Harman kardon AVR 505 LIMITED EDITION OWNER’S MANUAL

AVR 505 Limited Edition Audio/ VideoReceiver
OWNER’S MANUAL
DIGITAL LOGIC 7
VID 1
DVD
CD
TAPE
6 CH
VID 2
VID 3
PRO LOGIC
3 STEREO DSP
5 CH. STEREO
SURR. OFF
Surr. Select
Coaxial
RDS
Power for the Digital Revolution
®
2 TABLE OF CONTENTS
3 Introduction 4 Safety Information 4 Unpacking 5 Front Panel Controls 7 Rear Panel Connections
9 Remote Control Functions 12 Installation and Connections 12 Audio Equipment Connections 12 Video Equipment Connections 13 SCART A/V Connections 14 AC Power Connections 14 Speaker Selection and Placement 15 System Configuration 15 First Turn On 15 Settings to be Made
With Each Input Used
15 Input Setup 15 Speaker Setup 17 Triple Crossover Setting 17 Global/Independent
Bass Manager Memory
17 Surround Setup 18 Configuring the Surround Off
(Stereo) Modes
18 Speaker Setup 18 Stereo Digital Mode 18 Delay Settings 18 Night Mode Settings 19 Output Level Adjustment 20 Operation 20 Basic Operation 20 Source Selection 20 Controls and Use of Headphones 21 Surround Mode Chart 22 Surround Mode Selection 22 Digital Audio Playback 23 Selecting a Digital Source 23 Digital Status Indicators 23 Surround Mode Types 24 Night Mode 24 Tape Recording 24 Output Level Trim Adjustment 25 25 6-Channel Direct Input 25 Display Brigthness 25 Memory Backup 25 Tuner Operation 26 RDS Operation 27 Programming the Remote 27 Programming the Remote with Codes 28 Programmed Device Function 28 Macro Programming 29 Volume Punch-Through 29 Channel Control Punch-Through 29 Transport Control Punch-Through 29 Resetting the Remote Memory 30 Function List 32 Troubleshooting Guide 32 Processor Reset 33 Technical Specifications
Table of Contents
Typographical Conventions
In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used.
EXAMPLE – (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack
EXAMPLE – (OCR type) indicates a message that is visible on the front-panel information display
1
– (number in a square) indicates a specific front-panel control
– (number in a circle) indicates a rear-panel connection
0
– (number in an oval) indicates a button or indicator on the remote
Declaration of Conformity
We, Harman Consumer International
2, route de Tours 72500 Château-du-Loir, FRANCE
declare in own responsibility, that the product described in this owner’s manual is in compliance with technical stan­dards:
EN 55013/6.1990
EN 55020/12.1994
EN 60065:1993
EN 61000-3-2/4.1995
Carsten Olesen
Harman Kardon Europe A/S
09/03
INTRODUCTION 3
Introduction
Thank you for choosing Harman Kardon!
With the purchase of a Harman Kardon AVR 505 Limited Edition you are about to begin many years of listening enjoyment. The AVR 505 Limited Edition has been custom designed to provide all the excitement and detail of movie sound tracks and every nuance of musical selec­tions.With onboard Dolby* Digital and DTS
decoding, the AVR 505 delivers six discrete channels of audio that take advantage of the digital sound tracks from the latest DVD and LD releases and Digital Television broadcasts.
While complex digital systems are hard at work within the AVR 505 to make all of this happen, hookup and operation are simple. Color-keyed connections and a programmable remote con­trol make the AVR easy to use. To obtain the maximum enjoyment from your new receiver, we urge you to take the time to read through this manual. This will ensure that connections to speakers, source playback units and other exter­nal devices are made properly. In addition, a few minutes spent learning the functions of the various controls will enable you to take advan­tage of all the power the AVR 505 is able to deliver.
If you have any questions about this product, its installation or its operation, please contact your dealer. He is your best local source of information.
Description and Features
The AVR 505 Limited Edition is among the most versatile and multi-featured A/V receivers avail­able, incorporating a wide range of listening options. In addition to Dolby Digital and DTS decoding for digital sources, a broad choice of analog surround modes are available for use with sources such as CD,VCR,TV broadcasts and the AVR’s own FM/AM tuner. Along with the latest Dolby ProLogicII
®
decoding technology, Dolby 3 Stereo, 5 Ch Stereo and custom Hall and Theater modes, only Harman Kardon receivers offer Logic 7
®
to create a wider, more enveloping field environment and more defined fly-overs and pans.
Another Harman Kardon exclusive is VMAx, which uses proprietary processing to create an open, spacious sound field even when only two front speakers are available.
In addition to providing a wide range of listening options, the AVR 505 Limited Edition is easy to configure so that it provides the best results with your speakers and specific listening-room environment. A Stereo-Direct mode bypasses the digital processor to preserve all of the subtleties of older analog, two-channel materials, while bass management, available in the surround and Stereo-Digital modes,improves your ability to tailor the sound to suit your room acoustics or taste.
For the ultimate in flexibility, the AVR 505 features connections for four video devices, all with both composite and S-Video inputs, includ­ing the front-panel inputs.Two additional audio inputs are available, and a total of six digital inputs make the AVR 505 capable of handling all the latest digital audio sources. Coax and optical digital outputs are available for direct connec­tion to digital recorders. A video recording output and a six-channel input make the AVR 505 virtually future-proof, with everything needed to accommodate tomor­row’s new formats right on board.
The AVR 505 Limited Edition’s powerful amplifier uses traditional Harman Kardon high-current design technologies to meet the wide dynamic range of any program selection.
Harman Kardon invented the high-fidelity receiv­er fifty years ago.With state-of-the-art circuitry and time-honored circuit designs, the AVR 505 Limited Edition is one of the finest receivers ever offered by Harman Kardon within its price range.
Onboard Dolby Digital and DTS Decoding Using Crystal
®
Chip
Technology
Harman Kardon’s Exclusive Logic 7 and VMAx Modes
Dolby Laboratory's latest ProLogic II decoding technology.
Stereo-Direct Mode for Two-Channel Sources Bypasses DSP Processing to Preserve the Integrity of Analog Materials
Stereo-Digital Mode for Programmable Bass Management of Low Frequencies Between Main Speakers and Subwoofer
Front panel digital inputs for easy connection to portable digital devices and the latest video game consoles
Multiple Digital Inputs and Outputs
6-Channel Direct Input for Use With
DVD-Audio or SACD Players and Other Products With Internal Surround Decoders
Color-Coded Input,Output and Speaker Terminals Comply With CEA Standards for Easy Installation
Remote with Internal Codes Capability
4 SAFETY INFORMATION
Safety Information
Important Safety Information
Verify Line Voltage Before Use
Your AVR 505 Limited Edition has been designed for use with 220-240-Volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit.
If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your dealer before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service depot with a cord meeting factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug, never pull the cord. If you do not intend to use the unit for any con­siderable length of time, disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or a staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service station.
Installation Location
To assure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface.When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product.
Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances a fan may be required.
Do not place the unit directly on a carpeted surface.
Avoid installation in extremely hot or cold locations, or an area that is exposed to direct sunlight or heating equipment.
Avoid moist or humid locations.
Do not obstruct the ventilation slots on the
top of the unit, or place objects directly over them.
Cleaning
When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts.Avoid spraying insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet.
Unpacking
The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move, or should the unit ever need repair.
To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag.
If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environment and discard those materials at a local recycling center.
FRONT PANEL CONTROLS 5
1
Main Power Switch: Press this button to apply power to the AVR. When the switch is pressed in, the unit is placed in a Standby mode, as indicated by the orange LED
3
. This button MUST be pressed in to operate the unit. To turn the unit off completely and prevent the use of the remote control, this switch should be pressed until it pops out from the front panel so that the word “OFF” may be read at the top of the switch.
NOTE: This switch is normally left in the “ON” position.
2
System Power Control: When the Main
Power Switch
1
is “ON,” press this button to turn on the AVR; press it again to turn the unit off (to Standby). Note that the Power
Indicator
3
will turn blue when the unit is on.
3
Power Indicator: This LED will be illumi­nated in orange when the unit is in the Standby mode to signal that the unit is ready to be turned on. When the unit is in operation, the indicator will turn blue.
4
Headphone Jack: This jack may be used to listen to the AVR’s output through a pair of headphones. Be certain that the headphones have a standard 6.3 mm stereo phone plug. Note that the speakers will automatically be turned off when the headphones are connected.
5
Selector Buttons: When you are establish­ing the AVR’s configuration settings, use these buttons to select from the choices available, as shown in the Main Information Display
Ú
.
6
Tone Mode: Pressing this button enables or disables the Balance, Bass and Treble tone con­trols.When the button is pressed so that the words
TONE IN appear in the Main
Information Display
Ú
, the settings of the
Bass
^
and Treble*controls and of the
Balance control
&
will affect the output sig­nals.When the button is pressed so that the words
TONE OUT appear in the Main
Information Display
Ú
, the output signal will be “flat,” without any balance, bass or treble alteration.
Front Panel Controls
1 2 3 4 5 6 7 8 9 )
! @ # $ % ^ & * ( Ó
Ô  Ò Ú Û Ù ı ˆ ˜ ¯
Main Power Switch System Power Control Power Indicator Headphone Jack Selector Buttons Tone Mode Surround Mode Group Selector Tuning Tuner Band Selector Preset Stations Selector
Input Source Selector RDS Select Button Surround Mode Selector Surround Mode Indicators Remote Sensor Window Bass Control Balance Control Treble Control Volume Control Set Button
Input Indicators Delay Digital Input Selector Main Information Display Channel Select Button Speaker Select Button Digital Optical 3 Input Digital Coax 3 Input Video 3 input jacks Speaker/Channel Input Indicator
DIGITAL LOGIC 7
VID 1
DVD
CD
FMAM
TAPE
VID 2
VID 3
PRO LOGIC
3 STEREO DSP
5 CH. STEREO
SURR. OFF
1
2
4
Ù
78
Ò
)
%
$
Ú¯
&
˜
ˆ
ı
(
Ô
6
#
5
9
Ó
5
@
6 CH
Surr. Select
Coaxial 3
^
3
Û
!
RDS
*
6 FRONT PANEL CONTROLS
Front Panel Controls
7
Surround Mode Group Selector: Press this button to select the top-level group of sur­round modes. Each press of the button will select a major mode grouping in the following order:
Dolby Modes DTS Digital Modes DSP Modes Stereo Modes Logic 7 Modes
Once the button is pressed so that the name of the desired surround mode group appears in the
Lower Display Line
Ú
, press the Surround
Mode Selector
#
to cycle through the indi­vidual modes available. For example, press this button to select Dolby modes, and then press the Surround Mode Selector
#
to choose
from the various mode options.
8
Tuning Selector: Press the left side of the button to tune lower frequency stations and the right side of the button to tune higher frequency stations.When a station with a strong signal is reached,
MANUAL TUNED or AUTO
TUNED
will appear in the Main Information
Display
Ú
(see page 25 for more information
on tuning stations).
9
Tuner Band Selector: Pressing this button will automatically switch the AVR to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands, holding it pressed for some seconds will switch between stereo and mono receiving and between automatic and manual tuning mode (See page 25 for more information on the tuner).
)
Preset Stations Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 25 for more information on tuner programming.)
!
Input Source Selector: Press this button to change the input by scrolling through the list of input sources.
@ RDS Select Button: Press this button to dis- play the various messages that are part of the RDS data system of the AVR’s tuner. (See page 26 for more information on RDS).
#
Surround Mode Selector: Press this but­ton to select from among the available surround mode options for the mode group selected. The specific modes will vary based on the number of speakers available, the mode group and if the input source is digital or analog. For example, press the Surround Mode Group Selector
7
to select a mode grouping such as Dolby or Logic 7, and then press this button to see the mode choices available. For more information on mode selection, see page 22.
$
Surround Mode Indicators: A blue LED will light in front of the surround mode that is currently in use.
%
Remote Sensor Window:The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it.
^
Bass Control: Turn this control to modify the low frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.
&
Balance Control: Turn this control to change the relative volume for the front left/right channels.
NOTE: For proper operation of the surround modes this control should be at the midpoint or “12 o’clock” position.
*
Treble Control: Turn this control to modify the high frequency output of the left/right chan­nels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.
(
Volume Control:Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR is muted, adjusting volume control will automatically release the unit from the silenced condition.
Ó
Set Button: When making choices during the setup and configuration process, press this button to enter the desired setting as shown in the Main Information Display
Ú
into the AVR’s memory. The set button may also be used to change the display brightness. (See page 25.)
Ô
Input indicators: A blue LED will light in front of the input that is currently being used as the source for the AVR.
Delay: Press this button to begin the sequence of steps required to enter delay time settings. (See page 18 for more information on delay times.)
Ò
Digital Input Selector: When playing a source that has a digital output, press this button to select between the Optical
and
Coaxial
Digital inputs. (See pages
22-24 for more information on digital audio.)
Ú
Main Information Display: This display delivers messages and status indications to help you operate the receiver.
Û
Channel Select Button: Press this button to begin the process of trimming the channel output levels using an external audio source. (For more information on output level trim adjustment, see page 24.)
Ù
Speaker Select Button: Press this button to begin the process of selecting the speaker positions that are used in your listening room. (See page 15 for more information on setup and configuration.)
ı
Digital Optical 3 Input: Connect the opti­cal digital audio output of an audio or video prod­uct to this jack. When the Input is not in use, be certain to keep the plastic cap installed to avoid dust contamination that might degrade future performance.
ˆ
Digital Coax 3 Input: This jack is normally used for connection to the output of portable digital audio devices, video game consoles or other products that have a coax digital jack.
˜
Video 3 Input Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players.
¯
Speaker/Channel Input Indicators: These indicators are multipurpose, indicating either the speaker type selected for each channel or the incoming data-signal configuration.The left, cen­ter, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box. The center box lights when a “Small” speaker is selected, and the two outer boxes light when “Large” speakers are selected. When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been selected for that position. (See page 15 for more information on configuring speakers.) The letters inside each of the center boxes display active input channels. For standard analog inputs, only the L and R will light,indicat­ing a stereo input. When a digital source is play­ing, the indicators will light to display the chan­nels begin received at the digital input. When the letters flash, the digital input has been interrupt­ed. (See page 15 for more information on the Channel Indicators).
REAR PANEL CONNECTIONS 7
Rear Panel Connections
¢
·
°
¤
°
b
c
d
e
¡
d
b
·
ª
a
£
§
¤
           
           
Tape Inputs Tape Outputs Video 1 Audio Inputs AM Antenna Video 1 Audio Outputs DVD Audio Inputs FM Antenna CD Inputs Digital Audio Outputs Coaxial Digital Inputs Subwoofer Output Video Monitor Outputs
Front/Center Speaker Outputs Surround Speaker Outputs Switched AC Accessory Outlet Unswitched AC Accessory Outlet AC Power Cord DVD Video Inputs Video 1 Video Outputs Video 2 Audio Inputs Video 2 Video Inputs Optical Digital Inputs Video 1 Video Inputs 6-Channel Direct Inputs
Tape Inputs: Connect these jacks to the
PLAY/OUT jacks of an audio recorder.
Tape Outputs: Connect these jacks to the
RECORD/INPUT jacks of an audio recorder.
Video 1 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a VCR or other video source.
AM Antenna: Connect the AM loop antenna supplied with the receiver to these terminals. If an external AM antenna is used, make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna.
Video 1 Audio Outputs: Connect these jacks to the RECORD/INPUT audio jacks on a VCR or any other Audio recorder.
DVD Audio Inputs: Connect these jacks to the analog audio jacks on a DVD or other video source.
FM Antenna: Connect the supplied indoor or an optional external FM antenna to this terminal.
CD Inputs: Connect these jacks to the ana­log output of a compact disc player or CD changer.
Digital Audio Outputs: Connect these jacks to the matching digital input connector on a digital recorder such as a CD-R or MiniDisc recorder.
Coaxial Digital Inputs: Connect the coax digital output from a DVD player, HDTV receiver, LD player, MD player or CD player to these jacks. The signal may be either a Dolby Digital signal, DTS signal or a standard PCM digital source. Do not connect the RF digital output of an LD play­er to these jacks.
Subwoofer Output: Connect this jack to the line-level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input.
8 REAR PANEL CONNECTIONS
Rear Panel Connections
Video Monitor Outputs: Connect these jacks to the composite and/or S-Video input of a TV monitor or video projector to view the output of any video source selected by the receiver’s video switcher.
Front/Center Speaker Outputs: Connect these outputs to the matching + or – terminals on your front/center speakers.When making speaker connections, always make certain to maintain correct polarity by connecting the red (+) terminals on the AVR to the red (+) terminals on the speaker and the black (–) terminals on the AVR to the black (–) terminals on the speak­ers. (See page 14 for more information on speaker polarity.)
Surround Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right surround speakers.When making speaker connections always make cer­tain to maintain correct polarity by connecting the red (+) terminals on the AVR to the red (+) terminals on the speakers and the black (–) ter­minals on the AVR to the black (–) terminals on the speakers. See page 14 for more information on speaker polarity.
Switched AC Accessory Outlet: This out­let may be used to power any device that you wish to have turn on when the unit is turned on with the System Power Control switch
2
.
Unswitched AC Accessory Outlet: This outlet may be used to power any AC device. The power will remain on at this outlet regardless of whether the AVR is on or off (in Standby), pro­vided that the Main Power switch
1
is on.
Note: The total power consumption of all devices connected to the accessory outlets should not exceed 100 watts from the
Unswitched Outlet
and 50 W from the
Switched Outlet
.
AC Power Cord: Connect the AC plug to an
unswitched AC wall output.
DVD Video Inputs: Connect these jacks to the composite or S-Video output jacks on a DVD player or other video source.
Video 1 Video Outputs: Connect these jacks to the RECORD/INPUT composite or S-Video jack on a VCR.
Video 2 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a VCR or other video source.
Video 2 Video Inputs: Connect these jacks to the PLAY/OUT composite or S-Video jacks on a second VCR or other video source.
Optical Digital Inputs: Connect the optical digital output from a DVD player, HDTV receiver, LD player, MD player or CD player to these jacks. The signal may be either a Dolby Digital signal, a DTS signal or a standard PCM digital source.
Video 1 Video Inputs: Connect these jacks to the PLAY/OUT composite or S-Video jacks on a VCR or other video source.
Note: Either the Video or S-Video output of any S-Video source must be connected to the AVR, not both in parallel, otherwise the video may be disturbed or its performance be adversely effected.
6-Channel Direct Inputs: These jacks are used for connection to source devices such as DVD-Audio or SACD players with discrete analog outputs.
REMOTE CONTROL FUNCTIONS 9
Remote Control Functions
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q              
Power On Button IR Transmitter Window Program Indicator Power Off Button Input Selectors AVR Selector AM/FM Tuner Select Test Button Sleep Button Surround Mode Selector Night Mode Channel Select Button
⁄/¤
Buttons
Button Set Button Digital Select Numeric Keys Tuner Mode Direct Button Tuning Up/Down Macro Buttons Transport Controls Skip Up/Down Buttons RDS Select Button Preset Up/Down Clear Button Memory Button Delay/Prev. Ch.
Button Speaker Select Spare Button Volume Up/Down TV/Video Selector Mute Dim Button Dolby Mode Select Button DTS Digital Mode Select Button Logic 7 Mode Select Button Stereo Mode Select Button DTS Neo:6 Mode Select Button 6-Channel Direct Input
NOTE: The function names shown here are each button’s feature when used with the AVR. Most buttons have additional functions when used with other devices. See page 30 and 31 for a list of these functions.
a
c
e
f
7
l
q
r
t
` z
x
y
p
8
  
g
j
k
m
n
o
s
u
w
v
b
d
10 REMOTE CONTROL FUNCTIONS
Remote Control Functions
IMPORTANT NOTE: The AVR’s remote may be
programmed to control up to seven devices, including the AVR. Before using the remote, it is important to remember to press the Input Selector button
4
that corresponds to the unit you wish to operate. In addition, the AVR’s remote is shipped from the factory to operate the AVR and most Harman Kardon CD or DVD play­ers and cassette decks.The remote is also capa­ble of operating a wide variety of other products using the control codes that are part of the remote. Before using the remote with other prod­ucts, follow the instructions on pages 27 to pro­gram the proper codes for the products in your system.
It is also important to remember that many of the buttons on the remote take on different func­tions, depending on the product selected using the Input Selectors.The descriptions shown here primarily detail the functions of the remote when it is used to operate the AVR. (See page 30 and 31 for information about alternate functions for the remote’s buttons.)
0
Power On Button: Press this button to turn on the power to a device selected by pressing one of the Input Selectors
4
(except Tape).
1
IR Transmitter Window: Point this window towards the AVR when pressing buttons on the remote to make certain that infrared commands are properly received.
2
Program Indicator: This three-color indi­cator is used to guide you through the process of programming the remote. See page 27 for infor­mation on programming the remote.
3
Power Off Button: Press this button to place the AVR or a selected device unit in the Standby mode.
4
Input Selectors: Pressing one of these buttons will perform three actions at the same time. First, if the AVR is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR. Finally, it will change the remote control so that it controls the device selected. After pressing one of these buttons you must press the AVR Selector button
5
again to operate the
AVR’s functions with the remote.
5
AVR Selector: Pressing this button will switch the remote so that it will operate the AVR’s functions. If the AVR is in the Standby mode, it will also turn the AVR on.
6
AM/FM Tuner Select: Press this button to select the AVR’s tuner as the listening choice. Pressing this button when the tuner is in use will select between the AM and FM bands.
7
Test Tone: Press this button to begin the sequence used to calibrate the AVR’s output lev­els. (See page 19 for more information on calibrating the AVR.)
8
Sleep Button: Press this button to place the unit in the Sleep mode.After the time shown in the display, the AVR will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order:
Hold the button pressed for two seconds to turn off the Sleep mode setting. Note that this button is also used to change channels on your TV, VCR and SAT receiver when selected.
9
Surround Mode Selector: Press this button to begin the process of changing the surround mode. After the button has been pressed, use the
⁄/¤
buttons Cto select the desired surround mode (See page 22 for more information). Note that this button is also used to tune channels when the TV, VCR and SAT receiver is selected using the Input
Selector
4
.
A
Night Mode: Press this button to activate the Night mode.This mode is available only with Dolby Digital encoded digital sources, and it pre­serves dialog (center channel) intelligibilty at low volume levels (See page 24 for more informa­tion).
B
Channel Select Button: This button is used to start the process of setting the AVR ’s out­put levels with an external source. Once this button is pressed, use the
⁄/¤
buttonsCto select the
channel being adjusted, then press the Set button
E
, followed by the
⁄/¤
buttons again, to change the level setting. (See page 25 for more information.)
C
⁄/¤
Buttons: These are multi-purpose buttons. They will be used most frequently to select a surround mode.These buttons are also used to increase or decrease output levels when config­uring the unit, to select speaker configuration or to select the digital inputs.They are also used to enter delay time settings after the Delay button
has been pressed.
When the AVR remote is being programmed for the codes of another device, these buttons are also used in the “Auto Search” process (See page 27 for more information on programming the remote.)
D‹Button: This button does not have a function with the AVR. When a DVD player or TV is selected, it may be used to navigate the menus of those devices.
E
Set Button: This button is used to enter settings into the AVR ’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjust­ment.
F
Digital Select: Press this button to assign one of the digital inputs
ıˆ
to a source. (See page 23 for more information on using digital inputs.)
G
Numeric Keys: These buttons serve as a ten-button numeric keypad to enter tuner preset positions.They are also used to select channel numbers when TV, VCR or Sat receiver has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.
H
Tuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so
MANUAL appears in the Main
Information Display
Ú
, pressing the Tuning
buttons
J8will move the frequency up or
down in single-step increments.When the FM band is in use and
AUTO appears in the Main
Information Display
Ú
, pressing this button will change to monaural reception making even week stations audible. (See page 25 for more information.)
I
Direct Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys
G
to select a station (See page 25 for more information on the tuner).
J
Tuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode but- ton
H
has been pressed or the Band button
9
on the front panel was held pressed so that
AUTO appears in the Main Information
Display
Ú
, pressing either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the
MANUAL appears in the Main
Information Display
Ú
, pressing these but­tons will tune stations in single-step increments. (See page 25 for more information.)
90
min80min70min60min50min
40
min
30
min20min10min
OFF
REMOTE CONTROL FUNCTIONS 11
Remote Control Functions
K
Macro Buttons: Press these buttons to store or recall a “Macro”, which is a pre-programmed sequence of commands stored in the remote. (See page 28 for more information on storing and recalling macros.)
L
Transport Buttons: These buttons do not have any functions for the AVR, but they may be programmed for the forward/reverse play opera­tion of a wide variety of CD or DVD players, and audio or video- cassette recorders. (See page 27 for more information on programming the remote.)
M
Skip Up/Down Buttons: These buttons do not have a direct function with the AVR, but when used with a compatibly programmed CD or DVD changer they will change the tracks on the disc currently being played in the changer.
N
RDS Select Button: Press this button to display the various messages that are part of the RDS data system of the AVR ’s tuner. (See page 26 for more information on RDS).
O
Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR ’s memory. When CD or DVD is selected using the Input Selector button
4
, these buttons may func-
tion as Slow Fwd/Rev (DVD) or ”+10” (CD).
P
Clear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.
Q
Memory Button: Press this button to enter a radio station into the AVR ’s preset memory.Two underline indicators will flash at the right side of the Main Information Display
Ú
, you then have five seconds to enter a preset memory location using the Numeric Keys
G
. (See
page 25 for more information.)
Delay/Prev Ch.: Press this button to begin the process for setting the delay times used by the AVR when processing surround sound. After pressing this button, the delay times are entered by pressing the Set button
E
and then using
the
⁄/¤
buttons Cto change the setting. Press the Set button again to complete the process. (See page 18 for more information.)
›Button: This button does not have a function with the AVR. When a DVD player or TV is selected, it may be used to navigate the menus of those devices.
Speaker Select: Press this button to begin the process of configuring the AVR’s Bass Management System for use with the type of speakers used in your system. Once the button has been pressed, use the
⁄/¤
buttons Cto select the channel you wish to set up. Press the Set button
E
and then select the speaker
type (see page 15 for more information.)
Spare Button: This button does not have any function for the operation of the AVR, but it is available for use when programmed with the code from another remote. (See page 27).
Volume Up/Down: Press these buttons to
raise or lower the system volume.
TV/Video Button: This button does not have a direct function on the AVR, but when used with a compatibly programmed VCR, DVD or satellite receiver that has a “TV/Video” func­tion, pressing this button will switch between the output of the player or receiver and the external video input to that player. Consult the Owner’s Manual for your specific player or receiver for the details of how it implements this function.
Mute: Press this button to momentarily silence the AVR or TV set being controlled, depending on which device has been selected.
When the AVR remote is being programmed to operate another device, this button is pressed with the Input Selector button
4
to begin the programming process. (See page 27 for more information on programming the remote.)
NOTE: As any of the remote buttons pressed is active with the device selected, the correspon­ding Selector button
45
will briefly flash
red to confirm your selection.
Dim Button: Press this button to activate the Dimmer function, which reduces the bright­ness of the front panel display, or turn it off entirely.The first press of the button shows the default state, which is full brightness by indicat­ing
DIMMER FULL in the Main
Information Display
Ú
. Press the button again within five seconds to reduce the bright­ness by 50%, as indicated by
DIMMER
HALF
. Press the button again within five sec­onds and the main display will go completely dark. Note that this setting is temporary; the dis­play will always return to full brightness when the AVR is turned on. In addition,both the
Power Indicator
3
and the blue accent light­ing inside the volume control will always remain at full brightness regardless of the setting. This is to remind you that the AVR is still turned on.
Dolby Mode Selector: This button is used to select one of the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes, Dolby 3 Stereo or Dolby Digital. Note that the Dolby Digital mode is only available with a digital input selected and the other modes only as long as a Dolby Digital source is not playing . See page 21 for the available Dolby surround mode options.
DTS Digital Mode Selector: When a DTS source is in use the AVR will select the appropri­ate mode automatically and no other mode will be available. Pressing this button will display the mode currently selected by the AVR´s decoder, depending on the surround material played and the speaker setting.
Logic 7 Selector: Press this button to select one of the available Logic 7 surround modes. (See page 21 for the available Logic 7 options).
Stereo Mode Selector: Press this button to select a stereo playback mode.When the button is pressed so that
DSP SURR OFF appears
in the Main Information Display
Ú
, the AVR will operate in a bypass mode with true fully analog, two-channel left/right stereo mode with no surround processing or bass management as opposed to other modes where digital process­ing is used. When the button is pressed so that
SURROUND OFF appears in the Main
Information Display
Ú
, you may enjoy a two-channel presentation of the sound along with the benefits of bass management. When the button is pressed so that
5 C H STEREO
appears, the stereo signal is routed to all five speakers, if installed.(See page 18 for more information on stereo playback modes).
DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the various DTS Neo:6 modes, which extract a five­channel surround field from two-channel pro­gram material (from PCM source or analog input signal). The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects the next mode in the following order:
6-Channel Direct Input: Press this button to select the component connected to the
6-Channel Direct Input
N
as the audio. Note that when you wish to use the Six Channel Direct Input in conjunction with a video source, you must first select the video source by pressing one of the Input Selectors
4
. Then press this
button to choose the 6-Channel Direct Input
N
as the audio source.
DTS Neo:6 MUSIC
DTS Neo:6 CINEMA
Loading...
+ 23 hidden pages