JLG LSS Verticals Service Manual

Service and Maintenance Manual

Model

E400A/AJP

E400A/AJPnarrow

M400A/AJP

M400A/AJPnarrow

P/N - 3121125

March 20, 2014

INTRODUCTION

SECTION A. INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

A GENERAL

This section contains the general safety precautions which must be observed during maintenance of the aerial platform. It is of utmost importance that maintenance personnel pay strict attention to these warnings and precautions to avoid possible injury to themselves or others, or damage to the equipment. A maintenance program must be followed to ensure that the machine is safe to operate.

MODIFICATION OR ALTERATION OF AN AERIAL WORK PLATFORM SHALL BE MADE ONLY WITH WRITTEN PERMISSION FROM THE MANUFACTURER.

The specific precautions to be observed during maintenance are inserted at the appropriate point in the manual. These precautions are, for the most part, those that apply when servicing hydraulic and larger machine component parts.

Your safety, and that of others, is the first consideration when engaging in the maintenance of equipment. Always be conscious of weight. Never attempt to move heavy parts without the aid of a mechanical device. Do not allow heavy objects to rest in an unstable position. When raising a portion of the equipment, ensure that adequate support is provided.

C MAINTENANCE

FAILURE TO COMPLY WITH SAFETY PRECAUTIONS LISTED IN THIS SECTION COULD RESULT IN MACHINE DAMAGE, PERSONNEL INJURY OR DEATH AND IS A SAFETY VIOLATION.

• ENSURE REPLACEMENT PARTS OR COMPONENTS ARE IDENTICAL OR EQUIVALENT TO ORIGINAL PARTS OR COMPONENTS.

• NO SMOKING IS MANDATORY. NEVER REFUEL DURING ELECTRICAL STORMS. ENSURE THAT FUEL CAP IS CLOSED AND SECURE AT ALL OTHER TIMES.

• REMOVE ALL RINGS, WATCHES AND JEWELRY WHEN PERFORMING ANY MAINTENANCE.

• DO NOT WEAR LONG HAIR UNRESTRAINED, OR LOOSE-FITTING CLOTHING AND NECKTIES WHICH ARE APT TO BECOME CAUGHT ON OR ENTANGLED IN EQUIPMENT.

• OBSERVE AND OBEY ALL WARNINGS AND CAUTIONS ON MACHINE AND IN SERVICEMANUAL.

• KEEP OIL, GREASE, WATER, ETC. WIPED FROM STANDING SURFACES AND HAND HOLDS.

• USE CAUTION WHEN CHECKING A HOT, PRESSURIZED COOLANT SYSTEM.

• NEVER WORK UNDER AN ELEVATED BOOM UNTIL

SINCE THE MACHINE MANUFACTURER HAS NO DIRECT CONTROL OVER THE FIELD INSPECTION AND MAINTENANCE, SAFETY IN THIS AREA RESPONSIBILITY OF THE OWNER/OPERATO R.

BOOM HAS BEEN SAFELY RESTRAINED FROM ANY MOVEMENT BY BLOCKING OR OVERHEAD SLING, OR BOOM SAFETY PROP HAS BEEN ENGAGED.

• BEFORE MAKING ADJUSTMENTS, LUBRICATING OR PERFORMING ANY OTHER MAINTENANCE, SHUT OFF ALL POWER CONTROLS.

B HYDRAULIC SYSTEM SAFETY

• BATTERY SHOULD ALWAYS BE DISCONNECTED-

It should be noted that the machines hydraulic systems operate at extremely high potentially dangerous pressures. Every effort should be made to relieve any system pressure prior to disconnecting or removing any portion of the system.

3121125 – JLG Lift – A-1

DURING REPLACEMENT OF ELECTRICAL COMPONENTS.

• KEEP ALL SUPPORT EQUIPMENT AND ATTACHMENTS STOWED IN THEIR PROPER PLACE.

• USE ONLY APPROVED, NONFLAMMABLE CLEANING SOLVENTS.

INTRODUCTION

REVISON LOG

Original Issue - August 15, 2000 Revised - March 26, 2001 Revised - October 1, 2001 Revised - December 18, 2001 Revised - April 11, 2002 Revised - May 25, 2004 Revised - September 17, 2007 Revised - January 18, 2008 Revised - January 27, 2009 Revised - January 7, 2013 Revised - April 26, 2013 Revised - October 23, 2013 Revised - March 20, 2014

A-2 – JLG Lift – 3121125

TABLE OF CONTENTS

SECTION NO. TITLE PAGE NO.

SECTION A - INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

A General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1

B Hydraulic System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

C Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

SECTION 1 - SPECIFICATIONS

1.1 Operating specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.2 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.3 Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.4 Drive System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.5 Hydraulic Pump/Electric Motor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.6 Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.7 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.8 Dimensional Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

1.9 Function Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Machine Orientation When Doing Function Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.10 Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.11 Cylinder Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1.12 Major Component Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1.13 Critical Stability Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1.14 Pressure Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

1.15 Serial Number Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

1.16 Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1.17 Operator Maintenance & Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8

SECTION 2 - GENERAL

2.1 Machine Preparation, Inspection, and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Preparation, Inspection, and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Pre-Start Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Pre-Delivery Inspection and Frequent Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Annual Machine Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2 Service and Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Safety and Workmanship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Cleanliness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Components Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Component Disassembly and Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Pressure-Fit Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Gaskets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Bolt Usage and Torque Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Hydraulic Lines and Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Hydraulic System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Lubrication and Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

3121125 – JLG Lift – i

TABLE OF CONTENTS

SECTION NO. TITLE PAGE NO.

2.3 Lubrication and Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Hydraulic System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Changing Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.4 Cylinder Drift Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

Platform Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Cylinder Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.5 Pins and Composite Bearing Repair Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

2.6 Welding on JLG Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Do the Following When Welding on JLG Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Do NOT Do the Following When Welding on JLG Equipment . . . . . . . . . . . . . . . . . . . . . . . 2-5

SECTION 3 - CHASSIS & TURNTABLE

3.1 Tires & Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Tire Inflation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Tire Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Tire Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Wheel Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Wheel Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 Spindle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Setting Wheel Bearing End Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Greasing Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.3 Drive Hub (Part No. 2780236) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Dissembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Disassembly of the first stage planetary assembly (7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Disassembly of second stage planet gears (1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Assembly of first stage planetary assembly (7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Assembly of end cover unit (8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Final Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Initial Start-up And After Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Oil Change Interval-Gear Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Setting of Tapered Roller Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Securing of the Shaft Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

3.4 Drive Brake - Mico . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8

Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Bleeding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

3.5 Speed Sensor Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

Adjustment Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Speed Sensor Installation Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Verification w/ Analyzer Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

3.6 Positrac/Tilt module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

3.7 Swing Motor - S/N 0300135649 to Present. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

Preparation Before Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

Disassembly and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30

One Piece Stator Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

Two Piece Stator Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38

Final Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38

ii – JLG Lift – 3121125

TABLE OF CONTENTS

SECTION NO. TITLE PAGE NO.

3.8 Swing Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-39

Turntable Bearing Mounting Bolt Condition Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39

Wear Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39

Replacement of Swing Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41

Swing Bearing Torque Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43

Checking Worm Gear End Play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43

Adjusting End Play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43

3.9 Battery Maintenance and Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-45

Battery Maintenance, Quarterly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-45

Charging Sequence of Remote LED Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-45

Battery Charging (On Board Charger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-47

Optional On Board Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-47

3.10 Battery Charger (S/N 0300059350 to Present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-49

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-49

Maintenance Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-49

Battery Charger Fault Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-49

Excessive Battery Watering Requirements or Strong Sulphur (Rotten Egg) Smell . . . . . . . 3-52

Checking/Changing the Battery Charger Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53

3.11 Generator (Prior to S/N 88539) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-54

Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Dynamo and Dynamo Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Dynamo Output Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Control Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Start Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Engine Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Start Control Relay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Fuel Control Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Fuel Solenoid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Engine Oil Temperature Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Alternator Output Current Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Engine Speed Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Engine Low Oil Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

Timing Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54

To Connect the JLG Control System Analyzer to the Generator . . . . . . . . . . . . . . . . . . . . . 3-57

Alarms and Fault Flash Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-57

Output Current and Voltage Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-59

Priming the Fuel Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-60

3.12 Generator (S/N 88539 to Present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-61

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61

Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61

Dynamo and Dynamo Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61

Dynamo Output Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61

Control Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61

Start Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63

Engine Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63

Start Control Relay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63

Fuel Control Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-64

Glow Plug Control Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-64

Glow Plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-64

Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-65

Fuel Solenoid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-65

3121125 – JLG Lift – iii

TABLE OF CONTENTS

SECTION NO. TITLE PAGE NO.

Engine Low Oil Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-65

Engine Oil Temperature Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-65

Alternator Output Current Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-66

Engine Speed Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-66

RBS Engine/Generator Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-66

Warnings and Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67

System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67

System Status and Performance Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67

System Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67

RBS Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-68

RBS shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-68

RBS Alarms and Flash Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-69

Resetting the RBS Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-69

Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-69

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-70

APU Engine Start Battery Boosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-71

3.13 Supplementary fuse for apu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-72

Tools And Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-72

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-72

SECTION 4 - BOOM & PLATFORM

4.1 Boom Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

4.2 Upper (Main) Boom Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

4.3 Mid Boom Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4.4 Lower Boom Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4.5 Upper Boom Telescope Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

4.6 Mid and Lower Lift Cylinder Bleeding Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

4.7 Wear Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

4.8 Boom Synchronizing Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8

4.9 Articulating Jib Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

4.10 Footswitch Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

4.11 Boom Limit Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

iv – JLG Lift – 3121125

TABLE OF CONTENTS

SECTION NO. TITLE PAGE NO.

4.12 Helac Rotary actuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12

Theory Of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Tools Required for Assembly/Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Installing Counterbalance Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

Testing the Actuator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

Installation and Bleeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

4.13 Powertrack Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27

Removing a Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Installing a New Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

Replacing Fixed End Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Replacing Moving End Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37

SECTION 5 - HYDRAULICS

5.1 Lubricating O-Rings in the Hydraulic System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Cup and Brush. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Dip Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Spray Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Brush-on Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

5.2 Cylinders - Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3

Double Acting Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

5.3 Cylinder Checking Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Cylinder Without Counterbalance Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Cylinders With Single Counterbalance Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Cylinders With Dual Counterbalance Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

5.4 Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-14

Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

Cleaning and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16

5.5 Pressure Setting Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-20

Main Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

Upper Lift Down Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

Lower Lift Down Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

Telescope Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

Platform Level Up Relief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

Platform Level Down Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

Steer Relief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

Jib Lift (Up and Down) Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

Jib Swing Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

Releveling Valve Relief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

3121125 – JLG Lift – v

TABLE OF CONTENTS

SECTION NO. TITLE PAGE NO.

SECTION 6 - JLG CONTROL SYSTEM

6.1 JLG Control System Analyzer Kit Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

To Connect the JLG Control System Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Using the Analyzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Changing the Access Level of the Hand Held Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Adjusting Parameters Using the Hand Held Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Machine Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Machine Personality Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

Machine Configuration Programming Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

Level Vehicle Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Help Descriptions and Fault Flash Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Analyzer Diagnostics Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21

System Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22

SECTION 7 - BASIC TROUBLESHOOTING, ELECTRICAL INFORMATION, & SCHEMATICS

7.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

7.3 Multimeter Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Backprobing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Min/Max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Voltage Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Resistance Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20

Continuity Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20

Current Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

7.4 Checking Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-21

Basic Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

Limit Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

Automatic Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

Switch Wiring - Low Side, High Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

7.5 Applying Silicone Dielectric Compound to Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . .7-22

7.6 AMP Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-23

Applying Silicone Dielectric Compound to AMP Connectors. . . . . . . . . . . . . . . . . . . . . . . . 7-23

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23

Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

Wedge Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

Service - Voltage Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

7.7 Deutsch Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-27

DT/DTP Series Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27

DT/DTP Series Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27

HD30/HDP20 Series Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28

HD30/HDP20 Series Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28

vi – JLG Lift – 3121125

LIST OF FIGURES

FIGURE NO. TITLE PAGE NO.

1-1. Serial Number Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-2. Operator Maintenance & Lubrication Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

1-3. Torque Chart (SAE Fasteners - Sheet 1 of 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-11

1-4. Torque Chart (SAE Fasteners - Sheet 2 of 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12

1-5. Torque Chart (SAE Fasteners - Sheet 3 of 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13

1-6. Torque Chart (SAE Fasteners - Sheet 4 of 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14

1-7. Torque Chart (METRIC Fasteners - Sheet 5 of 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

1-8. Torque Chart (METRIC Fasteners - Sheet 6 of 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

1-9. Torque Chart (METRIC Fasteners - Sheet 7 of 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17

2-1. Engine Operating Temperature Specifications - Kubota . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

3-3. Spindle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

3-1. Drive Hub - Cutaway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7

3-2. Drive Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9

3-3. Speed Sensor Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

3-4. Frame Mounted Electrical Components - Sheet 1 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

3-5. Frame Mounted Electrical Components - Sheet 2 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14

3-6. Voltage Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

3-7. Steering Components and Spindles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

3-8. Drive Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19

3-9. Tilt Sensor Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20

3-10. Swing Motor - Cutaway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-21

3-11. Swing Motor - Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23

3-12. Swing Bearing Feeler Gauge Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-39

3-13. Swing Bearing Tolerance Measuring Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-40

3-14. Swing Bearing Tolerance Boom Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41

3-15. Swing Bearing Torquing Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-42

3-16. Swing Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-44

3-17. Remote LED Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-45

3-18. Battery Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-46

3-19. Batteries and Battery Charger (Prior to S/N 0300059350) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-47

3-20. On Board Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-48

3-21. Battery Charger ((S/N 0300059350 to Present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-50

3-22. Generator Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-55

3-23. Generator System Analyzer Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-58

3-24. Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-62

4-1. Location of Components - Boom Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

4-2. Upper Boom Lift Cylinder Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4-3. Mid Boom Lift Cylinder Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4-4. Lower Boom Lift Cylinder Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

4-5. Upper Telescope Cylinder Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

4-6. Wear Pad Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

4-7. Location of Components - Articulating Jib Boom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4-8. Jib/Platform Components and Attaching Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9

4-9. Platform Support Torque Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

3121125 – JLG Lift – vii

LIST OF FIGURES

FIGURE NO. TITLE PAGE NO.

4-10. Boom Limit Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11

4-11. Rotary Actuator (Exploded View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-13

4-12. Rotary Actuator (Cutaway View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-14

4-13. Rotator Counterbalance Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-24

5-1. Jib Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4

5-2. Level Cylinder - A Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

5-3. Level Cylinder - AJ & AJP Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

5-4. Lower Lift Cylinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

5-5. Mid Lift Cylinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8

5-6. Upper Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9

5-7. Master Cylinder - A Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10

5-8. Master Cylinder - AJ Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11

5-9. Steer Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

5-10. Telescope Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13

5-11. Cylinder Barrel Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

5-12. Capscrew Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-15

5-13. Cylinder Rod Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15

5-14. Tapered Bushing Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-15

5-15. Gar-Max Bearing Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16

5-16. Rod Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16

5-17. Wiper Seal Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-17

5-18. Installation of Head Seal Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-17

5-19. Piston Seal Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-17

5-20. Tapered Bushing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-18

5-21. Seating the Tapered Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-18

5-22. Poly-Pak Piston Seal Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-18

5-23. Rod Assembly Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-18

5-24. Jib Valve Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-22

5-25. Brake/Steer Valve Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-23

5-26. HydraForce Cartridge Torque Value Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-24

5-27. Main Valve Components Prior to S/N 62642 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-25

5-28. Main Valve Components S/N 62642 to Present . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-26

6-1. Hand Held Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

6-2. Control Module Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6-3. Analyzer Flow Chart (Software Version 3.x) - Sheet 1 of 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18

6-4. Analyzer Flow Chart (Software Version 3.x) - Sheet 2 of 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19

6-5. Analyzer Flow Chart (Software Version 3.x) - Sheet 3 of 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20

7-1. Voltage Measurement (DC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-19

7-2. Resistance Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20

7-3. Continuity Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-20

7-4. Current Measurement (DC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

7-5. Connector Assembly Figure 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-23

7-6. AMP Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-23

7-7. Connector Assembly Figure 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-24

7-8. Connector Assembly Figure 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-24

7-9. Connector Assembly Figure 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-24

7-10. Connector Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

7-11. Connector Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-26

viii – JLG Lift – 3121125

LIST OF FIGURES

FIGURE NO. TITLE PAGE NO.

7-12. DT/DTP Contact Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27

7-13. DT/DTP Contact Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-27

7-14. HD/HDP Contact Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-28

7-15. HD/HDP Locking Contacts Into Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-28

7-16. HD/HDP Contact Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-28

7-17. HD/HDP Unlocking Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-28

7-18. Electrical Components Installation - Sheet 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-30

7-19. Electrical Components Installation - Sheet 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-31

7-20. Electrical Schematic - Sheet 1 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-32

7-21. Electrical Schematic - Sheet 2 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-33

7-22. Electrical Schematic - Sheet 3 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-34

7-23. Electrical Schematic - Sheet 4 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-35

7-24. Hydraulic Schematic - M400A/E400A - Sheet 1 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-36

7-25. Hydraulic Schematic - M400A/E400A - Sheet 2 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-37

7-26. Hydraulic Schematic - M400AJ/E400AJ - Sheet 1 of 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-38

7-27. Hydraulic Schematic - M400AJ/E400AJ - Sheet 2 of 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-39

7-28. Hydraulic Schematic Component List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-40

3121125 – JLG Lift – ix

LIST OF TABLES

TABLE NO. TITLE PAGE NO.

1-1 Operating Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1-2 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1-3 Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1-4 Drive System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1-5 Hydraulic Pump/Electric Motor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1-6 Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1-7 Tire Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1-8 Dimensional Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1-9 Function Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1-10 Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

1-11 Cylinder Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1-12 Major Component Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1-13 Critical Stability Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1-14 Pressure Settings - Prior to S/N 0300062642 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

1-15 Pressure Settings - S/N 0300062642 to Present . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

1-16 Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

1-17 Mobil DTE 11M Specs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-18 Mobil EAL H Series Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

1-19 Lubrication Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8

2-1 Inspection and Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

2-2 Cylinder Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2-3 Inspection and Preventive Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

3-1 Wheel Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3-2 Drive Brake Diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10

3-3 Swing Motor Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

3-11 Battery Charger Fault Codes (Delta-Q). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-49

3-4 Battery Algorithms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-53

3-5 RBS Prestart Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-56

3-6 RBS Startup Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-56

3-7 RBS Shutdown Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-56

3-8 Generator System Flash Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-57

3-9 Controller Interface Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-66

3-10 RBS Alarms and Flash Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-69

3-11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-70

4-1 Wear Pad Thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

4-1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

5-1 Cylinder Head and Tapered Bushing Torque Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-19

5-2 Cylinder Piston Nut Torque Specifications) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-19

5-3 Holding Valve Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-19

5-4 Pressure Settings - Prior to S/N 0300062642 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22

5-5 Pressure Settings - S/N 0300062642 to Present . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-22

6-1 Personality Ranges/Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7

6-2 Machine Setup Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10

6-3 JLG Control System Flash Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

6-4 Help Descriptions and Fault Flash Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-12

6-5 DIAGNOSTICS - Menu Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-21

6-6 System Test Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-23

6-7 System Test Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24

6-8 Diagnostic Fault Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-28

7-1 Platform Assembly - Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2

7-2 Boom Assembly - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-4

7-3 Turntable Assembly - Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

7-4 Chassis Assembly - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-5 Hydraulic System - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-15

7-6 Electrical System - Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-17

. .7-10

x – JLG Lift –

SECTION 1. SPECIFICATIONS

Table 1-3. Battery Charger

Input 110 VAC,60 HZ

Output 48 VDC (25 Amps)

Batteries (8) 6 Volt, 370 Amp Hour (20 hour rate)

Table 1-4. Drive System

Drive Motor 48 VDC, 12.5 H.P. @ 3200 rpm.

continuous, rotation - reversible

Drive Brake- spring-applied, hydraulically released

Table 1-5. Hydraulic Pump/Electric Motor Assembly

Motor 48 VDC, 2.14 H.P. @ 2700 rpm.

Pump 0.098 in.[3]/rev. (1.6 cm[3]/rev.).

Pump Output 2.96 gpm (11.2 lpm) @ 3400 psi (234 Bar).

Table 1-6. Generator

Alternator Output 58 volts @ 45 Amps

RPM’s under max. load 3100

Start Battery 12 volts

Engine Oil 10W30 (Refer to Engine Manual)

Dynamo 12 volt, 15 amp DC

Dynamo Output Fuse 20 amps DC

Control Fuse 15 amps DC

Table 1-7. Tire Data

Size E/M400A, E/M400AJP

240/55 - 17.5 Pneu. non marking 240/55 - 17.5 Foam Filled 26 x 7 x 20 non marking 240/55 - 17.5 Pneu. 240/55 - Foam Filled

Size E/M400Anarrow, E/M400AJPnarrow

25 x 7 x 12 - non marking 22 x 6 x 17.5 - non marking

Tire Pressure (pneumatic) 90 psi. (6.2 Bar)

Max. Tire Load E/M 400Anarrow E/M400AJP E/M400AJPnarrow

5160 lbs. (2343 kg) 6300 lbs. (2860 kg) 7200 lbs. (3268 kg)

Ground Bearing Pressure E/M 400A E/M 400Anarrow E/M400AJP E/M400AJPnarrow

80 psi (5.6kg/cm2) 95 psi (6.6 kg/cm

)

80 psi (5.6 kg/cm

)

185 psi (13.0 kg/cm

)

SECTION 1 - SPECIFICATIONS

1.1 OPERATING SPECIFICATIONS

Table 1-1. Operating Specifications

Maximum Work Load (Capacity) U nr e st r i ct e d:

Maximum Travel Grade (Gradeablility

Maximum Travel Grade (Side Slope)

Machine Weight (GVW) E 40 0 An a rr ow M 40 0 An a rr ow E 40 0 AJ P M 40 0 AJ P E 40 0 AJ Pn a rr ow M 40 0 AJ Pn a rr ow

System Voltage 48 volts

Battery Life per Charge 7 hours continuous

Battery Recharge Time C ha r ge r G en e ra t o r

17 hours from full discharge

500 lb. (230 kg)

30%

13100 lbs. (5942 kg) 13300 lbs. (6033 kg) 13700 lbs. (6214 kg) 13930 lbs. (6318 kg) 14900 lbs. (6759 kg) 15130 lbs. (6862 kg)

6.2 hours

1.2 CAPACITIES

Table 1-2. Capacities

Generator Fuel Tank

4 Gallons (15.1 L)

1.5 HYDRAULIC PUMP/ELECTRIC MOTOR ASSEMBLY

5°

1.6 GENERATOR

1.7 TIRES

Hydraulic Oil Tank

E/M 400A, E/M 400Anarrow

E/M400AJP, E/M400AJPnarrow

Hydraulic System (Including Tank)

Torque Hub, Drive*

*Torque hubs should be one h alf full of lubricant.

1.3 BATTERY CHARGER

1.4 DRIVE SYSTEM

3121125 – JLG Lift – 1-1

4 gallons. (15.14 liters)

5 Gallons (19 L)

9 Gallons (34.1 L)

19 ounces (0.50 L)

SECTION 1 - SPECIFICATIONS

Table 1-9. Function Speeds

Function Seconds

Main Lift Up 30-24

Main Lift Down 29-23

Turntable Swing Right & Left 360° 81-67*

Telescope Out - E400AJP, M400AJP, E400AJPn, M400AJPn

10-6

Telescope Out - E400An, M400An, E400A, M400A 18-14

Telescope In - E400AJP, M400AJP, E400AJPn, M400AJPn

15-10

Telescope In - E400An, M400An, E400A, M400A 28-23

Platform Rotate (4 ft.) - Right & Left 180° - E400AJP, M400AJP, E400AJPn, M400AJPn

20-24**

Platform Rotate (5 ft.) - Right & Left 180° - E400AJP, M400AJP

16-19**

Platform Rotate - Right & Left 180° - E400An, M400An, E400A, M400A

17-14**

Jib Up 25-26

Jib Down 24-25

Jib Swing 18-25

Lower Lift Up 33-27

Lower Lift Down 26-22

High Drive - Fwd.& Rev. E400AJP/M400AJP (200 ft.)

42-44***

3.2 mph. (5.1 kph)

High Drive - Fwd.& Rev. E400AJPn/M400AJPn (200 ft.)

45-50***

3.0 mph. (4.8 kph)

Drive above Horiz. (ANSI) - Fwd.& Rev. E400A, E400AJP/M400A, M400AJP ( 50 ft . )

50-53***

0.64 mph (1 kph)

Drive above Horiz.(ANSI)- Fwd.& Rev. E400An/ E400AJPn/M400n, M400AJPn ( 50 f t . )

78-85***

0 .44 mph. (0.7 kph)

Drive above Horiz. (CE) - Fwd.& Rev. E400AJP/ M400AJP ( 50 ft . )

107-112***

0.32 mph (0.5 kph)

Drive above Horiz.(CE) - Fwd.& Rev. E400An/ E400AJPn/M400An/ M400AJPn ( 50 f t . )

78-85***

0 .44 mph. (0.7 kph)

Drive above Horiz.(CE) - Fwd.& Rev. E400A/M400A ( 50 f t . )

67-71***

0 .48 mph. (0.8 kph)

*Swing Left to Swing Right should be within 10% of each other.

**Swing Left to Swing Right should be within 15% of each other.

***Drive Forward to Drive Reverse should be within 10% of each other.

4150273 N

1.8 DIMENSIONAL DATA 1.9 FUNCTION SPEEDS

Table 1-8. Dimensional Data

Machine Height (stowed) E /M 4 00 A JP E /M 4 00 A JP na r ro w E/M 400A E/M 400Anarrow

Machine Width E/M 400A E/M 400Anarrow E /M 4 00 A JP E /M 4 00 A JP na r ro w

Machine Length (stowed) E/M 400A E/M 400Anarrow E /M 4 00 A JP E /M 4 00 A JP na r ro w

Wheel Base 6 ft. 7.0 in. (2.00 m)

Tr ac k W i dt h E/M 400A, E/M400AJP E/M 400Anarrow, E/M400AJPnarrow

Ground Clearance E/M 400A, E/M400AJP E/M 400Anarrow, E/M400AJPnarrow

Working Height 46 ft. 0 in. (14.02 m)

Platform Height 40 ft. 0 in. (12.19 m)

Up and Over Platform Height 21 ft. 5 in. (6.55 m)

Horizontal Reach @ Maximum Up and Over E/M 400A, E/M 400Anarrow E /M 4 00 A JP, E/M400AJPnarrow

Tail Swing (Any Position) E/M 400A, E/M400AJP, E/M400AJPnarrow

- 0 in. E/M 400Anarrow - 4 in.

Turning Radius (Inside) E/M 400A E/M 400Anarrow E /M 4 00 A JP E /M 4 00 A JP na r ro w

Turning Radius (outside) 10 ft.- 4 in. (3.15 m)

E/M 400A, E/M400AJP, E/

6 ft. 7 in. (2.0 m)

6 ft. 5.75 in. (1.31m)

6 ft. 7 in. (2.0 m)

6 ft. 5.75 in. (1.97 m)

5 ft. 9 in. (1.75 m)

4 ft. 11 in. (1.50 m)

5 ft. 9 in. (1.75 m.)

4 ft. 11 in. (1.49 m.)

18 ft. 1 in. (5.50 m) 18 ft. 1 in. (5.50 m)

22.0ft. (6.7 m)

22.0 ft. (6.7 m)

Tr ac k Wi d th

5 ft. 0 in. (1.51 m)

4 ft. 3.75 in.(1.31 m)

8.5 in. (0.22 m) 5 in. (0.13 m)

21 ft. 2 in. (6.41 m)

22 ft.-5 in. (6.83 m)

Tail Swing (Any Position)

M400AJPnarrow - 0 in.

E/M 400Anarrow - 4 in.

2 ft. 0 in. (0.61 m)

2 ft. 10 in. (0.86 m)

2 ft.- 0 in. (0.61 m)

2 ft.-10 in. (0.86 m)

1-2 – JLG Lift – 3121125

SECTION 1 - SPECIFICATIONS

Machine Orientation When Doing Function Tests

1. LIFT: Boom retracted, telescope retracted. Lift up, record time. Lift down, record time.

2. SWING: Boom at full elevation, telescope retracted. Swing the turntable to the end stop. Swing the opposite direction. Record time. Swing the other direction, record time.

3. TELESCOPE: Boom at full elevation, telescope retracted. Telescope out, record time. Telescope in, record time.

4. DRIVE: Test should be done on a smooth, level surface. Start approximately 25 feet from starting point so that the unit is at a maximum speed when starting the test. Results should be recorded for a 200 foot course. Drive forward, record time. Drive reverse, record time.

5. DRIVE (ABOVE HORIZONTAL): Test should be done on a smooth, level surface. The platform speed control knob should be selected out of creep speed. This verifies that the switches are working when the boom is above horizontal. Results should be recorded for a 50 ft. course. Drive forward, record time. Drive reverse, record time.

NOTE: Stop watch should be started with the function, not

with the controller or switch.

All speed tests are run from the platform.

The platform speed control knob must be at full speed. (turned clockwise completely)

The function speeds may vary due to cold thick hydraulic oil. Tests should be run with oil tempera-

ture above 100

Some flow control functions may not work with the speed control knob in the creep position.

F. ( 3 8o C)

1.10 TORQUE SPECIFICATIONS

Table 1-10. Torque Requirements

Description Tor q ue Va l ue Interval Hours

Wheel Lugs 170 ft. lbs. (230 Nm) 150

Swing Bearing (Loctite)

* Check swing bearing bolts for security after first 50 hours of operation and every 600 hours thereafter.

190 ft. lbs.(260Nm) 50/600*

6. PLATFORM ROTATE: Platform level and completely rotated one direction. Rotate the opposite direction, record time. Rotate the other direction, record time.

7. JIB: Platform level and centered with the boom. Start with the jib down. Jib up, record time. Jib down, record time.

8. LOWER LIFT: Upper boom horizontal, telescoped in. Lower lift up, record time. Lower lift down, record time.

9. JIB SWING: Platform level and centered with the boom. Start with the jib horizontal. Begin with jib swing fully to left. Swing fully to right. Record time. Swing to the left, record time.

3121125 – JLG Lift – 1-3

SECTION 1 - SPECIFICATIONS

Table 1-12.Major Component Weights

Component LB. KG.

Platform and Support

215 97.5

Upper Boom Complete

810 367

Mid Boom Complete

550 249

Lower Boom Complete

550 249

Upper Lift Cylinder

89 40

Mid Lift Cylinder

95 43

Lower Lift Cylinder

110 50

Telescope Cylinder

85 38.5

Upper Upright

225 102

Lower Upright

97 44

Turn ta ble

948 430

Battery Box (incl. batteries)

600 272

Chassis (w/ pneu. tires)

4,295 1948

Chassis (w/ foam-filled tires)

4,695 2130

Counterweight

3850 1746

Machine Complete

11,800 5352

Jib

320 145

1.11 CYLINDER SPECIFICATIONS

NOTE: All dimensions are given in inches (in.), with the met-

ric equivalent, millimeters (mm), given in parentheses.

Table 1-11. Cylinder Specifications

Cylinder Bore Stroke Rod Dia.

Upper Lift Cylinder

Mid Lift Cylinder

Lower Lift Cylinder

Telescope Cylinder

Master Cylinder (E/M400A)

Master Cylinder (E/M400AJP)

Slave Cylinder (E/M400A)

3.00

(76.2)

3.00

(76.2)

4.00

(101.6)

2.00

(50.8)

2.00

(50.8)

3.00 (75)

2.00

(50.8)

28.3125 (719.1)

21.25

(539.7)

23.25

(590.5)

(2337)

9.375

(238.1)

11.5

(292)

9.375

(238.1)

1.50

(38.1)

1.50

(38.1)

2.25

(57.1)

1.25

(31.8)

1.00

(25.4)

1.25 (32)

1.00

(25.4)

1.12 MAJOR COMPONENT WEIGHTS

Slave Cylinder (E/M400AJP)

3.00 (75)

11.6

(295.5)

1.25 (32)

SELECT LIFTING EQUIPMENT WITH CAPACITY CAPABLE OF

Rotator Cylinder

Steer Cylinder (Double Rod)

Jib Cylinder

1-4 – JLG Lift – 3121125

1.875 (47.6)

2.50

(63.5)

63.5 (2.5)

15.250 (387.3)

4.06

(103.1)

233.6 (9.2)

1.00

(25.4)

1.75

(44.5)

44.5

(1.75)

SAFELY SUPPORTING WEIGHT.

1.13 CRITICAL STABILITY WEIGHTS

Table 1-13. Critical Stability Weights

Component KG. LB.

Counterweight

Tire & Wheel (foam-filled)

Platform (4ft [1.2 m])

Platform (5 ft. [1.5 m])

Battery (each)

DO NOT REPLACE ITEMS CRITICAL TO STABILITY WITH ITEMS OF DIFFERENT WEIGHT OR SPECIFICATION (FOR EXAMPLE: BATTERIES, FILLED TIRES, PLATFORM) DO NOT MODIFY UNIT IN ANY WAY TO AFFECT STABILITY.

1746 3850

94 207

41 90

45 100

54 120

SECTION 1 - SPECIFICATIONS

1.14 PRESSURE SETTINGS

Table 1-14. Pressure Settings - Prior to S/N 0300062642

Circuit PSI Bar

Main Control Valve

Lift Down Relief 550 38

Tower Lif t Down Relief

Telescope In Relief (A/AJ) 2150 148

Telescope In Relief (AJP) 3000 207

Platform Level Up Relief 2500 17 2

Platform Level Down Relief 1500 10 3

Brake/Steer Valve

Steer Relief

Steer Relief - AJPn

Main Relief - E400A/M400A

Main Relief - E400AJ/M400AJ

Jib Valve

Jib Relief (Up and Down)

Jib Swing Relief

Releveling Valve

Releveling Relief

1700 117

2300 159

110 0 76

3200 221

3400 234

1500 103

3000 207

1200 83

Table 1-15. Pressure Settings - S/N 0300062642 to

Present

Circuit PSI Bar

Main Control Valve

Lift Down Relief 800 55

Tower Lif t Down Relief (E/M400A) Prior to S/N 86022

Tower Lif t Down Relief (E/M400A) S/N 86022 to Present

Tower Lif t Down Relief (E/M400AJP) Prior to S/N 91053

Tower Lif t Down Relief (E/M400AJP) S/N 91053 to Present

1700 117

2600 179

1700 117

2600 179

Telescope Relief (A) 3000 207

Telescope Relief (AJ & AJP) 3100 214

Platform Level Up Relief 3000 207

Platform Level Down Relief 1200 83

Brake/Steer Valve

Steer Relief - AJP/A

Steer Relief - An

Steer Relief - AJPn

Main Relief

2300 159

110 0 7 6

1400 96.5

3400 234

Jib Valve

Jib Relief Up

Jib Swing Relief

2200 152

3000 207

Releveling Valve

Releveling Relief (E/M400A) Prior to S/N 86022

Releveling Relief (E/M400A) S/N 86022 to Present

Releveling Relief (E/M400AJP) Prior to S/N 91053

Releveling Relief (E/M400AJP) S/N 91053 to Present

1200 83

2200 152

1200 83

2200 152

3121125 – JLG Lift – 1-5

SECTION 1 - SPECIFICATIONS

Figure 1-1. Serial Number Locations

Table 1-18. Mobil EAL H Series Specs

Type Synthetic Biodegradable

ISO Viscosity Grade 32

Specific Gravity .950

Pour Point -59°F (-51°C)

Flash Point 514°F (268°C)

Weight

7.64 lb. per gal. (0.9 kg per liter)

Viscosity

at 40° C 33.1 cSt

at 100° C 6.36 cSt

Viscosity Index 147

1.15 SERIAL NUMBER LOCATIONS

For machine identification, a serial number plate is affixed to the left rear of frame, in front of left rear wheel. If the serial number plate is damaged or missing, the machine serial number is stamped on the top left side of the frame and the top left side of the turntable. In addition, the serial number is stamped on top of the end of the upper boom, mid boom, and lower boom at the left rear of the booms.

Lubrication Specifications

NOTE: Refer to Lubrication Chart, Figure1-2, for specific

lubrication procedures.

Table 1-17. Mobil DTE 11M Specs

ISO Viscosity Grade #15

Gravity API 31.9

Pour Point, Max -40 °F (-40°C)

Flash Point, Min. 330°F (166°C)

Viscosity

at 40° C 15 cSt

at 100° C 4.1 cSt

at 100° F 80 SUS

at 210° F 43 SUS

cp at -30° F 3.200

Viscosity Index 140

1.16 LUBRICATION

Table 1-16. Hydraulic Oil

Hydraulic System

Operating

Temperature Range

to + 180o F(-18o to +83o C)

+0o to + 210o F(-18o to +99o C)

+50o to + 210o F(+10o to +99o C)

NOTE: Hydraulic oils must have anti-wear qualities at least

to API Service Classification GL-3, and sufficient chemical stability for mobile hydraulic system ser-

1-6 – JLG Lift – 3121125

vice.

Aside from JLG recommendations, it is not advisable to mix oils of different brands or types, as they may not contain the same required additives or be of comparable viscosities. If use of hydraulic oil other than Mobil DTE 11M is desired, contact JLG Industries for proper recommendations.

S.A.E. Viscosity

Grade

10W

10W-20, 10W30

20W-20

SECTION 1 - SPECIFICATIONS

Figure 1-2. Operator Maintenance & Lubrication Diagram

3121125 – JLG Lift – 1-7

SECTION 1 - SPECIFICATIONS

Table 1-19. Lubrication Specifications.

KEY SPECIFICATIONS

MPG Multipurpose Grease having a minimum dripping poin t of 350

degrees F. Excellent water resistance and adhesive qualities; and being of extreme pressure type (Timken OK 40 poun ds minimum).

EPGL Extreme Pressure Gear Lube (oil) meeting API Service Classifi-

cation GL-5 or Mil-Spec Mil-L-2105.

HO Hydraulic Oil. Mobil DTE-11M

OG* Open Gear Lube - Tribol Molub-Alloy 936 Open Gear Com-

pound. (JLG Part No. 3020027)

BG* Bearing Grease (JLG Part No. 3020029) Mobilith SHA 460.

LL Synthetic Lithium L ubricant, Gredag 741 Grease. (JLG Part No.

3020022)

EO Engine (crankcase) Oil. Gas - API SF/SG class, MIL-L-2104.

D ie se l - AP I C C /C D c la ss , M I L-L- 21 04 B/ MI L-L- 2 10 4C .

*MPG may be substituted for these lubricants, if necessary, but service intervals will be reduced.

1.17 OPERATOR MAINTENANCE & LUBRICATION

NOTE: The following numbers correspond to those in Fig-

ure 1-2., Operator Maintenance & Lubrication Diagram.

2. Swing Bearing/Worm Gear Teeth

Lube Point(s) - 2 Grease Fittings Capacity - Spray On Lube - Mobiltac 375NC Interval - A/R Comments - If necessary install grease fittings into

worm gear housing and grease bearings.

DO NOT OVERGREASE BEARINGS. OVERGREASING BEARINGS WILL RESULT IN BLOWING OUTER SEAL IN HOUSING.

LUBRICATION INTERVALS ARE BASED ON MACHINE OPERATION UNDER NORMAL CONDITIONS. FOR MACHINES USED IN MULTISHIFT OPERATIONS AND/OR EXPOSED TO HOSTILE ENVIRONMENTS OR CONDITIONS, LUBRICATION FREQUENCIES MUST BE INCREASED ACCORDINGLY.

1. Swing Bearing

Lube Point(s) - 2 Grease Fittings Capacity - A/R Lube - MPG Interval - Every 3 months or 150 hrs of operation

1-8 – JLG Lift – 3121125

Comments - Remote Access

3. Hydraulic Tank

Lube Point(s) - Fill Cap Capacity - 4 Gal. (15.1 L) Lube - HO Interval - Check Level daily; Change every 2 years or

1200 hours of operation.

Comments - On new machines, those recently over-

hauled, or after changing hydraulic oil, operate all systems a minimum of two complete cycles and recheck oil level in reservoir.

SECTION 1 - SPECIFICATIONS

4. Hydraulic Return Filter

Interval - Change after first 50 hrs. and every 6

months or 300 hrs. thereafter.

Comments - Under certain conditions, it may be

necessary to replace the hydraulic filter on a more frequent basis. A common symptom of a dirty filter is sluggishness experienced in hydraulic functions.

5. Wheel Drive Hub

6. Wheel Bearings

Lube Point(s) - Repack Capacity - A/R Lube - MPG Interval - Every 2 years or 1200 hours of operation

7. Spindles/Bushing

Capacity - A/R Lube - Lithium Lubricant Interval - Every 2 years or 1200 hours of operation Comments - At Spindle/Bushing Replacement; Coat

I.D. of bushings prior to installing king pins.

8. Boom Pivot Pins/Bushing

Capacity - A/R Lube - Lithium Lubricant Interval - Every 2 years or 1200 hours of operation Comments - At boom pivot pins/bushing replace-

ment; Coat I.D. of bushings prior to installing pivot pins.

Lube Point(s) - Level/Fill Plug Capacity - 17 oz. (1/2 Full) Lube - EPGL Interval - Check level every 3 months or 150 hrs of

operation; change every 2 years or 1200 hours of operation

3121125 – JLG Lift – 1-9

SECTION 1 - SPECIFICATIONS

9. Engine

Lube Point(s) - Fill Cap Capacity - Refer to Engine Manual Lube - EO Interval - 3 Months or 150 hours of operation Comments - Check level daily/Change in accor-

dance with engine manual.

1-10 – JLG Lift – 3121125

SECTION 1 - SPECIFICATIONS

REFERENCE JLG ANEROBIC THREAD LOCKING COMPOUND

JLG P/N Loctite® P/N ND Industries P/N

Description

0100011

242

Vibra-TITE

121

Medium Strength (Blue)

0100019

271

Vibra-TITE

140

High Strength (Red)

0100071

262

Vibra-TITE

131

Medium - High Strength (Red)

Size TPI Bolt Dia

Tensile

Stress Area

Clamp Load

In Sq In LB IN-LB [N.m] IN-LB [N.m] IN-LB [N.m] IN-LB [N.m]

4 40 0.1120 0.00604 380 8 0.9 6 0.7

48 0.1120 0.00661 420 9 1.0 7 0.8

6 32 0.1380 0.00909 580 16 1.8 12 1.4

40 0.1380 0.01015 610 18 2.0 13 1.5

8 32 0.1640 0.01400 900 30 3.4 22 2.5

36 0.1640 0.01474 940 31 3.5 23 2.6

10 24 0.1900 0.01750 1120 43 4.8 32 3.5

32 0.1900 0.02000 1285 49 5.5 36 4

1/4 20 0.2500 0.0318 2020 96 10.8 75 9 105 12

28 0.2500 0.0364 2320 120 13.5 86 10 135 15

In Sq In LB FT-LB [N.m] FT-LB [N.m] FT-LB [N.m] FT-LB [N.m]

5/16 18 0.3125 0.0524 3340 17 23 13 18 19 26 16 22

24 0.3125 0.0580 3700 19 26 14 19 21 29 17 23

3/8 16 0.3750 0.0775 4940 30 41 23 31 35 48 28 38

24 0.3750 0.0878 5600 35 47 25 34 40 54 32 43

7/16 14 0.4375 0.1063 6800 50 68 35 47 55 75 45 61

20 0.4375 0.1187 7550 55 75 40 54 60 82 50 68

1/2 13 0.5000 0.1419 9050 75 102 55 75 85 116 68 92

20 0.5000 0.1599 10700 90 122 65 88 100 136 80 108

9/16 12 0.5625 0.1820 11600 110 149 80 108 120 163 98 133

18 0.5625 0.2030 12950 120 163 90 122 135 184 109 148

5/8 11 0.6250 0.2260 14400 150 203 110 149 165 224 135 183

18 0.6250 0.2560 16300 170 230 130 176 190 258 153 207

3/4 10 0.7500 0.3340 21300 260 353 200 271 285 388 240 325

16 0.7500 0.3730 23800 300 407 220 298 330 449 268 363

7/8 9 0.8750 0 .4620 29400 430 583 320 434 475 646 386 523

14 0.8750 0.5090 32400 470 637 350 475 520 707 425 576

1 8 1.0000 0.6060 38600 640 868 480 651 675 918 579 785

12 1.0000 0.6630 42200 700 949 530 719 735 1000 633 858

1 1/8 7 1.1250 0.7630 42300 800 1085 600 813 840 1142 714 968

12 1.1250 0.8560 47500 880 1193 660 895 925 1258 802 1087

1 1/4 7 1.2500 0.9690 53800 1120 1518 840 1139 1175 1598 1009 1368

12 1.2500 1.0730 59600 1240 1681 920 1247 1300 1768 1118 1516

1 3/8 6 1.3750 1.1550 64100 1460 1979 1100 1491 1525 2074 1322 1792

12 1.3750 1.3150 73000 1680 2278 1260 1708 1750 2380 1506 2042

1 1/2 6 1.5000 1.4050 78000 1940 2630 1460 1979 2025 2754 1755 2379

12 1.5000 1.5800 87700 2200 2983 1640 2224 2300 3128 1974 2676

NO. 5000059 REV. J

Values for Zinc Yellow Chromate Fasteners (Ref 4150707)

SAE GRADE 5 BOLTS & GRADE 2 NUTS

Torque

(Dry)

Torque

(Loctite® 262

or Vibra-

TITE

131)

Torque

Lubricated

Torque

(Loctite® 242

or 271

OR Vibra-TIT E

111 or

140)

3. * ASSEMBLY USES HARDENED WASHER

NOTES: 1. THESE TORQUE VALUES DO NOT APPLY TO CADMIUM PLATED FASTENERS

2. ALL TORQUE VALUES ARE STATIC TORQUE MEASURED PER STANDARD AUDIT METHODS TOLERANCE = ±10%

Figure 1-3. Torque Chart (SAE Fasteners - Sheet 1 of 7)

3121125 – JLG Lift – 1-11

SECTION 1 - SPECIFICATIONS

Size TPI Bolt Dia

Tensile

Stress Area

Clamp Load

In Sq In

4 40 0.1120 0.00604

48 0.1120 0.00661

6 32 0.1380 0.00909

40 0.1380 0.01015

8 32 0.1640 0.01400

36 0.1640 0.01474

10 24 0.1900 0.01750

32 0.1900 0.02000

1/4 20 0.2500 0.0318

28 0.2500 0.0364

In Sq In

5/16 18 0.3125 0.0524

24 0.3125 0.0580

3/8 16 0.3750 0.0775

24 0.3750 0.0878

7/16 14 0.4375 0.1063

20 0.4375 0.1187

1/2 13 0.5000 0.1419

20 0.5000 0.1599

9/16 12 0.5625 0.1820

18 0.5625 0.2030

5/8 11 0.6250 0.2260

18 0.6250 0.2560

3/4 10 0.7500 0.3340

16 0.7500 0.3730

7/8 9 0.8750 0.4620

14 0.8750 0.5090

1 8 1.0000 0.6060

12 1.0000 0.6630

1 1/8 7 1.1250 0.7630

12 1.1250 0.8560

1 1/4 7 1.2500 0.9690

12 1.2500 1.0730

1 3/8 6 1.3750 1.1550

12 1.3750 1.3150

1 1/2 6 1.5000 1.4050

12 1.5000 1.5800

NO. 5000059 REV. J

3. * ASSEMBLY USES HARDENED WASHER

NOTES: 1. THESE TORQUE VALUES DO NOT APPLY TO CADMIUM PLATED FASTENERS

2. ALL TORQUE VALUES ARE STATIC TORQUE MEASURED PER STANDARD AUDIT METHODS TOLERANCE = ±10%

LB IN-LB [N.m] IN-LB [N.m] IN-LB [N.m]

1320 43 5 1580 60 7 1800 68 8 2860 143 16 129 15 3280 164 19 148 17

LB FT-LB [N.m] FT-LB [N.m] FT-LB [N.m

4720 25 35 20 25 20 25 5220 25 35 25 35 20 25 7000456040 553550 7900 50 70 45 60 35 50 9550 70 95 65 90 50 70

10700 80 110 70 95 60 80 12750 105 145 95 130 80 110 14400 120 165 110 150 90 120 16400 155 210 140 190 115 155 18250 170 230 155 210 130 175 20350 210 285 190 260 160 220 23000 240 325 215 290 180 245 30100 375 510 340 460 280 380 33600 420 570 380 515 315 430 41600 605 825 545 740 455 620 45800 670 910 600 815 500 680 51500 860 1170 770 1045 645 875 59700 995 1355 895 1215 745 1015 68700 1290 1755 1160 1580 965 1310

77000 1445 1965 1300 1770 1085 1475 87200 1815 2470 1635 2225 1365 1855 96600 2015 2740 1810 2460 1510 2055

104000 2385 3245 2145 2915 1785 2430 118100 2705 3680 2435 3310 2030 2760 126500 3165 4305 2845 3870 2370 3225 142200 3555 4835 3200 4350 2665 3625

Torque

(Loctite® 242

or 271

OR Vibra-TITE

111 or

140) K=.18

Torque

(Loctite® 262

or Vibra-

TITE

131)

K=0.15

SAE GRADE 8 (HEX HD) BOLTS & GRADE 8 NUTS*

Torque

(Dry or Loctite® 263)

K= 0.20

1-12 – JLG Lift – 3121125

Figure 1-4. Torque Chart (SAE Fasteners - Sheet 2 of 7)

Size TPI Bolt Dia

Tensile

Stress Area

Clamp Load

See Note 4

In Sq In LB IN-LB [N.m] IN-LB [N.m] IN-LB [N.m]

4 40 0.1120 0.00604

48 0.1120 0.00661

6 32 0.1380 0.00909

40 0.1380 0.01015

8 32 0.1640 0.01400

36 0.1640 0.01474

10 24 0.1900 0.01750

32 0.1900 0.02000

1/4 20 0.2500 0.0318 2860 122 14 114 13

28 0.2500 0.0364 3280 139 16 131 15

In Sq In LB FT-LB [N.m] FT-LB [N.m] FT-LB [N.m]

5/16 18 0.3125 0.0524 4720 20 25 20 25 20 25

24 0.3125 0.0580 5220 25 35 20 25 20 25

3/8 16 0.3750 0.0775 7000 35 50 35 50 35 50

24 0.3750 0.0878 7900 40 55 40 55 35 50

7/16 14 0.4375 0.1063 9550 60 80 55 75 50 70

20 0.4375 0.1187 10700 65 90 60 80 60 80

1/2 13 0.5000 0.1419 12750 90 120 85 115 80 110

20 0.5000 0.1599 14400 100 135 95 130 90 120

9/16 12 0.5625 0.1820 16400 130 175 125 170 115 155

18 0.5625 0.2030 18250 145 195 135 185 130 175

5/8 11 0.6250 0.2260 20350 180 245 170 230 160 220

18 0.6250 0.2560 23000 205 280 190 260 180 245

3/4 10 0.7500 0.3340 30100 320 435 300 410 280 380

16 0.7500 0.3730 33600 355 485 335 455 315 430

7/8 9 0.8750 0.4620 41600 515 700 485 660 455 620

14 0.8750 0.5090 45800 570 775 535 730 500 680

1 8 1.0000 0.6060 51500 730 995 685 930 645 875

12 1.0000 0.6630 59700 845 1150 795 1080 745 1015

1 1/8 7 1.1250 0.7630 68700 1095 1490 1030 1400 965 1310

12 1.1250 0.8560 77000 1225 1665 1155 1570 1085 1475

1 1/4 7 1.2500 0.9690 87200 1545 2100 1455 1980 1365 1855

12 1.2500 1.0730 96600 1710 2325 1610 2190 1510 2055

1 3/8 6 1.3750 1.1550 104000 2025 2755 1905 2590 1785 2430

12 1.3750 1.3150 118100 2300 3130 2165 2945 2030 2760

1 1/2 6 1.5000 1.4050 126500 2690 3660 2530 3440 2370 3225

12 1.5000 1.5800 142200 3020 4105 2845 3870 2665 3625

NO. 5000059 REV. J

4. CLAMP LOAD LISTED FOR SHCS IS SAME AS GRADE 8 OR CLASS 10.9 AND DOES NOT REPRESENT FULL STRENGTH

CAPABILITY OF SHCS. IF HIGHER LOAD IS REQUIRED, ADDITIONAL TESTING IS REQUIRED.

SOCKET HEAD CAP SCREWS

Magni Coating (Ref 4150701)*

Torque

(Dry) K = .17

Torque

(Loctite® 242

or 271

OR Vibra-TITE

111 or

140 OR Precoat 85®

K=0.16

Torque

(Loctite® 262

or Vibra-

TITE

131)

K=0.15

2. ALL TORQUE VALUES ARE STATIC TORQUE MEASURED PER STANDARD AUDIT METHODS TOLERANCE = ±10%

NOTES: 1. THESE TORQUE VALUES DO NOT APPLY TO CADMIUM PLATED FASTENERS

*3. ASSEMBLY USES HARDENED WASHER OR FASTENER IS PLACED AGAINST PLATED STEEL OR RAW ALUMINUM

SECTION 1 - SPECIFICATIONS

3121125 – JLG Lift – 1-13

Figure 1-5. Torque Chart (SAE Fasteners - Sheet 3 of 7)

SECTION 1 - SPECIFICATIONS

Size TPI Bolt Dia

Tensile

Stress Area

Clamp Load

See Note 4

In Sq In LB IN-LB [N.m] IN-LB [N.m] IN-LB [N.m]

4 40 0.1120 0.00604

48 0.1120 0.00661

6 32 0.1380 0.00909

40 0.1380 0.01015

8 32 0.1640 0.01400

36 0.1640 0.01474

10 24 0.1900 0.01750

32 0.1900 0.02000

1/4 20 0.2500 0.0318 2860 143 16 129 15

28 0.2500 0.0364 3280 164 19 148 17

In Sq In LB FT-LB [N.m] FT-LB [N.m] FT-LB [N.m]

5/16 18 0.3125 0.0524 4720 25 35 20 25 20 25

24 0.3125 0.0580 5220 25 35 25 35 20 25

3/8 16 0.3750 0.0775 7000 45 60 40 55 35 50

24 0.3750 0.0878 7900 50 70 45 60 35 50

7/16 14 0.4375 0.1063 9550 70 95 65 90 50 70

20 0.4375 0.1187 10700 80 110 70 95 60 80

1/2 13 0.5000 0.1419 12750 105 145 95 130 80 110

20 0.5000 0.1599 14400 120 165 110 150 90 120

9/16 12 0.5625 0.1820 16400 155 210 140 190 115 155

18 0.5625 0.2030 18250 170 230 155 210 130 175

5/8 11 0.6250 0.2260 20350 210 285 190 260 160 220

18 0.6250 0.2560 23000 240 325 215 290 180 245

3/4 10 0.7500 0.3340 30100 375 510 340 460 280 380

16 0.7500 0.3730 33600 420 570 380 515 315 430

7/8 9 0.8750 0.4620 41600 605 825 545 740 455 620

14 0.8750 0.5090 45800 670 910 600 815 500 680

1 8 1.0000 0.6060 51500 860 1170 775 1055 645 875

12 1.0000 0.6630 59700 995 1355 895 1215 745 1015

1 1/8 7 1.1250 0.7630 68700 1290 1755 1160 1580 965 1310

12 1.1250 0.8560 77000 1445 1965 1300 1770 1085 1475

1 1/4 7 1.2500 0.9690 87200 1815 2470 1635 2225 1365 1855

12 1.2500 1.0730 96600 2015 2740 1810 2460 1510 2055

1 3/8 6 1.3750 1.1550 104000 2385 3245 2145 2915 1785 2430

12 1.3750 1.3150 118100 2705 3680 2435 3310 2030 2760

1 1/2 6 1.5000 1.4050 126500 3165 4305 2845 3870 2370 3225

12 1.5000 1.5800 142200 3555 4835 3200 4350 2665 3625

NO. 5000059 REV. J

4. CLAMP LOAD LISTED FOR SHCS IS SAME AS GRADE 8 OR CLASS 10.9 AND DOES NOT REPRESENT FULL STRENGTH

CAPABILITY OF SHCS. IF HIGHER LOAD IS REQUIRED, ADDITIONAL TESTING IS REQUIRED.

SOCKET HEAD CAP SCREWS

Torque

(Dry)

K = .20

Torque

(Loctite® 242TM or 271

OR Vibra-TITE

111 or

140 OR Precoat 85®

K=0.18

Zinc Yellow Chromate Fasteners (Ref 4150707)*

2. ALL TORQUE VALUES ARE STATIC TORQUE MEASURED PER STANDARD AUDIT METHODS TOLERANCE = ±10%

NOTES: 1. THESE TORQUE VALUES DO NOT APPLY TO CADMIUM PLATED FASTENERS

*3. ASSEMBLY USES HARDENED WASHER OR FASTENER IS PLACED AGAINST PLATED STEEL OR RAW ALUMINUM

Torque

(Loctite® 262

or Vibra-

TITE

131)

K=0.15

1-14 – JLG Lift – 3121125

Figure 1-6. Torque Chart (SAE Fasteners - Sheet 4 of 7)

SECTION 1 - SPECIFICATIONS

Size PITCH

Tensile

Stress

Area

Clamp

Load

Torque

(Dry or Loctite®

263

)

Torque

(Lub)

Torque

(Loctite® 262

OR Vibra-

TITE

131)

Torque

(Loctite®

242

or 271

OR Vibra-

TITE

111 or

140)

Sq mm K N [N.m] [N.m] [N.m] [N. m]

3 0.5 5.03 2.19 1.3 1.0 1.2 1.4

3.5 0.6 6.78 2.95 2.1 1.6 1.9 2.3 4 0.7 8.78 3.82 3.1 2.3 2.8 3.4 5 0.8 14.20 6.18 6.2 4.6 5.6 6.8 6 1 20.10 8.74 11 7.9 9.4 12 7 1 28.90 12.6 18 13 16 19 8 1.25 36.60 15.9 26 19 23 28

10 1.5 58.00 25.2 50 38 45 55 12 1.75 84.30 36.7 88 66 79 97 14 2 115 50.0 140 105 126 154

16 2 157 68.3

219 164 197 241 18 2.5 192 83.5 301 226 271 331 20 2.5 245 106.5 426 320 383 469 22 2.5 303 132.0 581 436 523 639 24 3 353 153.5 737 553 663 811 27 3 459 199.5 1080 810 970 1130 30 3.5 561 244.0 1460 1100 1320 1530 33 3.5 694 302.0 1990 1490 1790 2090 36 4 817 355.5 2560 1920 2300 2690 42 4.5 1120 487.0 4090 3070 3680 4290

4. CLAMP LOAD LISTED FOR SHCS IS SAME AS GRADE 8 OR CLASS 10.9 AND DOES NOT REPRESENT FULL STRENGTH CAPABILITY OF SHCS. IF HIGHER LOAD IS REQUIRED, ADDITIONAL TESTING IS REQUIRED.

*3. ASSEMBLY USES HARDENED WASHER OR FASTENER IS PLACED AGAINST PLATED STEEL OR RAW ALUMINUM

CLASS 8.8 METRIC BOLTS

CLASS 8 METRIC NUTS

NOTES: 1. THESE TORQUE VALUES DO NOT APPLY TO CADMIUM PLATED FASTENERS

2. ALL TORQUE VALUES ARE STATIC TORQUE MEASURED PER STANDARD AUDIT METHODS TOLERANCE = ±10%

NO. 5000059 REV. J

Figure 1-7. Torque Chart (METRIC Fasteners - Sheet 5 of 7)

3121125 – JLG Lift – 1-15

SECTION 1 - SPECIFICATIONS

Size PITCH

Tensile

Stress

Area

Clamp

Load

Torque

(Dry or Loctite®

263

)

K = 0.20

Torque

(Lub OR Loctite®

242

or 271TM OR

Vibra-TITE

111 or

140)

K= 0.18

Torque

(Loctite® 262

Vibra-TITE

131)

K=0.15

Sq mm KN [N.m] [N.m] [N.m]

3 0.5 5.03 3.13

3.5 0.6 6.78 4.22

4 0.7 8.78 5.47 5 0.8 14.20 8.85 6 1 20.10 12.5 7 1 28.90 18.0 25.2 22.7 18.9

8 1.25 36.60 22.8 36.5 32.8 27.4 10 1.5 58.00 36.1 70 65 55 12 1.75 84.30 52.5 125 115 95 14 2 115 71.6 200 180 150

16 2 157 97.8

315 280 235 18 2.5 192 119.5 430 385 325 20 2.5 245 152.5 610 550 460 22 2.5 303 189.0 830 750 625 24 3 353 222.0 1065 960 800 27 3 459 286.0 1545 1390 1160 30 3.5 561 349.5 2095 1885 1575 33 3.5 694 432.5 2855 2570 2140 36 4 817 509.0 3665 3300 2750 42 4.5 1120 698.0 5865 5275 4395

CLASS 10.9 METRIC BOLTS

CLASS 10 METRIC NUTS

CLASS 12.9 SOCKET HEAD CAP SCREWS M3 - M5*

4. CLAMP LOAD LISTED FOR SHCS IS SAME AS GRADE 8 OR CLASS 10.9 A ND DOES NOT

REPRESENT FULL STRENGTH CAPABILITY OF SHCS. IF HIGHER LOAD IS REQUIRED,

ADDITIONAL TESTING IS REQUIRED.

*3. ASSEMBLY USES HARDENED WASHER OR FASTENER IS PLACED AGAINST PLATED STEEL OR RAW ALUMINUM

NOTES: 1. THESE TORQUE VALUES DO NOT APPLY TO CADMIUM PLATED FASTENERS

2. ALL TORQUE VALUES ARE STATIC TORQUE MEASURED PER STANDARD AUDIT METHODS TOLERANCE = ±10%

NO. 5000059 REV. J

Figure 1-8. Torque Chart (METRIC Fasteners - Sheet 6 of 7)

1-16 – JLG Lift – 3121125

+ 226 hidden pages