EINHELL BT-MG 180 Kit Original Operating Instructions

t

Original operating instructions
Multifunction Tool



Art.-Nr.: 44.650.03 I.-Nr.: 01019

BT-MG

180 Kit

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:51 Uhr Seite 1

2

2

9

3

a

8

1

1

8

3

2

9

4

7

6

5

b

6

b

7

9

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:51 Uhr Seite 2

3

4 5

6

1

5

4 2

c

c

3

a

1.

b

4

2.

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 3

GB

4

Table of contents

1. Safety regulations

2. Layout

3. Supplied package

4. Intended use

5. Technical data

6. Before starting the equipment

7. Starting up

8. Replacing the power cable

9. Cleaning, maintenance and ordering of spare parts

10. Disposal and recycling

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 4

GB

5

“Caution - Read the operating instructions to reduce the risk of inquiry”

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Ꮯ

Wear a breathing mask.

Dust which is injurious to health can be generated when working on wood and other materials.
Never use the device to work on any materials containing asbestos!



Wear safety goggles.

Sparks generated during working or splinters, chips and dust emitted by the device can cause
loss of sight.



Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 5

6

GB

 Important!

When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with due
care. Keep this manual in a safe place, so that the
information is available at all times. If you give the
equipment to any other person, give them these
operating instructions as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.

1. Safety regulations

The corresponding safety information can be found
in the enclosed booklet.

 CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.

Keep all safety regulations and instructions in a
safe place for future use.

2. Layout (Fig. 1)

1. ON/OFF switch

2. Tool mounting

3. Dust extractor adapter

4. Dust extraction device

5. Allen key

6. Saw blade

7. Scraper

8. Triangular sanding/grinding plate

9. Allen key for changing tools

3. Supplied package

 Multifunction Tool
 Dust extractor adapter
 Dust extractor device
 Allen key
 Saw blade
 Scraper
 Triangular sanding/grinding plate
 Allen key for changing tools
 12x sanding paper (6x wood / 6x metal)

4. Proper use

The equipment is designed for the sanding/grinding
of wood, iron, plastic and similar materials using the
appropriate sanding/grinding paper. Furthermore, the
equipment is intended for sawing wood, plastic and
similar materials, as well as scraping off glued
carpets, filling compound residues, old paint and
similar applications.

The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.

Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

5. Technical data

Mains voltage: 230 V ~ 50 Hz
Power input: 180 W
Idling speed: 21000 rpm
Oscillation angle: 3°
Protection class: II / 쓑
Weight: 1.3 kg

Sound and vibration

Sound and vibration values were measured in
accordance with EN 60745.

LpAsound pressure level 89.6 dB(A)

KpAuncertainty 3 dB

LWAsound power level 100.6 dB(A)

KWAuncertainty 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 6

7

GB

Handle

Vibration emission value ah= 3.516 m/s²
K uncertainty = 1.5 m/s

2

 Important!

The vibration value changes according to the area of
application of the electric tool and may exceed the
specified value in exceptional circumstances.

Keep the noise emissions and vibrations to a
minimum.

 Only use appliances which are in perfect working

order.

 Service and clean the appliance regularly.
 Adapt your working style to suit the appliance.
 Do not overload the appliance.
 Have the appliance serviced whenever

necessary.

 Switch the appliance off when it is not in use.
 Wear protective gloves.

6. Before starting the equipment

 Before you connect the equipment to the mains

supply make sure that the data on the rating plate
are identical to the mains data.

 Always pull the power plug before making

adjustments to the equipment.

6.1 Fitting the plug-in tools (Figures 1/2/3)

 To fit the plug-in tools safely you should hold the

multifunction tool so that the ON/OFF switch (1)
points down and the tool mounting (2) faces up.

 Place the plug-in tool (e.g. the triangular

sanding/grinding plant) on the tool mounting (2)
so that the pins of the tool mounting (2) fit into the
recesses in the plug-in tool.

 Secure the plug-in tool using the supplied screw

(b) and tighten the screw securely with the Allen
key (9).

 Make sure that the washer (a) is used for the

screw (b) only in connection with the saw blade
and the scraper (see Figure 3). In this case the
corrugated face of the washer must be placed
against the plug-in tool.

Check that the plug-in tool is secure.

6.2 Triangular sanding/grinding plate

Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.

6.2.1 Fastening the sanding/grinding paper

The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the vacuum
extraction holes on the sanding/grinding paper and
the sanding/grinding disk are aligned.

6.3 Fitting the dust extraction device (Fig. 4/5)

The dust extraction system prevents the
accumulation of dirt and high dust loads in the air,
and it makes it easier to dispose of the dust.

 Place the equipment in a stable position as

shown in 6.1.

 Fit the dust extraction device (4) with the tool

mounting (2) positioned as shown in Figure 4.

 Use the Allen key (5) to secure the screws (c) in

the holes provided.

 Connect the extractor adapter (3) to the dust

extraction device (4). Make sure that the arrow
(a) on the extractor device coincides with the
recess (b) on the dust extraction device (4) (see
Fig. 5). Turn the extractor adapter (3) anti­clockwise until it engages..

 Connect your tool to an extraction unit or vacuum

cleaner. This will provide excellent extraction of
chips and dust from the workpiece.

The benefits are that you will protect both the
equipment and your own health. Your work area will
also be clean and safe.

7. Starting up (Fig. 6)

7.1 Switching on/off

Slide the switch (1) forwards to switch on the
equipment.

7.2 Practical tips

 Switch on the equipment.
 Work away from the body.
 Never move your hands into the direct vicinity of

the work area.

 Use only plug-in tools which are in good working

order and undamaged.

7.2.1 Plug-in tools
Sawing: Sawing wood and plastic.

Notes on working practice: When sawing, watch out
for foreign bodies in the workpiece and remove these
if necessary. Plunge cutting is allowed only in soft
materials such as wood or plasterboard.

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 7

8

GB

Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depending
on choice of sanding/grinding paper for the
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment offers
particularly high performance for the sanding/grinding
of hard-to-reach corners and edges. To sand/grind
profiles and channels you can also work with just the
tip or the edge of the sanding/grinding disk. Various
sanding/grinding papers are available, specially
designed for the different types of material you may
be working on and the amount you wish to remove
from the surface. The amount removed will depend
largely on the choice of sanding/grinding paper and
pressure applied to the sanding/grinding disk.

Scraping: Scraping off old paint or adhesives.
Notes on working practice: Move the plug-in tool
against the area you want to remove. Begin with a flat
angle of incidence and little pressure. The surface
(e.g. wood, plaster) may be damaged if too much
pressure is used.

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after­sales service or similarly trained personnel to avoid
danger.

9. Cleaning, maintenance and
ordering of spare parts

Always pull out the mains power plug before starting
any cleaning work.

9.1 Cleaning

 Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.

 We recommend that you clean the device

immediately each time you have finished using it.

 Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.

9.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.

9.3 Maintenance

There are no parts inside the equipment which
require additional maintenance.

9.4 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:

 Type of machine
 Article number of the machine
 Identification number of the machine
 Replacement part number of the part required

For our latest prices and information please go to
www.isc-gmbh.info

10. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 8

9

k erklärt folgende Konformität gemäß EU-Richtlinie und

Normen für Artikel

t explains the following conformity according to EU

directives and norms for the following product

p déclare la conformité suivante selon la directive CE et les

normes concernant l’article

C dichiara la seguente conformità secondo la direttiva UE e

le norme per l’articolo

N verklaart de volgende overeenstemming conform EU

richtlijn en normen voor het product

m declara la siguiente conformidad a tenor de la directiva y

normas de la UE para el artículo

O declara a seguinte conformidade, de acordo com a

directiva CE e normas para o artigo

l attesterer følgende overensstemmelse i medfør af

EU-direktiv samt standarder for artikel

U förklarar följande överensstämmelse enl. EU-direktiv och

standarder för artikeln

q vakuuttaa, että tuote täyttää EU-direktiivin ja standardien

vaatimukset

. tõendab toote vastavust EL direktiivile ja standarditele
j vydává následující prohlášení o shodě podle směrnice

EU a norem pro výrobek

X potrjuje sledečo skladnost s smernico EU in standardi za

izdelek

W vydáva nasledujúce prehlásenie o zhode podľa smernice

EÚ a noriem pre výrobok

A a cikkekhez az EU-irányvonal és Normák szerint a

következő konformitást jelenti ki

P deklaruje zgodność wymienionego poniżej artykułu z

następującymi normami na podstawie dyrektywy WE.

e декларира съответното съответствие съгласно

Директива на ЕС и норми за артикул

H paskaidro šādu atbilstību ES direktīvai un standartiem
G apibūdina šį atitikimą EU reikalavimams ir prekės

normoms

Q declară următoarea conformitate conform directivei UE

şi normelor pentru articolul

z δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την

Οδηγία ΕΚ και τα πρότυπα για το προϊόν

B potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

f potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

4 potvrđuje sledeću usklađenost prema smernicama EZ i

normama za artikal

T следующим удостоверяется, что следующие

продукты соответствуют директивам и нормам ЕС

1 проголошує про зазначену нижче відповідність

виробу директивам та стандартам ЄС на виріб

5 ја изјавува следната сообрзност согласно

ЕУ-директивата и нормите за артикли

Z Ürünü ile ilgili AB direktifleri ve normları gereğince

aşağıda açıklanan uygunluğu belirtir

L erklærer følgende samsvar i henhold til EU-direktivet

og standarder for artikkel

E Lýsir uppfyllingu EU-reglna og annarra staðla vöru

Konformitätserklärung

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Multifunction Tool BT-MG 180 Kit

Standard references: EN 14121; EN 60745-1; EN 60745-2-4; EN 55014-1; EN 55014-2;

EN 61000-3-2; EN 61000-3-3

x

x

2006/95/EC
2005/32/EC
2004/108/EC
2004/22/EC
1999/5/EC
97/23/EC
95/54/EC
90/396/EC
89/686/EC_96/58/EC
87/404/EC

x

2006/42/EC

x

98/37/EC

97/68/EC

Emission No.:

2000/14/EC_2005/88/EC

Annex IV

Notified Body:
Notified Body No.:
Reg. No.:

Annex V
Annex VI

Noise: measured LWA= dB (A); guaranteed LWA= dB (A)
P = KW; L/Ø = cm
Notified Body:

Landau/Isar, den 30.04.2009

First CE: 08 Archive-File/Record: 4465000-39-4155050-08
Art.-No.: 44.650.03 I.-No.: 01019 Documents registrar: Daniel Protschka
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

Weichselgartner/General-Manager Unger/Product-Management

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 9

10

t For EU countries only

Never place any electric tools in your household refuse.

To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its
implementation in national laws, old electric tools have to be separated from other waste and disposed of
in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the demand to return electrical devices:
As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the
device is properly recycled if ownership is relinquished. This can also be done by handing over the used
device to a returns center, which will dispose of it in accordance with national commercial and industrial
waste management legislation. This does not apply to the accessories and auxiliary equipment without
any electrical components which are included with the used device.



The reprinting or reproduction by any other means, in whole or in part,
of documentation and papers accompanying products is permitted only
with the express consent of ISC GmbH.

 Technical changes subject to change

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 10

11

t

GUARANTEE CERTIFICATE

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely
event that your device develops a fault, please contact our service department at the address shown on this
guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under
the service number printed below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.

We do not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the

rectification of these defects or replacement of the device. Please note that our devices have not been
designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated
if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The
following are also excluded from our guarantee: compensation for transport damage, damage caused by
failure to comply with the installation/assembly instructions or damage caused by unprofessional
installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or
current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools
or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies
into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by
the device being dropped) and normal wear resulting from proper operation of the device. This applies in
particular to rechargeable batteries for which we nevertheless issue a guarantee period of 12 months.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

3. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee

claims should be submitted before the end of the guarantee period within two weeks of the defect being
noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee
period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts fitted will not result in an extension of the guarantee period, and no new
guarantee will become active for the work performed or parts fitted. This also applies when an on-site
service is used.

4. In order to assert your guarantee claim, please send your defective device postage-free to the address

shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of
purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if
you could describe the nature of the problem in as much detail as possible. If the defect is covered by our
guarantee then your device will either be repaired immediately and returned to you, or we will send you a
new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the
scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send
the device to our service address.

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 11

EH 05/2009 (01)

Anleitung_BT_MG_180_Kit_SPK7_GB:_ 06.05.2009 14:52 Uhr Seite 12