KVT-532DVD KVT-532DVDM
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
DVD
DVD
© B54-4642-00/00 (MW/M2W/XW)
Accessories
1
..........1
2
..........1
3
..........2
4
..........1
5
..........4
6
..........4
2 | KVT-532DVD/KVT-532DVDM
Installation Procedure
1.To prevent a short circuit, remove the key from the ignition and disconnect the - battery.
2.Make the proper input and output wire connections for each unit.
3.Connect the speaker wires of the wiring harness.
4.Connect the wiring harness wires in the following order: ground, battery, ignition.
5.Connect the wiring harness connector to the unit.
6.Install the unit in your car.
7.Reconnect the - battery.
8.Press the reset button.
2WARNING
If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.
¤
•Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.
•Make sure to ground the unit to a negative 12V DC power supply.
•Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.
•Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.
•If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.
•If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.
•If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening.
•If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.
•Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.
•Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.
•When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal.
•After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
•Mount the unit so that the mounting angle is 30° or less.
•This unit has the cooling fan (page 5) to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.
English | 3
Connecting Wires to Terminals
Car fuse box (Main fuse)
Ignition key switch
ACC
Ignition wire (Red)
Battery wire (Yellow)
Car fuse box
Ground wire (Black)- (To car chassis)
+–
USB device
(commercially available) USB connector
If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.
Battery
FUSE ( 15A )
Connect to the vehicle's parking brake detection |
|
|
|
|
switch harness. |
Parking sensor wire (Light Green) |
|
|
|
|
|
|
|
|
PRK SW For the sake of safety, be sure to connect the parking sensor. |
|
|
|
Connect to vehicle’s reverse lamp harness when |
Reverse sensor wire (Purple/White) |
|
using the optional rear view camera. |
|
|
To car light control switch |
Dimmer control wire (Orange/White) |
|
|
||
To use the steering wheel remote control feature, |
|
Steering remote control input (Light Blue/Yellow) |
you need to an exclusive remote adapter (not |
To steering remote |
|
supplied) matches your car is required.
Connect to the terminal that is grounded when either the telephone rings or during conversation.
To connect the Kenwood navigation system, consult your navigation manual.
Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna.
When using the optional power amplifier, connect to its power control terminal.
Mute wire (Brown)
Motor antenna control wire (Blue)
Power control wire (Blue/White)
If no connections are made, do not let the cable come out from the tab.
4 | KVT-532DVD/KVT-532DVDM
Cooling fan
Antenna Cord
Do not connect.
FM/AM antenna input
Wiring harness (Accessory 1)
Wiring harness |
AV IN |
(Accessory 2) |
|
REAR VIEW
CAMERA
Audio/Visual input / Rear View Camera Input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
LFRONT
RFRONT
P. CONT LREAR
RREAR
|
|
|
|
|
Audio/Visual Output |
|
|
|
|
|
• Visual output (Yellow) |
|
|
|
|
|
• Audio left output (White) |
|
|
|
|
|
|
AV OUT |
|
|
|
|
• Audio right output (Red) |
REAR/SUB |
|
|
|
|
Rear/Subwoofer Preout |
|
|
|
|
• Audio left output (White) |
|
WOOFER |
|
|
• Audio right output (Red) |
||
|
|
|
|
|
|
|
|
|
|
Front Preout |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FRONT |
|
|
|
|
• Audio left output (White) |
|
|
|
|
|
• Audio right output (Red) |
White/Black
To front left speaker
+
White Gray/Black
To front right speaker
+
Gray Green/Black
To rear left speaker
+
Green Purple/Black
To rear right speaker
Purple +
English | 5
Optional Accessory Connection
iPod
(commercially available)
KCA-iP300V |
|
||
(Optional Accessory) |
iPod AUDIO |
||
|
|
|
|
|
|
|
IN |
Audio Input
Resistance-free stereo type mini plug (3.5Ф)
Audio Output (Black)
Visual Input (Yellow)
Resistance-free mini plug (3.5Ф)
Visual Output (Yellow)
USB terminal
USB terminal
KCA-BT200 input (Optional Accessory)
TV Tuner
(Optional Accessory)
TVANTENNAINPUT
TOMONITORUNIT
Connection cable (Included in the TV tuner)
Connection cable
(Included in the Navigation System)
Navigation System
(Optional Accessory)
6 | KVT-532DVD/KVT-532DVDM
Installation/Removing the Unit
Installation
Firewall or metal support
Screw (M4X8) (commercially available)
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.
Self-tapping screw |
Metal mounting strap |
(commercially available) |
(commercially available) |
Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
English | 7
Installation/Removing the Unit
Removing the Hard Rubber Frame (escutcheon)
1.Engage the catch pins on the removal tool 3 and remove the two locks on the lower level.
Lower the frame and pull it forward as shown in the figure.
Escutcheon (Accessory 4)
Removal Tool (Accessory 3)
Catch
Lock
Removing the Unit
1.Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>.
2.Remove the Hex-head screw with integral washer (M4 × 8) on the back panel.
3.Insert the two removal tools 3 deeply into the slots on each side, as shown.
Removal Tool (Accessory 3)
⁄
•The frame can be removed from the top side in the same manner.
2.When the lower level is removed, remove the upper two locations.
4.Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside.
⁄
•Be careful to avoid injury from the catch pins on the removal tool.
5.Pull the unit all the way out with your hands, being careful not to drop it.
8 | KVT-532DVD/KVT-532DVDM
Installing in Japanese-made Cars
Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●"
or
Accessory 5 (M5x6mm) or Accessory 6 (M5x7mm)
Car Bracket
Accessory 5 (M5x6mm) or Accessory 6 (M5x7mm)
Screws (included in audio unit package)
|
Screws (included in |
Audio unit or others |
audio unit package) |
|
⁄
•Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.
English | 9
Installing in Japanese-made Cars
Installation on Toyota Car using Brackets at Holes shown by "●"
or
When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides.
1. Mount the bracket at each side.
Car Bracket
Accessory 5 (M5x6mm)
Accessory 5 (M5x6mm)
Screws (included in audio unit package)
Screws (included in audio unit package)
2. Bend each end of case to fix the bracket.
Use a flat-blade screwdriver or pliers, and bend each case tab into the hole of installation bracket to fix the bracket.
10 | KVT-532DVD/KVT-532DVDM