Frigidaire FFFH20F3VW, FFFU20F2VW Wiring Diagram

IMPORTANT SAFETY NOTE

The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance.

IMPORTANT

If any green/yellow grounding wires are removed during servicing, theymustbereturnedtotheiroriginalpositionandproperlysecured.

PERFORMANCE

	Ambient Temperature	70ºF	90ºF
	Operating Time	100%	100%
	Freezer Temperature	4 to -4ºF	4 to -4ºF
	Low Side Pressure (cut-in)	-	-
	Low Side Pressure (cut-off)	-7.02 to -3.94	-6.63 to -4.65
		PSIG	PSIG
	High Side Pressure	35 to 37 PSIG	51 to 56 PSIG
	Wattage	32W	46.6W
	Amps	0.4	0.61
	Base Voltage	115V	115V
	Refrigerant Charge	50g	50g

SERVICE DATA SHEET

A14365701

AUTOMATIC DEFROST UPRIGHT

FREEZER - R600a

DEFROST CONTROL

The defrost period will vary dependent on the heater on time, with a maximum of 60 minutes. There is a 7 minute idle (drip time) time after the heater turns off before the evaporator fan and compressor will turn on. During the defrosting period a temperature sensor monitors the evaporator temperature and the main control board turns the defrost heater off after the frost on the evaporator has melted.

IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION.

Specifications subject to change without notice. For complete performance data by model, refer to service manual. Options shown are not necessarily part of the model.

SERVICE MODE DIAGNOSTIC TESTS

Allows technicians to step through available tests to diagnose individual electrical circuits.

NOTE: There is a magnetic switch located in the bottom front of the cabinet (beside the green power on indicator light) and a permanent magnet is located in a holder in the bottom of the door that work together to sense when the door is opened and closed.

To Enter	• Open the door.
Service Mode:	• Using a permanent magnet, activate the magnetic
	switch 4 times within 2 seconds, holding the forth
	activation against the magnetic switch until a long beep
	is heard and the interior AC LED Light bulb turns on.
	• Move the magnet away from the magnetic switch.
	The internal light will turn off indicating the unit is in
	service mode.
	NOTE: When service mode is entered, the green
	power on indicator light will remain on.
	• Using the permanent magnet, activate the magnetic
	switch 2 times to terminate the current test and
	activate the next test. Two beeps will sound confirming
	the service mode has advanced to the next test.
	• Test 1: Compressor and condenser fan:
	The compressor and condenser fan turns ON as
	soon as service mode is activated.
	• Test 2: Defrost heater
	NOTE: The defrost heater has a thermal fuse on
	each side of the heater element. During the defrost
	heater test the main board monitors the evapora-
	tor temperature and will automatically turn off
	the defrost heater, if the evaporator temperature
	exceeds a specified value to ensure the thermal
	fuses are not permanently open circuited as they
	are designed to operate.
	• Test 3: AC LED bulb
	CAUTION: DO NOT REPLACE THE AC LED BULB
	WITH ANY BULB GREATER THAN 5 WATTS.
	• Test 4: Evaporator Fan
To manually exit	• Using a permanent magnet, activate the magnetic
service mode:	switch 4 times in 2 seconds, holding the forth activa-
	tion against the magnetic switch until a long beep is
	heard and the interior AC LED Light bulb turns on. The
	unit will restart in normal operating mode.
	• Unplug the unit from power and plug it back in to
	power. The unit will restart in normal operating mode.
	• The unit will automatically exit service mode if no
	magnetic switch activation is detected after 10 min-
	utes. The unit will restart in normal operating mode.
To activate	• Using a permanent magnet, activate the magnetic switch
manual defrost:	5 times in 2 seconds, holding the fifth activation against
	the magnetic switch until five short beeps are heard.
	• The unit can enter in manual defrost only during
	normal operating mode.
	• The unit will not enter in manual defrost if already
	in defrost mode.
	• The unit will not enter manual defrost if the tem-
	perature control knob is in the OFF position.
	• The defrost heater has a thermal fuse on each side of
	the heater element. During manual defrost, the main
	board monitors the evaporator temperature and will
	automatically turn off the defrost heater if the evapo-
	rator temperature exceeds a specified value to ensure
	the thermal fuses are not permanently open circuited
	as they are designed to operate.