin	Door-in-Door compartment
		without opening the door.
		Keeps the cold air inside
		and saves energy.
	Indoor Ice Bin	Condiment Bin
	Ice cubes are
	automatically	Crisper
	produced.
	Crisper	CustomChill™
		Pantry

	Hidden Bar Tray
Freezer Bin	Freezer Bin
Freezer	Freezer
Drawer	Drawer

INSTALLATION 9

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

ENGLISH

1 Unpacking your	2 Choosing the proper	3 Disassembling/Assembling
refrigerator	location

4 Connecting the	5 Leveling and Door
water supply and	Alignment
water line

1/8”±1/16” mm

•• It may be necessary to increase the refrigerator's tilt after the door bins are filled to compensate for the increased weight of the doors.

•• Check if the gap between Holder and Pillar is 1/8±1/16” (4±2 mm). As in the figure, pull forward and backward with hand with speedy feeling, and check if Pillar is normally folded and spread.

NOTE

Connect to potable water supply only.

ENGLISH

10 INSTALLATION

Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Bottom-freezer refrigerator model URNTS3106N

Description	French-door refrigerator
Electrical requirements	115 VAC @ 60 Hz
Min./Max. Water pressure	20 - 120psi (138 - 827kPa)
Dimensions	35 7/8”(W) x 36 1/2”(D) x 70 1/4”(H) x 51 1/8”(D w/ door open)
	912(W) X 929(D) X 1784(H) X 1298 mm (D w/ door open)
Net weight	483 lb. (219 kg)
Bottom-freezer refrigerator model URNTC2306N
Description	French-door refrigerator
Electrical requirements	115 VAC @ 60 Hz
Min./Max. Water pressure	20 - 120psi (138 - 827kPa)
Dimensions	35 7/8”(W) x 29 5/8”(D) x 70 1/4”(H) x 44 3/16”(D w/ door open)
	912(W) X 754(D) X 1784(H) X 1123 mm (D w/ door open)
Net weight	430 lb. (195 kg)

INSTALLATION 11

Unpacking the Refrigerator

WARNING

••Use two or more people to move and install the refrigerator. Failure to do so can result in back or other injury.

••Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur.

••Keep flammable materials and vapors, such as gasoline, away from the refrigerator. Failure to do so can result in fire, explosion, or death.

Remove tape and any temporary labels from your refrigerator before using. Do not remove any warning-type labels, the model and serial number label, or the Tech Sheet that is located under the front of the refrigerator.

But, when you remove tape and temporary label, remove them after pulling out the power plug.

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

Refrigerator shelves are installed in the shipping position. Please reinstall shelves according to your individual storage needs.

Choosing the Proper Location

•• Select a place where a water supply can be easily connected for the automatic icemaker.

NOTE

The water pressure must be 20~120 psi or 138~827 kPa or 1.4~8.4 kgf/cm² on models without a water filter and 40~120 psi or 276~827 kPa or 2.8~8.4 kgf/cm² on models with a water filter.

•• The refrigerator should always be plugged into its own individual properly grounded electrical outlet rated for 115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes. This provides the best performance

and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. It is recommended that a separate circuit serving only this appliance be provided.

WARNING

To reduce the risk of electric shock, do not install the refrigerator in a wet or damp area.

Flooring

To avoid noise and vibration, the unit must be leveled and installed on a solidly constructed floor. If required, adjust the leveling legs to compensate for unevenness of the floor. The front should be slightly higher than the rear to aid in door closing. Leveling legs can be turned easily by tipping the cabinet slightly. Turn the leveling legs to the left to raise the unit or to the right to lower it. (See Leveling and Door AlIgnment.)

NOTE

Installing on carpeting, soft tile surfaces, a platform or weakly supported structure is not recommended.

Ambient Temperature

Install this appliance in an area where the temperature is between 55°F (13°C) and 110°F (43°C). If the temperature around the appliance is too low or high, cooling ability may be adversely affected.

ENGLISH

ENGLISH

12 INSTALLATION

Dimensions and Clearances

•• Check the dimensions of the appliance and the installation path to ensure there is sufficient room to move the refrigerator through doors or narrow openings.

•• If an opening is too narrow to fit the refrigerator through, the doors must be removed.

•• The installation location chosen for the refrigerator should allow space behind the unit for connections and airflow and space in front to open the doors and drawers.

•• Too small of a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges. Allow at least 24 inches (610 mm) in front of the refrigerator to open the doors, and at least 2 inches (50.8 mm) between the back of the refrigerator and the wall.

	B
	A		E
C	D	F	M
			G

-

List

URNTS3106N

URNTC2306N

A

Depth without handle

36

1/2” (929 mm)

29

5/8”

(754 mm)

B

Width

35

7/8” (912 mm)

35

7/8”

(912 mm)

C

Height to Top of Case

68 7/8” (1751 mm)

68 7/8” (1751 mm)

D

Height to Top of Hinge

70 1/4“ (1784 mm)

70 1/4“ (1784 mm)

E

Back Clearance

2” (50 mm)

2”

(50 mm)

F

Depth without Door

31

7/8” (811 mm)

25”

(636 mm)

G

Depth (Total with Door Open 90°)

51 1/8” (1298 mm)

44 3/16”

(1123 mm)

K

Front Clearance

24” (610 mm)

24”

(610 mm)

M

Depth with Handle

36

1/2” (929 mm)

29

5/8”

(754 mm)

	INSTALLATION 13
Removing/Assembling the Doors	3 Remove the cover and pull out the tube .
	Disconnect all wire harnesses .

Removing the Left Refrigerator Door

1The water supply is connected to the upper right part of the rear surface of the refrigerator. Remove the ring in the joint area. Hold the water supply connection and gently push the collet to detach the water supply line as shown in .

1

Collet

NOTE

Detachment of the water supply line is applicable only when detaching the left refrigerator door.

4Rotate the hinge lever counterclockwise

. Lift the top hinge free of the hinge lever latch.

Hinge Lever Latch
1	2

CAUTION

	When lifting the hinge free of the latch, be
2 Remove the screws from the hinge cover	careful that the door does not fall forward.
at the top of the refrigerator. Lift the
hook(not visible), located on the side of the
cover at the bottom edge, with a flat-head	5 Lift the door from the middle hinge pin and
screwdriver.	remove the door.

CAUTION

ENGLISH

Place the door, inside facing up, on a non-scratching surface.

ENGLISH

14	INSTALLATION
Removing the Right Refrigerator		4 Lift the door from the middle hinge pin and
Door		remove the door.
1	Remove the screws from the hinge cover

at the top of the refrigerator. Lift the hook(not visible), located on the side of the cover at the bottom edge, with a flat-head screwdriver.

CAUTION

Place the door, inside facing up, on a non-scratching surface.

2 Detach the wire harness .

Removing the Freezer Doors

1 Remove the two hinge bolts.

1

1

3 Rotate the hinge lever	clockwise.
Lift the top hinge free of the hinge
lever latch.		2 Twist the hinge to raise the pivoting end
		so that the door can be lifted off. Lift the
		door off the lower hinge pin and remove it.
	Hinge Lever Latch
2	1
CAUTION		3 Unscrew the screw that attaches the
When lifting the hinge free of the hinge		lower hinge cover and remove the cover.
lever latch, be careful that the door
does not fall forward.

2

1

	INSTALLATION 15
4 Disconnect all wire harnesses.	3 Position the bottom hinge cover in its place
	and tighten the cover screw .

5Remove the door by lifting it off the lower hinge pin.

Lower hinge

Assembling the Freezer Doors

1 Lower the door onto the lower hinge pin.

1

2

4Position the middle hinge pin in place to hold the door and insert the two hinge bolts.

5 Tighten the two hinge bolts.

ENGLISH

2 Connect the wire harnesses.

ENGLISH

16 INSTALLATION

Assembling the Right Refrigerator Door

Install the right refrigerator door first.

1Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin as shown in the figure.

Assembling the Left Refrigerator

Door

Install the left refrigerator door after the right door is installed.

1Make sure that the plastic sleeve is inserted in the bottom of the door. Install the refrigerator door onto the middle hinge pin.

	2 Fit the hinge over the hinge lever latch
	and slot it into place. Rotate the lever	2 Fit the hinge	over the hinge lever latch
	counterclockwise to secure the hinge.
		and slot it into place. Rotate the lever
		clockwise	and fasten the hinge.

Hinge Lever Latch

1

2

3 Connect the wire harness .

3

1	1

4 Position the cover in its place. Insert and
tighten the cover screws.	4

Hinge Lever Latch 1

2

Connect all the wire harnesses.

Push the water supply tube into the hole

on the top case and pull it through the backplate.

		INSTALLATION 17
5	Hold the water supply connection and	Connecting the Water Line
	gently push in the collet to connect the
	water supply line as shown in . Insert	Before You Begin
	the tube at least 5/8 inch (15 mm) into the
	connector.	This water line installation is not covered by the
		refrigerator warranty. Follow these instructions
		carefully to minimize the risk of expensive water
		damage.
		Water hammer (water banging in the pipes) in
	Collet	house plumbing can cause damage to refrigerator
		parts and can lead to water leakage or flooding.
		Call a qualified plumber to correct water hammer
		before installing the water supply line to the
		refrigerator.
		CAUTION
6	Position the cover in its place. Insert and	To prevent burns and product damage,
	tighten the cover screws.	only connect the refrigerator water line to
		a cold water supply.

	If you use your refrigerator before connecting
	the water line, make sure the icemaker power
	switch on the control panel is in the OFF
NOTE	position.

	Collet	CAUTION
	Tube
		Do not install the icemaker tubing in
	Insert Line	areas where temperatures fall below
		freezing.

1)Gently insert the tube until only one line shows on the tube.

ENGLISH

(Correct)

(Incorrect)

2)Pull the tube to make sure that the tube is tightly fastened.

ENGLISH

18 INSTALLATION

Water Pressure

The water pressure must be 20~120 psi or 138~827 kPa or 1.4~8.4 kgf/cm² on models without a water filter and 40~120 psi or 276~827 kPa or 2.8~8.4 kgf/cm² on models with a water filter.

If a reverse osmosis water filtration system is connected to the cold water supply, this water line installation is not covered by the refrigerator warranty. Follow the instructions carefully to minimize the risk of expensive water damage.

If a reverse osmosis water filtration system is connected to the cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276~414 kPa or 2.8~4.2 kgf/cm², less than 2.0~3.0 sec. to fill a cup of 7 oz or 198 cc capacity).

CAUTION

Wear eye protection during installation to prevent injury.

If the water pressure from the reverse osmosis system is less than 20 psi or 138 kPa or 1.4 kgf/ cm² (takes more than 4.0 sec to fill a cup of 7 oz or 198 cc capacity):

•• Check to see if the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

•• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

•• If the issue concerning water pressure from reverse osmosis remains, call a licensed, qualified plumber.

•• All installations must be in accordance with local plumbing code requirements.

What You Will Need

•• Copper Tubing, ¼ in. outer diameter, to connect the refrigerator to the water supply. Be sure both ends of the tubing are cut square.

•• To determine how much tubing you need: measure the distance

from the water valve on the back of the refrigerator to the water supply pipe. Then, add 8 feet (2.4 m). Be sure there is sufficient extra tubing (about 8 feet [2.4 m] coiled into 3 turns of about 10 in. [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.

•• Power drill.

•• ½ in. or adjustable

wrench.

•• Flat blade and Phillips

head screwdrivers.

•• Two ¼ in. outer diameter compression

nuts and 2 ferrules (sleeves) to connect the copper tubing to the shutoff valve and the refrigerator water valve.

•• If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you

can cut off the flared fitting with a tube cutter and then use a compression fitting.

•• Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 in. at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water

supply kits. Before purchasing, make

sure a saddle-type valve complies with

your local plumbing codes.

NOTE

A self piercing saddle type water valve should not be used.

	INSTALLATION 19
Water Line Installation Instructions	4 FASTEN THE SHUTOFF VALVE
WARNING	Fasten the shutoff valve to the cold water
	pipe with the pipe clamp.

	When using any electrical device		Pipe Clamp
	(such as a power drill) during
	installation, be sure the device is
	battery powered, double insulated
	or grounded in a manner that will
	prevent the hazard of electric shock.		Saddle-Type	Vertical Cold
			Shutoff Valve	Water Pipe
Install the shutoff valve on the nearest			NOTE
frequently used drinking water line.
1	SHUT OFF THE MAIN WATER SUPPLY		Commonwealth of Massachusetts
			Plumbing Codes 248CMR shall be adhered
	Turn on the nearest faucet to relieve the		to. Saddle valves are illegal and their use is
	pressure on the line.		not permitted in Massachusetts. Consult
2	CHOOSE THE VALVE LOCATION		with your licensed plumber.
	Choose a location for
	the valve that is easily	5	TIGHTEN THE PIPE CLAMP
	accessible. It is best to
	connect into the side of a		Tighten the clamp screws until the sealing
	vertical water pipe. When		washer begins to swell.
	it is necessary to connect
	into a horizontal water		NOTE: Do not overtighten the clamp or
	pipe, make the connection to the top or
			you may crush the tubing.
	side, rather than at the bottom, to avoid
	drawing off any sediment from the water			Washer
	pipe.
				Inlet End
3			Pipe Clamp
	DRILL THE HOLE FOR THE VALVE		Clamp Screw
	Drill a ¼ in. hole in
	the water pipe using
	a sharp bit. Remove
	any burrs resulting
	from drilling the hole
	in the pipe. Be careful
	not to allow water	6	ROUTE THE TUBING
	to drain into the drill. Failure to drill a ¼ in.
	hole may result in reduced ice production		Route the tubing between the cold water
	or smaller cubes.		line and the refrigerator.
			Route the tubing through a hole drilled in
	NOTE		the wall or floor (behind the refrigerator or
			adjacent base cabinet) as close to the wall
	The hookup line cannot be white, plastic		as possible.
	tubing. Licensed plumbers must use
	only copper tubing (NDA tubing #49595		NOTE
	or #49599) or Cross Link Polyethylene

(PEX) tubing.	Be sure there is sufficient extra tubing
	(about 8 feet coiled into 3 turns of
	about 10 in. diameter) to allow the
	refrigerator to move out from the wall
	after installation.

ENGLISH

ENGLISH

20 INSTALLATION

7CONNECT THE TUBING TO THE VALVE Place the compression nut and ferrule (sleeve) for the copper tubing onto the end of the tubing and connect it to the shutoff valve. Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

Saddle-Type	Compression
Shutoff Valve	Nut

Packing Nut

Outlet ValveFerrule (sleeve)

8 FLUSH OUT THE TUBING

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water off at the water valve after about one quart of water has

been flushed through the tubing.

9CONNECT THE TUBING TO THE REFRIGERATOR

NOTE: Before making the connection to the refrigerator, be sure that the

refrigerator power cord is not plugged into the wall outlet.

10 TURN THE WATER ON AT THE SHUTOFF

VALVE

Tighten any connections that leak.

CAUTION

Check to see if leaks occur at the water line connections.

11 PLUG IN THE REFRIGERATOR

Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall.

12 START THE ICEMAKER

Turn the icemaker ON at the control panel.

The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically if the icemaker has been turned ON.

a.Remove the plastic flexible cap from the water valve.

b.Place the compression nut and ferrule (sleeve) onto the end of the tubing as shown.

c.Insert the end of the copper tubing into the connection as far as possible. While holding the tubing, tighten the fitting.

Tubing Clamp

¼ in. Tubing

¼ in. Compression Nut

Ferrule (sleeve)

Refrigerator

Connection

Turning On The Power

Plug in the refrigerator.

CAUTION

••Connect to a rated power outlet.

••Have a certified electrician check the wall outlet and wiring for proper grounding.

••Do not damage or cut off the ground terminal of the power plug.

		INSTALLATION 21
NOTE	1	Make sure both front leveling legs are
The front leveling legs must be extended		extended fully and in firm contact with the
		floor.
fully so they are in firm contact with the
floor (even if leveling or door alignment	2	Follow the instructions in the Door
is not needed).		Alignment section to raise the left
Leveling		refrigerator door until the door mullion is
		once again working properly.
After installing, plug the refrigerator’s power	3	Adjust the right refrigerator door so it
cord into a 3-prong grounded outlet and push		aligns with the left refrigerator door.

the refrigerator into the final position.

The refrigerator has two front leveling legs— one on the right and one on the left. Adjust the legs to alter the tilt from front-to-back or side- to-side. If the refrigerator seems unsteady, or you want the doors to close more easily, adjust the refrigerator’s tilt using the instructions below:

1Turn the leveling leg to the left to raise

that side of the refrigerator or to the right to lower it. It may take several turns of the leveling leg to adjust the tilt of the refrigerator.

NOTE

A flare nut wrench works best, but an open-end wrench will suffice.

Do not over-tighten.

2Open both doors again and check to make sure that they close easily. If the doors do not close easily, tilt the refrigerator slightly more to the rear by turning both leveling legs to the left. It may take several more turns, and you should turn both leveling legs the same amount.

Door Mullion and Auto Open

Door

Once the door bins are filled, the doors may become misaligned, preventing the door mullion or the Auto Open Door function from working properly.

If the mullion on the left refrigerator door does not open and close properly or the right door stays ajar after the Auto Open Door function, follow the directions below.

Door Alignment

If the floor is not flat, the door heights may differ. In this case, use the following method to adjust the difference.

Adjusting Door Height

Adjusting Fridge Door	Open the fridge door
Height	and use a wrench to
Height difference	rotate the door hinge
	bolt as shown.
	Fridge door
	Freezer door
Adjusting Freezer	Open the freezer door
Door Height	and use a wrench to
	rotate the door hinge
	bolt as shown.
	Freezer door

Height difference

ENGLISH

ENGLISH

22 HOW TO USE

HOW TO USE

Before use

Clean the refrigerator.

Clean the refrigerator thoroughly and wipe off all dust that accumulated during shipping.

CAUTION

•• Do not scratch the refrigerator with a sharp object or use a detergent that contains alcohol, a flammable liquid or an abrasive when removing any tape or adhesive from the refrigerator,.

•• Do not peel off the model or serial number label or the technical information on the rear surface of the refrigerator.

NOTE

Remove adhesive residue by wiping it off with your thumb or dish detergent.

Open refrigerator and freezer doors to ventilate the interior.

The inside of the refrigerator may smell like plastic at first. Remove any adhesive tape from inside the refrigerator and open the refrigerator and the freezer doors for ventilation.

Connect the power supply.

Check if the power supply is connected before use.

Read the “Turning On The Power” section.

Turn off the icemaker if the refrigerator is not yet connected to the water supply.

Turn off the automatic icemaker and then plug the power plug of the refrigerator into the grounded electrical outlet.

* This is applicable only to certain models.

CAUTION

Running the automatic icemaker before connecting it to the water supply may cause the refrigerator to malfunction.

Wait for the refrigerator to cool.

Allow your refrigerator to run for at least two to three hours before putting food in it. Check the flow of cold air in the freezer compartment to ensure proper cooling.

CAUTION

Putting food in the refrigerator before it has cooled could cause the food to spoil, or a bad odor could linger inside the refrigerator.

The refrigerator makes a loud noise after initial operation.

This is normal. The volume will decrease as the temperature lowers.

HOW TO USE 23

Wi-Fi Eclipse Display

Depending on the model, some of the following functions may not be available.

Wi-Fi Eclipse Display Features

		9
1	3	5	7
2	4	6	8

ENGLISH

1 Smart Grid / Wi-Fi

Smart Grid

Press the Smart Grid button to turn the Smart Grid function On/Off. When the function is on, the icon illuminates. The Smart Grid function automatically turns on when the refrigerator is connected to the Wi-Fi network. When the

refrigerator is responding to a Demand Response (DR) message from the electric company, the Grid text illuminates.

Wi-Fi

The Wi-Fi button, when used with the LG Smart Refrigerator smart phone app, allows the refrigerator to connect to a home Wi-Fi network. Refer to Smart Function for information on the initial setup of the application.

The Wi-Fi icon shows the status of the refrigerator's network connection. The icon illuminates when the refrigerator is connected to the Wi-Fi network.

Press and hold the Wi-Fi button for 3 seconds to connect to the network. The icon blinks while the connection is being made, then turns on once the connection is successfully made.

2 Lock

The Lock function disables every other button on the display.

•• When power is initially connected to the refrigerator, the Lock function is off.

•• To activate the Lock function, press and hold the Lock button until the lock indicator appears in the display. The other buttons are now disabled.

•• To disable the Lock function, press and hold the Lock button for approximately three seconds.

3 Auto Open Door

The right refrigerator door opens automatically if you place a foot near the motion sensor at the bottom of the door. This is convenient when you have both hands full of groceries and need to open the refrigerator door. To set the Auto Open Door function, press the button repeatedly to toggle between the ON, Sound Off, and OFF settings.

Using the Auto Open Door Function

1.When the Auto Open Door Function is enabled, text is displayed on the floor near the motion sensor.