Page 1
800 Series
Owner’s Guide
Page 2
Important Safety Instructions
WARNING: TO REDUCE THE RISK OF INJURY OR DAMAGE, READ THE FOLLOWING SAFETY
PRECAUTIONS WHEN SETTING UP, USING AND MAINTAINING YOUR ROBOT.
THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS
WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND
KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF
THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED. CHILDREN SHALL
NOT PLAY WITH THE APPLIANCE. CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY
CHILDREN WITHOUT SUPERVISION.
WARNING: TO AVOID ELECTRIC SHOCK DO NOT EXPOSE THE ELECTRONICS OF YOUR
ROBOT, OR THE INTEGRATED DOCK-CHARGER KNOWN AS HOME BASE. THERE ARE NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DO NOT HANDLE YOUR ROBOT AND HOME BASE™ WITH WET HANDS.
EN
Roomba® 800 Series Owner’s Guide i
Page 3
EN
Important Safety Instruction (cont.)
• Heed all warnings on your robot, and it’s parts.
• WARNING: Risk of electric shock, use indoors in dry location only.
• Your robot is not a toy. Do not sit or stand on this device. Small children and pets should
be supervised when your robot is operating.
• Store and operate your robot in room temperature environments only.
• Do not use this device to pick up sharp objects, glass, or anything that is burning or smoking.
• Do not use this device to pick up spills of water bleach, paint, or other chemicals,
or anything wet.
• Do not spray or pour liquids on your robot.
• Before using this device, pick up objects like clothing, loose papers, pull cords for blinds or
curtains, power cords, and any fragile objects. If the device passes over a power cord and
drags it, there is a chance an object could be pulled o a table or shelf.
• If the room to be cleaned contains a balcony, a physical barrier should be used to prevent
access to the balcony and ensure safe operation.
• Do not place anything on top of your robot.
• Be aware that the robot moves on its own. Take care when walking in the area that the robot
is operating in to avoid stepping on it.
• Do not operate the robot in areas with exposed electrical outlets in the floor.
• WARNING Shock Hazard: Your robot comes with a region approved power
supplycord. Do not use any other power supply cord. For replacement cords, please
contact Customer Care to ensure proper selection of country specific power supply cord.
• This robot is intended for dry floor use only.
• WARNING Shock and Fire Hazard: This product is designed to be plugged
into a standard outlet only. Product may not be used with any type of power converter.
Use of power converters will immediately void the warranty.
• Do not use non-rechargeable batteries. Use only the rechargeable battery supplied
with the product. For replacement, purchase identical iRobot battery or contact
iRobot Customer Care for alternative battery options.
• CAUTION: Only charge one of the following iRobot batteries: maximum 14.8V, max
3000mAh Ni-MH or maximum 3300mAh Li-ion battery. Other type of batteries may burst
causing injury. Always contact Customer Care for the correct replacement of your battery.
• WARNING Shock Hazard: Do not use a Home Base with a damaged cord or plug
if the cord or plug is damaged, it must be replaced.
• Always charge and remove the battery from your robot and accessories before
long-term storage or transportation.
• If you live in an area prone to electrical storms, it is recommended that you use
additional surge protection. Your robot’s Home Base may be protected with a surge
protector in the event of severe electrical storms.
• WARNING Shock Hazard: Always disconnect your robot from the Home Base
before cleaning or maintaining it.
• Before every use, check the battery pack for any sign of damage or leakage. Do not
charge damaged or leaking battery packs.
• WARNING Chemical Exposure: If the battery pack is leaking, do not allow the liquid
to come in contact with skin or eyes. If contact has been made, wash the aected area
with copious amounts of water and seek medical advice. Place the battery in a sealed
plastic bag and dispose of safely according to local environmental regulations. return
it to your local authorized iRobot Service Center for disposal.
• The battery pack must be removed from the robot before disposal.
• WARNING Fire or Explosion Hazard: Do not crush or dismantle battery packs.
Do not heat or place the battery pack near any heat sourceor direct sunlight. Do not
incinerate or short-circuit the battery pack. Do not subject batteries to mechanical shock.
• Do not immerse the battery pack in any liquid.
• Contact your local waste management authority for battery recycling and disposal
regulations in your area.
The symbol on the product or its packaging indicates:
Do not dispose of electrical appliances or batteries as unsorted municipal waste,
use separate collection facilities. Contact your local authority for information regarding
the collection systems available. If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the groundwater and get into the food
chain, damaging your health and well-being. Please contact your local or regional
waste authority for more information on collection, reuse and recycling programs.
ii For more information, visit www.irobot.com/Roomba800
Page 4
Table of Contents
Important Safety Instructions ................................................................................................i
About Your Roomba® ........................................................................................................... 2
Using Your Roomba® ............................................................................................................. 3
Scheduling ............................................................................................................................. 4
Accessories ............................................................................................................................ 5
Regular Robot Care ............................................................................................................. 6
Troubleshooting .................................................................................................................. 10
iRobot Customer Care ....................................................................................................... 11
EN
Roomba® 800 Series Owner’s Guide 1
Page 5
About your Roomba
EN
Top View
Faceplate
Bin Release
Button
Dust Bin
andFilter
Bottom View
Extractor Caps
Dust Bin and Filter
Cli Sensor
Cli Sensor
RCON Sensor
Handle
Light Touch Sensor
Debris Extractors
Extractor Frame
Release Tabs
Cli Sensor
Side Brush
Charging
Contacts
Cli Sensor
Caster Wheel
Cli Sensor
Home Base
RCON
Sensor
Charging
Contacts
Buttons & Indicators
Battery Indicator
Dirt Detect™ Indicator
CLEAN/Power Button
DAY
DOCK
HOUR
CLOCK
Anti-Tangle
Indicator
Troubleshooting
Indicator
OK
SPOT
MINUTE
SCHEDULE
Full Bin Indicator
2 For more information, visit www.irobot.com/Roomba800
Page 6
Using your Roomba
Positioning the Home Base
Place the Home Base in an open, uncluttered area
leaving the following distances around the Home Base:
• At least 1.5 feet (0.5 meters) on each side of the
Home Base
• At least 4 feet (1.2 meters) in front of the Home
Base, and at least 4 feet (1.2 meters) away from stairs
• At least 8 feet (2.4 meters) from Virtual Wall Barriers
Always keep the Home Base plugged in.
®
Use Instructions
• Turn your robot over and remove the bin insert and battery pull
tabs. Then place Roomba on the Home Base to charge.
• Fully charge the battery before the first cleaning by allowing
Roomba to charge on the Home Base for 3 hours.
• Manually wake Roomba up by pressing CLEAN once.
To start a cleaning cycle, press CLEAN again.
Note: Remove excess clutter from floors before cleaning
(e.g. clothing, toys, etc.). Use Roomba frequently
to maintain well-conditioned floors.
• To pause Roomba during a cleaning cycle, press CLEAN. To
resume the cleaning cycle, press CLEAN again.
• To end the cleaning cycle and put Roomba in standby mode,
press and hold CLEAN until Roomba’s indicators turn o.
• If Roomba encounters an area of high debris concentration, it
will move in a forward/backward motion to clean the area more
thoroughly. When Roomba does this, you will see the Dirt Detect™
Indicator ( ) illuminate.
• To send Roomba back to its Home Base during a cleaning cycle, press
(DOCK) on Roomba. This will end the cleaning cycle.
• To use (SPOT) Cleaning, place Roomba on top of the
localized debris and press (SPOT) on the robot. Roomba will thoroughly
clean the area by spiraling outward about 3 feet (1meter) in diameter
and then spiraling inward to where it started.
• When Roomba returns to the Home Base after completing a cleaning
cycle, it will play a series of tones to indicate successful completion of the
cleaning cycle.
Note: After each use, empty the bin and clean the filter.
• Always store Roomba on the Home Base so it’s charged and ready to
clean when you need it. If storing o of the Home Base, remove the
battery first and then store Roomba and the battery in a cool, dry place.
Battery and Charging
Charge Roomba using the Home Base. Indicator lights will turn o after 60
seconds to conserve energy while Roomba is charging. Check status of the
battery by pressing the CLEAN button to illuminate the Battery Indicator.
Indicator will appear amber while the battery is charging and solid green
when fully charged.
Setting the Clock
You must set the clock before scheduling Roomba to clean. To set the time:
Press
1
2
Use the Day, Hour, and Minute buttons to set the correct time.
3
Press OK. Roomba will beep to indicate the time and date has been set.
CLOCK
.
EN
Roomba® 800 Series Owner’s Guide 3
Page 7
EN
Scheduling
You can schedule Roomba to clean once per day, up to seven times per
week. You must set the time before setting a schedule.
To Set or Change the Cleaning Schedule
Wake up Roomba by pressing the CLEAN button.
1
2
Press
SCHEDULE.
3
Use Hour and MINUTE buttons individually to set the schedule.
Press OK, Roomba will beep to indicate the schedule has been set.
4
To Delete a Scheduled Cleaning Time
Wake up Roomba by pressing the CLEAN button.
1
Press SCHEDULE.
2
3
Press DAY to cycle through the schedule cleaning times.
When Roomba displays the scheduled cleaning time you’d like to
4
delete, press and hold DAY for five seconds. Roomba will beep to
indicate the cleaning time has been deleted.
Press OK.
5
4 For more information, visit www.irobot.com/Roomba800
Page 8
Accessories
The Dual Mode Virtual Wall Barrier
(accessory compatible with all models)
The Dual Mode Virtual Wall barrier keeps
Roomba in the places you want to be
cleaned — and out of the ones you don’t.
Inbetween cleaning cycles, you can leave
the device operating in its position on the
floor. You can set your device to one of two
modes to fit your home’s cleaning needs:
Note: Under normal use, batteries will last 8-10 months. If you are not
planning on using your Virtual Wall device for an extended period of time
and you would like to store it, be sure to switch it to the “O ” (middle) position.
Virtual Wall Mode: When the switch is
in the “up” position ( ), the device
functions as a Virtual Wall. This means
that you can set it to block openings of
up to 10 feet (3 meters). It creates an
invisible, cone-shaped barrier that only
Roomba can see.
Note: This barrier gets wider as it gets
further from the device (refer to illustration).
Halo Mode: When the switch is in the
“down” position ( ), the device creates
a protective zone that Roomba will
not enter. This prevents Roomba from
bumping into items you want to protect
(e.g. a dog bowl or vase) or crossing into
undesired areas (e.g. a corner or under
a desk). The Halo is invisible and reaches
approximately 24 inches (60 centimeters)
from the center of the device.
10ft / 3m
4ft / 1.2m
The Virtual Wall Lighthouse
(accessory compatible with select models)
The Virtual Wall Lighthouse can act as both a
Lighthouse and a Virtual Wall. Simply use the Mode
Selector to make your choice. The device turns on
and o automatically as you turn Roomba on and o.
When on, the light on top is lit. A slowly blinking power
light means the batteries need replacing soon:
Virtual Wall Mode: When the switch is in the “Virtual Wall” position, the
device functions as a Virtual Wall. This means that you can set it to block
openings of up to 8 feet (2.4 meters). It creates an invisible, coneshaped barrier that only Roomba can see.
Note: This barrier gets wider
as it gets further from the device
(refer to illustration).
Lighthouse Mode: When switch
is in “Lighthouse” mode, the device
allows Roomba to eciently clean
multiple rooms before returning
to Home Base. Place a Lighthouse
in the doorway with logo facing
forward, when Roomba has
completed the first room, the
Lighthouse will help it navigate to
the next.
You can use Lighthouse devices and
Virtual Wall barriers at the same
time. However, please avoid placing
them too close to each other, to
the Home Base, or to furniture that
could block the invisible beams.
10ft / 3m
EN
Roomba® 800 Series Owner’s Guide 5
Page 9
EN
Regular Robot Care
Recommended Robot Care
To keep Roomba running at peak performance, perform the following care
procedures. If you notice Roomba picking up less debris from your floor, empty
the bin, clean the filter and clean the extractors.
Robot Part Care Frequency Replacement
Frequency
Bin After each use -
Filter Once per week
Full Bin Sensors
Front Caster Wheel
Side Brush
Cli Sensors
Charging Contacts
(twice per week in
homes with pets)
Once every 2 weeks Every 12 months
Once per month
Every 2 months
-
6 For more information, visit www.irobot.com/Roomba800
Extractors Once every 4 months
(once every 3 months
in homes with pets)
Note: iRobot manufactures various replacement parts and assemblies.
Purchase replacement parts by visiting www.irobot.com/Roomba800. If
you have questions regarding replacement parts, please contact iRobot
Customer Care for more information.
Every 6-12 months
Page 10
Emptying the bin
Cleaning the Filter
Cleaning the Full Bin Sensors
Press bin release
1
button to remove bin.
Open bin door to
2
empty bin.
Open the filter door and
1 1
remove filter by grasping
the tab.
2 2
Shake o debris by
tapping the filter against
your trash container.
3
Reinsert filter with the tab
facing up.
Important: The filter door won’t
close unless a filter is reinserted
correctly. Replace the filter every
two months.
Remove and empty the bin.
Wipe the sensors with a clean, dry cloth.
3
Wipe the inner and outer sensor ports
on the bin with a clean, dry cloth.
Outer Sensor Ports
Inner Sensor Ports
EN
Roomba® 800 Series Owner’s Guide 7
Page 11
Cleaning the Front Caster Wheel
Cleaning the Side Brush
EN
Pull firmly on the front wheel to remove it.
1 1
Remove any debris from inside the wheel cavity.
2
Spin the wheel by hand. If the rotation is restricted, remove the
3
wheel from its housing and push firmly to remove the axle and
clear any debris or hair wrapped around it.
Reinstall all parts when finished. Make sure the wheel clicks back
4
into place.
Wheel
Axle
Housing
Important: A front wheel clogged with hair and debris
could result in floor damage.
Use a coin or small screwdriver to remove the screw.
Remove the brush, clean the brush and the brush post, and then
2
reinstall the brush.
8 For more information, visit www.irobot.com/Roomba800
Page 12
Cleaning the Sensors and
Charging Contacts
Cleaning the Extractors
Wipe the sensors with a clean, dry cloth.
1
Do not spray cleaning solution directly
onto the sensors or sensor openings. Wipe
the charging contacts on Roomba and the
Home Base with a clean, dry cloth.
Pinch the extractor frame
1
release tabs, lift up the
extractor frame and remove
any obstructions.
Remove the extractors and
2
remove the extractor caps.
Remove any hair or debris that
has collected underneath the
caps and around the metal axles.
Reinstall the extractor caps.
Remove hair and debris from the
3
square and hexagonal plastic
pegs on the other side of the
extractors.
Clear the vacuum path.
4
Reinstall the extractors. Match the
5
color and shape of the extractor
pegs with the color and shape of
the extractor icons on the cleaning
head module.
EN
Roomba® 800 Series Owner’s Guide 9
Page 13
Troubleshooting
EN
Roomba will tell you something is wrong with a two-tone distress sound followed
by a spoken message. The troubleshooting indicator ( ) will also blink. Follow
the audible instructions. Additional troubleshooting information, along with more
detailed support and videos, are available online at www.irobot.com/Roomba800.
To reboot Roomba, press and hold CLEAN for 10 seconds until all indicators
illuminate, then release. When you release the CLEAN button, you will hear an
audible tone signifying a successful reboot. This will clear all scheduled cleaning
times, reset the clock and resolve some software issues.
If you have questions or comments about this product, please contact iRobot
before contacting a retailer.
Visit the iRobot Owner’s Center at www.iRobot.com/Roomba800 for for support
tips, frequently asked questions, and information about accessories and other
iRobot products.
Lithium Ion Battery (select models only)
For best results, only use the iRobot Lithium Ion Battery that comes with Roomba.
While Roomba will operate with older-model batteries, its performance will
be limited.
Important: Lithium ion batteries and products that contain lithium ion
batteries are subject to stringent transportation regulations. If you need to
ship this product (with the battery included) for service, travel or any other
reason, you MUST comply with the following shipping instructions:
» Remove the lithium ion battery from the product
» Please visit www.iRobot.com/Roomba800 to view an instructional video on
how to remove the battery
» Place a piece of tape over the battery’s metal charging contacts
» Reinstall the battery (with the tape on it) in the product and secure the
battery door
» Package the product in its original packaging or in your own packaging that
prevents any movement during transportation
» Ship via ground transportation only (no air shipping)
10 For more information, visit www.irobot.com/Roomba800
Page 14
iRobot Customer Care
USA & Canada
If you have questions or comments about
your Roomba, please contact iRobot before
contacting a retailer.
You can start by visiting
www.irobot.com/Roomba800 for support tips,
frequently asked questions and information
about accessories. Should you still need
assistance, call our Customer Care team at
(877) 855-8593.
iRobot Customer Care Hours:
• Monday to Friday, 9AM – 9PM Eastern Time
• Saturday and Sunday 9AM – 6PM Eastern Time
Outside USA & Canada
Visit global.irobot.com to:
• Learn more about iRobot in your country.
• Get hints and tips to improve your Roomba’s
performance.
• Get answers to questions.
• Contact your local support center.
For EU Declaration of Conformity information,
visit www.irobot.com/compliance.
EN
Roomba® 800 Series Owner’s Guide 11
Page 15
© iRobot Corporation, Crosby Drive, Bedford, MA USA. All rights reserved.
iRobot, Roomba, iAdapt, Home Base and Virtual Wall are registered trademarks of
iRobotCorporation. AeroVac and Dirt Detect are trademarks of iRobot Corporation.
Loading...