IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODELS: 61-772
61-774
The Service Information provides the following information:
•Precautions and safety information
•Specifications
•Performance test procedure
•Calibration and calibration adjustment procedure
•Basic maintenance (replacing the battery)
CAT.IV |
600V |
|
|
1000A |
|
|
HIV |
|
61-774 |
HOLD |
|
MFD |
||
|
V |
|
|
V |
|
|
Ω |
|
|
A |
|
MAX |
400A |
|
1000A OFF |
||
MIN |
||
|
True RMS |
|
PEAK |
|
0 |
10 |
20 |
30 |
40 |
COM VΩ
Form number: TM61772-4
Revision: 4. Date: May 2005
Form number TM61772-4 |
Rev 4 May 2005 |
TABLE OF CONTENTS |
|
Title |
Page |
|
|
Introduction |
1 |
Precautions and Safety Information |
1 |
Symbol Table |
1 |
TightSight™ Display Notes |
1 |
Safety Information |
2 |
Certifications and compliance |
2 |
Specifications |
3 |
General Specification |
3 |
Voltage Specifications |
4 |
Current Specifications |
4 |
|
|
Resistance Specifications |
4 |
Capacitance Specifications |
4 |
Continuity Specifications |
4 |
Performance Verification |
5/6 |
Calibration |
6/7 |
|
|
Calibration Reference Points |
8 |
Replacing the Battery |
9 |
Form number TM61772-4 |
Rev 4 May 2005 |
Page 1
Warning
To avoid shock or injury, do not perform the verification tests or calibration procedures described in this manual unless you are qualified to do so.
The information provided in this document is for the use of qualified personnel only.
Caution
The 61-770 series contains parts that can be damaged by static discharge. Follow the standard practices for handling static sensitive devices.
For additional information about IDEAL INDUSTRIES, INC. and its products, and services, visit IDEAL INDUSTRIES, INC. web site at: www.idealindustries.com
Use the meter only as described in the Users Manual. If you do not do so, the protection provided by the meter may be impaired. Read the “Safety Information” page before servicing this product. In this manual, a Warning identifies conditions and actions that pose hazard (s) to the user; a Caution identifies conditions and actions that may damage the meter or the test instruments.
The Symbols
The symbols used on the meter and in this manual are explained in Table A.
Table A Symbols
Symbol |
Description |
Symbol |
Indicator Lights |
|
Battery |
HI-V |
High Voltage Indicator |
|
>30 V indicator is on |
||
|
|
|
|
|
Cautionary or important |
|
Continuity indicator |
|
information in manual |
|
|
|
|
|
|
|
DangerRisk of electrical |
|
|
|
shock |
|
|
|
Double InsulationProtection |
|
|
|
Class II |
|
|
CAT III |
IEC Over-voltage Category III |
|
|
CAT IV |
IEC Over-voltage Category IV |
|
|
TightSight™ Display Notes:
Only AC/DC amps units of measure are displayed in the TightSight™ display since primary use is for viewing current measurements in tight locations. The display will show numerical values only for other functions. The main display is to be used to view units of measure for all other functions. The backlit of the TightSight™ display functions only in AC or DC current. For all other measurements, the backlit is disabled.
Form number TM61772-4 |
Rev 4 May 2005 |
Page 2
SAFETY
Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. To avoid potential hazards, use the product only as specified.
CAUTION.
These statements identify conditions or practices that could result in damage to the equipment or other property.
WARNING.
These statements identify conditions or practices that could result in personal injury or loss of life.
Specific precautions
Do not operate without covers. To avoid personal injury, do not apply any voltage or current to the product without the covers in place.
Electric overload. Never apply a voltage to a connector on the product that is outside the range specified for that connector.
Avoid electric shock. To avoid injury or loss of life, do not connect or disconnect probes or test leads while they are connected to a voltage source.
Do not operate in wet/damp conditions. To avoid electric shock, do not operate this product in wet or damp conditions.
Safety |
Designed to EN 61010-1, EN 61010-2-032, UL 61010B-1, |
||
UL 61010B-2-032 specifications |
|
||
|
|||
|
1000V DC Category III |
|
|
Input rating |
600V DC Category IV |
|
|
750V AC Category III |
|
||
|
|||
|
600V AC Category IV |
|
|
|
CAT IV: Outside and service entrance. |
|
|
Over voltage category |
CAT III: Distribution level mains, fixed installation. |
|
|
CAT II: Local level mains, appliances, and portable equipment. |
|||
|
|||
|
CAT I: Signal level, special equipment or parts of |
|
|
|
equipment, telecommunication, electronics. |
|
Form number TM61772-4 |
Rev 4 May 2005 |