Integra DTR-50.3 Owner's Manual

Download

Page 1

AV Receiver

DTR-50.3

Instruction Manual

Page 2

Introduction

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PORTABLE CART WARNIN

S3125A

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into

the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

Page 3

Precautions

1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit.

3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

For models with [Power] button, or with both [Power] and [On/Standby] buttons: Pressing the [Power] button to select OFF mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

For models with [On/Standby] button only: Pressing the [On/Standby] button to select Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure Warning

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by the dealer from whom you purchased this unit.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for

a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after prolonged use. This is normal.

• If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer from whom you purchased this unit or an experienced radio/TV technician for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Page 4

Thank you for purchasing an Integra AV receiver. Please read this manual thoroughly before making

connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment

from your new AV receiver. Please retain this manual for future reference.

Supplied Accessories

Make sure you have the following accessories:

Indoor FM antenna (➔ page 21)

AM loop antenna (➔ page 21)

Power cord (➔ page 21)

Speaker cable labels (➔ page 13)

Speaker setup microphone (➔ page 31)

Remote controller (RC-811M) and two batteries (AA/R6)

In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

■ Installing the batteries

Note

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

Batteries (AA/R6)

■ Aiming the remote controller

To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.

Transmission

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

Reception

Transmitter

AV receiver

Input sensor

Approx. 16 ft. (5 m)

Page 5

Contents

Introduction

Important Safety Instructions ......................................... 2

Precautions....................................................................... 3

Supplied Accessories...................................................... 4

Features ............................................................................ 6

Front & Rear Panels......................................................... 8

Front Panel..................................................................... 8

Display............................................................................ 9

Rear Panel ................................................................... 10

Remote Controller.......................................................... 11

Controlling the AV Receiver ......................................... 11

Connections

Connecting the AV Receiver ......................................... 12

Connecting Your Speakers .......................................... 12

About AV Connections ................................................. 16

Connecting Components with HDMI ............................ 17

Connecting Your Components ..................................... 18

Connecting Integra/Onkyo u Components ................ 20

Connecting a Recording Component ........................... 20

Connecting the Antennas ............................................. 21

Connecting the Power Cord ......................................... 21

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................... 22

Turning On ................................................................... 22

Turning Off ................................................................... 22

Playback.......................................................................... 23

Selecting the Language for the Onscreen

Setup Menus.............................................................. 23

Playing the Connected Component.............................. 23

Controlling Contents of USB or Network Devices ........ 23

Understanding Icons on the Display............................. 24

Playing an iPod/iPhone via USB .................................. 24

Playing a USB Device .................................................. 25

Listening to Internet Radio ........................................... 25

Playing Music Files on a Server ................................... 27

Remote Playback ......................................................... 27

Listening to AM/FM Radio ............................................ 28

Using Basic Functions .................................................. 31

Using the Automatic Speaker Setup ............................ 31

Using the Listening Modes ........................................... 34

Using the Home Menu.................................................. 40

Using the Sleep Timer.................................................. 40

Setting the Display Brightness ..................................... 40

Displaying Source Information ..................................... 41

Changing the Input Display .......................................... 41

Selecting Speaker Layout ............................................ 41

Muting the AV Receiver................................................ 41

Using Headphones....................................................... 41

Using Easy Macros ...................................................... 42

Recording ..................................................................... 42

Advanced Operations

Advanced Setup .............................................................43

On-screen Setup Menus............................................... 43

Common Procedures in Setup Menu ........................... 43

Input/Output Assign ......................................................44

Speaker Setup.............................................................. 47

Audio Adjust .................................................................50

Source Setup................................................................ 52

Listening Mode Preset.................................................. 58

Miscellaneous............................................................... 58

Hardware Setup............................................................ 59

Remote Controller Setup .............................................. 63

Lock Setup.................................................................... 63

Using the Audio Settings ..............................................63

Multi Zone ....................................................................... 66

Making Multi Zone Connections ...................................66

Controlling Zone 2/3 Components................................ 67

Using the 12V Triggers................................................. 68

Using the Remote Controller in

Zone and Multiroom Control Kits ............................... 69

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock ........................70

Using the Onkyo Dock.................................................. 70

Controlling Your iPod/iPhone .......................................71

Controlling Other Components..................................... 73

Preprogrammed Remote Control Codes ...................... 73

Looking up for Remote Control Code ........................... 73

Entering Remote Control Codes................................... 74

Remote Control Codes for

Integra/Onkyo Components Connected via u ......... 75

Resetting Remote Mode Buttons.................................. 75

Resetting the Remote Controller ..................................75

Controlling Other Components .....................................75

Learning Commands ....................................................77

Using Normal Macros ................................................... 78

Appendix

Troubleshooting .............................................................79

Firmware Update ............................................................85

Connection Tips and Video Signal Path ...................... 88

Using an RIHD-compatible TV, Player, or Recorder ... 91

About HDMI..................................................................... 93

Network/USB Features...................................................94

Specifications .................................................................97

To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press

8On/Standby (➔ page 79).

Page 6

Features

Amplifier

• 135 Watts/Channel @ 8 ohms (FTC)

• 180 Watts/Channel @ 6 ohms (IEC)

• 230 Watts/Channel @ 6 ohms (JEITA)

• WRAT–Wide Range Amplifier Technology (5 Hz to 100 kHz bandwidth)

• Linear Optimum Gain Volume Circuitry

• 3-Step Inverted Darlington Circuitry

• H.C.P.S. (High Current Power Supply) Massive High Power Transformer

Processing

• THX Select2 Plus*1 Certified

• Incorporates Qdeo™ Upscaling (to 4K Compatible)

•HQV

-Vida Video Processing with 1080p Video

upscaling of All Video Sources via HDMI

• HDMI (Audio Return Channel, 3D, DeepColor, x.v.Color*4, Lip Sync, DTS-HD Master Audio*5, DTS-HD High Resolution Audio, Dolby TrueHD*6, Dolby Digital Plus, DSD and Multi-CH PCM)

• Dolby TrueHD*6 and DTS-HD Master Audio

• Dolby Pro Logic IIz*6 and Audyssey DSX™

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• Direct Mode

• Music Optimizer

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

• Jitter Cleaning Circuit Technology

technology for HDMI Video

for Compressed Digital Music files

Connections

•8HDMI*9 Inputs (1 on front panel) and 2 Outputs

• Integra/Onkyo p for System Control

• 6 Digital Inputs (3 Optical/3 Coaxial)

• Component Video Switching (3 Inputs/2 Output)

• Universal Port for the Dock for iPod HD Radio™

*11

tuner module (North American

/iPhone

*10

models)/DAB+ tuner module (Australian models)

• Banana Plug-Compatible Speaker Posts

• Powered Zone 2 and Zone 2/3 Pre Out

• IR Input/Output and 12 V Trigger

• RS232 Port for Interface Control

• Bi-Amping Capability for FL/FR with SBL/SBR

• Analog RGB Video Input (D-sub 15) for PC

• Internet Radio Connectivity (SiriusXM Internet Radio/vTuner/Last.fm/Pandora/Rhapsody/Slacker/ Mediafly/Napster)

Services available may vary depending on the region.

• Network Capability for Streaming Audio Files

*12

• 2 USB Inputs* (Front/Rear) for Memory Devices and

iPod®/iPhone

*10

models (Enables Display of Album

Artwork)

Only front-panel USB input is compatible with iPod/iPhone.

Miscellaneous

• 40 AM/FM Presets

•Dolby Volume

• Audyssey MultEQ®XT*7 to correct room acoustic problems

• Audyssey Dynamic EQ

• Audyssey Dynamic Volume listening level and dynamic range

• Crossover Adjustment (40/45/50/55/60/70/80/90/100/110/120/130/150/200 Hz)

• A/V Sync Control Function (up to 800 ms)

• Auto Standby Function

• Bi-Directional Preprogrammed (with onscreen display setup) RI-Compatible Learning Remote with 4 Activities and Mode-Key LEDs

• ISF (Imaging Science Foundation) Video Calibration

for loudness correction

to maintain optimal

Page 7

THX Select2 Plus

Before any home theater component can be THX Select2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Select2 Plus logo, which is your guarantee that the Home Theater products you purchase will give you superb performance for many years to come. THX Select2 Plus requirements define hundreds of parameters, including power amplifier performance, and pre-amplifier performance and operation for both digital and analog domains. THX Select2 Plus receivers also feature proprietary THX technologies (e.g., THX Mode) which accurately translate movie soundtracks for home theater playback.

Qdeo and QuietVideo are trademarks of Marvell or its affiliates.

HQV® (Hollywood Quality Video) is registered trademark of IDT, inc.

“x.v.Color” is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master Audio, and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

*10

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

*11

HD Radio™, HD Radio Ready™, and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation. This HD Radio Ready™ receiver is ready to receive HD Radio broadcasts when connected to the Onkyo UP-HT1 HD Radio tuner module (sold separately).

*12

“DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital Living Network Alliance.”

*12

Windows and the Windows logo are trademarks of the Microsoft group of companies.

“Xantech” is a registered trademark of Xantech Corporation.

“Niles” is a registered trademark of Niles Audio Corporation.

This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license from Audyssey Laboratories™, Inc. U.S. and foreign patents pending.

Audyssey MultEQ Audyssey Dynamic Volume

XT, Audyssey Dynamic EQ®,

and Audyssey DSX™ are

registered trademarks and trademark of Audyssey Laboratories, Inc.

Music Optimizer™ is a trademark of Onkyo Corporation.

“HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.”

Page 8

Front & Rear Panels

Front Panel

(North American models)

a

bcd

e h i jklm

g o

n p

q

sr

(Australian models)

t

The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item.

a 8On/Standby button (22) b Zone 2 and Off buttons (67) c Zone 3 and Off buttons (67) d Zone Level buttons (67) e Monitor Out button (44) f Remote control sensor and transmitter (4) g Tone and Tone Level buttons (63) h Display (9) i Listening Mode buttons (34) j Dimmer button (North American models) (40) k Memory button (29) l Tuning Mode button (28)

m Display button (41) n Setup button (43) o Tuning, Preset (28 to 29), arrow and Enter

buttons

p Return button q Master Volume control (23) r Phones jack (41) s Setup Mic ja t Input selector buttons (23) u USB port (18) v AUX Input jacks (17, 18) w RT/PTY/TP button (Australian models) (30)

u

ck (31)

v

Page 9

Display

dcb egfa h

For detailed information, see the pages in parentheses.

a Speaker/channel indicators b Z2 (Zone 2) indicator (67) c Z3 (Zone 3) indicator (67) d Listening mode and format indicators (34, 65) e 1, 3 and cursor indicators (24) f NET indicator (25, 62) g Tuning indicators

RDS indicator (excluding North American models) (29)

AUTO indicator (28) TUNED indicator (28) FM STEREO indicator (28)

h Audio input indicators i Bi AMP indicator (14, 47) j Audyssey indicator (31, 52)

Dynamic EQ indicator (52)

- (Dolby) Vol indicator (51)

Dynamic Vol indicator (53)

k Headphone indicator (41) l Message area m MUTING indicator (41) n Volume level (23) o USB indicator (24, 25) p SLEEP indicator (40, 57)

mno

Page 10

Rear Panel

h i j

rut

a DIGITAL IN COAXIAL and OPTICAL jacks b RS232 port

Terminal for control.

c u REMOTE CONTROL jack d USB port e UNIVERSAL PORT jack f ETHERNET port g HDMI IN and HDMI output (HDMI OUT MAIN and

HDMI OUT SUB) jacks

h MONITOR OUT V and S jacks i COMPONENT VIDEO IN and MONITOR OUT

jacks

j COMPONENT VIDEO ZONE 2 OUT jacks k IR IN (A/B) and OUT jacks l 12V TRIGGER (A/B/C) OUT jacks m ZONE 2 OUT V jack n FM ANTENNA jack and AM ANTENNA terminal o PC IN jack p AC INLET q GND screw

sq v

k lg onma fdebc

r Composite, S-Video and analog audio jacks

(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN, GAME IN, PC IN, TV/CD IN and PHONO IN)

s Multichannel input jacks

(FRONT L/R, CENTER, SURR L/R, SURR BACK L/R and SUBWOOFE

t PRE OUT jacks

(FRONT L/R, CENTER, SURR L/R, SB/FH/FW SUBWOOFER)

SB···Surround Back, FH···Front High, FW···Front Wide

u ZONE 2 and ZONE 3 PRE/LINE OUT jacks v Speaker Terminals

(FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, FRONT HIGH L/R and FRONT WIDE/ZONE 2 L/R)

See “Connecting the AV Receiver” for connection (➔ pages 12 to 21).

Page 11

Remote Controller

Controlling the AV Receiver

d e

To control the AV receiver, press Receiver to select Receiver mode.

You can also use the remote controller to control Integra/Onkyo Blu-ray Disc/DVD player, CD player, and other components. See “Entering Remote Control Codes” for more details (➔ page 74).

For detailed information, see the pages in parentheses.

a 8Receiver button (22) b Activities buttons (42, 78)

c Remote Mode/Input Selector buttons (23) d SP Layout button (41)

e Arrow q/w/e/r and Enter buttons f Setup button (43) g Listening Mode buttons (34) h Dimmer button (40) i Display button (41) j Muting button (41) k VOL q/w button (23) l Return button

m Home button (40, 63) n Sleep button (40)

■ Controlling the tuner

To control the AV receiver’s tuner, press Tuner (or Receiver). You can select AM or FM by pressing Tuner repeatedly.

a Arrow q/w buttons (28) b D.

TUN button (29)

c Display button d CH +/– button (29) e Number buttons (29)

When you want to change the remote controller mode (target component) without changing the current input source, press Mode and within about 8 seconds, press Remote Mode. Then, using the same AV receiver’s remote controller, you can control the component corresponding to the button you pressed.

These buttons can also be used when a Remote Mode other than receiver mode is selected. (Pressing Home switches to Receiver mode.)

Page 12

Connections

Connecting the AV Receiver

Connecting Your Speakers

Connecting the Speaker Cables

The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.

Front high

right Front leftFront right Center

Surround

right

■ Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Front wide

right

Surround

back right

Front wide

left

Surround

back left

1/2" to 5/8" (12 to 15 mm)

Front high

left

Surround

left

■ Banana Plugs (North American models)

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Page 13

Speaker Configuration

Speaker Connection Precautions

The following table indicates the channels you should use depending on the number of speakers that you have.

No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 31) or manually (➔ page 47).

Number of speakers

Front speakers ✔✔✔✔✔✔✔✔✔✔✔✔✔✔ ✔ Center

speaker Surround

speakers Surround back

speaker Surround back

speakers Front high

speakers Front wide

speakers

If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.

Front high, surround back and front wide speakers cannot be used at the same time.

23456777889991011

✔ ✔✔✔✔✔✔✔✔✔✔✔ ✔

✔✔✔✔✔✔✔✔✔✔✔✔ ✔

✔✔✔✔

*1*2

✔✔✔✔

✔✔✔✔✔✔

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4ohms” (➔ page 47). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Make sure the metal core of the wire does not have contact with the AV receiver’s rear panel. Doing so may damage the AV receiver.

Attaching the Speaker Cable Labels

The speaker terminals are color-coded for identification purpose.

Speaker Color

Front left, Front high left, Front wide left, Zone 2 left

Front right, Front high right, Front wide right, Zone 2 right

Center Green Surround left Blue Surround right Gray Surround back left Brown Surround back right Tan

The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the table above. Then all you need to do is to match the color of each label to the corresponding speaker terminal.

White

Red

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Page 14

Using Dipole Speakers

You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions.

Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround dipole speakers (A) should be positioned so that their arrows point toward the TV/screen, while the surround back dipole speakers (B) should be positioned so that their arrows point toward each other, as shown.

TV/screen

Using a Powered Subwoofer

To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.

You can connect the powered subwoofer with two SUBWOOFER PRE OUT jacks respectively.

The same signal is output from each jack.

Tip

• If your subwoofer is unpowered and you’re using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier.

Bi-amping the Front Speakers

LINE INPUT

Powered subwoofer

1/3 of wall

LINE INPUT

position

Corner position

Important:

• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low) terminals.

• Bi-amping can be used only with speakers that support biamping. Refer to your speaker manual.

Bi-amping provides improved bass and treble performance. When bi-amping is used, the AV receiver is able to drive up

to a 5.1 speaker system in the main room. Once you’ve completed the bi-amping connections as shown and turned on the AV receiver, you must set the speaker

setting to enable bi-amping (➔ page 47).

Front right

Tweeter (high)

Woofer (low)

Front left

Page 15

Connecting a Power Amplifier

If you want to use a more powerful power amplifier, you can use the AV receiver as a preamp. Connect all speaker outputs to the power amplifier. See the manuals supplied with your amplifier for details.

Note

Specify “None” for any channel that you don’t want to output (➔ page 48). SB···Surround Back, FH···Front High, FW···Front Wide

Power amplifier

Page 16

About AV Connections

Connecting AV components

HDMI cable Other cables

: Video & Audio : Video : Audio

AV receiverAV receiver

TV, projector, etc.

Blu-ray Disc/DVD

player

Game console

TV, projector, etc.

Blu-ray Disc/DVD

player

Game console

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Right!

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

AV Cables and Jacks

Wrong!

Signal Cable Jack Description

Video and Audio

Video Component video Component video separates the luminance (Y) and color

HDMI HDMI connections can carry digital video and audio.

HDMI

Green

Blue

Red

difference signals (P

B, PR), providing the best picture

quality (some TV manufacturers label their component video sockets slightly differently).

Analog RGB This is a conventional analog interface to connect a PC and

a display device (also called D-Sub or D-subminiature).

S-Video S-Video separates the luminance from color signals and

provides better picture quality than composite video.

Composite video Composite video is commonly used on TVs, VCRs, and

Audio Optical digital

audio

Yellow

OPTICAL

other video equipment. Optical digital connections allow you to enjoy digital

sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as coaxial.

Coaxial digital audio

Orange

Coaxial digital connections allow you to enjoy digital sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as optical.

Analog audio (RCA)

Multichannel analog audio (RCA)

White

Red

Analog audio connections (RCA) carry analog audio.

This cable carries multichannel analog audio and is typically used to connect DVD players with a 7.1-channel analog audio output. Several standard analog audio cables can be used instead of a multichannel cable.

Available sampling rate for PCM input signal (stereo/mono) is 32/44.1/48/88.2/96 kHz. In case of an HDMI connection,

176.4/192 kHz is also available.

Note

• The AV receiver does not support SCART plugs.

• The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution

• To prevent shutter damage, hold the optical plug straight when inserting and removing.

Page 17

Connecting Components with HDMI

VCR or DVD recorder/Digital Video Recorder

Game console

Blu-ray Disc/DVD player

Personal computer

Satellite/cable set-top box, etc.

TV, projector,

etc.

Camcorder

Connect your components to the appropriate jacks. The default input assignments are shown below.

✔: Assignment can be changed (➔ page 45).

Jack Components Assignable

Input HDMI IN 1 Blu-ray Disc/DVD player ✔

HDMI IN 2 VCR or DVD recorder/Digital Video Recorder ✔ HDMI IN 3 Satellite/cable set-top box, etc. ✔ HDMI IN 4 Game console ✔ HDMI IN 5 Personal computer ✔ HDMI IN 6 Other components ✔ HDMI IN 7 Other components ✔ AUX Input HDMI Camcorder

Output HDMI OUT MAIN TV

HDMI OUT SUB projector, etc.

See also:

• “Connection Tips and Video Signal Path” (➔ page 88)

• “Using an RIHD-compatible TV, Player, or Recorder” (➔ page 91)

• “About HDMI” (➔ page 93)

■ Audio Return Channel (ARC) function

Audio Return Channel (ARC) function enables an HDMI capable TV to send the audio stream to the HDMI OUT MAIN of the AV receiver.

• This function can be used when: – your TV is ARC capable, and –the TV/CD input selector is selected, and

–“HDMI Control(RIHD)” is set to “On”(➔ page 60), and –“Audio Return Channel” is set to “Auto” (➔ page 61).

Tip

• To listen to audio received by the HDMI IN jacks through your TV speakers: – Set the “HDMI Control(RIHD)” setting to “On” (➔ page 60) for an p-compatible TV. – Set the “Audio TV Out” setting to “On” (➔ page 61) when the TV is not compatible with p, or the “HDMI

Control(RIHD)” setting to “Off”. – Set your Blu-ray Disc/DVD player’s HDMI audio output setting to PCM. – To listen to TV audio through the AV receiver, see “Connecting Your Components” (➔ page 18).

Note

• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

•As the “Audio TV Out” setting is set to “On” (➔ page 61) to hear from your TV speakers, the sound will also be output from the AV receiver’s speakers if you adjust the volume of the AV receiver. Similarly, as the (➔ page 60) to hear from the speakers of an p-compatible TV, the AV receiver’s speakers will produce sound if you adjust the volume of the AV receiver, while the TV speakers will be muted. To stop the AV receiver’s speakers from producing sound, you can either change the settings on the AV receiver or on the TV, or turn down the volume of the AV receiver.

“HDMI Control(RIHD)” setting is set to “On”

Page 18

Connecting Your Components

The on-screen menus appear only on a TV that is connected to the HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Front

CA B

Rear

FDH JE G I

Page 19

Connect your components to the appropriate jacks. The default input assignments are shown below. See “Connection Tips and Video Signal Path” for more information (➔ page 88).

✔: Assignment can be changed (➔ page 46).

No. Jack/Port Components Assignable

A B C

, AUX Input Video

USB AUX Input Video Camcorder, etc

*1*2

USB

Audio L/R Digital

DIGITAL IN COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player ✔

2 (VCR/DVR) VCR or DVD recorder/digital video recorder, RI

3 (CBL/SAT) Satellite/cable set-top box, RI dock, etc. ✔

OPTICAL 1 (GAME) Game console ✔

2 (TV/CD) TV, CD player ✔

USB

UNIVERSAL PORT Universal port option dock (UP-A1 etc.)

ETHERNET Router

MONITOR OUT TV, projector, etc.

BD/DVD IN Blu-ray Disc/DVD player VCR/DVR IN VCR or DVD recorder/digital video recorder, RI

CBL/SAT IN Satellite/cable set-top box, etc. GAME IN Game console, RI dock PC IN TV/CD IN TV, CD player, cassette tape deck, MD, CD-R,

PHONO IN

COMPONENT VIDEO

IN 1 (BD/DVD) Blu-ray Disc/DVD player, RI dock ✔ IN 2 (CBL/SAT) Satellite/cable set-top box, RI dock, etc. ✔ IN 3 (GAME) Game console, RI dock ✔ MONITOR OUT TV, projector, etc.

PC IN

Multichannel input

iPod/iPhone, MP3 player, USB flash drive iPod/iPhone (video playback)

dock

MP3 player, USB flash drive

dock

Personal computer

Turntable Turntable

, RI dock

Personal computer DVD player, DVD-Audio, Super Audio CD-

capable player, MPEG decorder

✔

Note

Do not connect the AV receiver’s USB port to a USB port on your computer. Music on your computer cannot be played through the AV receiver in this way.

When USB input is selected, you can input video signals from the AUX Input Video jack.

Connect a turntable (MM) that has a built-in phono preamp to TV/CD IN, or connect it to PHONO IN with the phono preamp turned off. If your turntable (MM) doesn’t have a phono preamp, connect it to PHONO IN. If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer to connect to PHONO IN. See your turntable’s manual for details. If your turntable has a ground wire, connect it to the AV receiver’s GND screw. With some turntables, connecting the ground wire may produce an audible hum. If this happens, disconnect it.

When you connect your personal computer to PC IN and select the PC input selector, the video of the personal computer is output from the HDMI outputs. However, if you have assigned the HDMI inputs to the PC input selector, the AV receiver will output signals received from the HDMI inputs instead of signals from PC IN. To have the signals output from PC IN, select “-----” for “PC” in the “HDMI Input” setting (➔ page 45).

To select the multichannel input, select the BD/DVD input selector and see “Audio Selector” (➔ page 57). To adjust the subwoofer sensitivity for the multichannel input, see “Subwoofer Input Sensitivity” (➔ page 47).

• With connection D, you can enjoy Dolby Digital and DTS. (To record or listen the audio in Zone 2/3 as well, use D

H.)

and

• With connection

H, you can listen to and record audio from external components while you are in Zone 2/3.

• With connection H, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to connect to the main stereo.

■ How to record a video source

With the connections described above, you cannot record the videos through the AV receiver. See “Recording” about connections for video recording (➔ page 42).

Page 20

Connecting Integra/Onkyo u Components

Make sure that each Integra/Onkyo component is

connected with an analog audio cable (connection

H in the hookup examples) (➔ page 18).

Make the u connection (see the illustration).

If you’re using an RI Dock, or cassette tape deck,

change the Input Display (➔ page 41).

With u (Remote Interactive), you can use the following special functions:

■ System On/Auto Power On

When you start playback on a component connected via u while the AV receiver is on Standby, the AV

receiver will automatically turn on and select that component as the input source.

■ Direct Change

When playback is started on a component connected via u, the AV receiver automatically selects that

component as the input source.

■ Remote Control

You can use the AV receiver’s remote controller to control your other u-capable Integra/Onkyo

components, pointing the remote controller at the AV receiver’s remote control sensor instead of the component. You must enter the appropriate remote control code first (➔ page 75).

Connecting a Recording Component

See “Recording” for details on recording (➔ page 42).

AUDI O

VCR, DVD recorder,

cassette tape deck,

CDR, MD recorder, etc.

VIDEO

ANALOG

e.g., CD player

RI Dock

Note

•Use only u cables for u connections. u cables are supplied with Integra/Onkyo components.

• Some components have two u jacks. You can connect either one to the AV receiver. The other jack is for connecting

additional u-capable components.

• Connect only Integra/Onkyo components to u jacks. Connecting other manufacturer’s components may cause a malfunction.

• Some components may not support all u functions. Refer to the manuals supplied with your Integra/Onkyo components.

• While Zone 2/3 is on, the System On/Auto Power On and Direct Change u functions do not work.

Note

• The AV receiver must be turned on for recording. Recording is not possible while it’s in standby mode.

• If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV receiver, connect the TV/VCR’s audio and video outputs directly to the recording VCR’s audio and video inputs. See the manuals supplied with your TV and VCR for details.

• Video signals connected to composite video inputs can be recorded only via composite video outputs. For example, if your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output.

• The surround sound and DSP listening modes cannot be recorded.

• Copy-protected Blu-ray Discs and DVDs cannot be recorded.

• Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded.

• DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.

AUDIO OUT

ANALOG

AUDIO OUT

Page 21

Connecting the Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use

the tuner.

North American models Australian models

Push. Insert wire. Release.

Assembling the AM loop antenna

Insert the plug fully into the jack.

Caution

Insert the plug fully into the jack.

• Be careful not to injure yourself when using thumbtacks.

Thumbtacks, etc.

AM loop antenna (supplied)

Note

• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception.

• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.

Indoor FM antenna (supplied)

Connecting the Power Cord

Connect the supplied power cord to the AV

receiver’s AC INLET.

To AC wall outlet

Plug the power cord into an AC wall outlet.

Note

• Before connecting the power cord, connect all of your speakers and AV components.

• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

• Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment.

• Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver.

Page 22

Turning On & Basic Operations

Turning On/Off the AV Receiver

8On/Standby

Turning On

Press 8On/Standby on the front panel.

Press Receiver followed by 8Receiver on the remote controller.

The AV receiver comes on, the display lights.

8Receiver

Receiver

Turning Off

Press 8On/Standby on the front panel.

Press Receiver followed by 8Receiver on the remote controller.

The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off.

Tip

• For details on power management settings, see “Auto Standby” (➔ page 61).

Page 23

Playback

The on-screen menus appear only on a TV that is connected to the HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

This section describes the procedure for using the remote controller unless otherwise specified.

Selecting the Language for the Onscreen Setup Menus

You can determine the language used for the onscreen setup menus. See “Language” in the “OSD Setup” (➔ page 59).

Playing the Connected Component

■ Operating with the remote controller

Press Receiver followed by Input Selector.

Start playback on the source component.

See also:

• “Playing an iPod/iPhone via USB” (➔ page 24)

• “Playing a USB Device” (➔ page 25)

• “Listening to Internet Radio” (➔ page 25)

• “Playing Music Files on a Server” (➔ page 27)

• “Remote Playback” (➔ page 27)

• “Listening to AM/FM Radio” (➔ page 28)

• “iPod/iPhone Playback via Onkyo Dock” (➔ page 70)

• “Controlling Other Components” (➔ page 73)

To adjust the volume, use VOL q/w.

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ page 34)

• “Audyssey” (➔ page 52)

■ Operating on the AV receiver

Use the input selector buttons to select the input

source.

Start playback on the source component.

To adjust the volume, use the Master Volume

control.

Select a listening mode and enjoy!

Controlling Contents of USB or Network Devices

See “Controlling Other Components” about the operation of other components (➔ page 73).

Press USB or NET first.

c d

e f

l m

n o

p q

Top Menu

This button displays the top menu for each media or service.

q/w and Enter

These buttons navigate through the menus.

e/r

This button cycles through pages.

Playlist e/r

In Standard Mode (iPod/iPhone), this button selects playlists.

This button starts playback.

This button selects the beginning of the current song. Pressing this button twice selects the previous song.

This button fast-reverses the current song.

This button pauses playback.

You can toggle between the playback screen and the list screen during playback.

Display

This button switches between song informations.

Album +/–

In Standard Mode (iPod/iPhone), this button selects albums.

Page 24

This button returns to top menu of the Internet Radio service.

Return

This button returns to the previous menu.

This button selects the next song.

This button fast-forwards the current song.

This button stops playback.

Mode

You can switch between Standard Mode and Extended Mode during iPod/iPhone playback.

Random

This button performs random playback.

Repeat

Press this button repeatedly to cycle through the repeat modes.

Note

• The buttons you can use will differ depending on the devices and media used for playback.

Understanding Icons on the Display

This section describes icons that appear on the display during media playback.

Displayed Icons

Icon Description

Folder

Track

Playback

Pause

Fast Forward

Playing an iPod/iPhone via USB

This section explains how to play music/video files on the iPod/iPhone.

Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic, iPod with video, iPod nano (1st, 2nd, 3rd, 4th, 5th and 6th

generation), iPhone 4, iPhone 3GS, iPhone 3G, iPhone

Press USB repeatedly to select the “USB(Front)”

input.

Connect the USB cable that comes with the

iPod/iPhone to the USB port on the front of the AV receiver.

While reading the contents of your iPod/iPhone, the message “Connecting...” appears on the display.

The USB indicator lights. It will flash if the AV receiver cannot read the iPod/iPhone.

Press Mode repeatedly to switch to Extended

Mode (Music) or Extended Mode (Video).

A list of your iPod/iPhone model’s contents appears. To open a folder, use q/w to select it, and then press

Enter.

Tip

• With the default settings, the iPod/iPhone is operated in Standard Mode.

• Pressing Mode repeatedly switches back to Standard Mode.

• When you disconnect the iPod/iPhone, the AV receiver stores the mode. This means that if you disconnect when in Extended Mode (Music), the AV receiver will start in Extended Mode (Music) the next time you connect the iPod/iPhone.

• You can also use q/w, Enter and Tuning Mode buttons on the front panel. Tuning Mode allows you to switch modes.

• When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

Use q/w to select a music/video file, and press

Enter or 1 to start playback.

Fast Reverse

Artist

Album

Repeat One Track

Repeat Folder (USB Device)

Repeat

Shuffle

Shuffle Album (iPod/iPhone)

Note

• Do not disconnect the USB device or USB cable that comes with iPod/iPhone to the USB port at the front of the AV receiver, while the message “Connecting...” appears on the display.

• If you connect an iPod or iPhone to the USB port on this device, no sound will be output from the headphones jack.

Page 25

Extended Mode (Music) control

The music content information is displayed (lists are displayed), and you can control the music content while looking at the screen.

Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers,

Shuffle Songs, Now Playing.

Extended Mode (Video) control

The video content information is displayed (lists are displayed), and you can control the video content while looking at the screen. Top screen list: Movies, Music Videos, TV Shows, Video Podcasts, Rentals.

Note

• To view the video contents of your iPod/iPhone, connect it to the USB port and AUX Input Video jack on the AV receiver’s front panel, using the official Apple Composite AV Cable.

• Depending on your iPod/iPhone model and generation, the displayed items may vary and the support for Extended Mode (Video) is not guaranteed.

Standard Mode control

The content information is not displayed, but can be operated using the iPod/iPhone or the remote controller (USB).

Note

• The following iPod models are not supported in Standard Mode. (They can only be controlled in Extended Mode). – iPod with video – iPod nano (1st generation)

Playing a USB Device

This section explains how to play music files from a USB device (e.g., USB flash drives and MP3 players).

See also:

• “Network/USB Features” (➔ page 94).

Listening to Internet Radio

You need to connect the AV receiver to your home network (➔ page 94).

You can select Internet radio stations by connecting to the AV receiver from your computer and selecting stations in your web browser. Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS). However, depending on the type of data or audio format used by the Internet radio station, you may not be able to listen to some stations.

Note

• Services available may vary depending on the region. See the separate instructions for more information.

Listening to vTuner Internet Radio

This unit includes the full vTuner Internet Radio Service at no additional charge. Once you have connected your unit to the Internet you can select vTuner Internet Radio to search for and play Internet radio stations and podcasts at any time. To enhance your Internet radio experience, the http://onkyo.vtuner.com/ portal is available to you as an easy way to browse to find stations, set up/organize your favorites, add your own stations, get help, etc. After the first time you try vTuner Internet Radio on your unit you can use the MAC Address of your unit to create a member login account (email address and password) on the http://onkyo.vtuner.com/ portal. To verify your MAC Address, please see “Network” (➔ page 62).

Press NET.

The “NET” screen appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

Use q/w/e/r to select “vTuner Internet Radio”

and then press Enter.

Press USB repeatedly to select the “USB(Front)”

or “USB(Rear)” input.

Plug your USB device into the AV receiver’s USB

port.

The USB indicator lights. It will flash if the AV receiver cannot read the USB device.

Press Enter.

A list of the device’s contents appears. To open a folder, use q/w to select it, and then press Enter.

Use q/w to select a music file, and press Enter or

1 to start playback.

Note

• Do not disconnect the USB device or USB cable that comes with iPod/iPhone to the USB port at the front of the AV receiver, while the message “Connecting...” appears on the display.

Page 26

Use q/w to select a program and then press Enter.

Playback starts.

My Music

0 : 11

Greate Artist

My Favorite

Press Menu to enable selection from the following menu items.

` Stations like this:

Stations like the one currently being played back are displayed.

` Add to My Favorites:

Adds a station to My Favorites list.

Press Top Menu to go to the top menu of the Internet Radio services.

Tip

• By pressing Search, you can toggle between the playback screen and the radio list screen.

Listening to Other Internet Radio

To listen to other internet radio stations, insert the following step after step 1 in the “Listening to vTuner Internet Radio” section.

On your computer, start your web browser and

enter the AV receiver’s IP address in the browser’s Internet address (URL) field.

The browser connects to the AV receiver (WEB Setup Menu).

Note

• The AV receiver’s IP address is shown on “IP Address” (➔ page 62).

• If you’re using DHCP, your router may not always allocate the same IP address to the AV receiver, so if you find that you can’t connect to the AV receiver, recheck the AV receiver’s IP address on the “Network” screen.

Click on the “My Favorites” tab.

Enter the preset name and Internet address

(URL).

Click “Save” to save the Internet radio station.

Registering My Favorites

You can add the currently playing song or station to the “My Favorites”. You can save up to 40 Internet radio stations.

Once you’ve added a station to the list, simply select it in the “My Favorites” menu, and then press Enter to start playback.

From the search results you can save the stations and songs but cannot listen to them directly.

■ Top menu of Internet Radio

` Create new station:

Add a favorite station or Internet radio to the My Favorites.

` Rename this station:

You can rename the stations and songs saved in “My Favorites” list.

` Delete from My Favorites:

You can delete the stations and songs saved in “My Favorites” list.

Press Menu with the station selected or while a

song is playing.

Use q/w to select “Add to My Favorites”, and press

Enter.

Use q/w/e/r to select “OK”, and then press

Enter.

Tip

• If you choose to rename the station, see “Name Edit”

➔ page 54).

(

The Internet radio station is then added to “My

Favorites”.

Page 27

Playing Music Files on a Server

You need to connect the AV receiver to your home network (➔ page 94).

Windows Media Player 11 Setup

This section explains how to configure Windows Media Player 11 so that the AV receiver can play the music files stored on your computer.

This section explains how to play music files on a computer or media server through the AV receiver (Server Playback).

Start your computer or media server.

Press NET.

The “NET” screen appears. The NET indicator lights. If it flashes, confirm the network connection.

Use q/w/e/r to select “dlna”, and press Enter.

Tip

• To go back to the previous screen, press Return.

Use q/w to select a server, and then press Enter.

The menu is displayed according to the server functions.

Note

• The search function does not work with media servers which do not support this function.

• Photos and movies stored on a media server cannot be accessed from the AV receiver.

• Depending on the sharing settings in the media server, the AV receiver may not able to access the content. See the instruction manual of the media server.

Use q/w to select an item, and then press Enter or

1 to start playback.

Start Windows Media Player 11.

On the “Library” menu, select “Media Sharing”.

The “Media Sharing” dialog box appears.

Select the “Share my media” check box, and then

click “OK”.

Select the AV receiver in the list, and then click

“Allow”.

Click “OK” to close the dialog box.

This completes the Windows Media Player 11 configuration. You can now play the music files in your Windows Media Player 11 library through the AV receiver.

Tip

• Windows Media Player 11 can be downloaded for free from the Microsoft web site.

Remote Playback

You need to connect the AV receiver to your home network (➔ page 94).

Remote Playback means you can play the music files stored on a media server or personal computer with the AV receiver by operating the controller device in the home network.

My favorite song 1

0 : 11

Artist name

My favorite album

Note

• Depending on the media server, 5/4/3 may not work.

• If the message “No Item.” appears, this means that no information can be retrieved from the server. In this case, check your server, network, and AV receiver connections.

Windows Media Player 12 Setup

This section explains how to configure Windows Media Player 12 so that the AV receiver can play the music files stored on your personal computer.

Start Windows Media Player 12.

On the “Stream” menu, select “Turn on media

streaming”.

A dialog box appears.

Move your cursor and click on “Turn on media

streaming”.

A list of media server appears. Wording may vary slightly depending on the network location.

Select the product in the list, and then click

“Allowed”.

Click “OK” to close the dialog box.

This completes the Windows Media Player 12 configuration.

You can now play the music files in your Windows Media Player 12 library.

Page 28

Using Remote Playback

Listening to AM/FM Radio

Start Windows Media Player 12.

To enable remote playback, you must first configure Windows Media Player 12.

Press NET.

The “NET” screen appears. The NET indicator lights. If it flashes, verify the network connection.

Use q/w/e/r to select “dlna”, and press Enter.

A list of media server appears.

Note

• Remote playback cannot be used while the music files of another media server are being played. You must stop their playback first.

On Windows Media Player 12, right-click on a

music file.

The right-click menu appears. For selecting another media server, select the desired media server from the “Other Libraries” menu on Windows Media Player

12.

Select the AV receiver from the right-click menu.

The “Play to” window appears and playback on the product starts. Operations during remote playback can be made from the “Play to” window of Windows 7 on your personal computer. During remote playback, operations (such as Playback, Pause, Fast Forward, Fast Rewind, Previous, Next, Repeat, Random) cannot be made.

Adjusting the Volume

You can adjust the volume by adjusting the volume bar in the “Remote playback” window. The default maximum volume level is 82 (0dB). If you wish to change this, enter the value from the Web Setup in your browser.

The volume value of the remote window and the volume value of the AV receiver may not always match. Adjustments you make to the volume in the AV receiver will not be reflected in the “Remote

playback” window.

This section describes the procedure using the buttons on the front panel unless otherwise specified.

Using the Tuner

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.

You can also change the frequency steps (➔ page 60).

Press Tuner to select either “AM” or “FM”.

In this example, FM has been selected. Each time you press Tuner, the radio band changes between AM and FM.

Band Frequency

(Actual display depends on the country.)

Tuning into Radio Stations

■ Auto tuning mode

Press Tuning Mode so that the AUTO indicator

lights on the display.

Press Tuning q/w.

Searching stops when a station is found. When tuned into a station, the TUNED indicator lights. When tuned into a stereo FM station, the FM

STEREO indicator lights on the display, as shown.

TUNED

AUTO

TERE

Tip

• Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono.

■ Manual tuning mode

In manual tuning mode, FM stations will be in mono.

Press Tuning Mode so that the AUTO indicator

goes off on the display.

Press and hold Tuning q/w.

The frequency stops changing when you release the button.

Press the buttons repeatedly to change the frequency one step at a time.

Page 29

■ Tuning into stations by frequency

You can tune into AM and FM stations directly by entering the appropriate frequency.

On the remote controller, press Tuner repeatedly

to select “AM” or “FM”, followed by D.TUN.

■ Deleting Presets

Select the preset that you want to delete.

See the previous section.

While holding down Memory, press Tuning

Mode.

The preset is deleted and its number disappears from the display.

(Actual display depends on the country.)

Within 8 seconds, use the number buttons to enter

the frequency of the radio station.

For example, to tune to 87.5 (FM), press 8, 7, 5. If you have entered the wrong number, you can retry

after 8 seconds.

Presetting AM/FM Stations

You can store a combination of up to 40 of your favorite AM/FM radio stations as presets.

Tune into the AM/FM station that you want to

store as a preset.

See the previous section.

Press Memory.

The preset number flashes.

(Actual display depends on the country.)

While the preset number is flashing (about 8

seconds), use Preset e/r to select a preset from 1 through 40.

Press Memory again to store the station or

channel.

The station or channel is stored and the preset number stops flashing.

Repeat this procedure for all of your favorite AM/FM radio stations.

Note

• You can name your radio presets for easy identification (➔ page 54). Its name is displayed instead of the band and

frequency.

■ Selecting Presets

To select a preset, use Preset e/r on the AV

receiver, or the remote controller’s CH +/–.

Tip

• You can also use the remote controller’s number buttons to select a preset directly.

Using RDS (excluding North American models)

RDS works only in areas where RDS broadcasts are available.

When tuned into an RDS station, the RDS indicator lights. When the station is broadcasting text information, the text can be displayed.

■ What is RDS?

RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.).

The AV receiver supports four types of RDS information:

PS (Program Service)

When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Pressing Display will display the frequency for 3 seconds.

RT (Radio Text)

When tuned to an RDS station that’s broadcasting text information, the text will be shown on the display as described in the next section.

PTY (Program Type)

This allows you to search for RDS radio stations by type (➔ page 30).

TP (Traffic Program)

This allows you to search for RDS radio stations that broadcast traffic information (➔ page 30).

Note

• In some cases, the text characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received. This is not a malfunction.

• If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.

Page 30

■ Displaying Radio Text (RT)

Press RT/PTY/TP once.

The RT information scrolls across the display.

Note

• The message “Waiting” may appear while the AV receiver waits for the RT information.

• If the message “No Text Data” appears on the display, no RT information is available.

■ Finding Stations by Type (PTY)

You can search for radio stations by type.

Press RT/PTY/TP twice.

The current program type appears on the display.

Use Preset e/r to select the type of program you

want.

See the table shown later in this chapter.

To start the search, press Enter.

The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search.

When a station you want to listen to is found, press

Enter.

If no stations are found, the message “Not Found” appears.

■ Listening to Traffic News (TP)

You can search for stations that broadcast traffic news.

Press RT/PTY/TP three times.

If the current radio station is broadcasting TP (Traffic Program), “[TP]” will appear on the display, and traffic news will be heard as and when it’s broadcast. If “TP” without square brackets appears, this means that the station is not broadcasting TP.

To locate a station that is broadcasting TP, press

Enter.

The AV receiver searches until it finds a station that’s broadcasting TP.

If no stations are found, the message “Not Found” appears.

RDS program types (PTY)

Type Display

None None News reports News Current affairs Affairs Information Info Sport Sport Education Educate Drama Drama Culture Culture Science and technology Science Varied Varied Pop music Pop M Rock music Rock M Middle of the road music Easy M Light classics Light M Serious classics Classics Other music Other M Weather Weather Finance Finance Children’s programmes Children Social affairs Social Religion Religion Phone in Phone In Travel Travel Leisure Leisure Jazz music Jazz Country music Country National music Nation M Oldies music Oldies Folk music Folk M Documentary Document Alarm test TEST Alarm Alarm!

Page 31

Using Basic Functions

Using the Automatic Speaker Setup

With the supplied calibrated microphone, Audyssey MultEQ®XT automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey MultEQ XT then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Audyssey MultEQ XT can be used with Audyssey Dynamic EQ Audyssey Dynamic Volume® (➔ page 52). Before using this function, connect and position all of your speakers. Audyssey MultEQ XT offers two ways of measuring: the “Audyssey Quick Start” and “Audyssey MultEQ XT Full Calibration”.

•“Audyssey Quick Start” uses the measurement from one position to perform the speaker setting only.

•“Audyssey MultEQ XT Full Calibration” uses the measurement from eight positions to correct room response in addition to the speaker setting.

The more positions are used in measuring, the better the listening environment will become. We recommend using a measurement from eight positions to create the best listening environment.

The Quick Start takes 2 minutes and Full Calibration takes about 20 minutes.

Total measurement time varies depending on the number of speakers.

and

fed

: Listening area

Note

• Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measurements. Close windows, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices. Turn off the cell phone (even if it is not in use) or place it away from all audio electronics.

• The microphone picks up test tones played through each speaker as Audyssey MultEQ XT Room Correction and Speaker Setup run.

• Audyssey MultEQ XT Room Correction and Speaker Setup cannot be performed while a pair of headphones is connected.

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV receiver is connected.

Set the speaker setup microphone at the Main

Listening Position a, and connect it to the Setup Mic jack.

a to h: Listening position

Setup Mic jack

Measurement procedure

To create a listening environment in your home theater that all listeners will enjoy, Audyssey MultEQ XT takes measurements at up to eight positions within the listening area. Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce inaccurate results.

■ First measurement position

Also referred to as the Main Listening Position this refers to the most central position where one would normally sit within the listening environment. Audyssey MultEQ XT uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.

■ Second

These are the other listening positions (i.e., the places where the other listeners will sit). You can measure up to eight positions.

−eighth measurement positions

Speaker setup microphone

The speaker setting menu appears.

Note

• The on-screen menus appear only on a TV that is connected to the HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Page 32

When you’ve finished making the settings, press

Enter.

MultEQ XT: Auto Setup

Speakers Type(Front) Normal Powered Zone 2 No Subwoofer Yes

AUDYSSEY

Perform the “Speaker Setup” according to your speaker configuration:

– Speakers Type(Front) (➔ page 47) – Powered Zone 2 (➔ page 47) – Subwoofer (➔ page 47)

If you use a powered subwoofer(s), go to step 4. If not, go to step 5.

When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the optional unit setting may appear on the speaker setting menu.

Adjust the subwoofer volume level to 75 dB, and

then press Enter.

Test tones are played through the subwoofer. Use the volume control on the subwoofer.

Note

• If your subwoofer does not have a volume control, disregard the displayed level and press Enter to proceed to the next step.

• If you set the subwoofer’s volume control to its maximum and the level displayed is lower than 75 dB, leave the subwoofer’s volume control at its maximum and press Enter to proceed to the next step.

Use q/w to select “Audyssey Quick Start” or

“Audyssey MultEQ XT Full Calibration”.

Press Enter.

Audyssey MultEQ

XT Room Correction and

Speaker Setup starts. Test tones are played through each speaker as Audyssey MultEQ XT Room Correction and Speaker

Setup runs. This process takes a few minutes. Please

refrain from talking during measurements and do not stand between speakers and the microphone.

Do not disconnect the speaker setup microphone during Audyssey MultEQ XT Room Correction and Speaker Setup, unless you want to cancel the setup.

If you select “Audyssey Quick Start”, you will go to step 9.

Place the setup microphone at the next position,

and then press Enter.

Audyssey MultEQ XT performs more measurements. This takes a few minutes.

When prompted, repeat step 7.

Use q/w to select an option, and then press Enter.

MultEQ XT: Auto Setup

-- Review Speaker Configuration --

Subwoofer : Yes Front : 100Hz Center : 40Hz Surround : 100Hz Front Wide : None Front High : None Surround Back : 120Hz Surround Back Ch : 2ch

Save Cancel

AUDYSSEY

The options are:

` Save:

Save the calculated settings and exit Audyssey MultEQ XT

Speaker Setup

Room Correction and

` Cancel:

Cancel Audyssey MultEQ XT Room Correction

and Speaker Setup

Tip

• You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by

using e/r.

Use q/w to select a target, and use e/r to change

the setting.

After the results of Audyssey MultEQ XT have been saved, the menu will display the “Audyssey” (➔ page 52), “Dynamic EQ” (➔ page 52), “Dynamic Volume” (➔ page 53) settings.

Note

• When “Audyssey Quick Start” has been used for measurement, “Audyssey” cannot be selected.

• These settings are applied to all input selectors.

Press Enter.

Disconnect the speaker setup microphone.

Note

• You can cancel Audyssey MultEQ XT Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

• Do not connect or disconnect any speakers during Audyssey MultEQ XT Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically when Audyssey MultEQ XT Room Correction and Speaker Setup starts.

• Changes to the room after Audyssey MultEQ XT Room Correction and Speaker Setup requires you run Audyssey MultEQ XT Room Correction and Speaker Setup again, as room EQ characteristics may have changed.

Page 33

Error Messages

Changing the Speaker Setup Manually

While Audyssey MultEQ®XT Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

MultEQ XT: Auto Setup

Ambient noise is too high.

Retry Cancel

AUDYSSEY

Error message

The options are:

` Retry:

Try again.

` Cancel:

Cancel Audyssey MultEQ XT Room Correction and Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different from that of the first measurement. Check the speaker connection.

• Writing Error!

This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact the dealer from whom you purchased this unit.

• Speaker Detect Error

This message appears if a speaker is not detected. “No” means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (➔ page 13).

You can manually make changes to the settings found during Audyssey MultEQ XT Room Correction and Speaker Setup.

See also:

• “Speaker Configuration” (➔ page 47)

• “Speaker Distance” (➔ page 48)

• “Level Calibration” (➔ page 49)

• “Equalizer Settings” (➔ page 49)

Note

• Please note that THX recommends any THX main speakers be set to “80Hz(THX)”. If you set up your speakers using Audyssey MultEQ XT Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to “80Hz(THX)” crossover (➔ page 47).

• Sometimes due to the electrical complexities of subwoofers and the interaction with the room, THX recommends setting the level and the distance of the subwoofer manually.

• Sometimes due to interaction with the room, you may notice irregular results when setting the level and/or distance of the main speakers. If this happens, THX recommends setting them manually.

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey MultEQ XT Room Correction and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker Configuration” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey MultEQ XT Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.

Page 34

Using the Listening Modes

Selecting Listening Modes

See “About Listening Modes” for detailed information about the listening modes (➔ page 35).

■ Listening Mode Buttons

Press Receiver first.

Music

Movie/TV

Game THX

Movie/TV button

This button selects the listening modes intended for use with movies and TV.

Music button

This button selects the listening modes intended for use

Game button

This button selects the listening modes intended for use with video games.

THX button

This button selects the THX listening modes.

Movie/TV, Music, Game

with music.

• The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI).

• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source Information” (➔ page 41).

• While a pair of headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo.

Page 35

About Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.

■ Explanatory Notes

SP Layout

Listening

mode buttons

Input Source

The following audio formats are supported by the listening mode.

A S D

This is mono (monophonic) sound. This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers.

This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth subwoofer channel (called the point-one channel).

This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two additional speakers that provide greater sound envelopment and more accurate positioning of sounds.

This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth channel from existing DTS 5.1 encoded material.

This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel sources.

abFront speakers c Center speaker deSurround speakers f Subwoofer(s) ghSurround back speakers ijFront high speakers klFront wide speakers

Speaker Layout

The illustration shows which speakers are activated in each channel. See “Speaker Configuration” for the speaker setup (➔ page 47).

ZXC

Press Receiver followed by SP Layout repeatedly to select the speakers you want to use: front high, front wide, or surround back.

Page 36

■ Onkyo-Original DSP Listening Modes

Listening Mode Description Input

Orchestra Suitable for classical or operatic music, this mode emphasizes the surround

Or c es t r ah

channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.

Unplugged Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the

Unp ugg e dl

front stereo image, giving the impression of being right in front of the stage.

Studio-Mix Suitable for rock or pop music, listening to music in this mode creates a

Stu io– Mixd

lively sound field with a powerful acoustic image, like being at a club or rock concert.

TV Logic This mode adds realistic acoustics to TV shows produced in a TV studio,

TV og i cL

surround effects to the entire sound, and clarity to voices.

Game-RPG In this mode, the sound has a dramatic feel with a similar atmosphere to

Gam – R P Ge

Orchestra mode.

Game-Action In this mode, sound localization is distinct with emphasis on bass.

Gam – Ac t i one

Game-Rock In this mode, sound pressure is emphasized to heighten live feel.

Gam –R o c ke

Game-Sports In this mode, reverberation is increased and sound localization decreased

Gam – S p ort se

slightly.

All Ch Stereo Ideal for background music, this mode fills the entire listening area with

Al l Ch Stereo

stereo sound from the front, surround, and surround back speakers.

Full Mono In this mode, all speakers output the same sound in mono, so the sound you

Fu l Monol

T-D (TheaterDimensional)

T – D

hear is the same regardless of where you are within the listening room.

With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by controlling how sounds reach the listener’s left and right ears. Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.

Source

A S D F G H

Speaker Layout

XCN

ZXC N

■ Listening Modes

Listening Mode Description Input

Direct In this mode, audio from the input source is output without surround-sound

Di rec t

processing. The speaker configuration (presence of speakers) and speaker distance settings are enabled, but much of the processing set via Home menu is disabled. A/V Sync does not have effect on the analog audio. See “Advanced Setup” for more details (➔ page 43).

Stereo Sound is output from the front left and right speakers and subwoofer.

Stereo

Mono Use this mode when watching an old movie with a mono soundtrack, or use

Mono

it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.

Multichannel This mode is for use with PCM multichannel sources.

Mu l t i ch

Source

A S D F G H

D F

Speaker Layout

ZXC

ZXC N

XCN

Page 37

Listening Mode Description Input

Source

Dolby Pro Logic IIx Dolby Pro Logic II

PL Mov i e

PL Mus i c

Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging.

If you’re not using any surround back speakers, Dolby Pro Logic II will be used instead of Dolby Pro Logic IIx.

SXCN

• Dolby PLIIx Movie

PL Game

Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g., TV, DVD, VHS).

PL x Mov i e

• Dolby PLIIx Music

Use this mode with any stereo or Dolby Surround (Pro Logic) music source

PL x Music

(e.g., CD, radio, cassette, TV, VHS, DVD).

• Dolby PLIIx Game

PL x Game

Use this mode with video games, especially those that bear the Dolby Pro Logic II logo.

• Dolby PLIIx Movie

• Dolby PLIIx Music

These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel sources for 7.1-channel playback.

Dolby Pro Logic IIz Height

PL z He i gh t

Dolby EX These modes expand 5.1-channel sources for 6.1/7.1-channel playback.

Dolby EX

Dolby D EX

Dolby Digital In this mode, audio from the input source is output without surround-sound

Dolby D

Dolby Digital Plus

Dolby D +

Dolby TrueHD

DTS

DTS-HD High Resolution Audio

DTS– HD HR

DTS-HD Master Audio

DTS– HD MST R

DTS Express

DTS E x p r e s s

DSD

Dolby Pro Logic IIz Height is designed to more effectively use existing program material when height channel speaker outputs are present. Dolby Pro Logic IIz Height can be used to upmix a variety of sources from movies and music, but are particularly well-suited to upmix game content.

They’re especially suited to Dolby EX soundtracks that include a matrixencoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects.

processing. The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via Home menu are enabled. See “Advanced Setup” for more details

(➔ page 43).

S D F

D H

DXCN

DXCN FXCN

DXCN

DXCN FXCN

DXCN

Speaker Layout

DSD

DTS 96/24 This mode is for use with DTS 96/24 sources. This is high-resolution DTS

DTS 96 / 2 4

DTS-ES Discrete

ES i screteD

with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.

This mode is for use with DTS-ES Discrete soundtracks, which use a discrete surround back channel for true 6.1/7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Discrete soundtrack.

DTS-ES Matrix

ES a t r i xM

This mode is for use with DTS-ES Matrix soundtracks, which use a matrixencoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.

DXCN

Page 38

Listening Mode Description Input

Source

DTS Neo:6 This mode expands any 2-channel source for up to 7.1-channel playback. It

uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.

Neo 6:Neo 6 C i nema:

• DTS Neo:6 Cinema

Use this mode with any stereo movie (e.g., TV, DVD, VHS).

S XCN

• DTS Neo:6 Music

Neo 6 Music:

Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD).

Neo 6:

•DTS Neo:6

This mode uses DTS Neo:6 to expand 5.1-channel sources for 6.1/7.1-

channel playback.

Audyssey DSX

Aud sse y DSXy

• Audyssey DSX

Audyssey DSX™ is a scalable system that adds new speakers to improve surround impression. Starting with a 5.1 system Audyssey DSX first adds Wide channels for the biggest impact on envelopment. Research in human

D F G

hearing has proven that information from the Wide channels is much more critical in the presentation of a realistic soundstage than Back Surround channels found in traditional 7.1 systems. Audyssey DSX then creates a pair of Height channels to reproduce the next most important acoustical and perceptual cues. In addition to these new Wide and Height channels, Audyssey DSX applies Surround Envelopment Processing to enhance the blend between the front and surround channels.

PL Mov i e DSX

• Dolby Pro Logic II Movie + Audyssey DSX

• Dolby Pro Logic II Music + Audyssey DSX

SbB

• Dolby Pro Logic II Game + Audyssey DSX

PL Mus i c DSX

The combination of Dolby Pro Logic II and Audyssey DSX modes can be used.

PL Game DSX

THX Founded by George Lucas, THX develops stringent standards that ensure

movies are reproduced in movie theaters and home theaters just as the director intended. THX Modes carefully optimize the tonal and spatial characteristics of the soundtrack for reproduction in the home-theater environment. They can be used with 2-channel matrixed and multichannel sources. Surround back speaker output depends on the source material and the selected listening mode.

THX C i n ema

Neo 6:THX Mu s i c

•THX Cinema

THX Cinema mode corrects theatrical soundtracks for playback in a home theater environment. In this mode, THX Loudness Plus is configured for cinema levels and Re-EQ, Timbre Matching, and Adaptive Decorrelation

D F G

are active.

THX Game s

•THX Music

THX Music mode is tailored for listening to music, which is typically mastered at significantly higher levels than movies. In this mode, THX Loudness Plus is configured for music playback and only Timbre Matching is active.

• THX Games

THX Games mode is meant for spatially accurate playback of game audio, which is often mixed similarly to movies but in a smaller environment. THX Loudness Plus is configured for game audio levels, with Timbre Matching active.

• Dolby Pro Logic II/IIx Movie + THX Cinema

SCN

• Dolby Pro Logic II/IIx Music + THX Music

• Dolby Pro Logic II/IIx Game + THX Games

The combination of Dolby Pro Logic II/IIx

and THX Cinema/Music/Games modes can be used. The PLII or PLIIx indicator lights on the display.

• Dolby Pro Logic IIx Movie + THX Cinema

• Dolby Pro Logic IIx Music + THX Music

D H

The combination of Dolby Pro Logic IIx and THX Cinema/Music modes can be used. The PLIIx indicator lights on the display.

Speaker Layout

Page 39

Listening Mode Description Input

Source

• Dolby Pro Logic IIz Height + THX Cinema

• Dolby Pro Logic IIz Height + THX Music

• Dolby Pro Logic IIz Height + THX Games

The combination of Dolby Pro Logic IIz Height and THX Cinema/Music/Games modes can be used. The PLIIz indicator lights on the display.

• DTS Neo:6 Cinema + THX Cinema

S D F G H

SCN

• DTS Neo:6 Music + THX Music

• DTS Neo:6 + THX Cinema

• DTS Neo:6 + THX Music

D H

• DTS Neo:6 + THX Games

The combination of DTS Neo:6 and THX Cinema/Music/Games modes can be used. The Neo:6 indicator lights on the display.

THX S 2 C i n ema

Neo 6:

• THX Select2 Cinema

This mode expands 5.1-channel sources for 7.1- channel playback. It does

this by analyzing the composition of the surround source, optimizing the

THX S2 Music

ambient and directional sounds to produce the surround back channel output.

T H X S 2 G a m e s

•THX Select2 Music

This mode is designed for use with music. It expands 5.1-channel sources

THX S u r r EX

for 7.1-channel playback.

•THX Select2 Games

This mode is designed for use with video games. It can expand 5.1-channel sources for 6.1/7.1-channel playback.

• THX Surround EX

This mode expands 5.1-channel sources for 6.1/7.1- channel playback. It’s especially suited to Dolby Digital EX sources. THX Surround EX, also known as Dolby Digital Surround EX, is a joint development between Dolby Laboratories and THX Ltd.

• Dolby Pro Logic II Game + THX Select2 Games

The combination of Dolby Pro Logic II Game and THX Select2 Games modes can be used. The PLII indicator lights on the display.

Speaker Layout

Note

Depending on the “Speaker Configuration” setting (➔ page 47), the output can be switched between the front high, front wide or surround back speakers by pressing SP Layout.

Based on the audio channel signal contained in the source, the corresponding speakers will output the sound.

If there are no surround back speakers, Dolby Pro Logic II is used.

For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.

AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound according to the player. In that case, set the output setting on the player side to PCM.

If there are no surround back speakers, DTS is used.

• This listening mode can be selected only when all the following conditions are satisfied: – Center speaker is connected. – Either of front high or front wide speakers is connected.

• Depending on the “Speaker Configuration” setting (➔ page 47), the output can be switched between the front high or front

wide speakers by pressing SP Layout.

• The listening modes cannot be selected with some source formats.

Page 40

Using the Home Menu

The Home menu provides you quick access to frequently used menus without having to go through the long standard menu. This menu enables you to change settings and view the current information.

The on-screen menus appear only on a TV that is connected to the HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Press Receiver followed by Home.

The Home menu will be superimposed on the TV screen.

Use q/w and Enter to make the desired selection.

■ Input

■ Audio

■ Video

■ Info

` You can select the input source while viewing the

information as follows: the name of input selectors, input assignments, radio information, and ARC function setting.

Press Enter to display the current input source, followed by q/w to select the desired input

source. Pressing Enter again switches to the selected input source.

` You can change the following settings: “Bass”,

“Treble”, “Subwoofer Level”, “Center Level”, “Dolby Volume”, “Audyssey”, “Dynamic EQ”, “Dynamic Volume”, “Late Night”, “Music Optimizer”, “Re-EQ” and “Re-EQ(THX)”.

See also:

• “Audyssey” (➔ page 52)

• “Using the Audio Settings” (➔ page 63)

` You can change the following settings: “Wide

Mode” and “Picture Mode

”.

See also:

• “Picture Adjust” (➔ page 55)

` You can view the information of the following

items: “Audio”, “Video” and “Tuner”.

Note

For the Port input selector, the name of Universal Port Option Dock will be displayed.

Only when you have selected “Custom” in the “Picture Mode” (➔ page 55), pressing Enter allows you to adjust

the following items via the Home menu “Contrast”, “Hue” and “Saturation”. Press Return to return to the “Picture Mode” setting.

Depending on the input source and listening mode, not all channels shown here output the sound.

: “Brightness”,

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

Press Receiver followed by Sleep repeatedly to

select the required sleep time.

The sleep time can be set from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator lights on the display when the sleep timer has been set. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears.

Tip

• If you need to cancel the sleep timer, press Sleep repeatedly until the SLEEP indicator goes off.

• To check the time remaining until the AV receiver sleeps, press Sleep. Note that if you press again on Sleep as the time being displayed is equal or inferior to 10 minutes, the sleep timer will go off.

Setting the Display Brightness

You can adjust the brightness of the AV receiver’s display.

Press Receiver followed by Dimmer repeatedly to

select:

• Normal

•Dim

• Dimmer

Tip

• (North American models) Alternatively, you can use the AV receiver’s Dimmer.

■ Listening Mode

` You can select the listening modes that are

grouped in the following categories: MOVIE/TV, MUSIC, GAME and THX.

Use q/w to select the category and e/r to select the listening mode. Press Enter to switch to the selected listening mode.

Page 41

Displaying Source Information

Selecting Speaker Layout

You can display various information about the current input source as follows. (Components connected to the UNIVERSAL PORT jack are excluded.)

Press Receiver followed by Display repeatedly to

cycle through the available information.

Tip

• Alternatively, you can use the AV receiver’s Display.

The following information can typically be displayed.

Input source

Listening mode

Signal format

Input signal

If the input signal is analog, “Analog” is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears.

Sampling

frequency

resolution

Output

resolution

Changing the Input Display

When you connect an u-capable Integra/Onkyo component, you must configure the input display so that

u can work properly. This setting can be done only from the front panel.

Press TV/CD, Game or VCR/DVR.

“TV/CD”, “GAME” or “VCR/DVR” appears on the display.

Press and hold down TV/CD, Game or VCR/DVR

(about 3 seconds) to change the input display.

Repeat this step to select the desired input display.

■ TV/CD:

■ Game:

■ VCR/DVR:

Note

• DOCK can be selected for the TV/CD, Game or VCR/DVR input selector, but not at the same time.

• Enter the appropriate remote control code before using the remote controller for the first time (➔ page 73).

TV/CD → DOCK

→

TAPE

GAME ↔ DOCK

VCR/DVR ↔ DOCK

→

You can set which speakers you want to use by priority.

Press Receiver followed by SP Layout repeatedly

to select:

` Speaker Layout:FH:

The sound from front high speakers is output by priority.

` Speaker Layout:FW:

The sound from front wide speakers is output by priority.

` Speaker Layout:SB:

The sound from surround back speakers is output by priority.

Note

•If the “Speakers Type(Front)” setting is set to “Bi-Amp” (➔ page 47), or the “Powered Zone 2” is set to “Yes” (➔ page 47), this setting cannot be selected.

• Playback conditions may be limited depending on the settings in “Speaker Settings” (➔ page 47) and “Speaker Configuration” (➔ page 47).

• When a listening mode which doesn’t support front high, front wide or surround back speakers is used, this setting cannot be selected.

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

Press Receiver followed by Muting.

The output is muted and the MUTING indicator flashes on the display.

Tip

• To unmute, press Muting again or adjust the volume.

• Muting is automatically cancelled when the AV receiver is set to standby.

Using Headphones

Connect a pair of stereo headphones with a

standard plug (1/4 inch or 6.3 mm) to the Phones jack.

Note

• Always turn down the volume before connecting your headphones.

• While the headphones plug is inserted in the Phones jack, the speakers are turned off. (The Powered Zone 2 speakers are not turned off.)

• When you connect a pair of headphones, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono or Direct.

• If you connect an iPod or iPhone to the USB port on this device, no sound will be output from the headphones jack.

Page 42

Using Easy Macros

By using Activities in Easy macro mode, you can sequentially operate Onkyo components via simple commands from a single-button press. These commands are user-definable. See “Using Normal Macros” (➔ page 78).

Press Activities (My Movie, My TV, or

My Music) to start the Easy macro command.

The default sequences of actions are described below. To change the related source component, see

“Changing the Source Components” shown later in this chapter.

■ My Movie

First, the TV, the Onkyo DVD player, and the AV receiver are turned on. The input selector is set to “BD/DVD”. Finally the player starts playback.

Depending on the start-up time of your Blu-ray Disc/DVD player, the AV receiver may not activate this playback

command. In this case, press 1 on the remote controller.

■ My TV

First, the TV, the cable set-top box, and the AV receiver are turned on. Then the input selector is set to “CBL/SAT”.

■ My Music

The Onkyo CD player and the AV receiver are turned on. The input selector is set to “TV/CD”. Finally, the player starts playback.

Note

• While the Easy Macro command is being processed, you cannot use other Activities. If you want to operate other components, first press All Off and use the desired Activities.

Turning Off the Components

This button turns off all components activated by the Easy Macro mode.

Press All Off.

First, the related components stop and turn off. Second, the AV receiver turns off. Finally, the TV turns off (or enters standby mode).

This step doesn’t apply to My Music, with the default settings.

With some televisions, the power may not be turned off (or enter standby mode).

*1*2

Changing the Source Components

You can change the source components activated by the Easy Macro mode.

While holding down Remote Mode for the

playback component you wish to assign, press and hold down the Activities to be changed (My Movie, My TV, or My Music) (about 3 seconds).

Activities flashes twice, indicating that the change is complete.

Examples:

If you wished to use My Music to start the Onkyo cassette recorder, you would press and hold down My Music (about 3 seconds) while holding down TV/CD until it flashes twice.

Restoring Default

You can restore Activities to the default settings.

While holding down Home, press and hold down

All Off until All Off lights (about 3 seconds).

Release Home and All Off, and press All Off

again.

All Off flashes twice.

Recording

This section explains how to record the selected input source to a component with recording capability.

AV Recording

Audio sources can be recorded to a recorder (e.g., cassette tape deck, CDR, MD recorder). Video sources can be recorded to a video recorder (e.g., VCR, DVD recorder).

Use the input selector buttons to select the source

that you want to record.

You can watch the source while recording. The AV receiver’s Master Volume control has no effect on recording.

On your recorder, start recording.

On the source component, start playback.

If you select another input source during recording, that input source will be recorded.

Page 43

Advanced Operations

Advanced Setup

The on-screen menus appear only on a TV that is connected to the HDMI OUT MAIN. If your TV is connected to other video outputs, use theAV receiver’s display when changing settings.

This section describes the procedure for using the remote controller unless otherwise specified.

On-screen Setup Menus

1. Input/Output Assign

2. Speaker Setup

3. Audio Adjust

4. Source Setup

5. Listening Mode Preset

6. Miscellaneous

7. Hardware Setup

8. Remote Controller Setup

9. Lock Setup

a Input/Output Assign

(➔ page 44)

1. Input/Output Assign

1. Monitor Out

2. HDMI Input

3. Component Video Input

4. Digital Audio Input

5. Analog Audio Input

b Speaker Setup

(➔ page 47)

2. Speaker Setup

1. Speaker Settings

2. Speaker Configuration

3. Speaker Distance

4. Level Calibration

5. Equalizer Settings

6. THX Audio Setup

c Audio Adjust

(➔ page 50)

3. Audio Adjust

1. Multiplex/Mono

2. Dolby

3. DTS

4. Audyssey DSX

5. Theater-Dimensional

6. LFE Level

d Source Setup

(➔ page 52)

4. Source Setup

1. Audyssey

2. IntelliVolume

3. A/V Sync

4. Name Edit

5. Picture Adjust

6. Audio Selector

e Listening Mode Preset

(➔ page 58)

5. Listening Mode Preset

1. BD/DVD

2. VCR/DVR

3. CBL/SAT

4. GAME

5. PC

6. AUX

f Miscellaneous

(➔ page 58)

6. Miscellaneous

1. Volume Setup

2. OSD Setup

3. 12V Trigger A Setup

4. 12V Trigger B Setup

5. 12V Trigger C Setup

g Hardware Setup

(➔ page 59)

7. Hardware Setup

1. Remote ID

2. Multi Zone

3. Tuner

4. HDMI

5. Auto Standby

6. Network

7. Firmware Update

h Remote Controller

Setup (➔ page 73)

8. Remote Controller Setup

1. Remote Mode Setup

2. Activities Setup

i Lock Setup

(➔ page 63)

9. Lock Setup

Setup

Common Procedures in Setup Menu

Receiver

Enter

q/w/e/r

Setup

The on-screen setup menus appear on the connected TV and provide a convenient way to change the AV receiver’s various settings. Settings are organized into 9 categories on the main menu. Carry out the settings by using the on-screen display.

Press Receiver followed by Setup.

Tip

• If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV.

Use q/w to select a menu, and then press Enter.

Use q/w to select a target, and then press Enter.

Use q/w to select an option, and use e/r to change

the setting.

Press Setup to close the menu. Press Return to return to the previous menu.

Note

• This procedure can also be performed on the AV receiver by using Setup, the arrow buttons, and Enter.

• During Audyssey MultEQ

XT Room Correction and Speaker Setup, messages, etc., that are displayed on the TV screen will appear in the Display.

Explanatory Notes

b c

Main Menu

■ Subwoofer

` Yes ` No

a Menu selection b Setting target c Setting options (default setting underlined)

Speaker Configuration

Return

Page 44

Input/Output Assign

Main Menu Input/Output Assign

Monitor Out

On the “Monitor Out” settings, you can select whether or not to have the video sources’ images output through the HDMI output.

If you connect your TV to HDMI output, “Monitor Out” setting is automatically set and composite video, S-Video, and component video sources are upconverted output.

Composite video, S-Video,

component video

Composite video, S-Video,

component video

OUT

If you connect your TV to the COMPONENT VIDEO MONITOR OUT (not the HDMI output), “Monitor Out”

setting is automatically set and composite video and S-

Video sources are upconverted

Composite video, S-Video Component video

Note

• See “Video Connection Formats” (➔ page 88) for charts showing how the “Monitor Out” and “Resolution” settings affect the video signal flow through the AV receiver.

and output.

OUT

HDMI

and

■ Monitor Out

` Analog:

Select this if your TV is connected to the

COMPONENT VIDEO MONITOR OUT, MONITOR OUT S, or MONITOR OUT V.

` HDMI Main

: Select this if your TV is connected to HDMI OUT MAIN.

` HDMI Sub:

Select this if your TV is connected to HDMI OUT SUB.

` Both:

Select this if your TVs are connected to HDMI OUT MAIN and HDMI OUT SUB. Video signals are output from both HDMI outputs at the resolution supported by both TVs.

` Both(Main):

Select this if your TVs are connected to HDMI OUT MAIN and HDMI OUT SUB. Video signals are output from both HDMI outputs but HDMI OUT MAIN will become a priority; depending on the resolution, video signals may not be output from HDMI OUT SUB.

` Both(Sub):

Select this if your TVs are connected to HDMI OUT MAIN and HDMI OUT SUB. Video signals are output from both HDMI outputs but HDMI OUT SUB will become a priority; depending on the resolution, video signals may not be output from

HDMI OUT MAIN.

Note

• If not connected to the same output you have selected in the “Monitor Out” setting, the “Monitor Out” setting will be automatically switched to “Analog” (➔ page 89).

• When using the DeepColor function, if the “Monitor Out” setting is set to “Both(Main)” or “Both(Sub)”, the number of bits may be limited due to the capability of your TV connected to a priority output.

Changing the “Monitor Out” setting manually

Press Monitor Out on the front panel.

The current setting is displayed.

Press Monitor Out on the AV receiver repeatedly

to select:

` Analog, HDMI Main, HDMI Sub, Both,

Both(Main) or Both(Sub)

Page 45

■ Resolution

` Through

: Select this to pass video through the AV receiver at the same resolution and with no conversion.

` Auto*2:

Select this to have the AV receiver automatically convert video at resolutions supported by your TV.

` 480p (480p/576p), 720p, 1080i, 1080p

Select the desired output resolution.

` 1080p/24*2:

Select this for 1080p output at 24 frames per second.

` 4K Upscaling

: Select this for an output resolution four times that of 1080p, resulting in 3840 × 2160 pixels.

` Source:

Output will be according to the resolution level which was set in the “Picture Adjust” setting (➔ page 55).

You can specify the output resolution for the HDMI Output(s) and COMPONENT VIDEO MONITOR OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV.

Tip

•The “Resolution” setting is set respectively of main, sub, and analog.

• You can see the picture by pressing Enter to check the “Resolution” setting (excluding NET input source).

Note

• Depending on the incoming video signal, the video playback may not be smooth or the vertical resolution may be lowered. In this case select anything other than “1080p/24”.

•If the “Monitor Out” setting is set to “Both”, this setting is fixed to “Auto”.

•When “Monitor Out” is set to either “HDMI Sub” or “Both(Sub)”, “1080/24p” and “4K Upscaling” cannot be selected.

PC IN (Analog RGB) input signal is output at 480p (480p/576p), 720p, 1080i resolution when the “Monitor Out” setting is set to “Analog” (➔ page 44) and the “Resolution” setting is set to “Through”.

These settings are not available when the “Monitor Out” setting is set to “Analog” (➔ page 44).

HDMI Input

If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2, you must assign “HDMI2” to the “BD/DVD” input selector.

If you’ve connected your TV to the AV receiver with an HDMI cable, composite video, S-video and component video sources can be upconverted HDMI output*1. You can set this for each input selector by selecting the “-----” option. See “Video Connection Formats” for more information on video signal flow and upconversion (➔ page 88).

Composite video, S-Video,

component video

Composite video, S-Video,

component video

This applies only when “Monitor Out” setting is set to other than “Analog” (➔ page 44).

Here are the default assignments.

Input selector Default assignment

BD/DVD HDMI1

VCR/DVR HDMI2

CBL/SAT HDMI3

GAME HDMI4

PC AUX FRONT (Fixed)

TV/CD -----

PHONO -----

PORT -----

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,

TV/CD, PHONO, PORT

` HDMI1, HDMI2, HDMI3, HDMI4, HDMI5,

HDMI6, HDMI7:

Select a corresponding HDMI input to which the video component has been connected.

` -----:

Output composite video, S-Video, and component video sources from the HDMI output. The video output signal from the HDMI output is the one configured in “Component Video Input”.

If you connect your personal computer to PC IN (Analog RGB), you must assign “-----” to the “PC” input selector.

Each HDMI input cannot be assigned to two input selectors or more. When HDMI1 - HDMI7 have already been assigned, you must first set any unused input selectors to “-----” or you will be unable to assign HDMI1 - HDMI7 to other input selectors.

and output by the

OUT

HDMI5

HDMI

Page 46

Note

• For composite video, S-Video, and component video upconversion for the HDMI output, the “Monitor Out” setting must be set to other than “Analog” (➔ page 44), and the “HDMI Input” setting must be set to “-----”. See “Connection Tips and Video Signal Path” for more information on video signal flow and upconversion (➔ page 88).

• If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of “Component Video Input”.

• When an HDMI IN is assigned to an input selector as explained here, the same HDMI IN will be set as a priority in the “Digital Audio Input” (➔ page 46). In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” setting (➔ page 57).

•The “TUNER” selector cannot be assigned and is fixed to the “-----” option.

•“AUX” is used only for input from the front panel.

• Do not assign an HDMI IN to the TV/CD selector while “HDMI Control(RIHD)” is set to “On” (➔ page 60), otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

• If you assign “-----” to an input selector that is currently selected in “HDMI Through” (➔ page 60), the “HDMI Through” setting will be automatically switched to “Off”.

• If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the “PORT” selector.

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,

TV/CD, PHONO, PORT

` IN1, IN2, IN3:

Select a corresponding component video input to which the video component has been connected.

` -----:

Select if you are using HDMI output, rather than the COMPONENT VIDEO MONITOR OUT, for the output from composite video, S-Video, and component video sources.

Note

• For composite video and S-Video upconversion for the COMPONENT VIDEO MONITOR OUT, the “Monitor Out” setting must be set to “Analog” (➔ page 44), and the “Component Video Input” setting must be set to “-----”. See “Connection Tips and Video Signal Path” for more information on video signal flow and upconversion (➔ page 88).

• If not connected to the same output you have selected in the “Monitor Out” setting, the “Monitor Out” setting will be automatically switched to “Analog” (➔ page 44).

• If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the “PORT” selector.

•The “TUNER” selector cannot be assigned and is fixed to the “-----” option.

Digital Audio Input

Component Video Input

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN 2, you must assign “IN2” to the “BD/DVD” input selector.

If you’ve connected your TV to the AV receiver with a component video cable, you can set the AV receiver so that composite video and S-Video sources are

upconverted

and output by the COMPONENT VIDEO

MONITOR OUT*1. You can set this for each input

selector by selecting the “-----” option.

Composite video, S-Video Component video

This applies only when “Monitor Out” setting is set to “Analog” (➔ page 44).

OUT

Here are the default assignments.

Input selector Default assignment

BD/DVD IN1

VCR/DVR - - - - -

CBL/SAT IN2

GAME IN3

PC -----

AUX -----

TV/CD -----

PHONO -----

PORT -----

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPTICAL1” to the “TV/CD” input selector.

Here are the default assignments.

Input selector Default assignment

BD/DVD COAXIAL1

VCR/DVR COAXIAL2

CBL/SAT COAXIAL3

GAME OPTICAL1

PC ----AUX FRONT (Fixed)

TV/CD OPTICAL2

PHONO -----

PORT -----

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,

TV/CD, PHONO, PORT

` COAXIAL1, COAXIAL2, COAXIAL3,

OPTICAL1, OPTICAL2:

Select a corresponding digital audio input to which the component has been connected.

` -----:

Select if the component is connected to an analog audio input.

Note

•When an HDMI IN is assigned to an input selector in “HDMI Input” (➔ page 45), the same HDMI IN will be set as a priority

in this assignment. In this case, if you want to use the coaxial or optical audio input, make the selection in the “Audio Selector” (➔ page 57).

Page 47

• Available sampling rates for PCM signals (stereo/mono) from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

• If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the “PORT” selector.

•“AUX” is used only for input from the front panel.

•The “TUNER” selector cannot be assigned and is fixed to the “-----” option.

Analog Audio Input

Some DVD players output the LFE channel from their analog subwoofer output at 15 dB higher than normal. With this setting, you can change the AV receiver’s subwoofer sensitivity to match your DVD player.

■ Subwoofer Input Sensitivity

to 15dB in 5 dB steps.

` 0dB

Note

• This setting only affects signals connected to the AV receiver’s multichannel input subwoofer jack.

• If you find that your subwoofer is too loud, try the 10 dB or 15 dB setting.

Speaker Setup

Main menu Speaker Setup

Some of the settings in this section are set automatically by Audyssey MultEQ®XT Room Correction and Speaker Setup function (➔ page 31).

Here you can check the settings made by Audyssey MultEQ XT Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ XT Room Correction and Speaker Setup function.

Note

• These settings are not available in either of the following cases: – a pair of headphones is connected. –the “Audio TV Out” setting is set to “On” (➔ page 61).

–“HDMI Control(RIHD)” is set to “On” (➔ page 60) and

you’re listening through your TV speakers.

Speaker Settings

If you change these settings, you must run Audyssey MultEQ XT Room Correction and Speaker Setup again (➔ page 31).

If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. If you bi-amp the front speakers, you must change the “Speakers Type(Front)” setting. For hookup information, see “Bi-amping the Front Speakers” (➔ page 14).

Note

• When bi-amping is used, the AV receiver is able to drive up to

5.1 speakers in the main room.

• Before you change these settings, turn down the volume.

■ Speaker Impedance

` 4ohms:

Select if the impedance of any speaker is 4 ohms or more but less than 6.

` 6ohms

: Select if the impedances of all speakers are between 6 and 16 ohms.

■ Speakers Type(Front)

` Normal

: Select this if you’ve connected your front speakers normally.

` Bi-Amp:

Select this if you’ve bi-amped your front speakers.

■ Powered Zone 2

` No ` Yes:

Zone 2 speakers can be used. (Powered Zone 2 enabled.)

Note

• If the “Speakers Type(Front)” setting is set to “Bi-Amp”, Powered Zone 2 cannot be used.

• When the “Powered Zone 2” setting is set to “Yes”, the surround back, front wide and front high speakers cannot be used.

Speaker Configuration

This setting is set automatically by Audyssey MultEQ XT Room Correction and Speaker Setup function (➔ page 31).

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify “Full Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey MultEQ XT Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to “80Hz(THX)” crossover.

Note

• These settings are not available in either of the following cases: – a pair of headphones is connected. –the “Audio TV Out” setting is set to “On” (➔ page 61). –“HDMI Control(RIHD)” is set to “On” (➔ page 60) and

you’re listening through your TV speakers.

■ Subwoofer

` Yes ` No

■ Front

` Full Band ` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)

90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

Page 48

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed to “Full Band”.

■ Center*1, Surround*1, Surround Back

` Full Band ` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)

90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

` None

■ Front Wide

*1*2*4

, Front High

*1*2*4

` Full Band ` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),

90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz

` None

Note

“Full Band” can be selected only when “Full Band” is selected in the “Front” setting.

If the “Surround” setting is set to “None”, this setting cannot be selected.

If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.

If the “Speakers Type(Front)” setting is set to “Bi-Amp”, or the “Powered Zone 2” setting is set to “Yes”, this setting cannot be selected.

■ Surround Back Ch

` 1ch:

Select if only one surround back speaker L is connected.

` 2ch

: Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” Setting is set to “None”, this setting cannot be selected.

■ LPF of LFE

(Low-Pass Filter for the LFE Channel)

` 80Hz, 90Hz, 100Hz, 110Hz, 120Hz ` Bypass:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

■ Double Bass

This setting is NOT set automatically by

Audyssey MultEQ

XT Room Correction and Speaker

Setup function (➔ page 31).

` On ` Off(THX)

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

*2*3*4

Note

• This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “Full Band”.

• If you’re using THX-certified speakers, select “Off(THX)”.

■ Subwoofer Phase

` 0

` 180º:

Moves the subwoofer phase.

Note

•If the “Subwoofer” setting is set to “No”, this setting cannot be selected (➔ page 47).

■ Wireless Subwoofer

When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the speaker setting menu may appear on screen.

` Yes:

The audio is output from the speakers connected to the wireless unit.

` No

: The audio is not output from the speakers connected to the wireless unit.

When the wireless unit is connected to the UNIVERSAL PORT jack on the AV receiver, you can select if you wish to output the audio from the speakers connected to the wireless unit.

Note

•If the “Subwoofer” setting is set to “No”, this setting cannot be selected (➔ page 47).

Speaker Distance

This setting is set automatically by Audyssey MultEQ XT Room Correction and Speaker Setup function (➔ page 31).

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

■ Unit

` feet:

Distances can be set in feet. Range: 0.2ft to 30.0ft in

0.2 foot steps.

` meters:

Distances can be set in meters. Range: 0.06m to

9.00m in 0.06 meter steps.

(The default setting varies from country to country.)

■ Left, Front Wide Left, Front High Left, Center,

Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer

` Specify the distance from each speaker to your

listening position.

Page 49

Note

• These settings are not available in either of the following cases: – a pair of headphones is connected. –the “Audio TV Out” setting is set to “On” (➔ page 61).

–“HDMI Control(RIHD)” is set to “On” (➔ page 60) and

you’re listening through your TV speakers.

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ page 47).

Level Calibration

This setting is set automatically by Audyssey MultEQ®XT Room Correction and Speaker Setup function (➔ page 31).

Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

■ Left, Front Wide Left, Front High Left, Center

Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left

` –12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.

■ Subwoofer

` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.

Note

• These settings cannot be calibrated in either of the following cases: – a pair of headphones is connected. –the “Audio TV Out” setting is set to “On” (➔ page 61).

–“HDMI Control(RIHD)” is set to “On” (➔ page 60) and

you’re listening through your TV speakers.

– the AV receiver is muted.

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ page 47).

• The test tone is output at the standard level for THX, which is

0 dB (absolute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder.

For the center speaker and subwoofer, the level settings made by using the Home menu are saved in this menu (➔ page 40).

Tip

• If you’re using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

Equalizer Settings

With the Equalizer settings, you can adjust the tone of speakers individually with a 15-band equalizer. The volume of each speaker can be set.

■ Equalizer

` Manual:

You can adjust the equalizer for each speaker manually. Continue with the following procedure:

Press w to select “Channel”, and then use

e/r to select a speaker.

Use q/w to select a frequency, and then use

the e/r to adjust the level at that frequency.

The volume at each frequency can be adjusted from –6dB to 0dB

Tip

• Low frequencies (e.g., 25Hz) affect bass sounds; high frequencies (e.g., 16000Hz) affect treble sounds.

Use q to select “Channel”, and then use e/r

to +6dB in 1 dB steps.

to select another speaker.

Repeat steps 1 and 2 for each speaker. You cannot select speakers that you set to “No”

or “None” in the “Speaker Configuration” (➔ page 47).

` Off

Tone off, response flat.

Note

• You can select: “25Hz”, “40Hz”, “63Hz”, “100Hz”, “160Hz”, “250Hz”, “400Hz”, “630Hz”, “1000Hz”, “1600Hz”, “2500Hz”, “4000Hz”, “6300Hz”, “10000Hz” or “16000Hz”. And for the subwoofer, “25Hz”, “40Hz”, “63Hz”, “100Hz”, or “160Hz”.

• When the Direct listening mode is selected, the equalizer settings have no effect.

• If “Audyssey” is enabled, it prevails over this setting (➔ page 52).

THX Audio Setup

■ Surr Back Speaker Spacing

` <1ft (<0.3m) ` 1ft-4ft (0.3m-1.2m) ` >4ft (>1.2m)

You can specify the distance between your surround back speakers.

Note

• Cannot be set if: –“Surround Back Ch” is set to “1ch” (➔ page 48). –“Speakers Type(Front)” is set to “Bi-Amp” (➔ page 47). –“Surround Back” is set to “None” (➔ page 48). –“Powered Zone 2” is set to “Yes” (➔ page 47) and Zone 2

turned on (➔ page 67).

Page 50

■ THX Ultra2/Select2 Subwoofer

` No ` Yes

If you’re using a THX-certified subwoofer, set this setting to “Yes”.

Note

•If the “Subwoofer” setting is set to “No”, this setting cannot be selected (➔ page 47).

■ BGC

` Off ` On

You can apply THX’s Boundary Gain Compensation (BGC) to compensate the perceived exaggeration of low frequencies for listeners sitting very close to a room boundary (i.e., wall).

Note

• This setting is only available if “THX Ultra2/Select2 Subwoofer” is set to “Yes”.

•If the “Subwoofer” setting is set to “No”, this setting cannot be selected (➔ page 47).

■ Loudness Plus

` Off ` On

When the “Loudness Plus” is set to “On”, it is possible to enjoy even subtle nuances of audio expression at low volume.

This is only available when the THX listening mode is selected.

■ Preserve THX Settings

` Yes ` No

If this setting is set to “Yes”, Dynamic EQ and Dynamic Volume have no effect in THX listening mode.

Note

• This setting is fixed to “Yes” if “Loudness Plus” is set to “On”.

Audio Adjust

Main menu Audio Adjust

With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.

Multiplex/Mono

■ Multiplex

Input Channel

` Main ` Sub ` Main/Sub

This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.

■ Mono

Input Channel

` Left + Right ` Left ` Right

This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode.

Output Speaker

` Center

` Left / Right:

This setting determines which speakers output mono audio when the Mono listening mode is selected.

Note

•If the “Center” setting is set to “None” (➔ page 48), this setting cannot be selected.

Mono audio is output by the center speaker.

Mono audio is output by the front left and right speakers.

THX Loudness Plus

THX Loudness Plus is a new volume control technology featured in THX Ultra2 Plus™ and THX Select2 Plus™ Certified receivers. With THX Loudness Plus, home theater audiences can now experience the rich details in a surround mix at any volume level. A consequence of turning the volume below Reference Level is that certain sound elements can be lost or perceived differently by the listener. THX Loudness Plus compensates for the tonal and spatial shifts that occur when the volume is reduced by intelligently adjusting ambient surround channel levels and frequency response. This enables users experience the true impact of soundtracks regardless of the volume setting. THX Loudness Plus is automatically applied when listening in any THX listening mode. The new THX Cinema, THX Music, and THX Games modes are tailored to apply the proper THX Loudness Plus settings for each type of content.

Dolby

■ PL IIx Music (2ch Input)

These settings apply to only 2-channel stereo sources. If you’re not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic

IIx.

Panorama

` On ` Off

With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.

Page 51

Dimension

` –3 to 0

to +3

With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

Center Width

` 0 to 3

to 7

With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output from only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound.

■ PL IIz Height Gain

` Low ` Mid ` High

The Height Gain Control in Dolby Pro Logic IIz enables the listener to select how much gain is applied to the front high speakers. There are three settings, “Low”, “Mid” and “High”, and the front high speakers are accentuated in that order. While “Mid” is the default listening setting, the listener may adjust the Height Gain Control to their personal preference.

Note

•If the “Front High” setting is set to “None” (➔ page 48), this setting cannot be selected.

■ Dolby EX

` Auto:

If the source signal contains a Dolby EX flag, the Dolby EX or THX Surround EX listening mode is used.

` Manual

You can select any available listening mode.

This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.

Note

•If the “Surround Back” setting is set to “None” (➔ page 48), this setting cannot be selected.

•If the “Front High” or “Front Wide” setting is enabled (➔ page 48), this setting is fixed to “Manual”.

■ Dolby Volume

` Off ` On

Dolby Volume automatically adjusts the difference in volume levels which can occur between different contents or source components, freeing the user from having to make volume adjustments. Also, by adjusting the frequency balance according to the playback volume, it recreates the original source audio. Dolby Volume therefore provides comfortable listening, effectively controlling the volume level difference without unnatural changes in volume or sound quality to recreate the balance and nuance of the source audio.

Note

• When the “Dolby Volume” setting is set to “On”, “Dynamic EQ” and “Dynamic Volume” will be set to “Off”.

• If you would like to use Dolby Volume in THX listening modes, set the “Loudness Plus” and “Preserve THX Settings” settings to “Off” and “No”, respectively.

• When “Dolby Volume” is set to “On”, the Late Night function cannot be set.

■ Volume Leveler

` Off ` Low:

Low Compression Mode activated.

` Mid:

Medium Compression Mode activated.

` High

: High Compression Mode activated. This setting affects volume the most, causing all sounds to be of equal loudness.

“Volume Leveler” maintains the perceived loudness of all contents, coming from different channels or input sources.

Note

• If the “Dolby Volume” setting is set to “Off”, this setting cannot be selected.

■ Half Mode

` Off ` On

The Half Mode parameter turns Dolby Volume Half Mode processing on and off.

In off mode, Dolby Volume applies a bass and treble attenuation to the audio when the system gain exceeds reference level. This enables a more perceptually flat listening experience as human ears are more sensitive to bass and treble at higher levels. Some listeners however, prefer to have more bass and treble performance at higher gain levels.

Note

• If the “Dolby Volume” setting is set to “Off”, this setting cannot be selected.

• During Half Mode on playback, Dolby Volume does not apply a bass and treble attenuation when the system volume exceeds reference level thereby boosting perception of high and low frequencies.

Page 52

DTS

Source Setup

■ DTS Neo:6 Music

Center Image

` 0 to 2

to 5

The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel.

Changing the value from “0” to “5” will spread the sound of the center channel to left and right (outwards).

Audyssey DSX™

■ Soundstage

` –3dB to Reference

to +3dB With this setting, you can adjust the sound stage when using Audyssey DSX.

Note

• This listening mode can be selected only when all the following

conditions are satisfied: – The center speaker is connected. – The front high and front wide speakers are connected.

Theater-Dimensional

■ Listening Angle

` Wide

Select if the listening angle is 40 degrees.

` Narrow:

Select if the listening angle is 20 degrees. With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of the

front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

Front left speaker Front right speaker

20°/40°

LFE Level

■ Dolby Digital*1, DTS*2, Multich PCM, Dolby

TrueHD, DTS-HD Master Audio, DSD

` –QdB, –20dB, –10dB, or 0dB

With these settings, you can set the level of the LFE (Low Frequency Effects) channel individually for each input sources. If you find that low-frequency effects are too loud when using one of these sources, change the setting to –20 dB or

–Q dB.

Dolby Digital and Dolby Digital Plus sources

DTS and DTS-HD High Resolution sources

DSD (Super Audio CD) sources

Items can be set individually for each input selector.

Preparation

Press the input selector buttons to select an input source.

Main menu Source Setup

Audyssey

The tone for each speaker is set automatically by Audyssey MultEQ®XT Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup (➔ page 31).

■ Audyssey

` Off ` Movie:

Select this setting for movie material. The Audyssey indicator lights.

` Music:

Select this setting for music material. The Audyssey indicator lights.

Note

•If the “Audyssey” setting is set to “Off”, the “Equalizer” settings are applied (➔ page 49).

•When “Audyssey Quick Start” has been used for measurement, the “Audyssey”setting cannot be selected.

• Audyssey equalizing does not work with DSD sources.

• These technologies cannot be used when: – a pair of headphones is connected, or – Direct listening mode is selected.

■ Dynamic EQ

` Off ` On:

Audyssey Dynamic EQ® becomes active. The Dynamic EQ indicator lights.

With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels.

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level

— not just at reference level.

Note

• These technologies cannot be used when: – a pair of headphones is connected, or – Direct listening mode is selected.

Page 53

■ Reference Level

Audyssey Dynamic EQ

` 0dB

Reference Level Offset

This should be used when listening to movies.

` 5dB:

Select this setting for content that has a very wide dynamic range, such as classical music.

` 10dB:

Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference.

` 15dB:

Select this setting for pop/rock music or other program material that is mixed at very high listening levels and has a compressed dynamic range.

Movies are mixed in rooms calibrated for film reference. To achieve the same reference level in a home theater system each speaker level must be adjusted so that –30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system

automatically calibrated by Audyssey MultEQ

XT will play at reference level when the master volume control is set to the 0 dB position. At that level you can hear the mix as the mixers heard it. Audyssey Dynamic EQ is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film reference level is not always used in music or other nonfilm content. Audyssey Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard.

Note

•If “Dynamic EQ” setting is set to “Off”, these technologies cannot be used.

■ Dynamic Volume

` Off ` Light:

Activates Light Compression Mode.

` Medium:

Activates Medium Compression Mode.

` Heavy:

Activates Heavy Compression Mode. This setting affects volume the most. It quiets the loud parts, such as explosions, and boosts the quiet parts so they can be heard.

Note

• If you want to use Audyssey Dynamic EQ or Audyssey Dynamic Volume the “Loudness Plus” setting to “Off” and set “Preserve THX Settings” to “No” (➔ page 50).

• If you make Dynamic Volume active, “Dynamic EQ” is set to “On”. The Dynamic Vol indicator will light.

• When “Dynamic EQ” is set to “Off”, “Dynamic Volume” is automatically switched to “Off”.

• These technologies cannot be used when: – a pair of headphones is connected, or – Direct listening mode is selected.

About Audyssey Dynamic EQ

with THX listening modes, set

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works in tandem with

Audyssey MultEQ

XT to provide well-balanced sound

for every listener at any volume level.

About Audyssey Dynamic Volume

Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same whether watching movies, flipping between television channels, or changing from stereo to surround sound content.

Page 54

IntelliVolume

Name input area

■ IntelliVolume

` –12dB to 0dB

to +12dB in 1 dB steps. With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your

source components is louder or quieter than the others. Use e/r to set the level. If a component is noticeably louder than the others, use e

to reduce its input level. If it’s noticeably quieter, use r to increase its input level.

A/V Sync

■ A/V Sync

` 0msec

to 800msec in 1 msec steps.

When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals.

To view the TV picture while setting the delay, press Enter.

To return to the previous screen, press Return.

The range of values you can adjust will depend on whether your TV or display supports HDMI Lip Sync and if the “Lip Sync” setting is set to “On” or not (➔ page 61).

Note

• A/V Sync is disabled when the Direct listening mode is used

with an analog input source.

• This setting cannot be used with the NET input selector.

Name Edit

You can enter a custom name for each individual input selector and radio preset for easy identification. When entered, the custom name will appear on the display.

The custom name is edited using the character input screen.

■ Name

Use q/w/e/r to select a character, and then

press Enter.

Repeat this step to enter up to 10 characters.

To store a name when you’re done, be sure to

select “OK” by using q/w/e/r, and then press Enter.

4 - 4. Name Edit

Name

abcde fgh i j k lm nopqr s tu vwxyz 1234567890

{}| : <>

+10 CLR

Shift All Erase

ABCDEF GH I J KLM NOPQRS T UVWXY Z

!@#$%

[]

;

’,

Shift

+10 CLR

Shift All Erase

Back SpaceShift

Back Space OK

BD/DVD

–`

Space

()_ ~

Space

Space:

Enter a space character.

Shift

Toggles between lower and upper case characters.

(Left)/ (Right):

Moves the cursor left or right in the Name input area.

Back Space

Moves the cursor backward and deletes one character.

OK:

Confirms your entry.

Tip

This can also be performed by using +10 on the remote controller.

Press CLR on the remote controller to delete all the characters you have input.

To correct a character:

Use q/w/e/r to select “ ”(Left) or

“ ”(Right), and then press Enter.

Press Enter several times to highlight the

incorrect character (For each pressure, the cursor is moved on the next character).

Use q/w/e/r to select the correct character,

and then press Enter.

Tip

• To name a radio preset, use Tuner to sel ect AM o r FM , an d th en select the preset (➔ page 29).

• To restore a custom name to its default, erase the custom name by entering an empty white space for each letter.

Note

• This setting cannot be used for the NET and USB input selector.

Page 55

Picture Adjust

Using Picture Adjust, you can adjust the picture quality and reduce any noise appearing on the screen.

To view the TV picture while setting, press Enter. To return to the previous screen, press Return.

■ Wide Mode

This setting determines the aspect ratio.

` 4:3:

` Full:

` Zoom:

` Wide Zoom:

` Auto

According to the input signals and monitor output setting, the AV receiver automatically selects the “4:3”, “Full”, “Zoom” or “Wide Zoom” mode. See “Monitor Out” for details on the monitor output setting (➔ page 44).

■ Picture Mode

` Custom:

All settings can be performed manually.

` ISF Day:

Setting when a room is bright.

` ISF Night:

Setting when a room is dark.

` Cinema:

Select when the picture source is a movie or alike.

` Game:

Select when the video source is a game console.

` Streaming:

Attempts to reduce the mosquito noise and block artifact effects.

` Through:

Does not adjust picture quality (changes resolution).

*1*2

` Direct:

Does not adjust picture quality (does not change resolution). The video coming from an analog input and output by HDMI output(s) is processed in the same way as “Through”.

With “Picture Mode”, you can change the following settings to be suitable for the movie or game screen by one operation; “Game Mode”, “Film Mode”, “Edge Enhancement”, “Noise Reduction”, “Mosquito NR”, “Random NR”, “Block NR”, “Resolution”, “Brightness”, “Contrast”, “Hue”, “Saturation”, “Color

Temperature”, “Gamma”, “Red Brightness”, “Red Contrast”, “Green Brightness”, “Green Contrast”,

“Blue Brightness” or “Blue Contrast”. The receiver has been designed to incorporate setup and calibration standards established by the Imaging Science

Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal video performance and has implemented a training program for technicians and installers to use

these standards to obtain optimal picture quality from the receiver. Accordingly, Onkyo recommends that setup and calibration be performed by an ISF Certified installation technician.

■ Game Mode

*3*4*5

` Off ` On

If video signal delay occurs during playback on a video component (i.e., game console), select the corresponding input source and set the “Game Mode” setting to “On”. The delay will decrease but in return the picture quality will become poor.

■ Film Mode

*3*5*6

` Video:

“Film Mode” detection is not applied and the input signal is handled as a video source.

` Auto:

Detects whether the input signal is a video or a movie. If it is a movie, the appropriate conversion is

applied. The AV receiver will adjust to the picture source, automatically converting it to the appropriate progressive

signal and reproducing the natural quality of the original picture.

■ Edge Enhancement

*3*5*6

` Off ` Low ` Mid ` High

With Edge Enhancement, you can make the picture appear sharper.

■ Noise Reduction

*3*5*6

` Off ` Low ` Mid ` High

With this setting, you can reduce noise appearing on the screen. Select the desired level.

Page 56

■ Mosquito NR

*3*5*6*7

` Off ` Low ` Mid ` High

With Mosquito Noise Reduction, you can remove the shimmering or haziness that sometimes appears around objects in the picture. Mosquito noise can be an issue with overly compressed MPEG content.

■ Random NR

*3*5*6*7

` Off ` Low ` Mid ` High

With Random Noise Reduction, you can remove indiscriminate picture noise, such as film grain.

■ Block NR

*3*5*6*7

` Off ` Low ` Mid ` High

With Block Noise Reduction, you can remove the block distortion that sometimes appears in the picture. Block noise can be an issue with overly compressed MPEG content.

■ Resolution

*3*5

` Through:

Select this to pass video through the AV receiver at the same resolution and with no conversion.

` Auto:

Select this to have the AV receiver automatically convert video at resolutions supported by your TV. When the “Monitor Out” is set to “Analog”, this setting will be changed to “Through”.

` 480p (480p/576p), 720p, 1080i:

Select the desired output resolution.

` 1080p:

Select this for 1080p output and video conversion as necessary. When the “Monitor Out” is set to “Analog”, this setting will be changed to “1080i”.

` 1080p/24:

Select this for 1080p output at 24 frames per second. When the “Monitor Out” is set to “Analog”, this setting will be changed to “1080i”.

` 4K Upscaling:

Select this for an output resolution four times that of 1080p, resulting in 3840 × 2160 pixels. When the “Monitor Out” is set to “Analog”, this setting will

be changed to “1080i”. You can specify the output resolution for the HDMI Output(s) and have the AV receiver upconvert the picture

resolution as necessary to match the resolution supported by your TV.

Available only when “Source” has been selected in the “Resolution” of the “Monitor Out” setting (➔ page 44).

■ Brightness

` –50 to 0 to +50

*1*3*5

With this setting you can adjust the picture brightness. “–50” is the darkest. “+50” is the brightest.

■ Contrast

*1*3*5

` –50 to 0 to +50

With this setting you can adjust contrast. “–50” is the least. “+50” is the greatest.

*1*3*5

■ Hue

` –50 to 0 to +50

With this setting you can adjust the red/green balance. “–50” is the strongest green. “+50” is the strongest red.

■ Saturation

*1*3*5

` –50 to 0 to +50

With this setting you can adjust saturation. “–50” is the weakest color. “+50” is the strongest color.

■ Color Temperature

*3*5

` Warm

` Normal

` Cool

With this setting you can adjust the color temperature.

■ Gamma

*3*5

` –3 to 0 to +3

Adjust the balance of incoming picture R (red), G (green), and B (blue) color data signal to the output color data signal.

■ Red Brightness

*3*5

` –50 to 0 to +50

With this setting you can adjust the picture red brightness. “–50” is the darkest. “+50” is the brightest.

■ Red Contrast

*3*5

` –50 to 0 to +50

With this setting you can adjust red contrast. “–50” is the least. “+50” is the greatest.

■ Green Brightness

*3*5

` –50 to 0 to +50

With this setting you can adjust the picture green brightness. “–50” is the darkest. “+50” is the brightest.

■ Green Contrast

*3*5

` –50 to 0 to +50

With this setting you can adjust green contrast. “–50” is the least. “+50” is the greatest.

■ Blue Brightness

*3*5

` –50 to 0 to +50

With this setting you can adjust the picture blue brightness. “–50” is the darkest. “+50” is the brightest.

■ Blue Contrast

*3*5

` –50 to 0 to +50

With this setting you can adjust blue contrast. “–50” is the least. “+50” is the greatest.

Note

•“Picture Adjust” cannot be used with the NET input selector.

Page 57

This procedure can also be performed on the remote controller by using the Home menu (➔ page 40).

When a 3D video source is input, “Wide Mode” is fixed to “Full”.

When the “Picture Mode” setting is set to anything other than “Custom”, this setting cannot be used.

If the “Resolution” setting is set to “4K Upscaling” (➔ pages 45, 56), this setting is fixed to “Off”.

Press CLR if you want to reset to the default value.

If you are using the analog RGB input, this setting is not available.

When the “Noise Reduction” setting is set to anything other than “Off”, this setting cannot be selected.

Audio Selector

You can set priorities of audio output when there are both digital and analog inputs.

■ Audio Selector

` ARC:

The audio signal from your TV tuner can be sent to the HDMI OUT MAIN of the AV receiver. With this selection, the TV’s audio can be automatically selected as a priority among other assignments.

` HDMI:

This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is

automatically selected as a priority.

` COAXIAL:

This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority.

` OPTICAL:

This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority.

` Multich:

The AV receiver always outputs analog signals from multichannel analog input.

` Analog:

The AV receiver always outputs analog signals.

Note

• The setting is stored individually for each input selector.

• This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.

•The “Audio Selector” settings cannot be used with the NET,

USB and Port (with connected component) input selectors.

•“Multich” can be selected only when the selector is set to

“BD/DVD”.

You can select “ARC” if you select the TV/CD input selector. But you cannot if you’ve selected “Off” in the “Audio Return Channel” setting (➔ page 61).

■ Fixed Mode

` Off

: The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

` PCM:

Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced.

` DTS:

Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected in the “Audio Selector” setting, you can then specify the signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.

Note

• The setting is stored individually for each input selector.

• The setting will be reset to “Off” when you change the setting in “Audio Selector” (➔ page 57).

Charge Mode

■ Charge Mode

` Auto

: Power feeding is interrupted when your iPod/iPhone is fully charged.

` On:

Power feeding continues even if your iPod/iPhone is fully charged.

` Off:

Your iPod/iPhone is not charged.

You can specify how the power is fed to your iPod/iPhone when the AV receiver is in standby mode.

Note

• This setting cannot be selected when: – the UP-A1 Dock with docked iPod/iPhone is not connected to

the AV receiver, or

– the docked iPod/iPhone model is not supported.

• When the “Charge Mode” setting is set to “On”, or to “Auto” with your iPod/iPhone recharging, the SLEEP indicator is dimly lit in standby mode. In such conditions, the power consumption of the AV receiver slightly increases. With “Auto”, when the iPod/iPhone becomes fully charged, the SLEEP indicator goes off and the power consumption in standby mode is reduced.

Page 58

Listening Mode Preset

You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals. You can select other listening modes during playback, but the mode specified here will be resumed once the AV receiver has been set to standby.

Main menu Listening Mode Preset

Use q/w to select the input source that you want to

set, and then press Enter.

The following menu appears.

5. Listening Mode Preset

1. BD/DVD

2. VCR/DVR

3. CBL/SAT

4. GAME

5. PC

6. AUX

Use q/w to select the signal format that you want to

set, and then use e/r to select a listening mode.

Only listening modes that can be used with each input signal format can be selected (➔ pages 35 to 39). The “Last Valid” option means that the listening mode selected last will be used.

Note

• If you connect an input component (such as UP-A1 series Dock that seated iPod) to the UNIVERSAL PORT jack, the only listening modes you can assign to the “PORT” selector are specific to analog sound.

•For the Tuner input selector, only “Analog” will be available.

•For the NET or USB input selector, only “Digital” will be available.

■ Analog / PCM / Digital

With this setting, you can specify the listening mode used when an analog (CD, TV, LD, VHS, MD, turntable, radio, cassette, cable, satellite, etc.) or PCM digital (CD, DVD, etc.) audio signal is played.

■ Mono/Multiplex Source

With this setting, you can specify the listening mode used when a mono digital audio signal is played (DVD, etc.).

■ 2ch Source

With this setting, you can specify the listening mode used when 2-channel (2/0) stereo digital sources, such as Dolby Digital or DTS, are played.

■ Dolby D/Dolby D Plus/TrueHD

With this setting, you can specify the listening mode used when Dolby Digital or Dolby Digital Plus format digital audio signals are played (DVD, etc.). Specifies the default listening mode for Dolby TrueHD sources, such as Blu-ray or HD DVD (input via HDMI).

■ DTS/DTS-ES/DTS-HD

With this setting, you can specify the listening mode used when DTS or DTS-HD High Resolution format digital audio signals are played (DVD, LD, CD, etc.). Specifies the default listening mode for DTS-HD Master Audio sources, such as Blu-ray or HD DVD (input via HDMI).

■ Other Multich Source

Specifies the default listening mode for multichannel PCM sources from HDMI IN such as DVD-Audio, and DSD multichannel sources such as Super Audio CD.

Miscellaneous

Main menu Miscellaneous

Volume Setup

■ Volume Display

` Absolute

` Relative (THX):

With this setting, you can choose how the volume level is displayed. The absolute value 82 is equivalent to the relative value 0dB.

Note

• If the absolute value is set to 82, “82Ref” will appear on the display and the THX indicator will flash.

■ Muting Level

` –

This setting determines how much the output is muted when the muting function is used (➔ page 41).

■ Maximum Volume

` Off ` Off

With this setting, you can limit the maximum volume. To disable this setting, select “Off”.

■ Power On Volume

` Last

With this preference, you can specify the volume setting to be used each time the AV receiver is turned on.

To use the same volume level that was used when the AV receiver was turned off, select “Last”. The “Power On Volume” cannot be set higher than the “Maximum Volume” setting.

■ Headphone Level

` –12dB to 0dB

With this preference, you can specify the headphone volume relative to the main volume. This is useful if there’s a volume difference between your speakers and your headphones.

Displayed range is Min, 0.5 to 99.5, Max.

Displayed range is –QdB, –81.5dB to +18.0dB.

QdB (fully muted), –50dB to –10dB in 10 dB steps.

, 50 to 99 (Absolute display) , –32dB to +17dB (Relative display)

, Min, 1 to 99 or Max (Absolute display) , –QdB, –81dB to +18dB (Relative display)

to +12dB

Page 59

OSD Setup

■ On Screen Display

` On ` Off

This preference determines whether operation details are displayed on-screen when an AV receiver function is adjusted. Even when “On” is selected, operation details may not be output if the input source is connected to an HDMI IN.

■ Language

(North American models)

` English

(Australian models)

` English

This setting determines the language used for the onscreen setup menus.

, Deutsch, Français, Español, Italiano,

Nederlands, Svenska

, Deutsch, Français, Español, Italiano,

Nederlands, Svenska, 中文

12V Trigger A/B/C Setup

When several components are turned on simultaneously by using triggers A, B, and C, depending on the type of components, a large amount of current may be drawn momentarily. To prevent this, you can delay trigger signals A, B, and C individually. Another application of trigger delay is eliminating the “thump” noise that’s sometimes heard when a source component is turned on.

You can accomplish this by delaying the trigger signal for your power amplifier, so that it’s the last component to be turned on.

■ Delay

` 0sec, 1sec, 2sec, 3sec

When “0sec” is selected, the trigger signal is output as soon as the input source is changed.

Note

• By default, the “12V Trigger A Setup” menu is set to “0sec”, those on the “12V Trigger B Setup” menu is set to “1sec”, and those on the “12V Trigger C Setup” menu is set to “2sec”.

• Use a miniplug cable to connect the AV receiver’s 12V TRIGGER OUT A, B, or C jack to the 12 V trigger input on a connected component.

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,

TUNER, TV/CD, PHONO, PORT, NET, USB

` Off:

No trigger signal is output.

A 12-volt trigger signal is output when the connected component is selected as the source for:

` Main:

Main room.

` Zone 2:

Zone 2.

` Main/Zone 2:

Main room or Zone 2.

` Zone 3:

Zone 3.

` Main/Zone 3:

Main room or Zone 3.

` Zone 2/Zone 3:

Zone 2 or Zone 3.

` Main/Zone 2/Zone 3:

Main room, Zone 2, or Zone 3.

Note

• By default, all input sources on the “12V Trigger A Setup” menu are set to “Main”, those on the “12V Trigger B Setup” menu are set to “Main/Zone 2/Zone 3”, and those on the “12V Trigger C Setup” menu are set to “Zone 2”.

Hardware Setup

Main menu Hardware Setup

Remote ID

■ Remote ID

` 1

, 2, or 3 When several Integra/Onkyo components are used in the same room, their remote ID codes may overlap. To

differentiate the AV receiver from the other components, you can change its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.

Changing the remote controller’s ID

While holding down Receiver, press and hold

down Setup until Receiver lights (about 3 seconds) (➔ page 43).

Use the number buttons to enter ID 1, 2, or 3.

Receiver flashes twice.

Multi Zone

■ Zone 2 Out, Zone 3 Out

` Fixed

: The Zone 2/3 volume must be set on the amp in that zone.

` Variable:

The Zone 2/3 volume can be set on the AV receiver.

If you’ve connected your Zone 2/3 speakers to an amp with no volume control, set the “Zone 2 Out” and “Zone 3 Out” setting, respectively, to “Variable” so that you can set the volume, balance, and tone of zone 2 and volume of zone 3 on the AV receiver.

■ Zone 2 Maximum Volume,

Zone 3 Maximum Volume

, 50 to 99 (Absolute display)

` Off ` Off

, –32dB to +17dB (Relative display)

With this setting, you can limit the maximum volume for Zone 2/3.

Page 60

■ Zone 2 Power On Volume,

Zone 3 Power On Volume

` Last

, Min, 1 to 99 or Max (Absolute display) , –QdB, –81dB to +18dB (Relative display)

` Last

This setting determines what the volume will be for Zone 2/3 each time the AV receiver is turned on. To use the same volume level as when the AV receiver was last turned off, select “Last”. The “Zone 2 Power On Volume” and “Zone 3 Power

On Volume” cannot be set higher than the “Zone 2 Maximum Volume” and “Zone 3 Maximum Volume”

setting.

■ Zone 2 Component Video Out

` Yes

: Select if a TV in Zone 2 is connected the COMPONENT VIDEO ZONE 2 OUT.

` No:

Select if no TV in Zone 2 is connected the COMPONENT VIDEO ZONE 2 OUT.

If you’ve connected the COMPONENT VIDEO ZONE 2

OUT to a TV in Zone 2, this setting is set to “Yes”.

Note

•If the “Zone 2 Component Video Out” setting is set to “No”, the same video signal as COMPONENT VIDEO MONITOR

OUT is output from ZONE 2 OUT (component).

Tuner

For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when this setting is changed, all radio presets will be deleted.

■ AM/FM Frequency Step (North American

models)

` 10kHz/200kHz

` 9kHz/50kHz:

Select the frequency step according to your area.

■ AM Frequency Step (Australian models)

` 10kHz: ` 9kHz

Select the frequency step according to your area.

HDMI

■ HDMI Control(RIHD)

` Off ` On

Turn this setting on to allow components connected via HDMI to be controlled by the AV receiver (➔ page 91).

Note

• When the setting is set to “On” and the menu is closed, the names of connected p-compatible components and

“RIHD On” are displayed on the AV receiver. “Search…” → “(name)” → “RIHD On” When the AV receiver cannot receive the name of the component, it is displayed as “Player shows up and indicates the number of components, when two or more are received).

•When an p-compatible component is connected to the AV receiver via an HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray Disc/DVD player (being powered on) with the remote control of the AV receiver, the name of the Blu-ray Disc/DVD player will be displayed on the AV receiver.

•Set it to

• If operation is not normal when set to

• Refer to the connected component’s instruction manual for

•When “HDMI Control(RIHD)” setting is set to “On”, the

•The p control does not support HDMI OUT SUB. Use

• When the source equipment is connected with the u

“Off” when a connected piece of equipment is not

compatible or it is unclear whether the equipment is compatible or not.

“Off”.

details.

power consumption on standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

HDMI OUT MAIN instead.

connection, it may malfunction if “HDMI Control(RIHD)” is set to “On”.

■ HDMI Through

` Off ` Auto:

Detects the signal and automatically selects the input source.

` BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,

AUX, TV/CD, PHONO, PORT:

Selects the input source for which the HDMI Through function is enabled.

` Last:

The HDMI Through function is activated on the input source selected at the time of setting the AV

receiver to standby mode. When enabling the HDMI Through function, regardless of whether the AV receiver is on or in standby, both audio

and video streams from an HDMI input will be output to the TV or other components via HDMI connection. The HDMI indicators light when enabled (HDMI is dimlylit).

This setting is set to “Auto” automatically when the above “HDMI Control(RIHD)” is set to “On”.

p-compatible

” or “Recorder*”, etc (“*”

“On”, change the setting

Page 61

Note

• Only the input source assigned to the HDMI IN via “HDMI Input” is enabled (➔ page 44).

• The power consumption during standby mode will increase

during the HDMI Through function; however in the following cases, the power consumption can be saved: – The TV is in standby mode. – You are watching a TV program.

• Refer to the connected component’s instruction manual for

details.

• Depending on the connected component, the correct input source

may not be selected with the setting set to “Auto”.

• This setting is set to “Off” automatically when the “HDMI

Control(RIHD)” setting is set to “Off”.

■ Audio TV Out

` Off ` On

This preference determines whether the incoming audio signal is output from the HDMI output. You may want to turn this preference on if your TV is connected to the HDMI output and you want to listen to the audio from a connected component through your TV’s speakers. Normally, this should be set to “Off”.

Note

•If “On” is selected and the audio can be output from the TV, the AV receiver will output no sound through its speakers. In this case, “TV Speaker” appears on the display by pressing Display.

“HDMI Control(RIHD)” is set to “On”, this setting is

•When

“Auto”.

fixed to

• With some TVs and input signals, no sound may be output even when this setting is set to

•When “Audio TV Out” or

“On” and you’re listening through your TV’s speakers

(➔ page 17), turning up the AV receiver’s volume control will make the sound be output from the AV receiver’s front left and right speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

• Listening mode cannot be changed when this setting is set to “On” and the input source is not HDMI.

•If the “Monitor Out” setting is set to “Both(Main)” or “Both(Sub)” (➔ page 44) and if your TV connected to a priority output cannot output the audio, the sound will be heard from AV receiver’s speakers.

“On”.

“HDMI Control(RIHD)” is set to

■ Audio Return Channel

` Off ` Auto

: The audio signal from your TV tuner can be sent to the HDMI OUT MAIN of the AV receiver.

The audio return channel (ARC) function allows an ARC capable TV to send the audio stream to the HDMI OUT MAIN of the AV receiver. To use this function, you must select the TV/CD input selector and your TV must be ARC capable.

Note

• If you set “Audio Return Channel” to “Auto”, the “Audio Selector” settings of the TV/CD input selector will be

automatically switched to “ARC” (➔ page 57).

•The “Audio Return Channel” setting can be set only when the “HDMI Control(RIHD)” setting is set to “On”.

• This setting is set to “Auto” automatically when the “HDMI Control(RIHD)” is set to “On” for the first time.

■ Lip Sync

` Off ` On

This function allows the AV receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports HDMI Lip Sync.

• If the “Monitor Out” setting is set to “HDMI Main”, “Both(Main)” or “Both” (➔ page 44), the delay will be corrected in accordance with the monitor connected to HDMI OUT MAIN. On the other hand, if “HDMI Sub” or “Both(Sub)” is selected, the delay will be corrected in accordance with the monitor connected to HDMI OUT SUB.

After changing the settings of the “HDMI

Control(RIHD)”, “HDMI Through” or “Audio

Return Channel”

turn off the power on all connected pieces of equipment and then turn them on again. Refer to the user’s manuals for all connected pieces of equipment.

Auto Standby

■ Auto Standby

` Off ` On

When “Auto Standby” is set to “On”, the AV receiver will automatically enter standby mode if there is no operation for 30 minutes with no audio and no video signal input.

“Auto Standby” will appear on the display and OSD 30 seconds before the Auto Standby comes on.

Default setting: On (Australian models), Off (North

American models)

Note

On”, the Auto Standby function may activate itself

•Set to “ during playback with some sources.

•The Auto

Standby function does not work when Zone 2/3 is on.

Page 62

Network

After modifying the network settings, you must confirm the changes by executing “Save”.

This section explains how to configure the AV receiver’s network settings manually.

If your router’s DHCP server is enabled, you don’t need to change any of these settings, as the AV receiver is set to use DHCP to configure itself automatically by default (i.e., DHCP is set to “Enable”). If, however, your router’s DHCP server is disabled (you’re for example using static IP), you’ll need to configure these settings yourself, in which case, a knowledge of Ethernet networking is essential.

What’s DHCP?

DHCP (Dynamic Host Configuration Protocol) is used by routers, computers, the AV receiver, and other devices to automatically configure themselves on a network.

What’s DNS?

The DNS (Domain Name System) translates domain names into IP addresses. For example, when you enter a domain name such as www.onkyousa.com in your Web browser, before accessing the site, your browser uses DNS to translate this into an IP address, in this case

63.148.251.142.

■ MAC Address

This is the AV receiver’s MAC (Media Access Control) address. This address cannot be changed.

■ DHCP

` Enable ` Disable

This setting determines whether or not the AV receiver uses DHCP to automatically configure its IP Address, Subnet Mask, Gateway, and DNS Server settings.

Note

• If you select “Disable”, you must configure the “IP Address”, “Subnet Mask”, “Gateway”, and “DNS Server” settings yourself.

■ IP Address

` Class A:

“10.0.0.0” to “10.255.255.255”

` Class B:

“172.16.0.0” to “172.31.255.255”

` Class C:

“192.168.0.0” to “192.168.255.255” Enter a static IP address provided by your ISP. Most routers use Class C IP addresses.

■ Subnet Mask

Enter the subnet mask address provided by your ISP (typically 255.255.255.0).

■ Gateway

Enter the gateway address provided by your ISP.

■ DNS Server

Enter the DNS server address provided by your ISP.

■ Proxy URL

To use a Web proxy, enter its URL here.

■ Proxy Port

If you’re using a Web proxy, enter a proxy port number here.

■ Network Control

` Enable ` Disable

This setting enables or disables control over the network.

Note

• When set to “Enable”, the NET indicator is dimly-lit and the power consumption slightly increases in standby mode.

■ Control Port

` “49152” to “65535”

This is the network port used for control over the network.

Note

•When the “Network Control” setting is set to “Disable”, this setting is cannot be selected.

Firmware Update

See “Firmware Update” for the update procedure (➔ page 85).

Note

• Perform the firmware update only when such an announcement is posted on the Integra web site. Visit the Integra web site for the latest information.

• It takes maximum 60 minutes to complete the firmware update.

• When updating a firmware from a USB mass storage device, the AV receiver searches the device which is connected earlier during power on.

■ Version

Displays the current version of the firmware.

■ Receiver

` via NET:

Performs the firmware update via Internet. Check the network connection before updating.

` via USB:

Performs the firmware update from a USB device.

These settings allow you to update the AV receiver’s firmware. Do not shutdown the power of the AV receiver while updating.

■ Universal Port

` via NET:

Performs the firmware update via Internet. Check the network connection before updating.

` via USB:

Performs the firmware update from a USB device.

These settings allow you to update Onkyo dock’s firmware. Do not shutdown the power of the AV receiver while updating.

Note

• This update shall not be performed when no dock is connected to the UNIVERSAL PORT jack.

Page 63

Remote Controller Setup Lock Setup

Main menu Remote Controller Setup

Remote Mode Setup

See “Looking up for Remote Control Code” (➔ page 73).

Activities Setup

Via onscreen menu, you can specify what actions will be taken by the Easy macro command in the Easy macro mode (➔ page 42).

First, select the Activities (MY MOVIE, MY TV, or MY MUSIC) that you want to configure.

■ Source

` BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,

AUX, TUNER, TV/CD, PHONO, PORT, NET, USB

With this setting, you can choose the target input source of the Easy macro.

■ TV Power On

` Enable ` Disable

With this setting, you can specify whether or not to turn on your TV.

■ Source Power On

` Enable ` Disable

With this setting, you can specify whether or not to turn on the source component.

■ Receiver Power On

` Enable ` Disable

With this setting, you can specify whether or not to turn on the AV receiver.

■ Receiver Source Change

` Enable ` Disable

With this setting, you can specify whether or not to change the input source.

■ Source Play

` Enable ` Disable

With this setting, you can specify whether or not to start playback.

With this preference, you can protect your settings by locking the setup menus.

Main menu Lock Setup

■ Setup

` Locked ` Unlocked

When “Locked” is selected, the setup menus will be locked and you cannot change any setting.

Using the Audio Settings

You can change various audio settings from the Home menu (➔ page 40).

Press Receiver followed by Home.

Use q/w and Enter to select “Audio”, and then use

q/w/e/r to make the desired selection.

Note

you’re listening through your TV speakers.

Tone Control Settings

■ Bass

` –10dB to 0dB

You can boost or cut low-frequency sounds output from the front speakers.

■ Treble

` –10dB to 0dB

You can boost or cut high-frequency sounds output from the front speakers.

You can adjust the bass and treble for the front speakers, except when the Direct or THX listening mode is selected.

Operating on the AV receiver

Press Tone repeatedly to select either “Bass” or

“Treble”.

Use + and – to adjust.

Note

• This setting is not available when the multichannel Analog input is selected.

to +10dB in 2 dB steps.

Page 64

Speaker Levels

Late Night

■ Subwoofer Level

` –15.0dB to 0.0dB

to +12.0dB in 0.5 dB steps.

■ Center Level

` –12.0dB to 0.0dB

to +12.0dB in 0.5 dB steps.

You can adjust the volume of each speaker while listening to an input source.

These temporary adjustments are cancelled when the AV receiver is set to standby. To save the setting you made here, go to “Level Calibration” (➔ page 49) before setting the AV receiver to standby.

Note

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to “No” or “None” in “Speaker Configuration” (➔ page 47) cannot be adjusted.

Dolby Volume

■ Dolby Volume

See “Dolby Volume” of “Audio Adjust” (➔ page 51).

Note

• This setting cannot be used in either of the following cases: – Direct listening mode is selected. – the multichannel analog input is selected. – any of the THX listening modes is selected, with “Loudness

Plus” set to “On” or “Preserve THX Settings” set to “Yes” (➔ page 50).

• When “Dolby Volume” is set to “On”, the “Dynamic EQ” and “Dynamic Volume” settings of all input selectors are switched to “Off”.

■ Late Night

For Dolby Digital and Dolby Digital Plus sources, the options are:

` Off ` Low:

Small reduction in dynamic range.

` High:

Large reduction in dynamic range.

For Dolby TrueHD sources, the options are:

` Auto

: The Late Night function is set to “On” or “Off” automatically.

` Off ` On

Turn this setting on to reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.

Note

• The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options.

• The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “Off” when the AV receiver is set to standby. For Dolby TrueHD sources, it will be set to “Auto”.

Audyssey

■ Audyssey

See “Audyssey” in “Source Setup” (➔ page 52).

■ Dynamic EQ

See “Dynamic EQ” in “Source Setup” (➔ page 52).

■ Dynamic Volume

See “Dynamic Volume” in “Source Setup” (➔ page 53).

Note

• These technologies can be used when all the following conditions are met: – Room Correction and Speaker Setup is completed. Note that

“Audyssey” requires the “Audyssey MultEQ XT Full

Calibration” method. – Any listening mode other than Direct is selected. – A pair of headphones is not connected. – multichannel analog input is not selected.

• The setting is stored individually for each input selector.

•“Dynamic EQ” and “Dynamic Volume” cannot be selected when any of the THX listening modes is selected, with “Loudness Plus” set to “On” or “Preserve THX Settings” set to “Yes”.

• When “Dynamic EQ” is set to “On” or “Dynamic Volume” is set to anything else than “Off”, “Dolby Volume” will be switched to “Off”.

Page 65

Music Optimizer

Re-EQ

■ Music Optimizer

` Off ` On

Turn this setting on to enhance the sound quality of compressed music files. Use it with music files that use “lossy” compression, such as MP3.

Note

• The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals. The Music Optimizer is disabled when the Direct listening mode is selected.

• The setting is stored individually for each input selector.

•The M.Opt indicator will light (➔ page 9).

• This setting is not available when the multichannel Analog input is selected.

With the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing.

■ Re-EQ

` Off ` On

This function can be used with the following listening modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Multichannel, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS Express, DSD, Dolby EX, Dolby Pro Logic IIz Height, Dolby PLIIx Movie, DTS Neo:6 Cinema and 5.1-channel source + DTS Neo:6.

■ Re-EQ(THX)

` Off ` On

This function can be used with the following listening modes: THX Cinema, THX Surround EX, and THX Select2 Cinema.

Note

• Settings for the Re-EQ function are kept in each listening mode. In THX listening mode however, the setting will return to “On” when the AV receiver is turned off.

Page 66

Multi Zone

In addition to the main listening room, you can also enjoy playback in the other room, or as we call Multi Zone. And, you can select a different source for each room.

Making Multi Zone Connections

There are two ways you can connect Zone speakers:

1. Connect them directly to the AV receiver.

2. Connect them to an additional amplifier.

Connecting Your Zone 2 Speakers Directly to the AV receiver

This setup allows you to select different sources for Main room and Zone 2. This is called Powered Zone, as the Zone 2 speakers are powered by the AV receiver.

To use this setup, you must activate the Powered Zone 2 setting (➔ page 47).

Main room

AV receiver

Connecting the Zone Speakers to an Additional Amplifier

This setup allows 7.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2/3.

Main room

AV receiver

Zone 2

Receiver/

integrated amp

Zone 2

R L

Note

• With this setup, the volume of Zone 2 is controlled by the AV receiver.

• Powered Zone 2 cannot be used if “Speakers Type(Front)” is set to “Bi-Amp” (➔ page 47).

• When Powered Zone 2 is used, listening modes that require front high, front wide or surround back speakers are unavailable.

Zone 3

Receiver/

integrated amp

Note

• With the default settings, the Zone 2/3 volume must be set on the Zone 2/3 amplifier. If your Zone 2/3 amplifier has no volume control, change the setting so that you can set the Zone 2/3 volume on the AV receiver.

Page 67

Zone 2 Video Output

The AV receiver features a composite video output for connection to a TV in Zone 2, so you can enjoy both audio and video in that zone.

Main room

AV receiver

Zone 2

Note

• If you use the COMPONENT VIDEO ZONE 2 OUT, you must set the “Zone 2 Component Video Out” setting to “Yes” (➔ page 60).

•The COMPONENT VIDEO ZONE 2 OUT outputs video only

from components connected to component video inputs.

•The ZONE 2 OUT V jack outputs video from components

connected to composite video inputs.

Controlling Zone 2/3 Components

■ Operating on the AV receiver

Zone 2, Off

Zone 3, Off

Zone Level q/w

Tone

-, +

Input selector buttons

To turn on Zone 2/3 and select an input source,

press Zone 2 or Zone 3 followed by an input selector button within 8 seconds.

Zone 2/3 turns on, the Z2/3 indicator lights on the display.

Tip

• The corresponding trigger output goes high (+12 V).

To select AM or FM, press Tun er input selector and Zone 2 or Zone 3 repeatedly.

To select the same source as the main room’s, press Zone 2 or Zone 3 twice. “Z2 Selector: Source” or “Zone 3 Selector: Source” appears on the display.

To turn off Zone 2/3, press Zone 2 or Zone 3. The Z2/3 indicator on the display flash. Press Off.

The zone is turned off.

Tip

• The corresponding trigger output goes low (0 volts).

■ Operating on the remote controller

To control Zone 2/3, you must press the remote controller’s Zone first. Zone turns red while Zone 2 is on, and green while Zone 3 is on.

Note

• Zone 4 is not available for this model.

8Receiver

Zone

Input selector buttons

Muting

VOLq/w

Press Zone repeatedly, then point the remote

controller at the AV receiver and press 8Receiver.

Zone 2/3 turns on, the Z2/3 indicator lights on the display.

Tip

• The corresponding trigger output goes high (+12 V).

To select an input source for Zone 2/3, press Zone

repeatedly, followed by Input Selector.

To select AM or FM, press the Tun er input selector and Zone repeatedly.

Note

• You cannot select different AM or FM radio stations for your main room and Zone 2/3. The same AM/FM radio station will be heard in each room.

To turn off Zone 2/3, press Zone repeatedly,

followed by 8Receiver.

Tip

• The corresponding trigger output goes low (0 volts).

Page 68

Adjusting the Volume for Zones

■ Operating on the remote controller

press Zone repeatedly.

Use VOL q/w to adjust the volume.

■ Operating on the AV receiver

• The Zone 2 volume, tone, and balance function have no effect on ZONE 2 PRE/LINE OUT when the “Zone2 Out” setting is set to “Fixed” (➔ page 59).

• The Zone 3 volume function has no effect on ZONE 3 PRE/LINE OUT when the “Zone3 Out” setting is set to “Fixed” (➔ page 59).

• Even if you repeatedly press the remote controller’s Zone to select zones, the last zone selection will be retained once you have switched to other components by pressing other Remote Mode after pressing Zone.

Press Zone 2 or Zone 3 (the Z2/3 indicator on the

display flash).

Use Zone Level q/w within 8 seconds to adjust the

volume.

If your Zone 2/3 speakers are connected to a receiver or integrated amp in Zone 2/3, use its volume control to adjust the volume.

Muting Zones

■ Operating on the remote controller

Press Zone repeatedly, and then press Muting.

Tip

• To unmute, press Zone followed by Muting again. Zones can also be unmuted by adjusting the volume.

Adjusting the Tone and Balance of Zone 2

On the AV receiver, press Zone 2.

Press the AV receiver’s Tone repeatedly to select

“Bass”, “Treble” or “Balance”.

Use –/+ to adjust the bass, treble or balance.

• You can boost or cut the bass or treble from –10 dB to +10 dB in 2 dB steps.

• You can adjust the balance from 0 in the center to +10 dB to the right or +10 dB to the left in 2 dB steps.

Note

• Only analog input sources are output by the ZONE 2/3 PRE/LINE OUT and FRONT WIDE/ZONE 2 L/R terminals.

Digital input sources are not output. If no sound is heard when an input source is selected, verify that the source is connected to an analog input.

• While Zone 2/3 is on, u functions will not work.

• You cannot select different AM or FM radio stations for your main room and Zone 2/3. The same AM/FM radio station will be heard in each room. Namely, if you have selected an FM station for the main room, that station will also be output in Zone 2/3.

• When you have selected NET or USB as the input selector, the last selector selected will be set for Main room, Zone 2, and Zone 3.

• When Zone 2/3 is activated and its input selector is selected, the power consumption of standby mode slightly increases.

• When setting the AV receiver to standby mode while Zone 2/3

is active, the Z2/3 indicator is dimly lit.

Using the 12V Triggers

The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source. The triggers can be set so that they activate when a connected component is selected as the input source for the main room, Zone 2, Zone 3 or any combination of rooms. When triggered, the output from a 12V TRIGGER OUT goes high (+12 volts and 150 milliamperes max. at 12V TRIGGER OUT A; +12 volts and 25 milliamperes max. at 12V TRIGGER OUT B and C).

• See also “12V Trigger A/B/C Setup” (➔ page 59).

Hookup

• Use a miniplug cable to connect the AV receiver’s 12V TRIGGER OUT A, B, or C jack to the 12 V trigger

input on a connected component.

Page 69

Using the Remote Controller in Zone and Multiroom Control Kits

To control the AV receiver with the remote controller while you’re in Zone, you’ll need a commercially available multiroom remote control kit for each zone.

• Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV receiver’s remote sensor, such as when it’s

installed inside a cabinet.

Using a Multiroom Kit with Zone

Using a Multiroom Kit with a Cabinet

In this setup, the IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver located in the cabinet via the connecting block.

Connecting block

IR IN

A or B

IR receiver

In this setup, the IR receiver in Zone picks up the infrared signals from the remote controller and feeds them through to the AV receiver in the main room via the connecting block.

IR IN A or B

Connecting block

Remote controller

Main room Zone

Signal flow

IR receiver

The miniplug cable from the connecting block should be connected to the AV receiver’s IR IN A or B jack, as shown below. The IR IN A and B jacks are identical. Up to two IR receivers can be connected.

From the connecting block

Miniplug cable

Inside

cabinet

Signal flow

Remote controller

Using a Multiroom Kit with Other Components

In this setup, an IR emitter is connected to the AV receiver’s IR OUT jack and placed in front of the other component’s remote control sensor. Infrared signals received at the AV receiver’s IR IN A or B jack are fed through to the other component via the IR emitter. Signals picked up by the AV receiver’s remote control sensor are not output.

IR receiver

IR IN

A or B

IR OUT

Connecting block

AV receiver

IR Emitter

Remote controller

Other component

AV r ecei ver

Signal flow

The IR emitter should be connected to the AV receiver’s IR OUT jack, as shown below.

Miniplug cable

Other component

Remote control sensor

Emitter

Miniplug

IR Emitter

AV receiver

Signal flow

Page 70

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock

Using the Onkyo Dock

The Dock is sold separately. Models sold are different depending on the region.

For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.

UP-A1 Dock

With the UP-A1 Dock, you can easily play the music, photos, or movies stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound.

You can use the AV receiver’s remote controller to operate your iPod/iPhone.

■ System Function

The AV receiver may take several seconds to startup, so you might not hear the first few seconds of the first song.

Auto Power On

If you start iPod/iPhone playback while the AV receiver is on standby, the AV receiver will automatically turn on and select your iPod/iPhone as the input source.

Direct Change

If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically select your iPod/iPhone as the input source.

Using the AV receiver’s Remote Controller

You can use the AV receiver’s remote controller to control basic iPod/iPhone functions (➔ page 71).

■ Operating Notes

• Functionality depends on your iPod/iPhone model and generation.

• Before selecting a different input source, stop your iPod/iPhone playback to prevent the AV receiver from selecting the iPod/iPhone input source by mistake.

• If any accessories are connected to your iPod/iPhone, the AV receiver may not be able to select the input source properly.

• When connecting the UP-A1 Dock to the radio tuner UP-HT1 (North American models)/UP-DT1 (Australian models) with AUTO selected by the tuner’s Mode Selector switch, you can switch the input source between UP-A1 Dock and the tuner, by pressing Port repeatedly on the front panel.

• While your iPod/iPhone is in the UP-A1 Dock, its volume control has no effect. If you adjust your iPod/iPhone models volume control while it’s in the UP-A1 Dock, make sure it’s not set too high before you reconnect your headphones.

• The Auto Power On function will not work if you set your iPod/iPhone in the UP-A1 Dock while it is playing.

• When Zone 2/3 is turned on, you can’t use Auto Power On and Direct Change functions.

•The “Charge Mode” setting must be set to “On” to enable the Auto Power On and Direct Change functions (➔ page 57).

■ Using Your iPod/iPhone Alarm Clock

You can use the Alarm Clock function of your iPod/iPhone to automatically turn on your iPod/iPhone and the AV receiver at a specified time. The AV receiver’s input source will automatically be set to the Port selector.

Note

• To use this function, your iPod/iPhone must be in the UP-A1 Dock, and the UP-A1 Dock must be connected to the AV receiver.

• This function works only in Standard mode (➔ page 72).

• When you use this function, be sure to set the AV receiver’s volume control to a suitable level.

• When Zone 2/3 is turned on, you can’t use this function.

• This function doesn’t work when alarms sounds are set on your iPod/iPhone.

•The “Charge Mode” setting must be set to “On” to enable the Alarm Clock function (➔ page 57).

■ Charging Your iPod/iPhone Battery

When the UP-A1 Dock with docked iPod/iPhone is connected to the AV receiver, the battery of your iPod/iPhone is charged. Charging occurs when AV receiver is set to on or standby.

You can specify how the power is fed to your iPod/iPhone when the AV receiver is in standby mode (➔ page 57).

Note

• When the UP-A1 Dock with docked iPod/iPhone is connected, the power consumption on standby mode slightly increases.

Page 71

■ Status Messages

If either of the following messages is not displayed on the AV receiver’s display, check the connection to your iPod/iPhone.

• PORT Reading

The AV receiver is checking the connection with the dock.

• PORT Not Support

The AV receiver do not support the connected dock.

•PORT UP-A1

UP-A1 Dock is connected.

Note

• The AV receiver displays the message “UP-A1” for several seconds after recognizing the UP-A1.

RI Dock

With the RI Dock, you can easily play the music stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound, and watch iPod/iPhone slideshows and videos on your TV. In addition, the onscreen display (OSD) allows you to view, navigate, and select your iPod/iPhone model’s contents on your TV, and with the supplied remote controller, you can control your iPod/iPhone from the comfort of your sofa. You can even use the AV receiver’s remote controller to operate your iPod/iPhone.

Note

• Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (➔ page 74).

• Connect the RI Dock to the AV receiver with an u cable

(➔ page 20).

• Set the RI Dock’s RI MODE switch to “HDD” or

“HDD/DOCK”.

• Set the AV receiver’s Input Display to “DOCK” (➔ page 41).

■ System Function

System On

When you turn on the AV receiver, the RI Dock and iPod/iPhone turn on automatically. In addition, when RI Dock and iPod/iPhone are on, the AV receiver can be

turned on by pressing 8Source.

Auto Power On

If you press the remote controller’s 1 (Playback) while the AV receiver is on standby, the AV receiver will automatically turn on, select your iPod/iPhone as the input source, and your iPod/iPhone will start playback.

Direct Change

If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically switch to the input to which the RI Dock is connected.

Other Remote Controllers

You can use the remote controller that came with the AV receiver to control other iPod/iPhone functions. The available functionality depends on the AV receiver.

iPod/iPhone Alarm

If you use the Alarm function on your iPod/iPhone to start playback, the AV receiver will turn on at the specified time and select your iPod/iPhone as the input source automatically.

Note

• Linked operations do not work with video playback or when the alarm is set to play a sound.

• If you use your iPod/iPhone with any other accessories, iPod/iPhone playback detection may not work.

• This function works only in Standard mode (➔ page 72).

• The System On function may not work depending on the RI Dock.

■ Operating Notes

• Use the AV receiver’s volume control to adjust the playback volume.

• While your iPod/iPhone is inserted in the RI Dock, its volume control has no effect.

• If you do adjust the volume control on your iPod/iPhone while it’s inserted in the RI Dock, be careful that it’s not set too loud before you reconnect your headphones.

Note

• On the iPod with video and iPod nano (1st generation), the click wheel is disabled during playback.

Controlling Your iPod/iPhone

By pressing the Remote Mode that’s been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section. See “Entering Remote Control Codes” for details on entering a remote control code (➔ page 74). See the Dock’s instruction manual for more information.

UP-A1 Dock

Port is preprogrammed with the remote control code for

controlling a Dock via Universal Port. You can control your iPod/iPhone when “Port” is

selected as the input source.

RI Dock

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.

• 8Source may not work with a remote control code (without u). In this case, make an u connection and enter the remote control code 81993 (with u).

■ With the RI Control

Make an u connection and enter the remote control code 81993 (with u).

• Set the AV receiver’s Input Display to “DOCK” (➔ page 41).

■ Without the RI Control

You must enter the remote control code 82990 first (➔ page 75).

Page 72

Press the appropriate Remote Mode first.

✔: Available buttons

Onkyo Dock

b c

g h

Buttons

a 8Source

Top Menu

b c q/w/e/r, Enter

Playlist e/r

d 1, 3, 2, 5, 4,

7, 6

Repeat ✔✔

Random ✔✔

Display ✔

Muting ✔✔

Album +/–

h i VOL q/w

Menu ✔

Return ✔

Mode

UP-A1 Dock

✔

✔✔

✔

✔✔

✔

u Dock

• With some iPod/iPhone models, generations and RI Docks, certain buttons may not work as expected.

• For detailed operation of iPod/iPhone, please refer to the instruction manual of the RI Dock.

This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Also, your iPod/iPhone may not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod/iPhone is already on, it will remain on when the remote controller transmits the On command. Similarly, if your iPod/iPhone is already off, it will remain off when the remote controller transmits the Off command.

Top Menu works as the mode button when used with the DS-A2 RI Dock.

In Extended mode (see *7), e/r is used as the page jump button. This allows you to quickly locate your favorite songs even when such lists as the song or artist lists are very long.

In Extended mode (see *7), this button doesn’t work.

In Extended mode (see *7), Display is used to switch between song informations. In Standard mode (see *7), Display turns on backlight for a second.

Display turns on backlight for a second.

Press Mode to switch between the following modes:

Standard mode

Nothing is displayed on your TV. Contents are browsed and selected on your iPod/iPhone display.

Extended mode (Music)

The music contents (artists, albums, songs, and so on) are displayed on your TV, and you can browse and select them on screen.

Extended mode (Video)

The video contents (Movies, Music Videos, TV Shows, Video Podcasts or Rentals) are displayed on your TV, and you can browse and select them on screen.

Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod/iPhone from the RI Dock.

Note

• In Extended mode (see

), you cannot operate your iPod/iPhone directly.

), it may take some time to acquire the contents.

), the on-screen navigation menus only appear on a TV that is connected to the HDMI OUT MAIN.

Page 73

Controlling Other Components

You can use the AV receiver’s remote controller to control your other AV components, including those made by other manufacturers. This section explains how to enter the remote control code (with the default underlined) for a component that you want to control: DVD, TV, CD, etc.

“Learning Commands” for learning commands directly from another component’s remote controller (➔ page 77).

“Using Normal Macros” for programing Activities to perform a sequence of remote control actions

(➔ page 78).

Preprogrammed Remote Control Codes

The following Remote Mode buttons are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components.

For details on controlling these components, see the indicated pages.

BD/DVD

TV/CD

Port

Integra/Onkyo Blu-ray Disc player (➔ page 75) Integra/Onkyo CD player (➔ page 75) Onkyo Universal Port Option (➔ page 71)

Looking up for Remote Control Code

You can look up for an appropriate remote control code from the on-screen setup menu.

Note

• This can only be carried out using the on-screen setup menu.

Press Receiver followed by Setup.

The main menu appears on-screen.

Tip

• If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV.

Use q/w to select “Remote Controller Setup”, and

then press Enter.

Use q/w to select “Remote Mode Setup”, and then

press Enter.

Use q/w to select a remote mode, and then press

Enter.

The menu of category selection appears.

Use q/w to select a category, and then press Enter.

The panel for brand name input appears.

Use q/w/e/r to select a character, and then press

Enter.

Repeat this step for the first three characters of the brand name. When you have entered the 3rd character, select “Search” and press Enter. A list of brand names is retrieved.

Use q/w to select a brand, and then press Enter.

Go to step 8.

If you cannot find the brand name, use r to select “Search DB”, and then press Enter to access the database on the network.

The AV receiver accesses and searches the database. After searching, a list of the brand name appears.

Tip

• If you cannot access the database, a message “Cannot connect to database.” will appear. Press Enter to return

to the previous step.

• If the brand name is not found, use r to select “Not

Listed”, and then press Enter.

Use q/w to select “Search by model number (via

network)”, and then press Enter.

The model number input panel appears.

When you do NOT have a network connection or if you are not sure about the exact model, select “Skip”, and then press Enter.

If you select “Skip”, you will go to step 11.

Enter the model in a similar manner as in the case

of the brand name (step 6).

Tip

• After entering the 3rd character, press Enter to start searching.

• You cannot enter a space character.

Use q/w to select the model, and then press Enter.

If the model is not found, use r to select “Not Listed”, and then press

After searching is completed, a message for remote control code transfer will appear.

While pointing the remote controller at the AV

receiver’s transmitter, press Enter.

Input sensor

Enter.

Transmitter

15° off center (Left/Right/Up/Down)

Approx. 16 ft. (5 m)

Page 74

When you searched for the model, a message “Suc-

cessful” will appear. Now the transfer is successful!

Go to step 15.

When you did NOT search for the model, the following screen appears.

Push any key (except for arrow buttons and Enter) to see if the component responds.

Tip

• When category other than TV have been selected, the content is different.

• Asterisks in [***/***] mean the order of the candidate code and the total number of the codes for the brand.

If you can control component, press Receiver, use

q/w to select “Works”, and then press Enter.

If you cannot control component, press Receiver, use q/w to select “Doesn’t work (Retry)” and press

Enter.

The next code appears. Repeat from step 11.

Press Enter to transfer the determined code.

Transmitter

Input sensor

15° off center (Left/Right/Up/Down)

Approx. 16 ft. (5 m)

Entering Remote Control Codes

You’ll need to enter a code for each component that you want to control.

Look up the appropriate remote control code in the

separate Remote Control Codes list.

The codes are organized by category (e.g., DVD player, TV, etc.).

While holding down the Remote Mode to which

you want to assign a code, press and hold down Display (about 3 seconds).

The Remote Mode button lights.

Note

• Remote control codes cannot be entered for Receiver and Zone.

• Only TV remote control codes can be entered for TV.

• Except for Receiver, TV and Zone, remote control codes from any category can be assigned to the Remote Mode. However, these buttons also work as input selector buttons (➔ page 23), so choose a Remote Mode that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose TV/CD when entering its remote control code.

Within 30 seconds, use the number buttons to enter

the 5-digit remote control code.

Remote Mode button flashes twice. If the remote control code is not entered successfully, Remote Mode button will flash once slowly.

Press Enter.

You’ll return to the category selection menu. Press

Setup to end the remote mode setup.

Note

• Though the provided remote control codes are correct at the time of printing, they are subject to change.

Page 75

Remote Control Codes for Integra/Onkyo Components Connected via

Integra/Onkyo components that are connected via u are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

Make sure the Integra/Onkyo component is

connected with an u cable and an analog audio cable (RCA).

See “Connecting Integra/Onkyo u Components” for details (➔ page 20).

Enter the appropriate remote control code for

Remote Mode, referring to the previous section.

` 42157:

Onkyo cassette tape deck with u

` 81993:

Onkyo Dock with u

Press Remote Mode, point the remote controller

at the AV receiver, and operate the component.

Within 30 seconds, press Remote Mode again.

Remote Mode button flashes twice, indicating that the button has been reset.

Each of Remote Mode is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.

Note

• The learning command is also reset.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

While holding down Receiver, press and hold

down Home until Receiver lights (about 3 seconds).

Within 30 seconds, press Receiver again.

Receiver flashes twice, indicating that the remote controller has been reset.

Controlling Other Components

Controlling Integra/Onkyo components without u

If you want to control an Integra/Onkyo component by pointing the remote controller directly at it, or you want to control an Integra/Onkyo component that’s not connected

via u, use the following remote control codes:

` 30627:

Integra/Onkyo DVD player without u

` 71817:

Integra/Onkyo CD player without u

` 32900/33100/33500:

Integra/Onkyo Blu-ray Disc player

` 32901/33104/33504:

Integra/Onkyo HD DVD player

` 70868:

Onkyo MD recorder without u

` 71323:

Onkyo CD recorder without u

` 82990:

Onkyo Dock without u

Resetting Remote Mode Buttons

You can reset a Remote Mode to its default remote control code.

While holding down Remote Mode that you want

to reset, press and hold down Home until Remote Mode button lights (about 3 seconds).

By pressing the Remote Mode that’s been programmed with the remote control code for your component, you can control your component as described below.

For details on entering a remote control code for other components, see “Entering Remote Control Codes” (➔ page 74).

Controlling a TV

TV is preprogrammed with the remote control code for

controlling a TV that supports the p*1 (limited to some models). The TV must be able to receive remote

control commands via p and be connected to the AV receiver via HDMI. If controlling your TV via

p doesn’t work very well, program your TV’s remote control code into TV and use the TV remote mode to control your TV.

Use the following remote control codes:

` 11807/13100/13500:

TV with p

Controlling a Blu-ray Disc/DVD Player, HD DVD Player or DVD Recorder

BD/DVD is preprogrammed with the remote control code

for controlling a component that supports the p (limited to some models). The component must be able to

receive remote control commands via p and be connected to the AV receiver via HDMI.

Use the following remote control codes:

` 32910/33101/33501/31612:

Blu-ray Disc/DVD player with p

The p supported by the AV receiver is the CEC system control function of the HDMI standard.

Page 76

Press the appropriate Remote Mode first.

✔: Available buttons

Components

j k

Buttons

a 8Source b 8, Input,

TV VOL q/w

Guide ✔✔✔

Top Menu ✔

d q/w/e/r,

Enter

Setup ✔✔ ✔✔✔

e f 1, 3, 2, 5,

4, 7, 6

Repeat

Random

Mode Number: 1 to 9, 0 ✔✔ ✔✔✔

Number: +10

Display ✔✔ ✔✔✔

Muting ✔✔ ✔✔✔✔

CH +/– ✔✔ ✔✔

Disc +/– ✔✔

PREV CH ✔✔✔

Menu ✔

Return ✔✔ ✔✔

CLR ✔✔ ✔✔✔

DVD player/DVD recorder

Blu-ray Disc player

HD DVD player

VCR/PVR

Satellite receiver

Cable receiver

CD player/CD recorder

MD recorder

✔✔✔✔✔

✔

✔✔ ✔✔✔

✔✔✔✔

✔

*2*4✔*2✔*4

✔

*2*4

✔

*2*4✔*2✔*4

✔

*2*4✔*2✔*4

✔

*2✔*2

✔

✔✔ ✔

Cassette tape deck

✔

Note

• With some components, certain buttons may not work as expected, and some may not work at all.

When you press 8Source, the related component is turned on (or off).

The p function is not supported. The p supported by the AV receiver is the CEC system control function of the HDMI standard.

3 (Pause) functions as reverse playback.

These buttons function as colored buttons or A, B, C, D buttons.

Note

• See the “Controlling Your iPod/iPhone” about the operation of iPod/iPhone (➔ page 71).

Page 77

Learning Commands

The AV receiver’s remote controller can learn the commands of other remote controllers. By transmitting, for example, the Play command from your CD player’s remote controller, the supplied remote controller can learn it, and then reproduce the exact same command when its

1 is pressed in CD remote mode. This is useful when you’ve entered the appropriate remote

control code (➔ page 74) but some buttons don’t work as expected.

8Receiver

Remote

Mode

While holding down Remote Mode for the mode

in which you want to use the command, press and hold down 8Receiver until the Remote Mode

button lights (about 3 seconds).

On the supplied remote controller, press the

button to which you want to assign the new command.

Point the remote controllers at each other, within

about 4 inches (10 cm) apart, and then press and hold the button whose command you want to acquire until the Remote Mode button flashes.

If the command is learned successfully, the Remote Mode button flashes twice.

Note

• The following buttons cannot learn new commands:

8Receiver, All Off, My Movie, My TV, My Music, Remote Mode, Mode, Home.

• The remote controller can learn approximately 70 to 90 commands, although this will be less if commands that use a lot of memory are learned.

• Remote controller buttons such as Play, Stop, and Pause are preprogrammed with commands for controlling Integra/Onkyo CD players, cassette decks, and DVD players. However, they can learn new commands, and you can restore the preprogrammed commands at any time by resetting the remote controller (➔ page 75).

• To overwrite a previously acquire command, repeat this procedure.

• Depending on the remote controller that you are using, there may be some buttons that won’t work as expected, or even some remotes with which learning is impossible.

• Only commands from infrared remote controllers can be acquire.

• When the remote controller runs out of batteries, all commands acquired will be lost and will have to be learned all over again. Therefore, do not discard your other remote controllers.

■ Deleting Acquired Commands

1. While holding down Remote Mode for the mode

from which you want to delete a command, press and hold down TV until the Remote Mode button lights (about 3 seconds).

2. Press Remote Mode or the button from which you

want to delete the commands. The Remote Mode button flashes twice. When you press Remote Mode, all commands learned in that mode will be deleted.

C D

PRESET

TUNER INPUT MULTI-CH

PHONO

GROUP

MODE

SUR

Within about 4 inches (10 cm)

TU NER

INPUT SELECTOR

TAPE DVD

SLEEP DIMM ER

POWER

Supplied remote controller

To learn more commands, repeat steps 2 and 3.

Press any Remote Mode when you’ve finished. The Remote Mode button flashes twice.

VOLUME

ING

TONE

TEST

CH SEL

DISC

C D DVD

VIDEO-2

VIDEO-1

Page 78

Using Normal Macros

Running Macros

You can program the remote controller’s Activities to perform a sequence of remote control actions.

Example:

To play a CD you typically need to perform the following actions:

1. Press Receiver to select the Receiver remote controller mode.

2. Press 8Receiver to turn on the AV receiver.

3. Press TV/CD to select the TV/CD input source.

4. Press 1 to start playback on the CD player.

You can program Activities so that all four actions are performed with just one button press.

Making Macros

Each Activities can store one macro, and each macro can contain up to 32 commands.

All Off

My Movie, My TV, My Music

Receiver

Press My Movie, My TV, or My Music.

The commands in the macro are transmitted in the order in which they were programmed. Keep the remote controller pointed at the AV receiver until all of the commands have been transmitted.

Macros can be run at any time, regardless of the current remote controller mode.

Deleting Macros

While holding down Home, press and hold down

All Off until All Off lights (about 3 seconds). Press All Off again.

All Off flashes twice.

Note

• When Normal macros are deleted, Activities are restored to their default settings, namely the Easy macro commands (➔ page 42).

• When using Normal macros, Easy macros cannot be used, which includes changing the source components.

While holding down Receiver, press and hold

down My Movie, My TV, or My Music until My Movie, My TV, or My Music lights (about 3

seconds). Press the buttons whose actions you want to

program into the macro in the order you want them performed.

For the CD example above, you would press the following buttons: 8Receiver, TV/CD, 1.

When you’ve finished, press Activities again.

Activities button flashes twice. If you enter 32 commands, the process will finish

automatically.

Note

• Mode cannot be operated during the macro-making process.

• Once you assign new macro commands, the previously registered macro will no longer work. If you wish to retrieve it, you will have to reassign the commands with the macro-making.

Page 79

Appendix

Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit.

If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer from whom you purchased this unit.

To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press

8On/Standby. “Clear” will appear on the display and the AV receiver will enter standby mode.

Note that resetting the AV receiver will delete your radio presets and custom settings.

Receiver

Home

To reset the remote controller to its factory defaults, while holding down Receiver, press and hold down Home until Receiver button lights (about 3 seconds). Within 30 seconds, press Receiver again.

The on-screen menus appear only on a TV that is connected to the HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Power

■ Can’t turn on the AV receiver

Make sure that the power cord is properly plugged into the wall outlet.

Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.

■ The AV receiver turns off unexpectedly

The AV receiver will automatically enter standby mode when Auto Standby has been set and launches.

—

■ When the power is restored after a power

interruption, “CHECK SP WIRE” appears on the display

The protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact the dealer from whom you purchased this unit.

—

Audio

■ There’s no sound, or it’s very quiet

Make sure that the digital input source is selected properly.

Make sure that all audio connecting plugs are pushed in all the way.

Make sure that the inputs and outputs of all components are connected properly.

Make sure that the polarity of the speaker cables is correct, and that the bare wires are in contact with the metal part of each speaker terminal.

Make sure that the input source is properly selected. 23 Make sure that the speaker cables are not shorting. 13 Check the volume. The AV receiver is designed for

home theater enjoyment. It has a wide volume range, allowing precise adjustment.

If the MUTING indicator is flashing on the display, press the remote controller’s Muting to unmute the AV receiver.

While a pair of headphones is connected to the Phones jack, no sound is output from the speakers.

If there’s no sound from a DVD player connected to an HDMI IN, check the DVD player’s output settings, and be sure to select a supported audio format.

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer.

Make sure that none of the connecting cables are bent, twisted, or damaged.

Not all listening modes use all speakers. 35 Specify the speaker distances and adjust the

individual speaker levels. Make sure that the speaker setup microphone is not

still connected. The input signal format is set to “PCM” or “DTS”.

Set it to “Off”.

17-20

—

Page 80

■ Only the front speakers produce sound

When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.

In the Mono listening mode, only the front speakers output sound if the “Output Speaker” setting is set to “Left / Right”.

Check the Speaker Configuration. 47

■ Only the center speaker produces sound

If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

In the Mono listening mode, only the center speaker output sound if the “Output Speaker” setting is set to “Center”.

Make sure the speakers are configured correctly. 47

■ The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or Mono listening mode is selected, the surround speakers produce no sound.

Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode.

Make sure the speakers are configured correctly. 47

■ The center speaker produces no sound

When the Stereo or Mono listening mode is selected, the center speaker produces no sound.

In the Mono listening mode, only the front speakers output sound if the “Output Speaker” setting is set to “Left / Right”.

Make sure the speakers are configured correctly. 47

■ The front high, front wide and surround back

speakers produce no sound

Depending on the current listening mode, no sound may be produced by the front high, front wide and surround back speakers. Select another listening mode.

Depending on the sound source, the sound produced by the front high, front wide and surround back speakers may be weak.

Make sure the speakers are configured correctly. 47 While the “Powered Zone 2” setting is set to “Yes”,

playback in the main room is reduced to 5.1channels and the front high, front wide and surround back speakers produce no sound.

■ The subwoofer produces no sound

When you play a source material that contains no information in the LFE channel, the subwoofer produces no sound.

Make sure the speakers are configured correctly. 47

■ There’s no sound with a certain signal format

Check the digital audio output setting on the connected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

With some DVD-Video discs, you need to select an audio output format from a menu.

Depending on the input signal, some listening modes cannot be selected.

—

35–39

■ Can’t get 6.1/7.1 playback

If no surround back speakers, front wide and front high speakers are connected, or the Zone 2 speakers are being used, 6.1/7.1 playback is not possible.

Depending on the number of connected speakers, it is not always possible to select all of the listening modes.

—

35–39

■ The speaker volume cannot be set as required

Check to see if a maximum volume has been set. 58 If the volume level of each individual speaker has

been adjusted to high positive values, then the maximum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey MultEQ Room Correction and Speaker Setup has been performed.

31, 49

■ Noise can be heard

Using cable ties to bundle audio cables with power cords, speaker cables, and the like may degrade the audio performance, so refrain from doing it.

An audio cable may be picking up interference. Try repositioning your cables.

—

■ The Late Night function doesn’t work

Make sure the source material is Dolby Digital, Dolby Digital Plus, and Dolby TrueHD.

■ The analog multichannel input doesn’t work

Check the multichannel input connections. — Make sure that the multichannel input is selected. 57 Check the audio output settings on your source

component.

—

■ About DTS signals

When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback.

With some CD and LD players, you won’t be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

Playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

—

Page 81

■ The beginning of audio received by an HDMI IN

can’t be heard

Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately.

—

Video

■ There’s no picture

Make sure that all video connecting plugs are pushed in all the way.

Make sure that each video component is properly connected.

If your TV is connected to the HDMI output(s), set the “Monitor Out” setting other than “Analog”, and select “-----” in the “HDMI Input” to watch composite video, S-Video, and component video sources.

If your TV is connected to the COMPONENT

VIDEO MONITOR OUT, MONITOR OUT S, or MONITOR OUT V, set the “Monitor Out” setting

to “Analog”, and select “-----” in the “Component Video Input” to watch composite video and S-Video sources.

If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to either the HDMI output(s) or COMPONENT VIDEO MONITOR OUT.

If the video source is connected to a composite video input, your TV must be connected to the HDMI output(s) or the corresponding composite video output.

If the video source is connected to an HDMI input, you must assign that input to an input selector, and your TV must be connected to the HDMI output(s).

On your TV, make sure that the video input to which the AV receiver is connected is selected.

If the “Monitor Out” setting is set to “Both(Main)” or “Both(Sub)” while your TV is connected to a secondary HDMI output (not a primary HDMI output), the picture may not appear. In this case, change the setting to “Both”.

■ There’s no picture from a source connected to

an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is not guaranteed. In addition, video signals from a PC are not guaranteed.

When the “Monitor Out” setting is set to “Analog”, and the “Resolution” setting is set to anything other than “Through”, no video is output by the HDMI outputs.

When the resolution is set to any resolution not supported by the TV, no video is output from the HDMI outputs.

If the message “Resolution Error” appears on the AV receiver’s display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player.

■ The on-screen menus don’t appear

On your TV, make sure that the video input to which the AV receiver is connected is selected.

17, 18

44, 45

18, 44

17, 45

—

When the AV receiver is not connected to a TV via HDMI, onscreen menus are not displayed.

—

■ The on screen display does not appear

Depending on the input signal, the on screen display may not appear when the input signal from the

HDMI IN is output to a device connected to the HDMI OUT MAIN.

Tuner

■ Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna. — Move the AV receiver away from your TV or

computer. Listen to the station in mono. 28 When listening to an AM station, operating the

remote controller may cause noise. Passing cars and airplanes can cause interference. — Concrete walls weaken radio signals. — If nothing improves the reception, install an outdoor

antenna.

—

Remote Controller

■ The remote controller doesn’t work

Before operating this unit, be sure to press Receiver.

Make sure that the batteries are installed with the correct polarity.

Install new batteries. Don’t mix different types of batteries, or old and new batteries.

Make sure that the remote controller is not too far away from the AV receiver, and that there’s no obstruction between the remote controller and the AV receiver’s remote control sensor.

Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary.

If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed.

Make sure you’ve selected the correct remote controller mode.

When using the remote controller to control other manufacturers’ AV components, some buttons may not work as expected.

Make sure you’ve entered the correct remote control code.

Make sure to set the same ID on both the AV receiver and remote controller.

■ Can’t control other components

If it’s an Integra/Onkyo component, make sure that the u cable and analog audio cable are connected properly. Connecting only an u cable won’t be

enough. Make sure you’ve selected the correct remote

controller mode.

—

11, 75

—

11, 75

Page 82

For a proper operation of the remote controller as a cassette tape deck is connected to the TV/CD IN jack, or as an RI Dock is connected to the TV/CD IN, VCR/DVR IN or GAME IN jacks, you must set the input display accordingly.

If you cannot operate it, you will need to enter the appropriate remote control code.

To control another manufacturer’s component, point the remote controller at that component.

If none of the codes work, use the Learning function to learn the commands of the other component’s remote controller.

To control an Integra/Onkyo component that’s connected via u, point the remote controller at the

AV receiver. Be sure to enter the appropriate remote control code first.

To control an Integra/Onkyo component that’s not connected via u, point the remote controller at the

component. Be sure to enter the appropriate remote control code first.

The entered remote control code may not be correct. If more than one code is listed, try each one.

■ Can’t learn commands from another remote

controller

When learning commands, make sure that the transmitting ends of both remote controllers are pointing at each other.

Are you trying to learn from a remote controller that cannot be used for learning? Some commands cannot be learned, especially those that contain several instructions.

UP-A1 Dock for iPod/iPhone

■ There’s no sound

Make sure your iPod/iPhone is actually playing. — Make sure your iPod/iPhone is properly inserted in

the Dock. Make sure the UP-A1 Dock is connected to the

UNIVERSAL PORT jack on the AV receiver. Make sure the AV receiver is turned on, the correct

input source is selected, and the volume is turned up. Make sure the plugs are pushed in all the way. — Try resetting your iPod/iPhone. —

■ There’s no video

Make sure that your iPod/iPhone model’s TV OUT setting is set to On.

Make sure the correct input is selected on your TV or the AV receiver.

Some versions of the iPod/iPhone do not output video.

■ The AV receiver’s remote controller doesn’t

control my iPod/iPhone

Make sure your iPod/iPhone is properly inserted in the Dock. If your iPod/iPhone is in a case, it may not connect properly to the Dock. Always remove your iPod/iPhone from the case before inserting it into the Dock.

The iPod/iPhone cannot be operated while it’s displaying the Apple logo.

—

Make sure you’ve selected the right remote mode. 23 When you use the AV receiver’s remote controller,

point it toward your AV receiver. When connecting the UP-A1 Dock to the radio tuner

UP-HT1 (North American models)/UP-DT1 (Australian models) with AUTO selected with the tuner’s Mode Selector switch, you can switch the input source between the UP-A1 Dock and the tuner, by pressing Port repeatedly on the front panel.

If you still can’t control your iPod/iPhone, start playback by pressing your iPod/iPhone model’s Play button. Remote operation should then be possible.

Try resetting your iPod/iPhone. — Depending on your iPod/iPhone, some buttons may

not work as expected.

—

■ The AV receiver unexpectedly selects your

iPod/iPhone as the input source

Always pause iPod/iPhone playback before selecting a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks.

—

■ iPod/iPhone doesn’t work properly

Try reconnecting your iPod/iPhone. —

Recording

■ Can’t record

On your recorder, make sure the correct input is selected.

To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (VCR/DVR IN to VCR/DVR OUT).

—

Zone 2/3

■ There’s no sound

Only components connected to analog inputs can be played in Zone 2/3.

—

■ The Zone 2 speakers produce no sound

Powered Zone 2 cannot be used if “Speakers Type(Front)” is set to “Bi-Amp”.

To use the Zone 2 speakers, you must set the “Powered Zone 2” setting to “Yes ”.

Music Server and Internet Radio

■ Can’t access the server or Internet radio

Check the network connection between the AV receiver and your router or switch.

Make sure that your modem and router are properly connected, and make sure they are both turned on.

Make sure the server is up and running and compatible with the AV receiver.

Check the “Network” settings. 62

—

94, 96

Page 83

■ Playback stops while listening to music files on

the server

Make sure your server is compatible with the AV receiver.

If you download or copy large files on your computer, playback may be interrupted. Try closing any unused programs, use a more powerful computer, or use a dedicated server.

If the server is serving large music files to several networked devices simultaneously, the network may become overloaded and playback may be interrupted. Reduce the number of playback devices on the network, upgrade your network, or use a switch instead of a hub.

94, 96

—

■ Can’t connect to the AV receiver from a Web

browser

If you’re using DHCP, your router may not always allocate the same IP address to the AV receiver, so if you find that you can’t connect to a server or Internet radio station, recheck the AV receiver’s IP address on the “Network” screen.

Check the “Network” settings. 62

USB Device Playback

■ Can’t access the music files on a USB device

Make sure the USB device is plugged in properly. — The AV receiver supports USB devices that support

the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.

USB memory devices with security functions cannot be played.

—

Others

■ Standby power consumption

In the following cases, the power consumption in standby mode may reach up to a maximum of 75 W:

– You are using the Universal Port jack. –“Network Control” is set to “Enable” in the

“Network” setting.

–“HDMI Control(RIHD)” setting is set to “On”.

(Depending on the TV status, the AV receiver will enter standby mode as usual.)

–The “HDMI Through” setting is set to other than

“Off”.

18, 60, 62

■ How do I change the language of a multiplex

source

Use the “Multiplex” setting on the “Audio Adjust” menu to select “Main” or “Sub”.

■ The u functions don’t work

To use u, you must make an u connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally.

While Zone 2/3 is turned on, the u functions don’t work.

—

■ The functions System On/Auto Power On and

Direct Change don’t work for components connected via u

While Zone 2/3 is turned on, the u functions don’t work.

■ When performing “Automatic Speaker Setup”,

the measurement fails showing the message “Ambient noise is too high.”

This can be caused by a malfunction in your speaker unit. Check if the unit produces normal sounds.

—

■ The following settings can be made for the

S-Video and composite video inputs

You must use the buttons on the unit to make these settings.

On the AV receiver, press the input selector for the input source that you want to set and the

Setup button

simultaneously. While holding down the input selector button, press Setup until “Video ATT:On” appears on the display. Then, release both buttons. To reactivate the setting, repeat the above process so that “Video ATT:Off” appears on the display, and release the buttons.

•Video Attenuation

This setting can be made for the BD/DVD, VCR/DVR, CBL/SAT, Game or AUX input.

If you have a game console connected to the composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT:Off: (default). Video ATT:On: Gain is reduced by 2 dB.

■ The sound changes when I connect my

headphones

When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, or Direct.

—

■ The speaker distance cannot be set as required

In some cases, corrected values suitable for home theater use may be set automatically.

—

Page 84

■ If the picture on your TV/monitor connected to

the HDMI output(s) is unstable, try switching the DeepColor function off

To turn off the DeepColor function, simultaneously press the CBL/SAT and 8On/Standby buttons on the

AV receiver. While holding down CBL/SAT, press

8On/Standby until “Off” appears on the display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until “On” appears on the display and release the buttons.

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall outlet, set the AV receiver to standby.

Important Note Regarding Video Playback

The AV receiver can upconvert component video, SVideo, and composite video sources for display on a TV connected to the HDMI output(s). However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether.

In this case, try the following:

If the video source is connected to a component

video input, connect your TV to the COMPONENT VIDEO MONITOR OUT.

If the video source is connected to an S-Video input, connect your TV to a MONITOR OUT S.

If the video source is connected to a composite video input, connect your TV to the MONITOR OUT V.

On the main menu, select “Input/Output Assign”

and then “Component Video Input” (➔ page 46).

If the video source is connected to COMPONENT VIDEO IN 1, select the relevant input selector, and

assign it to “IN1”.

If the video source is connected to COMPONENT VIDEO IN 2, select the relevant input selector, and assign it to “IN2”.

If the video source is connected to COMPONENT VIDEO IN 3, select the relevant input selector, and assign it to “IN3”.

If the video source is connected to an S-Video input or composite video input, select the relevant input selector, and assign it to “-----”.

Note

• To by-pass the upconversion, set the “Picture Adjust” setting to “Direct” (➔ page 55).

Page 85

Firmware Update

To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully.

■ Update via network

You need a wired Internet connection to update the firmware.

■ Update via USB storage (➔ page 86)

Please prepare a USB storage device such as a USB flash memory stick. You need at least 32 MB of available space to update the firmware.

Note

• Check the network connection before updating.

• Do not touch the any cable or device connected to the AV receiver during the update process.

• Do not attempt to access the AV receiver from your PC while it is being updated.

• Do not shutdown the power of the AV receiver while it is being updated.

• The storage media in the USB card reader may not work.

• If the USB device is partitioned, each section will be treated as an independent device.

• If the USB device contains a lot of data, the AV receiver may take a while to read it.

• Operation is not guaranteed for all USB devices, which includes the ability to power them.

• Onkyo takes no responsibility whatsoever for the loss or damage of data resulting from the use of a USB device with the AV receiver. Onkyo recommends that you back up your important

music files beforehand.

• If you connect a USB hard disk drive to the USB port, Onkyo

recommends that you use its AC adapter to power it.

• USB hubs and USB devices with hub functions are not

supported. Do not connect your USB device via a USB hub.

• USB devices with security functions are not supported.

Limitation of liability

The program and accompanying online documentation are furnished to you for use at your own risk. Onkyo will not be liable and you will have no remedy for damages for any claim of any kind whatsoever concerning your use of the program or the accompanying online documentation, regardless of legal theory, and whether arising in tort or contract. In no event will Onkyo be liable to you or any third party for any special, indirect, incidental, or consequential damages of any kind, including, but not limited to, compensation, reimbursement or damages on account of the loss of present or prospective profits, loss of data, or for any other reason whatsoever.

See the Integra web site for latest information.

Updating the Firmware via Network

The AV receiver allows you to update the firmware using network connection on the rear panel.

Note

• Make sure your AV receiver and TV are turned on and an Ethernet cable is connected to the rear panel of the AV receiver.

• Never unplug or turn off the AV receiver while it is being updated.

• Never plug or unplug an HDMI or Ethernet cable during the update process.

• Do not attempt to access the AV receiver from your PC while it is being updated.

• Never unplug the power cord during the update process.

• It takes maximum 60 minutes to complete the firmware update.

• The AV receiver will retain all your settings after the update is finished.

Before you start

•Set the “HDMI Control(RIHD)” setting to “Off” (➔ page 60).

• Turn off the controller device connected via RS232C and via Ethernet network.

• Turn off Zone 2 and Zone 3.

• Stop playback of contents from Internet Radio, iPod/iPhone, USB or servers, etc.

Update procedure

Press Receiver followed by Setup on the remote

controller.

The Setup menu will be displayed on the TV screen. The procedures thereafter can also be performed on the AV receiver by using its Setup, arrow and Enter buttons.

Select “Hardware Setup” and press Enter.

Select “Firmware Update” and press Enter.

Note that the “Firmware Update” option will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable.

Select “via NET” and press Enter.

Select “Update” and press Enter.

The update process will begin. During the update process, the on-screen display

may disappear depending on the updated program. When this occurs, you can still view the update progress on the front display of the AV receiver. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again.

The message “Completed!” appears on the front

display of the AV receiver, indicating that the update has been completed.

Page 86

Using 8On/Standby on the front panel, turn off

and on the AV receiver.

Do not use 8Receiver on the remote controller. Congratulations! You now have the latest firmware

installed on your Integra AV receiver.

Troubleshooting

Case 1:

If “No Update” is displayed on the front display of the AV receiver, it means that the firmware has already been updated. You do not need to do anything further.

Case 2:

If an error occurs, “Error!! *-**” is displayed on the front display of the AV receiver. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action.

■ Errors during an update via network

Error Code Description

-10, *-20

-11, *-13, *-21,

-28

Others Retry the update procedure from the

The Ethernet cable was not detected. Reconnect the cable properly.

Internet connection error. Check the following items:

• Make sure the IP address, subnet mask, gateway address, and DNS server are configured properly.

• Make sure the router is turned on.

• Make sure the AV receiver and the router are connected with an Ethernet cable.

• Make sure your router is configured properly. See the instruction manual of the router.

• If your network allows only one client connection and there is any other device already connected, the AV receiver will not be able to access the network. Consult your Internet Service Provider (ISP).

• If your modem does not function as a router, you will need a router. Depending on your network, you may need to configure the proxy server if necessary. See the document provided by your ISP. If you are still unable to access the Internet, the DNS or proxy server may be temporarily down. Contact your ISP.

beginning. If the error persists, please contact Integra Support (➔ page 87) and provide the error code.

Case 3:

If an error occurs during the update process, disconnect then reconnect the AC power cord and try again.

Case 4:

If an error occurs due to a wrong selection of input sources, turn off and on the AV receiver. Then retry the update.

Case 5:

If you do not have an Internet connection, please contact Integra Support (➔ page 87).

Updating the Firmware via USB

The AV receiver allows you to update the firmware using a USB device.

Note

• Never unplug or turn off the AV receiver during the update process.

• Never plug or unplug an HDMI cable or a USB device during the update process.

• Never unplug the USB storage device containing the firmware file or the AC power cord during the update process.

• Do not attempt to access the AV receiver from your PC while it is being updated.

• It takes maximum 60 minutes to complete the firmware update.

• The AV receiver will retain all your settings after the update is finished.

Before you start

• Set the “HDMI Control(RIHD)” setting to “Off” (➔ page 60).

• Turn off the controller device connected via RS232C and via Ethernet network.

• Turn off Zone 2 and Zone 3.

• Stop playback of contents from Internet Radio, iPod/iPhone, USB or servers, etc.

• If there is any data in the USB device, remove it first.

Update procedure

Connect a USB device to your PC. If there is any

data in the USB device, remove it first.

Download the firmware file from the Integra web

site. The file name is as follows:

ONKAVR****_************.zip

Unzip the downloaded file. The following three files are created:

ONKAVR****_************.of1 ONKAVR****_************.of2 ONKAVR****_************.of3

Copy the extracted files to the USB device. Be

careful not to copy the zip file.

Remove the USB device from your PC and

connect it to the USB port on the AV receiver.

When the AV receiver has two USB ports, you can use either one.

Make sure the AV receiver and TV are turned on.

If the AV receiver is in standby mode, press 8On/Standby on the AV receiver to light up the

front display.

Select the USB input source.

“Now Initializing...” is displayed on the front display and then the name of the USB device is displayed. It takes 20 to 30 seconds to recognize the USB device.

Page 87

Press Receiver followed by Setup on the remote

controller.

The setup menu will be displayed on the TV screen. The procedures thereafter can also be performed on the AV receiver by using its Setup, arrow and Enter buttons.

Select “Hardware Setup” and press Enter.

Select “Firmware Update” and press Enter.

Select “via USB” and press Enter.

Select “Update” and press Enter.

The update process will begin. During the update process, the on-screen display may disappear depending on the updated program.

When this occurs, you can still view the update progress on the front display of the AV receiver. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again.

Do not turn off the AV receiver and do not remove the USB device during the update process.

The message “Completed!” appears on the front

display of the AV receiver, indicating that the update has been completed.

Using 8On/Standby on the front panel, turn off

the AV receiver and then remove the USB device.

Do not use 8Receiver on the remote controller. Congratulations! You now have the latest firmware

installed on your Integra AV receiver.

Troubleshooting

Case 1:

If “No Update” is displayed on the front display of the AV receiver, it means that the firmware has already been updated. You do not need to do anything further.

Case 2:

■ Errors during an update via USB

Error Code Description

-10, *-20

-14

Others Retry the update procedure from the

Case 3:

If an error occurs during the update, disconnect then reconnect the AC power cord and try again.

Case 4:

If an error occurs due to a wrong selection of input sources, turn off and on the AV receiver. Then retry the update.

The USB device was not detected. Make sure the USB flash memory or USB cable is properly connected to the USB port. If the USB storage device has its own power supply, use it to power the USB device.

The firmware file was not found in the root folder of the USB device, or the firmware file is for another model. Retry and download the file on the support page of the web site, following the on-site instructions. If the error persists, please contact Integra Support and provide the error code.

beginning. If the error persists, please contact Integra Support and provide the error code.

ONKYO SOUND & VISION CORPORATION

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

The Americas

Integra Division of ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET <http://www.integrahometheater.com/>

Europe

ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 <http://www.eu.onkyo.com/>

China, Hong Kong

ONKYO CHINA LIMITED Unit 1&12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung, N.T., Hong Kong Tel: 852-2429-3118 Fax: 852-2428-9039 <http://www.onkyochina.com/>

Asia, Oceania, Middle East, Africa

Please contact an ONKYO distributor referring to Onkyo SUPPORT site. <http://www.intl.onkyo.com/support/local_support/index.html>

Page 88

Connection Tips and Video Signal Path

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide.

The on-screen menus appear only on a TV that is connected to the HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Video Connection Formats

Video components can be connected by using any one of the following video connection formats: composite video, S-Video, PC IN (Analog RGB), component video or HDMI, the latter offering the best picture quality.

The AV receiver can upconvert and downconvert between video formats, depending on the “Monitor Out” setting (➔ page 44), which generally determines whether video signals are upconverted for the component video output or the HDMI output.

Tip

• For optimal video performance, THX recommends that video signals pass through the system without upconversion (e.g., component video input passing through to component video output).

• To by-pass the upconversion, set the “Picture Adjust” setting to “Direct” (➔ page 55).

■ “Monitor Out” set to “HDMI Main” or “HDMI Sub”

Video input signals flow through the AV receiver as shown, with composite video, S-Video, PC IN (Analog RGB) and component video sources all being upconverted for the HDMI output. Use these settings if you connect either the

HDMI OUT MAIN or HDMI OUT SUB of the AV receiver to your TV.

The composite video, S-Video and component video outputs pass through their respective input signals as they are.

Composite

AV receiver

Video Signal Flow Chart

Blu-ray Disc/DVD player, etc.

S-Video Component HDMI

PC IN

(Analog RGB)

MONITOR OUT

Composite

S-Video Component HDMI

TV, projector, etc.

■ “Monitor Out” set to “Both”, “Both(Main)” or “Both(Sub)”

Video input signals flow through the AV receiver as shown, with composite video, S-Video, PC IN (Analog RGB) and component video sources all being upconverted for both

Video Signal Flow Chart

Blu-ray Disc/DVD player, etc.

HDMI outputs. Use these settings if you connect both the

HDMI OUT MAIN and HDMI OUT SUB of the AV receiver to your TV.

The composite video, S-Video and component video outputs pass through their respective input signals as they are.

` Both: Video signals are output from both HDMI outputs

AV r ecei ver

Composite

S-Video Component

PC IN

(Analog RGB)

at the resolution supported by both TVs. You cannot select “Resolution” setting.

` Both(Main): Video signals are output from both HDMI

Composite S-Video Component

MONITOR OUT

outputs but HDMI OUT MAIN takes priority; depending on the resolution, video signals may not be output from HDMI OUT SUB.

TV, projector, etc

` Both(Sub): Video signals are output from both HDMI outputs but HDMI OUT SUB takes priority; depending on the

resolution, video signals may not be output from HDMI OUT MAIN.

Note

•The “Monitor Out” setting will be automatically switched to “Analog” (➔ page 44) if not connected to both outputs when “Both”

is selected or if not connected to a priority output when “Both(Main)” or “Both(Sub)” is selected.

HDMI

Page 89

■ “Monitor Out” set to “Analog”

Video input signals flow through the AV receiver as shown, with composite video, S-Video, and PC IN (Analog RGB) sources being upconverted for the component video output.

Use this setting if you connect the AV receiver’s COMPONENT VIDEO MONITOR OUT to your TV.Composite video is upconverted to S-Video and S-

Video is downconverted to composite video. Note that these conversions only apply to the MONITOR OUT V and S outputs, not the VCR/DVR OUT V and S outputs.

The composite video, S-Video and component video outputs pass through their respective input signals as they are. This signal flow also applies when the “Resolution” setting is set to “Through” (➔ page 45).

AV r ecei ver

Video Signal Flow Chart

Blu-ray Disc/DVD player, etc.

Composite

S-Video Component

PC IN

(Analog RGB)

MONITOR OUT

Composite S-Video Component

TV, projector, etc

For details, refer to “Video Resolution Chart” (➔ page 90).

HDMI

Video Signal Flow and the Resolution Setting

When the “Monitor Out” setting is set to “Analog” (➔ page 44), if the “Resolution” setting is set to anything other than “Through” (➔ page 45), the video signal flow will be as shown here, with composite video, S-Video, and PC IN (Analog RGB) sources being upconverted for the component video output.

The composite video, S-Video, and component video outputs pass through their respective analog input signals as they are. HDMI input signals are not output.

Audio Connection Formats

Audio components can be connected by using any of the following audio connection formats: analog, analog multichannel, optical, coaxial or HDMI.

When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals connected to an optical or coaxial digital input are not output by the analog VCR/DVR OUT.

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog.

Video Signal Flow Chart

Blu-ray Disc/DVD player, etc.

Composite

S-Video Component

PC IN

(Analog RGB)

AV r ecei ver

MONITOR OUT

Composite S-Video Component

TV, projector, etc

Audio Signal Flow Chart

Blu-ray Disc/DVD player, etc.

AV receiver

Multichannel

*1*

Optical

OUT

TV, projector, etc.

Depends on the “Audio TV Out” setting (➔ page 61).

This is possible when “Audio Return Channel” is set to “Auto” (➔ page 61), the TV/CD input selector is selected, and your TV is ARC capable.

Only the front L/R channels are output.

HDMI

HDMICoaxial Analog

HDMI Analog

*1*

Page 90

Video Resolution Chart

The following tables show how video signals at different resolutions are output by the AV receiver.

NTSC/PAL

Output

Input

HDMI 1080p ✔✔✔

1080i ✔✔✔✔✔

720p ✔✔✔✔✔

480p/576p ✔✔✔✔✔✔

480i/576i ✔✔✔✔✔✔✔

Component 1080p ✔✔✔

1080i ✔✔✔✔✔

720p ✔✔✔✔✔

480p/576p ✔✔✔✔✔✔

480i/576i ✔✔✔✔✔✔✔

S-Video

480i/576i ✔✔✔✔✔✔✔

Composite

PC IN (Analog RGB)

HDMI 4K

1080p/24 1080p 1080i 720p 480p/576p 480i/576i

✔✔✔✔✔✔

✔: Output

Output

Component S-Video

Composite

Input

1080p 1080i 720p 480p/576p 480i/576i 480i/576i

HDMI 1080p

1080i

720p

480p/576p

480i/576i

Component 1080p ✔

1080i ✔✔

720p ✔✔

S-Video

480p/576p

480i/576i

✔

✔✔

✔✔✔

Composite

PC IN (Analog RGB)

Available resolutions: [640 × 480 60 Hz], [800 × 600 60 Hz], [1024 × 768 60 Hz], [1280 × 1024 60 Hz]

Available resolutions: [3840 × 2160 24/25/30 Hz]

The output is limited to 480p/576p for an effective signal in the effect of copy protect.

PC IN (Analog RGB) input signal is output at 720p resolution when you select “Analog” in the “Monitor Out” setting

✔

(➔ page 44) and “Through” in the “Resolution” setting (➔ page 45).

The on-screen menus and superimposed menus are displayed via HDMI OUT MAIN.

Page 91

Using an RIHD-compatible TV, Player, or Recorder

p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Integra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various

components, however, operation with components other than p-compatible components cannot be guaranteed.

About p-compatible components

The following components are p-compatible (as of January 2011).

■ TV

• Toshiba REGZA-LINK compatible TV

•Sharp TV

■ Players/Recorders

• Onkyo and Integra p-compatible players

• Toshiba REGZA-LINK compatible players and recorders (only when used together with Toshiba REGZA-LINK compatible TV)

• Sharp players and recorders (only when used together with Sharp TV)

Models other than those mentioned above may have some interoperability if compatible with CEC, which is part of the HDMI Standard, but operation cannot be guaranteed.

Note

• For proper linked operations, do not connect more p- compatible components than the quantities specified below, to the HDMI input terminal. – Blu-ray Disc/DVD players: up to three. – Blu-ray Disc/DVD recorders/Digital Video Recorders: up to

three.

– Cable/Satellite Set-top boxes: up to four.

• Do not connect the AV receiver to the other AV receiver/AV

amplifier via HDMI.

• Proper linked operations are not guaranteed when more

p-compatible components than the above-mentioned quantities are connected.

Operations that can be performed with p connection

■ For p-compatible TV

The following linked operations are enabled by connecting the AV receiver to an p-compatible

TV.

• The AV receiver will enter standby mode when the power of the TV is turned to standby.

• You can set on the menu screen of the TV to either output the audio from the speakers connected to the AV receiver, or from the speakers of the TV.

• It is possible to output the video/audio coming from the antenna or from the input jack of the TV from the speakers connected to the AV receiver. (A connection such as optical digital cable or similar is required above the HDMI cable.)

• Input to the AV receiver can be selected with the remote controller of the TV.

• Operations such as volume adjustment or similar for the AV receiver can be performed from the remote controller of the TV.

■ For p-compatible players/recorders

The following linked operations are enabled by connecting the AV receiver to an p-compatible

player/recorder.

• When the playback is started on the player/recorder, input of the AV receiver will switch to the HDMI input of the player/recorder that is playing back.

• Operation of the player/recorder is possible using the remote controller supplied with the AV receiver.

Depending on the model used, not all operations may be available.

Page 92

■ How to connect and setup

Confirm the connecting and setting.

1. Connect the HDMI OUT MAIN jack to the HDMI input jack of the TV.

Blu-ray Disc/DVD player, etc.

HDMI connection

AV receiver

DIGITAL AUDIO connection (OPTICAL)

TV, projector, etc.

HDMI connection

2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable.

Note

• When the audio return channel (ARC) function is used with

an ARC capable TV, this connection is not necessary (➔ page 61).

3. Connect the HDMI output of the Blu-ray Disc/DVD player/recorder to the HDMI IN 1 jack of the AV receiver.

Note

• It is necessary to assign the HDMI input when connecting

the Blu-ray Disc/DVD player/recorder to other jacks (➔ page 45). Do not assign the components connected to the HDMI IN to the TV/CD input at this time. Appropriate CEC (Consumer Electronics Control) operation can not be guaranteed.

Change each item in the “HDMI” menu according

to the following settings:

• HDMI Control(RIHD): On

• Audio Return Channel (ARC): Auto

See details of each setting (➔ pages 60, 61).

Confirm the settings.

1. Turn on the power for all connected components.

2. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation.

3. Turn on the power of the Blu-ray Disc/DVD player/recorder.

4. Start playback on the Blu-ray Disc/DVD player/recorder, and verify the following.

• The AV receiver automatically turns on, and

selects the input to which the Blu-ray Disc/DVD player/recorder is connected.

• The TV automatically turns on, and selects the

input to which the AV receiver is connected.

5. Following the operating instructions of the TV, select “Use the TV speakers” from the menu screen of the TV, and confirm that the audio is output from the speakers of the TV, and not from the speakers connected to the AV receiver.

6. Select “Use the speakers connected from the AV receiver” from the menu screen of the TV, and confirm that the audio is output from the speakers connected to the AV receiver, and not from the TV speakers.

Note

• Perform the above operations when you use the AV

receiver for the first time, when the settings of each component are changed, when the main power of each component is turned off, when the power cable is disconnected from the power supply, or when there has been a power outage.

Operate with the remote controller.

For buttons that can be operated (➔ page 75).

Note

• Audio from DVD-Audio or Super Audio CD may not

output from the TV speakers. You will be able to output the audio from the TV speakers by setting the audio output of the DVD player to 2ch PCM. (It may not be possible depending on the player models.)

• Even if you set to output audio on the TV speakers, audio

will be output from the speakers connected to the AV receiver when you adjust the volume or switch the input on the AV receiver. To output audio from the TV speakers, redo the operations on the TV.

• In case of an p connection with u and u audio

control compatible components, do not connect the RI cable at the same time.

• On the TV, when you select anything other than the HDMI

jack to which the AV receiver is connected, the input on the AV receiver will be switched to “TV/CD”.

• The AV receiver will automatically power on in

conjunction when it determines it to be necessary. Even if the AV receiver is connected to an p compatible

TV or player/recorder, it will not power on if it is not necessary. It may not power on in conjunction when the TV is set to output audio from the TV.

• Linked functions with the AV receiver may not work

depending on the component model connected. In such cases, operate the AV receiver directly.

Page 93

About HDMI

Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, and multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.)

The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components can display the picture.

The AV receiver’s HDMI interface is based on the following: Audio Return Channel, 3D, x.v.Color, DeepColor, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM.

Supported Audio Formats

• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)

• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit)

• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio)

Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats.

About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital Content Protection) video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999.

HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to protect video content and requires a HDCP-compatible device to display the encrypted video.

DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open industry group’s objective is to address the industry’s requirements for a digital connectivity specification for highperformance PCs and digital displays.

Note

• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details.

, a copy-protection system for digital

Page 94

Network/USB Features

Connecting to the Network

The following diagram shows how you can connect the AV receiver to your home network. In this example, it’s connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in.

Internet radio

Modem

WAN

LAN

Computer or media server

Router

Network Requirements

■ Ethernet Network

For the best results, a 100Base-TX switched Ethernet network is recommended. Although it’s possible to play music on a computer that’s connected to the network wirelessly, playback may be unreliable, so it is recommended to use wired connections.

■ Ethernet Router

A router manages the network, data-routing and supplying of IP addresses. Your router must support the following:

• NAT (Network Address Translation). NAT allows several networked computers to access the Internet simultaneously via a single Internet connection. The AV receiver needs Internet access for Internet radio.

• DHCP (Dynamic Host Configuration Protocol). DHCP supplies IP addresses to the network devices, allowing them to configure themselves automatically.

• A router with a built-in 100Base-TX switch is recommended.

Some routers have a built-in modem, and some ISPs require you to use specific routers. Please consult your ISP or computer dealer if you’re unsure.

■ CAT5 Ethernet cable

Use a shielded CAT5 Ethernet cable (straight-type) to connect the AV receiver to your home network.

■ Internet Access (for Internet radio)

To receive Internet radio, your Ethernet network must have Internet access. A narrowband Internet connection (e.g., 56K modem, ISDN) will not provide satisfactory results, so a broadband connection is strongly recommended (e.g., cable modem, xDSL modem, etc). Please consult your ISP or computer dealer if you’re unsure.

Note

• To receive Internet radio with the AV receiver, your broadband Internet connection must be working and able to access the Web. Consult your ISP if you have any problems with your Internet connection.

• The AV receiver uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see “Network” (➔ page 62).

• The AV receiver does not support PPPoE settings, so if you have a PPPoE-type Internet connection, you must use a PPPoEcompatible router.

• Depending on your ISP, you may need to specify a proxy server to use Internet radio. If your computer is configured to use a proxy server, use the same settings for the AV receiver (➔ page 62).

Page 95

Server Requirements

USB Device Requirements

■ Server playback

The AV receiver can play digital music files stored on a computer or media server and supports the following technologies:

• Windows Media Player 11

• Windows Media Player 12

• Windows Media Connect 2.0

• DLNA-certified media server If the operating system of your computer is Windows

Vista, Windows Media Player 11 is already installed. Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft web site.

• The computer or media server must be on the same network as the AV receiver.

• Each folder may contain up to 20000 music files, and folders may be nested up to 16 levels deep.

Note

• Depending on the media server, the AV receiver may not recognize it, or may not be able to play its music files.

Minimum system requirements for Windows Media Player 11 on Windows XP

Operating system

Windows XP Home Edition (SP2), Windows XP Professional (SP2), Windows XP Tablet PC Edition (SP2), Update Rollup 2 for Windows XP Media Center Edition 2005 (KB900325), October 2006 Update Rollup for Windows XP Media Center Edition (KB925766)

Processor: 233 MHz Intel Pentium II, Advanced

Micro Devices (AMD), etc.

Memory: 64 MB Hard disk: 200 MB of free space Drive: CD or DVD drive Modem: 28.8 kbps Sound card: 16-bit sound card Monitor: Super VGA (800 x 600) Video card: 64 MB VRAM, DirectX 9.0b Software: Microsoft ActiveSync (only when

using a Windows Mobile-based Pocket PC or smartphone)

Web browser: Microsoft Internet Explorer 6 or

Netscape 7.1

■ Remote playback

• Windows Media Player 12

• DLNA-certified (within DLNA Interoperability Guidelines version 1.5) media server or controller device.

Setting varies depending on the device. Refer to your device’s instruction manual for details.

If the operating system of your personal computer is Windows 7, Windows Media Player 12 is already installed. For more information, see the Microsoft web site.

• USB mass storage device class (but not always guaranteed).

• FAT16 or FAT32 file system format.

• If the storage device has been partitioned, each section will be treated as an independent device.

• Each folder may contain up to 20,000 music files and folders, and folders may be nested up to 16 levels deep.

• USB hubs and USB devices with hub functions are not supported.

Note

• If the media you connect is not supported, the message “No Storage” will appear on the display.

• If you connect a USB hard disk drive to the AV receiver’s USB port, we recommend that you use its AC adapter to power it.

• The AV receiver supports USB MP3 players that support the USB Mass Storage Class standard, which allows USB devices to be connected to computers without the need for special drivers or software. Note that not all USB MP3 players support the USB Mass Storage Class standard. Refer to your USB MP3 player’s instruction manual for details.

• Protected WMA music files on an MP3 player cannot be played.

• Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB device when that device is used with the AV receiver. We recommend that you back up your important music files beforehand.

• MP3 players containing music files that are managed with special music software are not supported.

• Operation is not guaranteed for all USB devices, which includes the ability to power them.

• Do not connect your USB device via a USB hub. The USB device must be connected directly to the AV receiver’s USB port.

• If the USB device contains a lot of data, the AV receiver may take a while to read it.

• USB devices with security functions cannot be played.

Page 96

Supported Audio File Formats

For server playback and playback from a USB device, the AV receiver supports the following music file formats. Variable bit-rate (VBR) files are supported. However, playback time may not be display correctly.

Note

• With remote playback, the AV receiver does not support the following music file formats: FLAC and Ogg Vorbis.

• In the case of server playback, the below-mentioned file formats may not be played depending on the server type.

■ MP3 (.mp3 or .MP3)

• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3 format with a sampling rate of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and bitrates of between 8 kbps and 320 kbps. Incompatible files cannot be played.

■ WMA (.wma or .WMA)

WMA stands for Windows Media Audio and is an audio compression technology developed by Microsoft Corporation. Audio can be encoded in WMA format by using Windows Media

• WMA files must have the copyright option turned off.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, bitrates of between 5 kbps and 320 kbps, and WMA DRM are supported.

• WMA Pro/Voice formats are not supported.

■ WMA Lossless (.wma or .WMA)

• Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz are supported.

• Quantization bit: 16 bit, 24 bit

■ WAV (.wav or .WAV)

WAV files contain uncompressed PCM digital audio.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, and 96 kHz are supported.

• Quantization bit: 8 bit, 16 bit, 24 bit

■ AAC

(.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/ .3GP or .3G2)

AAC stands for MPEG-2/MPEG-4 Audio.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, 96 kHz and bitrates of between 8 kbps and 320 kbps are supported.

■ FLAC (.flac or .FLAC)

FLAC is a file format for lossless audio data compression.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, and 96 kHz are supported.

• Quantization bit: 8 bit, 16 bit, 24 bit

■ Ogg Vorbis (.ogg or .OGG)

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and

bitrates of between 48 kbps and 500 kbps are supported. Incompatible files cannot be played.

Player.

■ LPCM (Linear PCM)

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, and 96 kHz are supported.

• Quantization bit: 8 bit, 16 bit, 24 bit

Only for playback via network.

About DLNA

The Digital Living Network Alliance is an international, cross-industry collaboration. Members of DLNA develop a concept of wired and wireless interoperable networks where digital content such as photos, music, and videos can be shared through consumer electronics, personal computers, and mobile devices in and beyond the home. The AV receiver complies with the DLNA Interoperability Guidelines version 1.5.

Page 97

Specifications

Amplifier Section

Rated Output Power All channels: (North American)

Maximum Effective Output Power

Dynamic Power

IEC60268-Short-term maximum output power

THD+N (Total Harmonic Distortion+Noise)

Damping Factor 60 (Front, 1 kHz, 8 Ω) Input Sensitivity and Impedance (Unbalance)

Rated RCA Output Level and Impedance

Maximum RCA Output Level and Impedance

Phono Overload 70 mV (MM 1 kHz 0.5%) Frequency Response 5 Hz - 100 kHz/+1 dB, -3 dB (Direct mode) Tone Control Characteristics

Signal to Noise Ratio 110 dB (LINE, IHF-A)

Speaker Impedance 4 or 6 Ω - 16 Ω

135 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of

0.08% (FTC) 160 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.1% (FTC) 145 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.7% (FTC)

(Australian)

7 ch × 180 W at 6 ohms, 1 kHz, 1 ch driven of 1 % (IEC)

(Australian)

7 ch × 230 W at 6 ohms, 1 kHz, 1 ch driven (JEITA)

300 W (3 Ω, Front) 250 W (4 Ω, Front) 150 W (8 Ω, Front)

0.08% (20 Hz - 20 kHz, half power)

200 mV/47 kΩ (LINE)

2.5 mV/47 kΩ (PHONO MM)

200 mV/470 Ω (PRE OUT)

4.6 V/470 Ω (PRE OUT)

±10 dB, 50 Hz (BASS) ±10 dB, 20 kHz (TREBLE)

80 dB (PHONO MM, IHF-A)

Video Section

Input Sensitivity/Output Level and Impedance

1 Vp-p/75 Ω (Component and S-Video Y)

0.7 Vp-p/75 Ω (Component PB/CB, PR/CR)

0.25 Vp-p/75 Ω (S-Video C) 1 Vp-p/75 Ω (Composite)

Component Video Frequency Response

5 Hz - 100 MHz/+0 dB, -3 dB

Tuner Section

FM Tuning Frequency Range

(North American)

87.5 MHz - 107.9 MHz (Australian)

87.5 MHz - 108.0 MHz, RDS

AM Tuning Frequency Range

522/530 kHz - 1611/1710 kHz

Preset Channel 40

General

Power Supply (North American)

Power Consumption (North American) 7.5 A

No-sound Power Consumption

Stand-by Power Consumption

Dimensions (W × H × D)

Weight 17.9 kg (39.5 lbs.)

■ HDMI

Input IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, IN 7,

Output OUT MAIN, OUT SUB Video Resolution 1080p Audio Format Dolby TrueHD, DTS-HD Master Audio,

Supported 3D, Audio Return Channel, DeepColor,

■ Video Inputs

Component IN 1, IN 2, IN 3 S-Video BD/DVD, VCR/DVR, CBL/SAT, GAME Composite BD/DVD, VCR/DVR, CBL/SAT, GAME,

Analog RGB PC IN

■ Video Outputs

Component MONITOR OUT, ZONE 2 OUT S-Video MONITOR OUT, VCR/DVR OUT Composite MONITOR OUT, VCR/DVR OUT,

AC 120 V, 60 Hz

(Australian)

AC 220 - 240 V, 50/60 Hz

(Australian) 710 W

(North American)

95W

(Australian)

100W

(North American)

0.2 W

(Australian)

0.3 W

435 mm × 198.5 mm × 427.5 mm 17-1/8" × 7-13/16" × 16-13/16"

AUX INPUT

DVD-Audio, DSD

x.v.Color, LipSync, CEC (RIHD)

AUX

ZONE 2 OUT

■ Audio Inputs

Digital Optical: 2 (Rear), 1(Front)

Analog BD/DVD, VCR/DVR, CBL/SAT, GAME,

Multichannel Inputs 7.1

Coaxial: 3

PC, TV/CD, PHONO, AUX

Page 98

■ Audio Outputs

Analog VCR/DVR, PRE OUT, ZONE2 PRE/LINE

Analog Multichannel Pre Outputs

Subwoofer Pre Outputs

Speaker Outputs Main (L, R, C, SL, SR, SBL, SBR) + Front

Phones 1 (6.3 ø)

OUT, ZONE3 PRE/LINE OUT

Wide/ZONE2 (L, R) + Front High (L, R)

■ Others

Setup Mic 1 RS232 1 Universal Port 1 RI 1 USB 1 (Front)/1 (Rear) Ethernet 1 IR Input 2 IR Output 1 12 V Trigger Out 3

Specifications and features are subject to change without notice.

Page 99

Memo

Page 100

Integra Division of

18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com

Integra Division of

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

Integra Division of

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396

Integra Division of

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163

SN 29400740

Y1104-1

* 2 9 4 0 0 7 4 0 *

Integra DTR-50.3 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Important Safety Instructions

Precautions

Supplied Accessories

Features

Front & Rear Panels

Front Panel

Display

Rear Panel

Remote Controller

Controlling the AV Receiver

Connections

Connecting the AV Receiver

Connecting Your Speakers

About AV Connections

Connecting Components with HDMI

Connecting Your Components

Connecting a Recording Component

Connecting the Antennas

Connecting the Power Cord

Turning On & Basic Operations

Turning On/Off the AV Receiver

Turning On

Turning Off

Playback

Selecting the Language for the Onscreen Setup Menus

Playing the Connected Component

Controlling Contents of USB or Network Devices

Understanding Icons on the Display

Playing an iPod/iPhone via USB

Playing a USB Device

Listening to Internet Radio

Playing Music Files on a Server

Remote Playback

Listening to AM/FM Radio

Using Basic Functions

Using the Automatic Speaker Setup

Using the Listening Modes

Using the Home Menu

Using the Sleep Timer

Setting the Display Brightness

Displaying Source Information

Selecting Speaker Layout

Changing the Input Display

Muting the AV Receiver

Using Headphones

Using Easy Macros

Recording

Advanced Operations

Advanced Setup

On-screen Setup Menus

Common Procedures in Setup Menu

Input/Output Assign

Speaker Setup

Audio Adjust

Source Setup

Listening Mode Preset

Miscellaneous

Hardware Setup

Remote Controller Setup Lock Setup

Main menu Lock Setup

Using the Audio Settings

Multi Zone

Making Multi Zone Connections

Controlling Zone 2/3 Components

Using the 12V Triggers

Using the Remote Controller in Zone and Multiroom Control Kits

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock

Using the Onkyo Dock

Controlling Your iPod/iPhone

Controlling Other Components

Preprogrammed Remote Control Codes

Looking up for Remote Control Code

Entering Remote Control Codes

Resetting the Remote Controller