Harman kardon AVR 325 Quick-Start Guide

Thank you for purchasing a Harman Kardon AVR 325.This Quick-Start Guide will help you with a basic system installation. For detailed information on any step,please refer to the Owner’s Manual pages referenced in this guide.We strongly recommend that you read the Owner’s Manual for complete details on how to install, configure and operate the AVR 325, as well as for the important safety information it contains.
Figure 1 – Speaker Placement
The colors shown for each speaker correspond to the matching output terminal connection on the back of the AVR 325 (see page 8).
FRONT
LEFT
SPEAKER
(White)
SURROUND
BACK
LEFT
SPEAKER
(Brown)
SURROUND
BACK
RIGHT
SPEAKER
(Tan)
CENTER
SPEAKER
(Green)
SUBWOOFER
(Purple)
SURROUND
LEFT
SPEAKER
(Blue)
FRONT
RIGHT
SPEAKER
(Red)
SURROUND
RIGHT
SPEAKER
(Gray)
Step 1. Place your speakers in the listening room
(see page 18).
SPEAKER PLACEMENT
AVR 325 QUICK-START GUIDE
Connections Color Guide
Audio Connections Left Right
Front Center Surround Subwoofer Surround Back
Digital Audio Connections
Coax Optical
Video Connections
Composite S-Video
Match the colored jacks on the AVR 325 to the appropriate jacks on your source equipment or speakers.The colors are standardized,but not all equipment or connectors use them.
AVR 325 QUICK-START GUIDE
Step 2. Connect the speakers to the receiver:red (+)on speaker to colored (+) on receiver and black (–) to black (–)
(see page 15).
Step 3. Connect the Subwoofer Pre-Out jack to the Line-In jack on your subwoofer.
Adjust the settings on the subwoofer as needed (see page 15).
Figure 3 – How To Use the Binding-Post
Speaker Terminal
Figure 2 – Speaker Connections
_
+
SURROUND
LEFT SPEAKER
FRONT LEFT
SPEAKER
_
+
CENTER SPEAKER
_
+
FRONT RIGHT
SPEAKER
_
+
_
+
SURROUND
RIGHT SPEAKER
LINE IN/SUB/LFE
SUBWOOFER
_
+
SURROUND BACK
LEFT SPEAKER
_
+
SURROUND BACK
RIGHT SPEAKER
SPEAKER AND AUDIO CONNECTIONS
AUDIO RECORDER
Step 4. Connect AM and FM antennas (Fig.4) (see page 15). Step 5. Connect source components, as shown in Figures 4 and 5,and the
Device Connection Options chart on the back of this guide (see
pages 15–16). AUDIO connections: Right channel (red) on source to right (red) on AVR,and left channel (white) on source to left (white) on AVR. DIGITAL AUDIOconnections,if available: Choose either coax (orange) to coax (orange) OR optical to optical for each device. The Coax 1 input defaults to the DVD player, but may be reassigned. Assign the other digital inputs and outputs as appropriate for your equipment (see Step 7).
VIDEO connections: Choose component (Y/Pb/Pr – green/blue/ red), composite (yellow) or S-Video (4-pin) for each video source.
Connect the component, composite and S-Video Monitor outputs to
your Video Monitor (TV).Switch your TV set’s input to match the type of video used for the currently selected source.
Step 6. Plug all components into AC power outlets.The outlets on the back
of the AVR325 should be used
only for low-current products,such
as CD or DVD players,and the total should not exceed 100 watts.
Basic Receiver Configuration
Step 7. Select digital inputs:If your DVD is connected to Coax 1, no adjust-
ment is needed. For any other digital-device connections,use the front-panel Digital Select button and the arrow buttons to select an optical or coax digital input (see pages 20 and 27).
Step 8.
Select a surround mode: Press the Surround Mode button on the front panel to select Dolby®Pro Logic®II – Movie.(You may select other modes later as you become familiar with the AVR 325;see pages 20–21 and 26–29.)
Step 9.
Configure speakers: No action is needed if you have five “small” satellite-type speakers and a subwoofer. Otherwise, press the Speaker button and then the Set and arrow buttons to select the correct speaker choices for your system (see pages 21–23).
Step 10.
Use EzSet™to set output levels: Set the Balance to 12 o’clock, and the Volume to –10dB.Sit in the listening position and hold the remote in front of you at shoulder level, pointing at the AVR 325. Press the SPL button for 3 seconds,and release it when the LED flashes amber. Press “5” or “7”to indicate the number of speakers. Hold the remote steady until the process is completed (see pages 24–25).
Step 11.
Your system is configured – sit back and enjoy!
Figure 4 – Audio Connections
Dashed lines (––––) indicate coax and optical digital audio connections. Choose either type (but not both) for each digital audio source.
REC/IN
PLAY/OUT
CD PLAYERAM AntennaFM Antenna
L R Optical Coax
DVD PLAYER
VCR (Video 1) TV or Video Monitor (Video 2)
In/Rec
Out/Play
OUT
IN
L R VIDEO
L R Video S-Video Component Video
Y Pb Pr
Component Video
Y Pb Pr
Component Video
Y
Pb
Pr
Optical Coax
Cable or Sat or HDTV Set-Top Box (Video 3)
OUT
L R Video S-Video
Optical Coax
L R Video S-Video
VIDEO CONNECTIONS
Device Connection Options: Recommended connections are shown in red,but connections may be made to best fit your system requirements.The Video 4, Coax 3 and Optical 3 inputs are on the front panel of the receiver. Device Input Name Audio Input Connections Audio Output Connections Video Connections
CD Player CD CD L/R Inputs,Optical Digital 1 or 2, or Coaxial Digital 1 or 2 Not required Not required DVD Player DVD Coaxial Digital 1 or 2, Optical Digital 1 or 2,or DVDL/R Inputs Not required DVD Component, Composite or S-Video VCR Video 1 Video 1 L/R Inputs Video 1 L/R Outputs Video 1 Composite or S-Video Input and Output Cable Box or Satellite Receiver Video 3 Video 3 L/R Inputs,Optical Digital 3*,or Coaxial Digital 3*Inputs Not required Video 3 Composite or S-Video Input Audio Recorder Tape Tape L/R Inputs,Optical Digital 1/2** or Coaxial Digital 1/2** Inputs Tape L/R Outputs,Digital Optical** or Coaxial Outputs** Not required TV or Projector Video 2 or 3 Video 2 or 3 L/R Inputs Not required Monitor-Out Component, Composite and/or S-Video
*
Check with your cable company to determine whether digital audio is available for all channels.It may be necessar y to make BOTH analog and digital connections if it is not.**Digital audio recorders only.
250 Crossways Park Drive,Woodbury, New York 11797 www.harmankardon.com © 2003 Harman International Industries,Incorporated Part No. 55740120
Power for the Digital Revolution.
®
®
Figure 5 – Video Connections
Dashed lines (––––) indicate coax and optical digital audio connections. Choose either type (but not both) for each digital audio source. Dotted lines (
••••) indicate component, composite or S-Video connections.Component video is the preferred connection when available, but you may use any of the three types (but not more than one).When component, composite and S-Video sources are connected to the AVR you must also connect all outputs from the AVR to your TV.
Loading...