KROHNE OPTIFLEXHart User Manual
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
User Guide
Optiflex (TDR)
Device
Asset Management
Solutions (AMS)
HART Communicator 375
Version 1.1
January 2008
© 2006 KROHNE SAS 26103 Romans (France)
Page 1 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
Table of Contents
1 HART® Transmitter Revisions and Instrument Firmware ............................................................................................................ 3
1.1 Device Revision ...................................................................................................................................................................... 3
1.2 DD Revision ........................................................................................................................................................................... 3
2 Installation of DDL in AMS .......................................................................................................................................................... 3
3 Menu .............................................................................................................................................................................................. 3
3.1 Access Rights .......................................................................................................................................................................... 3
3.1.1 Password protection implementation .................................................................................................................................. 3
3.1.2 Supervisor Password ........................................................................................................................................................... 4
3.1.3 Service Password ................................................................................................................................................................ 6
3.2 Save Device Parameters .......................................................................................................................................................... 6
3.3 Diagnostic and Test ................................................................................................................................................................. 7
3.3.1 Internal Test ........................................................................................................................................................................ 7
3.3.2 Set Output1 ......................................................................................................................................................................... 8
3.3.3 Set Output2 ......................................................................................................................................................................... 9
3.4 Calibration ............................................................................................................................................................................... 9
3.4.1 Output1 Lower .................................................................................................................................................................... 9
3.4.2 Output1 Upper .................................................................................................................................................................. 10
3.5 Tables .................................................................................................................................................................................... 12
3.5.1 Volume/Mass Table .......................................................................................................................................................... 12
3.5.2 Linearisation Table ........................................................................................................................................................... 15
3.5.3 Delete Tables .................................................................................................................................................................... 16
3.6 Reset ...................................................................................................................................................................................... 17
3.6.1 Factory Reset .................................................................................................................................................................... 17
3.6.2 Customer Reset ................................................................................................................................................................. 18
3.6.3 Device Reset ..................................................................................................................................................................... 18
3.7 Threshold Calculation ............................................................................................................................................................ 20
3.7.1 Level Threshold ................................................................................................................................................................ 20
3.8 Application Setup .................................................................................................................................................................. 21
3.9 Calculated Er Value .............................................................................................................................................................. 24
3.10 Snapshot .............................................................................................................................................................................. 24
3.11 Auto Probe Length Calculation ........................................................................................................................................... 27
3.12 Device Configuration ............................................................................................................................................................ 29
3.12.1 Installation Parameters1 .................................................................................................................................................... 29
3.12.2 Installation Parameters2 .................................................................................................................................................... 30
3.12.3 Output Selection ............................................................................................................................................................... 31
3.12.4 Primary Output Setting ..................................................................................................................................................... 32
3.12.5 Secondary Output Setting ................................................................................................................................................. 33
3.12.6 Quick Setup Summary ...................................................................................................................................................... 34
3.12.7 Service Parameters 1 ......................................................................................................................................................... 35
3.12.8 Service Parameters 2 ........................................................................................................................................................ 35
3.12.9 HART ............................................................................................................................................................................... 36
3.12.10 Device .......................................................................................................................................................................... 38
3.13 Process Variable .................................................................................................................................................................... 39
3.14 Device Diagnostic .................................................................................................................................................................. 40
4 Status Meaning............................................................................................................................................................................. 41
5 HART® Communicator 375 (HC375) ......................................................................................................................................... 42
5.1 Offline Restriction ................................................................................................................................................................. 42
5.2 Save Device Parameters ........................................................................................................................................................ 42
© 2006 KROHNE SAS 26103 Romans (France)
Page 2 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
1 HART® Transmitter Revisions and Instrument Firmware
1.1 Device Revision
The Optiflex HART® transmitter has only one revision: Device revision 1.
1.2 DD Revision
Optiflex 1300C has the DD revision 2.
DD is tested with AMS 9.0 but can be used with AMS version 6.1 up to 9.0.
2 Installation of DDL in AMS
Refer to the AMS help to install the “Optiflex 1300” DD into an AMS System.
3 Menu
3.1 Access Rights
3.1.1 Password protection implementation
There will be two user login, Supervisor & Service which is implemented in <Access Rights>
menu. By default, Supervisor can see & edit all parameters except service parameter. After service
person is logged in he can see & edit all the parameters including the service parameters and
tables.
Password can be numeric digits from 0-9. There may be maximum six digits password. As we
can’t store the password directly in AMS, we are validating the password in AMS by reading the
password from device. Password setting facility is not given from AMS to avoid conflicts to know
the password to login from HMI. After validation it will give following messages “Supervisor
Password OK” or “Service Password OK” as per the login.
On clicking the Access Rights on the main menu, two submenus appear as Supervisor and Service.
© 2006 KROHNE SAS 26103 Romans (France)
Page 3 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
3.1.2 Supervisor Password
On clicking Supervisor it shows the following screen.
Note: Before accessing this menu user needs to select the “configuration variables” for
synchronization of all device parameters and for proper validation of the device parameters.
On clicking next, it shows the following window, which asks user to enter the Supervisor
Password with the default value as 65535.
© 2006 KROHNE SAS 26103 Romans (France)
Page 4 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
After entering the valid password and clicking next, it shows the following screen:
For success: “Supervisor Password OK”
For invalid password: “Supervisor Password Invalid”
© 2006 KROHNE SAS 26103 Romans (France)
Page 5 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
3.1.3 Service Password
See “Supervisor Password” method.
3.2 Save Device Parameters
ATTENTION: This is a very important method.
Each time the device configuration is modified
method. Otherwise the modifications will not be taking into account.
(after applying changes) it is necessary to execute this
© 2006 KROHNE SAS 26103 Romans (France)
Page 6 of 42
3.3 Diagnostic and Test
3.3.1 Internal Test
On selecting “Internal Test” from the main menu, device performs self test and displays results as
following:
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
© 2006 KROHNE SAS 26103 Romans (France)
Page 7 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
3.3.2 Set Output1
It allows fixing different values to the current output1 . It is a test mode. User can check the loop
currents in output1 and output2. The list of currents are displayed in the list box.
Once the appropriate current is selected the loop current is fixed to that current value. Check the loop
current by ammeter and validates the current as selected from the device. The loop current exits from
the current mode after clicking on 'Exit' or 'Cancel' from the method.
© 2006 KROHNE SAS 26103 Romans (France)
Page 8 of 42
3.3.3 Set Output2
See “Set Output1”
3.4 Calibration
The Calibration can be done for the output1 and output2. Here the following sections will describe
the detailed about the calibration screen options for the output1 lower and upper.
3.4.1 Output1 Lower
In Output1 Lower, it allows user to trim current output1.
The user starts to fix the current to 4mA, after entering the current value he reads on a voltmeter,
this value is sent to the device. This method allows adjusting to have exactly the good current
value of output1 loop.
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
© 2006 KROHNE SAS 26103 Romans (France)
Page 9 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
3.4.2 Output1 Upper
In Output1 Upper, user allows to trim current output1.
The user start to fix the current to 20mA, after entering the current value he read on a voltmeter,
this value is sent to the device. This method allows adjusting to have exactly the good current
value of output1 loop.
© 2006 KROHNE SAS 26103 Romans (France)
Page 10 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
© 2006 KROHNE SAS 26103 Romans (France)
Page 11 of 42
3.5 Tables
3.5.1 Volume/Mass Table
Double Click on “Volume/Mass Table” will display all the entries of conversion table in ‘2 x 2’
format.
Display will be in following steps:
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
1. After Displaying all entries:
If yes is selected, it permits user to edit or add new entries.
© 2006 KROHNE SAS 26103 Romans (France)
Page 12 of 42
User Guide for Optiflex (TDR) DD of AMS
Dev Rev-01, DD Rev-02
2. Selection of Next Entry will show next entry Level to edit, after clicking Next, Volume/Mass is
displayed for next Entry to edit. After editing Level & Volume/Mass for current entry, above shown
menu is displayed again.
3. Selection of Previous Entry will show previous entry Level to edit, after clicking next, Volume/Mass
is displayed for previous Entry to edit. After editing Level & Volume/Mass for current entry, above
shown menu is displayed again.
© 2006 KROHNE SAS 26103 Romans (France)
Page 13 of 42
Loading...