LASERJET PRO 400 MFP
Repair Manual
M425
HP LaserJet Pro 400 MFP M425 Series
Repair Manual
Copyright and License
Trademark Credits
© 2012 Copyright Hewlett-Packard
Development Company, L.P.
Reproduction, adaptation, or translation
without prior written permission is
prohibited, except as allowed under the
copyright laws.
The information contained herein is subject
to change without notice.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
Part number: CF286-90979
Edition 1, 4/2012
Microsoft®, Windows®, Windows® XP,
and Windows Vista® are U.S. registered
trademarks of Microsoft Corporation.
Conventions used in this guide
TIP: Tips provide helpful hints or shortcuts.
NOTE: Notes provide important information to explain a concept or to complete a task.
CAUTION: Cautions indicate procedures that you should follow to avoid losing data or damaging
the product.
WARNING! Warnings alert you to specific procedures that you should follow to avoid personal
injury, catastrophic loss of data, or extensive damage to the product.
ENWW iii
iv Conventions used in this guide ENWW
Table of contents
1 Removal and replacement ................................................................................................ 1
Removal and replacement strategy ............................................................................................. 2
Electrostatic discharge ............................................................................................... 2
Required tools ........................................................................................................... 3
Types of screws ........................................................................................................ 3
Service approach ..................................................................................................................... 3
Before performing service .......................................................................................... 3
After performing service ............................................................................................. 4
Post-service test ......................................................................................................... 4
Print-quality test .......................................................................................... 4
Parts removal order ................................................................................................... 5
Removal and replacement procedures ........................................................................................ 6
Rollers ..................................................................................................................... 6
Multipurpose (MP) tray pickup roller ............................................................. 6
Multipurpose (MP) tray separation pad ......................................................... 6
Tray 2 and optional Tray 3 pickup roller ....................................................... 9
Tray 2 and optional Tray 3 separation pad ................................................. 10
Document feeder rollers ............................................................................ 11
Document feeder separation pad ............................................................... 12
Covers, scanner assembly, and control panel ............................................................. 13
Left cover ................................................................................................ 13
Scanner assembly .................................................................................... 13
Control panel .......................................................................................... 15
Right cover .............................................................................................. 17
Top cover ................................................................................................ 18
Rear cover, rear door, and feed assembly ................................................... 20
Cartridge door and front cover assembly .................................................... 22
Main assemblies ..................................................................................................... 25
Laser scanner assembly ............................................................................. 25
Registration assembly ............................................................................... 26
Fuser assembly and paper feed guide ......................................................... 28
Duplex drive assembly .............................................................................. 31
ENWW v
Solenoids ............................................................................................................... 34
Tray 1 solenoid ........................................................................................ 34
Duplex solenoid ....................................................................................... 35
Motors and fans ...................................................................................................... 37
Main motor ............................................................................................. 37
Fan ........................................................................................................ 39
Printed circuit-board assemblies (PCAs) ...................................................................... 41
Engine controller assembly (DC controller) PCA ............................................ 41
Universal serial bus (USB) PCA .................................................................. 46
Formatter PCA ......................................................................................... 48
Wireless PCA .......................................................................................... 48
Fax PCA ................................................................................................. 49
Power switch PCA .................................................................................... 50
Connecting PCA ...................................................................................... 51
Miscellaneous parts ................................................................................................. 52
Transfer roller .......................................................................................... 52
Multipurpose (MP) tray pickup gear assembly .............................................. 53
Document feeder assembly ........................................................................ 54
Optional paper feeder (Tray 3) ................................................................................. 55
Optional paper feeder right cover .............................................................. 56
Optional paper feeder driver PCA .............................................................. 56
Optional paper feeder paper sensor PCA ................................................... 57
2 Parts and diagrams ........................................................................................................ 61
Order parts by authorized service providers .............................................................................. 62
Order replacement parts .......................................................................................... 62
Related documentation and software ......................................................................... 62
Supplies part numbers ............................................................................................. 62
Whole-unit replacement part numbers ........................................................................ 62
How to use the parts lists and diagrams .................................................................................... 64
Assembly locations ................................................................................................................. 65
Main unit ............................................................................................................... 65
Optional paper feeder ............................................................................................. 66
Covers, panels, and doors ...................................................................................................... 68
Internal assemblies ................................................................................................................. 70
Scanner and document feeder ................................................................................................. 82
Input devices ......................................................................................................................... 84
500-sheet paper feeder ........................................................................................... 84
Paper feeder covers .................................................................................. 84
Paper feeder main body (1 of 2) ................................................................ 86
Paper feeder main body (2 of 2) ................................................................ 88
vi ENWW
Alphabetical parts list ............................................................................................................. 90
Numerical parts list ................................................................................................................ 94
Index ................................................................................................................................. 99
ENWW vii
viii ENWW
List of tables
Table 2-1 Order parts, accessories, and supplies .................................................................................... 62
Table 2-2 Related documentation and software ...................................................................................... 62
Table 2-3 Supplies part numbers ........................................................................................................... 62
Table 2-4 Whole-unit replacement part numbers ..................................................................................... 63
Table 2-5 Assembly locations: main unit ................................................................................................ 65
Table 2-6 Assembly locations: optional paper feeder .............................................................................. 66
Table 2-7 Covers, panels, and doors ..................................................................................................... 69
Table 2-8 Internal components (1 of 5) .................................................................................................. 71
Table 2-9 Internal components (2 of 5) .................................................................................................. 73
Table 2-10 Internal components (3 of 5) ................................................................................................ 75
Table 2-11 Internal components (4 of 5) ................................................................................................ 77
Table 2-12 Internal components (5 of 5) ................................................................................................ 79
Table 2-13 PCA locations .................................................................................................................... 81
Table 2-14 Scanner and document feeder ............................................................................................. 83
Table 2-15 Paper feeder covers ............................................................................................................ 85
Table 2-16 Paper feeder main body (1 of 2) .......................................................................................... 87
Table 2-17 Paper feeder main body (2 of 2) .......................................................................................... 89
Table 2-18 Alphabetical parts list ......................................................................................................... 90
Table 2-19 Numerical parts list ............................................................................................................. 94
ENWW ix
x ENWW
List of figures
Figure 1-1 Phillips and Pozidriv screwdriver comparison ............................................................................ 3
Figure 1-2 Parts-removal order ................................................................................................................ 5
Figure 1-3 Remove the MP tray roller ....................................................................................................... 6
Figure 1-4 Remove the MP tray separation pad (1 of 5) ............................................................................. 7
Figure 1-5 Remove the MP tray separation pad (2 of 5) ............................................................................. 7
Figure 1-6 Remove the MP tray separation pad (3 of 5) ............................................................................. 8
Figure 1-7 Remove the MP tray separation pad (4 of 5) ............................................................................. 8
Figure 1-8 Remove the MP tray separation pad (5 of 5) ............................................................................. 9
Figure 1-9 Remove the Tray 2 or Tray 3 pickup roller (1 of 2) .................................................................... 9
Figure 1-10 Remove the Tray 2 or Tray 3 pickup roller (2 of 2) ................................................................ 10
Figure 1-11 Remove the Tray 2 or Tray 3 separation pad ........................................................................ 10
Figure 1-12 Remove the document feeder rollers (1 of 2) ......................................................................... 11
Figure 1-13 Remove the document feeder rollers (2 of 2) ......................................................................... 11
Figure 1-14 Remove the document feeder separation pad (1 of 2) ............................................................ 12
Figure 1-15 Remove the document feeder separation pad (2 of 2) ............................................................ 12
Figure 1-16 Remove the left cover ......................................................................................................... 13
Figure 1-17 Remove the scanner assembly (1 of 2) ................................................................................. 14
Figure 1-18 Remove the scanner assembly (2 of 2) ................................................................................. 14
Figure 1-19 Remove the control panel (1 of 3) ........................................................................................ 15
Figure 1-20 Remove the control panel (2 of 3) ........................................................................................ 16
Figure 1-21 Remove the control panel (3 of 3) ........................................................................................ 16
Figure 1-22 Remove the right cover ....................................................................................................... 17
Figure 1-23 Remove the top-cover assembly (1 of 3) ............................................................................... 18
Figure 1-24 Remove the top-cover assembly (2 of 3) ............................................................................... 19
Figure 1-25 Remove the top-cover assembly (3 of 3) ............................................................................... 19
Figure 1-26 Remove the rear cover, rear door, and feed assembly (1 of 3) ................................................ 20
Figure 1-27 Remove the rear cover, rear door, and feed assembly (2 of 3) ................................................ 21
Figure 1-28 Remove the rear cover, rear door, and feed assembly (3 of 3) ................................................ 21
Figure 1-29 Remove the cartridge door assembly and front cover (1 of 4) .................................................. 22
Figure 1-30 Remove the cartridge door assembly and front cover (2 of 4)
Figure 1-31 Remove the cartridge door assembly and front cover (3 of 4) .................................................. 23
Figure 1-32 Remove the cartridge door assembly and front cover (4 of 4) .................................................. 24
.................................................. 23
ENWW xi
Figure 1-33 Remove the laser scanner assembly (1 of 2) .......................................................................... 25
Figure 1-34 Remove the laser scanner assembly (2 of 2) .......................................................................... 26
Figure 1-35 Remove the registration assembly (1 of 3) ............................................................................ 27
Figure 1-36 Remove the registration assembly (2 of 3) ............................................................................ 27
Figure 1-37 Remove the registration assembly (3 of 3) ............................................................................ 28
Figure 1-38 Remove the fuser (1 of 5) ................................................................................................... 29
Figure 1-39 Remove the fuser (2 of 5) ................................................................................................... 29
Figure 1-40 Remove the fuser (3 of 5) ................................................................................................... 30
Figure 1-41 Remove the fuser (4 of 5) ................................................................................................... 30
Figure 1-42 Remove the fuser (5 of 5) ................................................................................................... 31
Figure 1-43 Remove the duplex drive assembly (1 of 4) ........................................................................... 32
Figure 1-44 Remove the duplex drive assembly (2 of 4) ........................................................................... 32
Figure 1-45 Remove the duplex drive assembly (3 of 4) ........................................................................... 33
Figure 1-46 Remove the duplex drive assembly (4 of 4) ........................................................................... 33
Figure 1-47 Remove the Tray 1 pickup solenoid (1 of 2) .......................................................................... 34
Figure 1-48 Remove the Tray 1 pickup solenoid (2 of 2) .......................................................................... 35
Figure 1-49 Remove the duplex solenoid ............................................................................................... 36
Figure 1-50 Remove the main motor (1 of 4) .......................................................................................... 37
Figure 1-51 Remove the main motor (2 of 4) .......................................................................................... 38
Figure 1-52 Remove the main motor (3 of 4) .......................................................................................... 38
Figure 1-53 Remove the main motor (4 of 4) .......................................................................................... 39
Figure 1-54 Remove the fan (1 of 2) ...................................................................................................... 40
Figure 1-55 Remove the fan (2 of 2) ...................................................................................................... 40
Figure 1-56 Allow the engine controller assembly to cool ......................................................................... 41
Figure 1-57 Remove the engine controller assembly (1 of 9) ..................................................................... 42
Figure 1-58 Remove the engine controller assembly (2 of 9) ..................................................................... 42
Figure 1-59 Remove the engine controller assembly (3 of 9) ..................................................................... 43
Figure 1-60 Remove the engine controller assembly (4 of 9) ..................................................................... 43
Figure 1-61 Remove the engine controller assembly (5 of 9) ..................................................................... 44
Figure 1-62 Remove the engine controller assembly (6 of 9) ..................................................................... 44
Figure 1-63 Remove the engine controller assembly (7 of 9) ..................................................................... 45
Figure 1-
Figure 1-65 Remove the engine controller assembly (9 of 9) ..................................................................... 46
Figure 1-66 Remove the USB PCA (1 of 2) ............................................................................................. 47
Figure 1-67 Remove the USB PCA (2 of 2) ............................................................................................. 47
Figure 1-68 Remove the formatter ......................................................................................................... 48
Figure 1-69 Remove the wireless PCA ................................................................................................... 49
Figure 1-70 Remove the fax PCA .......................................................................................................... 49
Figure 1-71 Remove the power-switch PCA (1 of 3) ................................................................................. 50
Figure 1-72 Remove the power-switch PCA (2 of 3) ................................................................................. 51
Figure 1-73 Remove the power-switch PCA (3 of 3) ................................................................................. 51
64 Remove the engine controller assembly (8 of 9) ..................................................................... 45
xii ENWW
Figure 1-74 Remove the connecting PCA ............................................................................................... 52
Figure 1-75 Remove the transfer roller ................................................................................................... 53
Figure 1-76 Remove the paper-pickup-gear assembly .............................................................................. 54
Figure 1-77 Remove the document feeder (1 of 2) ................................................................................... 55
Figure 1-78 Remove the document feeder (2 of 2) ................................................................................... 55
Figure 1-79 Remove the optional paper feeder right cover ....................................................................... 56
Figure 1-80 Remove the optional paper feeder driver PCA (1 of 2) ........................................................... 57
Figure 1-81 Remove the optional paper feeder driver PCA (2 of 2) ........................................................... 57
Figure 1-82 Remove the optional paper feeder paper sensor PCA (1 of 3) ................................................. 58
Figure 1-83 Remove the optional paper feeder paper sensor PCA (2 of 4) ................................................. 58
Figure 1-84 Remove the optional paper feeder paper sensor PCA (3 of 4) ................................................. 59
Figure 1-85 Remove the optional paper feeder paper sensor PCA (4 of 4) ................................................. 59
Figure 2-1 Assembly locations: main unit ............................................................................................... 65
Figure 2-2 Assembly locations: optional paper feeder ............................................................................. 66
Figure 2-3 Covers, panels, and doors ................................................................................................... 68
Figure 2-4 Internal components (1 of 5) ................................................................................................. 70
Figure 2-5 Internal components (2 of 5) ................................................................................................. 72
Figure 2-6 Internal components (3 of 5) ................................................................................................. 74
Figure 2-7 Internal components (4 of 5) ................................................................................................. 76
Figure 2-8 Internal components (5 of 5) ................................................................................................. 78
Figure 2-9 PCA locations ..................................................................................................................... 80
Figure 2-10 Scanner and document feeder ............................................................................................ 82
Figure 2-11 Paper feeder covers ........................................................................................................... 84
Figure 2-12 Paper feeder main body (1 of 2) ......................................................................................... 86
Figure 2-13 Paper feeder main body (2 of 2) ......................................................................................... 88
ENWW xiii
xiv ENWW
1 Removal and replacement
Removal and replacement strategy
●
Service approach
●
Removal and replacement procedures
●
ENWW 1
Removal and replacement strategy
WARNING! Turn the product off, wait 5 seconds, and then remove the power cord before
attempting to service the product. If this warning is not followed, severe injury can result, in addition to
damage to the product. The power must be on for certain functional checks during problem solving.
However, the power supply should be disconnected during parts removal.
Never operate or service the product with the protective cover removed from the laser/scanner
assembly. The reflected beam, although invisible, can damage your eyes.
The sheet-metal parts can have sharp edges. Be careful when handling sheet-metal parts.
CAUTION: Do not bend or fold the flat flexible cables (FFCs) during removal or installation. Also, do
not straighten pre-folds in the FFCs. You must Make sure that all FFCs are fully seated in their
connectors. Failure to fully seat an FFC into a connector can cause a short circuit in a PCA.
NOTE: To install a self-tapping screw, first turn it counterclockwise to align it with the existing thread
pattern, and then carefully turn it clockwise to tighten. Do not overtighten. If a self-tapping screw-hole
becomes stripped, repair the screw-hole or replace the affected assembly.
Electrostatic discharge
CAUTION: Some parts are sensitive to electrostatic discharge (ESD). Look for the ESD reminder
when removing product parts. Always perform service work at an ESD-protected workstation or mat. If
an ESD workstation or mat is not available, ground yourself by touching the sheet-metal chassis before
touching an ESD-sensitive part.
Protect the ESD-sensitive parts by placing them in ESD pouches when they are out of the product.
2 Chapter 1 Removal and replacement ENWW
Required tools
#2 Phillips screwdriver with a magnetic tip and a 152 mm (6 in) shaft length
●
Small flatblade screwdriver
●
Needle-nose pliers
●
ESD mat (if one is available) or ESD strap
●
Penlight (optional)
●
CAUTION: Always use a Phillips screwdriver (callout 1). Do not use a Pozidriv® screwdriver
(callout 2) or any motorized screwdriver. These can damage screws or screw threads.
Figure 1-1 Phillips and Pozidriv screwdriver comparison
CAUTION: Avoid pulling directly on wires to disconnect wire-harness connectors. Pull on the plastic
body of a connector to avoid damaging the connector wires.
Types of screws
WARNING! Make sure that components are replaced with the correct screw type. Using the
incorrect screw (for example, substituting a long screw for the correct shorter screw) can cause damage
to the product or interfere with product operation. Do not intermix screws that are removed from one
component with the screws that are removed from another component.
For a complete list of screw types and part numbers, see the Parts chapter.
Service approach
Before performing service
Remove all paper from the product.
●
Turn off the power using the power switch.
●
Unplug the power cable and interface cable or cables.
●
ENWW
Place the product on an ESD workstation or mat, or use an ESD strap (if one is available). If an
●
ESD workstation, mat, or strap is not available, ground yourself by touching the sheet-metal
chassis before touching an ESD-sensitive part.
Service approach
3
Remove the toner cartridge.
●
Remove the Tray 2 cassette.
●
After performing service
Plug in the power cable.
●
Reinstall the toner cartridge.
●
Reinstall the Tray 2 cassette.
●
Load paper in the product.
●
Post-service test
Perform the following test to verify that the repair or replacement was successful.
Print-quality test
1. Verify that you have completed the necessary reassembly steps.
2. Make sure that the tray contains clean, unmarked paper.
3. Attach the power cord and interface cable or interface cables, and then turn on the product.
4. Verify that the expected startup sounds occur.
5. Print a configuration page, and then verify that the expected printing sounds occur.
6. Print a demo page, and then verify that the print quality is as expected.
7. Send a print job from the host computer, and then verify that the output meets expectations.
8. Clean the outside of the product with a damp cloth.
4 Chapter 1 Removal and replacement ENWW
Parts removal order
Use the following diagram to determine which parts must be removed before removing other parts.
Figure 1-2 Parts-removal order
Toner cartridge
Tray 2 cassette
Tray 1 pickup roller
Tray 1 separation pad Left cover
Tray 1 pickup gear assembly Lef t cover
Tray 2/3 pickup roller Tray 2/3 cassette
Tray 2/3 separation roller Tray 2/3 cassette
Document feeder pickup rollers
Document feeder separation pad
Transfer roller Toner cartridge
Left cover Tray 2 cassette
Scanner assembly Left cover
Control panel Left cover Scanner assembly
Right cover Left cover Scanner assembly Control panel
Top cover Left cover Scanner assembly Control panel Right cover
Rear cover and feed assembly Left cover Scanner assembly Control panel Right cover
Cartridge door and
front cover assembl
Document feeder assembly Left cover Scanner assembly
Laser scanner assembly Left cover Scanner assembly Control panel Right cover Top cover
Registration roller assembly Left cover Scanner assembly Control panel Right cover Rear cover
Fuser assembly
and paper feed guide
Duplex drive assembly Left cover Scanner assembly Control panel Right cover Top cover
Tray 1 solenoid Left cover
Tray 2 solenoid Left cover Scanner assembly Control panel Right cover
Duplex solenoid Left cover Scanner assembly Control panel Right cover Rear cover
Main motor Left cover Scanner assembly Control panel Right cover Rear cover
Fan Left cover Scanner assembly Control panel Right cover Top cover
Engine controller unit (ECU) PCA Left cover Scanner assembly Control panel Right cover Rear cover
Formatter PCA Left cover Wireless PCA
USB PCA Left cover
Wireless PCA (wireless models) Left cover
Fax PCA Left cover
Power switch PCA Left cover Scanner assembly Control panel Right cover Front cover
Connecting PCA Left cover Scanner assembly Control panel Right cover
Optional paper feeder right cover
Optional paper feeder driver PCA Tray 3 right cover
Optional paper feeder
Component Remove Remove Remove Remove Remove Remove Remove Remove
er sensor PCA
Left cover Scanner assembly Control panel Right cover
and feed
Left cover Scanner assembly Control panel Right cover Rear cover
(wireless models)
Tray 3 right cover
assembly
and feed
and feed
assembly
and feed
assembl
and feed
assembly
assembl
Top cover
Top cover Fan Duplex drive
Top cover Fuser ECU
Top cover
assembly
ENWW
Service approach
5
Removal and replacement procedures
Rollers
Multipurpose (MP) tray pickup roller
1. Open the toner cartridge door, and then remove the toner cartridge.
2. Pull back and hold the pickup roller cover (callout 1), press the tabs (callout 2) on both ends of the
pickup roller away from the roller — which should cause the roller to move up — and then remove
the roller.
Figure 1-3 Remove the MP tray roller
1
2
Multipurpose (MP) tray separation pad
To remove the separation pad, you must first remove the pickup roller assembly.
1. Remove the following components:
Tray 2 cassette
●
Left cover. See
●
2. Open the toner cartridge door, and then remove the toner cartridge.
Left cover on page 13.
6 Chapter 1 Removal and replacement ENWW
3. On the left side of the product, release the tab (callout 1) at the center of the gear, and then
remove the gear (callout 2).
NOTE: The gear is composed of two pieces. Releasing the outer tab does not remove the entire
gear assembly and exposes an internal spring in the gear.
Figure 1-4 Remove the MP tray separation pad (1 of 5)
1
2
3
Reinstallation tip Press and hold back the gear arm (callout 3) when reinstalling the pickup
gear.
4. In the toner cartridge cavity, pull back the pickup roller cover, and then use a small flat-blade
screwdriver to release the tab (callout 1) on the pickup roller shaft.
Figure 1-5 Remove the MP tray separation pad (2 of 5)
1
ENWW
Removal and replacement procedures
7
5. Move the pickup roller shaft to the left to free the right end of the shaft from the holder, and then
remove the pickup roller shaft assembly to expose the separation pad.
Figure 1-6 Remove the MP tray separation pad (3 of 5)
Reinstallation tip The spring at the right end of the shaft is not captive and might fall off
during this process. Make sure that the spring is positioned correctly when reinstalling, as shown
in the following figure.
Figure 1-7 Remove the MP tray separation pad (4 of 5)
8 Chapter 1 Removal and replacement ENWW
6. Pull up on the top edge of the separation pad to release it from the product.
Figure 1-8 Remove the MP tray separation pad (5 of 5)
Reinstallation tip When reinstalling the pickup roller shaft assembly, make sure that the flat
part of the pickup roller is directly over the separation pad.
Tray 2 and optional Tray 3 pickup roller
1. Remove the tray cassette from the product.
2. Locate the pickup roller at the top of the cassette cavity. On the left roller holder, release the tab
(callout 1), and then turn the holder away from you.
Figure 1-9 Remove the Tray 2 or Tray 3 pickup roller (1 of 2)
1
ENWW
Removal and replacement procedures
9
3. Push the pickup roller to the left to release the right side roller, and then pull the roller out of the
product.
Figure 1-10 Remove the Tray 2 or Tray 3 pickup roller (2 of 2)
Tray 2 and optional Tray 3 separation pad
1. Remove the tray cassette from the product.
2. Locate the separation pad at the front of the cassette. On the separation pad, remove two screws
(callout 1), and then remove the pad from the tray cassette.
Figure 1-11 Remove the Tray 2 or Tray 3 separation pad
1
10 Chapter 1 Removal and replacement ENWW
Document feeder rollers
1. Open the document feeder cover.
Figure 1-12 Remove the document feeder rollers (1 of 2)
2. On the underside of the document feeder cover, use a small flat-blade screwdriver to release the
tabs (callout 1) on the left side of each roller, and then pull the rollers out of the cover.
Figure 1-13 Remove the document feeder rollers (2 of 2)
1
ENWW
Removal and replacement procedures
11
Document feeder separation pad
1. Open the document feeder cover.
Figure 1-14 Remove the document feeder separation pad (1 of 2)
2. Locate the separation pad at the end of the document feeder input tray, press down on the pad,
and then slide the pad toward the input tray to remove it from the assembly.
Figure 1-15 Remove the document feeder separation pad (2 of 2)
12 Chapter 1 Removal and replacement ENWW
Covers, scanner assembly, and control panel
Left cover
NOTE: No tools are necessary to remove this cover. However, a small flat-blade screwdriver might
be helpful in releasing some of the tabs that hold the cover to the product chassis.
1. Remove the Tray 2 cassette.
2. Open the toner cartridge door and the rear jam access door.
3. Grasp the front edge of the cover, and then pull the cover toward the front to release four of the
seven tabs (callout 1), and then release the two tabs at the top of the cover.
Figure 1-16 Remove the left cover
4. With the top and front edges loose, tip the top of the cover away from the product and then
carefully slide the cover toward the back of the product to remove it.
Scanner assembly
1. Remove the following components:
Tray 2 cassette
●
Left cover. See
●
2. Open the toner cartridge door and the rear jam access door.
1
Left cover on page 13.
ENWW
Removal and replacement procedures
13
3. On the left side of the product, remove the ground-wire screw (callout 1), disconnect one wire
connector (callout 2) on the formatter, and disconnect two flat, flexible cables (callout 3) on the
formatter.
Figure 1-17 Remove the scanner assembly (1 of 2)
1
2
3
Reinstallation tip Do not lose the two protective guides installed on the flat, flexible cables.
Be sure to reinstall them when you reinstall the scanner assembly.
4. At the rear of the product, remove four screws (callout 1), and then slide the scanner toward the
rear of the product to remove the assembly.
Figure 1-18 Remove the scanner assembly (2 of 2)
1
NOTE: The four scanner assembly screws removed in this step are a different size than the other
screws used on the product. Set these screws aside to use when you reinstall the scanner
assembly.
14 Chapter 1 Removal and replacement ENWW