Page 1
Warning
Caution
Warning
Caution
Caution
Caution
Caution
Caution
(1)
(2)
AB
Camera
Controller
96M12152
Installation
Do not use the CA-CNX10U/CHX10U in the following locations:
Repeater for camera cable extension
(for normal camera/high-speed camera)
CA-CNX10U/CA-CHX10U
Instruction Manual
• Locations where the CA-CNX10U/CHX10U is exposed to
direct sunlight.
• Locations where the ambient temperature exceeds or drops
below the specification range, or where the temperature
changes rapidly.
• Locations which are poorly ventilated.
• Locations where the relative humidity drops below 35% or
exceeds 85% RH, or where condensations occurs.
• Locations where there are corrosive gas or flammable gas
• Locations where there are much dust, sodium, or iron powder.
• Locations where water, oil, or chemicals may splash onto the
CA-CNX10U/CHX10U.
• Locations where the CA-CNX10U/CHX10U may be directly
subjected to vibration or impact.
• Locations where the CA-CNX10U/CHX10U may be affected
by radiation noise or static electricity.
• When installing multiple repeaters, keep the interval of more
than 10 mm between repeaters.
Checking the Package Contents
This package include the following items. Make sure that all of the items are in
the package.
CA-CNX10U/CA-CHX10U . . . . . . . . . . . . . . . . . . . . . . . . 1 (either model)
Instruction Manual (this document)
Safety Precautions
Symbols
The following symbols are used for the list of precautions to ensure safety and
to prevent personal injury and/or property damage when using the device.
Failure to follow the instructions may lead to injury.
Failure to follow instructions may lead to product damage.
(product malfunctions, etc.)
Note
Provides additional information on proper operation.
General precautions
• Verify that this device is operating normally in terms of functionality and
performance before the start of work and before the start of device operation.
• Take appropriate safety measures to avoid any damage in case of device
failure.
• KEYENCE is unable to guarantee the function or performance of the CACNX10U/CHX10U if it is used in a manner that differs from the CACNX10U/CHX10U specifications contained in this manual or if the CACNX10U/CHX10U is modified.
• The functions and performance of the CA-CNX10U/CHX10U may not be
satisfactory depending on the operating conditions or operating environment if it is used in combination with other devices. Use it with other
devices only after careful consideration.
• Do not use the CA-CNX10U/CHX10U for protecting the human body.
• Turn off the power of the CA-CNX10U/CHX10U immediately
if one of the following incidents occurs. If you continue to
use the device while the abnormality persists, fire, electric
shock, or malfunction may result. Contact your KEYENCE
office for repair service.
When liquid such as water, oil, and chemicals or other
foreign materials enter inside the unit
When the strong impact is applied or the housing is damaged
When smoke, foul odor or abnormal noise is emitted from
the unit
• Do not disassemble or modify the unit, or connect it to anything other than compatible devices. Failure to do so may
result in fire, electrical shock, or equipment malfunction.
• Be sure to power off the CA-CNX10U/CHX10U and its
accessories, when you plug/unplug the cable. Otherwise a
fire, electrical shock, burn or malfunction could result.
Tips on Correct Use
Compatible devices
There are two types prepared for this unit.: for normal camera and high-speed
camera. Each unit has a restriction for connectable cameras, cables and controllers.
Note that the unit may be damaged if incompatible cameras,
cables or controllers are connected.
Handling
• In case of transportation, use the same packaging as when
the unit was delivered to avoid damage.
• If the unit has any dirt on it, wipe it off with a cloth moistened
with a mild detergent, then rub with a dry cloth. Do not rub
with a wet cloth, benzene, thinner, or alcohol. Doing so could
change the color or shape of the unit.
Mounting
Apply appropriate torque specified below or lower when mounting the following units.
CA-CNX10U/CA-CHX10U (penetrating hole x 2) . . . . . . . . .0.5 Nm
Tighten the cable connectors until the rotation part stops rotating. The
unit may not operate normally if the rotation part is loosely tightened.
Notes for CE Marking
We have confirmed that CA-CNX10U/CA-CHX10U comply with the essential
requirements of EMC Directive in system configuration with the compatible
controllers. Therefore, when using this unit in EU Member States, be sure to
read user's manuals of the compatible controllers.
Connecting the repeater
Part names and functions
(1) Camera connector (CAMERA side) .............. Connect to the camera.
(2) Output connector (CONTROLLER side) ....... Connect to the controller.
Connection example
• For 1-step connection
*Use the dedicated cable for the repeater between the camera and the
repeater (A) and use the camera cable between the repeater and the controller (B).
• For 2-step connection
B
2
.
camera
Controller
Flex resistance for
high-speed camera
Camera
AA
*Use the dedicated cables for the repeater between the repeater and the
camera, and between repeaters. Use the camera cable between the controller and the repeater (B).
Do not connect the camera control unit*1 between this unit and
the controller when using a compact camera*
The device may be damaged.
1
*
CV/XG-S
2
*
For cameras of model numbers of CV/XG-S
Type of extension cable
3 m cable CA-CN3X CA-CN3RX CA-CN3LX CA-CH3X
10 m cable CA-CN10X CA-CN10RX CA-CN10LX CA-CH10X CA-CH10RX
17 m cable* CA-CN17X CA-CN17RX CA-CN17LX
*Only CV/XG-035C/M type of camera can be used.
U
Standard
Flex
resistance
L-type
connector
.
For high-speed
Page 2
Model name Cable length (L) Weight
CA-CN3X 3m
Approx. 200g
CA-CN10X 10m
Approx. 600g
CA-CN17X 17m
Approx. 990g
CA-CH3X 3m
Approx. 270g
CA-CH10X 10m
Approx. 820g
CA-CN3RX 3m
Approx. 190g
CA-CN10RX 10m
Approx. 540g
CA-CN17RX 17m
Approx. 900g
CA-CH10RX 10m
Approx. 740g
CA-CN3LX 3m
Approx. 210g
CA-CN10LX 10m
Approx. 610g
CA-CN17LX 17m
Approx. 1000g
Maximum cable length for compatible controllers and cameras
For repeater connection, maximum of 2-step connection is possible. For connection-possible number of steps and maximum cable length, see the chart
below.
For extension, do not allow the cable length and connection steps to go
beyond their maximum limits.
Controller*3Camera
CV-3001/
CV-3501
CV-035C/M
CV-S035C/M 1 step 20m
CV-200C/M 2 steps 30m
CV-S200C/M
CV-5000/
CV-5500/
CV-5700/
CV-X100/
CV-X150/
CV-X170
CV-035C/M
CV-S035C/M 1 step 20m
CV-200C/M 2 steps 30m
CV-S200C/M
CV-H035C/M
CV-H100C/M 2 steps 30m
CV-H200C/M 1 step 20m
CV-H500C/M 1 step 20m
XG-7000/
XG-7500/
XG-7700/
XG-8000/
XG-8500/
XG-8700/
XG-8800/
XG-8500L/
XG-8700L/
XG-8800L
XG-8500L/
XG-8700L/
XG-8800L
XG-035C/M
XG-S035C/M 1 step 20m
XG-200C/M 2 steps 30m
XG-S200C/M
XG-H035C/M
XG-H100C/M 2 steps 30m
XG-H200C/M 1 step 20m
XG-H500C/M 1 step 20m
XG-HL02M
XG-HL04M 2 steps 30m
XG-HL08M 2 steps 30m
Compatible
repeater
CA-CNX10U
CA-CNX10U
CA-CHX10U
CA-CNX10U
CA-CHX10U
CA-CHX10U
Cable length specification
Maximum number of
connection steps
2 steps/1 step ( *1)
2 steps/1 step ( *2)
2 steps/1 step ( *1)
2 steps/1 step ( *2)
2 steps 30m
2 steps/1 step ( *1)
2 steps/1 step ( *2)
2 steps 30m
2 steps 30m
Maximum cable
length
51m/34m (*1)
30m/20m (*2)
51m/34m (*1)
30m/20m (*2)
51m/34m (*1)
30m/20m (*2)
*1 When reading parts less than 350 lines, the number of maximum connection
steps is 1 and the maximum cable length is 34m.
*2 When reading parts less than 1000 lines, the number of maximum connection
steps is 1 and the maximum cable length is 20m.
*3 The controllers and camera expansion units shipped after September 14,
2009 are compatible with the repeater connection.
Power consumption list for controllers when the repeater is
connected
The rated power consumption increases when the repeater is connected.
Controller type
Connected
camera
CV-3001 2 1.6(1.4)A
CV-3501
CV-5001 2 2.5(2.2)A
CV-5501
CV-5701
XG-7000
XG-7500
XG-7700
XG-8000
XG-8500/8700
XG-8800
XG-8500L
XG-8700L
XG-8800L
CV-X100 2 2.2(1.9)A
CV-X150
CV-X170
Power consumption when the repeater is connected
(When not connected)
2 2.1(1.8)A
4 3.4(2.8)A
2 2.7(2.4)A
4 3.8(3.2)A
2 2.7(2.4)A
4 3.8(3.2)A
2 2.5(2.2)A
4 3.4(2.8)A
2 2.7(2.4)A
4 3.8(3.2)A
2 2.7(2.4)A
4 3.8(3.2)A
2 3.0(2.9)A
4 3.8(3.5)A
2 3.2(3.0)A
4 4.1(3.8)A
2 3.2(3.0)A
4 4.1(3.8)A
6 4.9(4.4)A
8 5.8(5.0)A
1 2.6(2.4)A
2 2.8(2.5)A
1 2.8(2.7)A
2 3.3(3.0)A
1 2.5(2.4)A
2 2.7(2.5)A
3 3.0(2.7)A
4 3.0(2.8)A
2 2.8(2.5)A
4 3.4(2.8)A
2 3.1(2.8)A
4 3.7(3.1)A
Specifications
Product name
Repeater for camera cable extension
(For normal camera)
Model CA-CNX10U CA-CHX10U
CV/XG-035C/M
Connection camera
CV/XG-S035C/M
CV/XG-200C/M
CV/XG-S200C/M
Transfer system Digital serial transfer
When connecting CV/XG-035C/M:
Environment
resistance
Ambient
temperature
Ambient
humidity
0 to +50 °C
When connecting other cameras:
0 to + 40 °C
35 to 85%RH (No condensation)
Dimensions 112.6 (W) × 26 (D) × 21 (H)
Weight Approx. 60g
Repeater for camera cable extension
(For high-speed camera)
CV/XG-H035C/M
CV/XG-H100C/M
CV/XG-H200C/M
CV/XG-H500C/M
XG-HL02/04/08M
0 to +40 °C
Outer Dimensions
CA-CNX10U/CHX10U
When the cable is attached
CA-CN3X/CN10X/CN17X
CA-CH3X/CH10X
Ø12.5
CA-CN3LX/CN10LX/CN17LX
31.2
Ø14
38
(213)
Ø7.2
Ø6.1
Units: mm
Units: mm
43L43
Units: mm
43L
CA-CNX10U/CHX10U
(85)(85)
6
CA-CN3RX/CN10RX/CN17RX
CA-CH10RX
Ø12.5
Ø14
Ø12.5
Ø12.5
112.6
105
98
19
3.5
11
3.5
2xØ3.6
Through-hole
Ø7.6
53.9L53.9
Units: mm
26
6
Units: mm
Ø14
21
11.5
Ø12.5
Page 3
WARRANTIES AND DISCLAIMERS
(1) KEYENCE warrants the Products to be free of defects in materials and
workmanship for a period of one (1) year from the date of shipment. If any
models or samples were shown to Buyer, such models or samples were
used merely to illustrate the general type and quality of the Products and
not to represent that the Products would necessarily conform to said
models or samples. Any Products found to be defective must be shipped to
KEYENCE with all shipping costs paid by Buyer or offered to KEYENCE
for inspection and examination. Upon examination by KEYENCE,
KEYENCE, at its sole option, will refund the purchase price of, or repair or
replace at no charge any Products found to be defective. This warranty
does not apply to any defects resulting from any action of Buyer, including
but not limited to improper installation, improper interfacing, improper
repair, unauthorized modification, misapplication and mishandling, such as
exposure to excessive current, heat, coldness, moisture, vibration or
outdoors air. Components which wear are not warranted.
(2) KEYENCE is pleased to offer suggestions on the use of its various
Products. They are only suggestions, and it is Buyer's responsibility to
ascertain the fitness of the Products for Buyer’s intended use. KEYENCE
will not be responsible for any damages that may result from the use of the
Products.
(3) The Products and any samples ("Products/Samples") supplied to Buyer are
not to be used internally in humans, for human transportation, as safety
devices or fail-safe systems, unless their written specifications state
otherwise. Should any Products/Samples be used in such a manner or
misused in any way, KEYENCE assumes no responsibility, and additionally
Buyer will indemnify KEYENCE and hold KEYENCE harmless from any
liability or damage whatsoever arising out of any misuse of the Products/
Samples.
(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE
PROVIDED WITH NO OTHER WARRANTIES WHATSOEVER. ALL
EXPRESS, IMPLIED, AND STATUTORY WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT
OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED.
IN NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE
LIABLE TO ANY PERSON OR ENTITY FOR ANY DIRECT, INDIRECT,
INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES
(INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING
FROM LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF
INFORMATION, LOSS OR INACCURACY OF DATA, LOSS OF
PROFITS, LOSS OF SAVINGS, THE COST OF PROCUREMENT OF
SUBSTITUTED GOODS, SERVICES OR TECHNOLOGIES, OR FOR
ANY MATTER ARISING OUT OF OR IN CONNECTION WITH THE USE
OR INABILITY TO USE THE PRODUCTS, EVEN IF KEYENCE OR ONE
OF ITS AFFILIATED ENTITIES WAS ADVISED OF A POSSIBLE THIRD
PARTY’S CLAIM FOR DAMAGES OR ANY OTHER CLAIM AGAINST
BUYER. In some jurisdictions, some of the foregoing warranty disclaimers
or damage limitations may not apply.
BUYER'S TRANSFER OBLIGATIONS:
If the Products/Samples purchased by Buyer are to be resold or delivered
to a third party, Buyer must provide such third party with a copy of this
document, all specifications, manuals, catalogs, leaflets and written
information provided to Buyer pertaining to the Products/Samples.
E 1101-3
Page 4
Copyright (c) 2012 KEYENCE CORPORATION. All rights reserved.
12152E 1062-1 96M12152
Printed in Japan
Loading...