Haier HSU-18LA10, HSU-12LA10, HSU-09LA10 Manual

0 (0)

REMOTE CONTROLLER

DISPLAY button

Press it once to stop the indoor unit displaying and press again to make it display.

SLEEP button

Please see“sleep mode”.

OPERATION

MODE button

Press it to select operation mode:

AUTO COOL HEAT FAN DRY

TEMPERATURE

ADJUSTMENT buttons

Press it once, the setting tempera- -ture decreases by 1.The range of setting temperature is 16-31.

FAN SPEED button

Press it to change the fan speed

in the order of low-medium-high

-auto ( AUTO).

UP&DOWN SWING button

Please see“adjustment of air flow direction”.

Signal ejecting window

It sends signals to the indoor unit.

123 hours OnOff

AUTO

¡æ

SWING FAN AUTO SWING

SLEEP DISPLAY TIMER/CL. TURBO

MODE

I/O

FAN SPEED

INOIZER

OPERATION DISPLAY

It displays the current settings.

TIMER SET/CLOCK button

Press it to fix the timer setting or to set the clock to the present time.

TURBO button

Press it to start turbo function

and press again to stop it.

RUN/STOP button

Turns unit ON/OFF.

TEMPERATURE

ADJUSTMENT buttons

Press it once, the setting tem- -perature increases by 1.

LEFT&RIGHT SWING button

Please see“adjustment of air flow direction”.

INOIZER button

Press it to start inoizer function

and press again to stop it.

NOTICE:

Cool only type has no HEAT mode.

To operate, the distance should be within 6 meters from the indoor unit with a clear line of sight.

Remove the batteries if the remote controller is not to be used for long periods of time.

As this is a all-purpose remote controller which contains many functional buttons, please refer to the function of the air conditioner to know about the actual function.

Don't tear the batteries apart or throw them into fire, which will lead to irreparable damage.

When transferring from one mode to another, it may needs less than 3 minutes’ delay to protect compressor.

OPERATION MODE ADJUSTMENT

1. AUTO mode AUTO

In this mode, the air conditioner can automatically adjust the room temperature to decide the most suitable temperature. At the start of operation, the air conditioner will automatically select the operation mode according to the room temperature. The following table shows the conditions which are set at start up.

Room				Cool only type		Heat pump type
Temperature (RT)			Mode	Initial Setting Temperature	Mode	Initial Setting Temperature
RT	26		Cool	24	Cool	24
26	RT	25		RT-2		RT-2

25	RT	23	Dry	RT-2	Dry	RT-2
Rt	23			21	Heat	26

2. COOL mode

Press UP & DOWN SWING button to change up/down air flow direction and LEFT & RIGHT SWING button to change left/right air flow direction. Press FAN SPEED button to change the fan speed of indoor unit.

Press TEMPERATURE ADJUSTMENT button to change the set temperature.

3. DRY mode

In this mode, the air conditioner automatically sets the room temperature and this temperature will not appear on display.

TEMPERATURE ADJUSTMENT button and FAN SPEED button are not functional.

Press UP & DOWN SWING button or LEFT & RIGHT SWING button to change air flow direction.

4. FAN mode

In this mode, the outdoor unit does not operate. The indoor fan alone operates.

Press UP & DOWN SWING button or LEFT & RIGHT SWING button to change air flow direction.

Press FAN SPEED button to change the fan speed of indoor unit.

TIMER&SET OPERATION

Timer operation

ON/OFF timer operation set

Press button Timer/CL when the air conditioner is on or off	to initiate the
¡±	¡±
OFF or ON TIMER function.
¡±

Every press of button Timer/CL increases the ON/OFF time by one hour(24 hours at most).

ON/OFF timer operation cancellation

If you want timer operation cancelled, press button Timer/CL until the icon

of timer“ ”,the time and “hours on” or “hours off” disappear on the remote controller display.

Note: When the air conditioner is on timer operation,if you want to reset the timer you must cancel the former timer, or the setting will not in accord with actual condition.

Clock set

As long as the remote controller is on power, the clock will run all the time

and it can be adjusted in any condition even when the air conditioner is off.

¡±

While the air conditioner is electrified for the first time, the time of the clock

¡± is “ 0:00 ”, the flash¡±of “: ” means the clock counts the time automatically.

Press the button “Timer/CL” for 3 seconds, the time of the clock can be adjusted. At that time the time of hour flashes, during this period you can add the time of hours by pressing the button “” and reduce the time by pressing the button“ ”. After setting the time of hour, press the button Timer/CL again to adjust the time of minute(do not need to press it for 3 seconds).When the time of minute flashes, press the button“” to add the time of minute, and press the button “ ” to reduce it. Finish setting the time of minute, press the button “Timer/CL” for the third time to confirm the time of the clock.

Note: The time of the clock will only display when the air conditioner isn't set timer, otherwise it will not display.

5. HEAT mode¡± (only applied¡± to heat pump type)

Press MANUAL SWING button or SWING button to change up/down air flow direction.

Press FAN SPEED button to change the fan speed of indoor unit.

Press TEMPERATURE ADJUSTMENT button to change the set temperature.

6. TURBO function (only applied to turbo series)

This function will make the air conditioner heat or cool quickly and during this period, the noise of the air conditioner will increase. Turbo function can be only started up in heat or cool mode(turbo heating or turbo cooling) otherwise, it can not be started up. When the air conditioner is in cool or heat mode, press turbo button to initiate turbo function, the remote con- -troller displays “TURBO” and the icon of fan speed is “ ”,meanwhile the air conditioner cannot be controlled by the remote controller. Press turbo button again or start up sleep mode or transit modes to exit turbo function. After exiting turbo function the fan runs at low speed.