AKBL400 - AKBL410
PRV : 50 - 1000 Volts
Io : 4.0 Amperes
FEATURES :
*High case dielectric strength
*High surge current capability
*High reliability
*Low reverse current
*Low forward voltage drop
*ldeal for printed circuit board
MECHANICAL DATA :
*Case : Reliable low cost construction utilizing molded plastic technique
*Epoxy : UL94V-O rate flame retardant
*Lead : Axial lead solderable per
MIL - STD 202 , Method 208 guaranteed
*Polarity : Polarity symbols marked on case
*Mounting position : Any
*Weight : 5.15 grams
AVALANCHE BRIDGE
RECTIFIERS
KBL
0.77 (19.56)
0.73 (18.54)
|
|
0.825 (20.95) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
0.605 (15.36) |
|
|
|
|
|
+ |
AC |
AC |
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.052 (1.32) |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.048 (1.22) |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1.00 |
(25.4) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.200 (5.08) |
|
|||||||||||
|
|
|
|
MIN. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.190 (4.82) |
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.265 (6.73 ) |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.085 (2.16) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0.235 (5.97) |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
0.065 (1.65) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dimensions in inches and ( millimeter )
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25 °C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
RATING |
|
SYMBOL |
AKBL |
AKBL |
AKBL |
AKBL |
AKBL |
AKBL |
AKBL |
UNITS |
|
|
|
400 |
401 |
402 |
404 |
406 |
408 |
410 |
|
Maximum Recurrent Peak Reverse Voltage |
VRRM |
50 |
100 |
200 |
400 |
600 |
800 |
1000 |
Volts |
|
Maximum RMS Voltage |
|
VRMS |
35 |
70 |
140 |
280 |
420 |
560 |
700 |
Volts |
Maximum DC Blocking Voltage |
|
VDC |
50 |
100 |
200 |
400 |
600 |
800 |
1000 |
Volts |
Minimum Avalanche Breakdown Voltage at 100 μA |
VBO(min.) |
100 |
150 |
250 |
450 |
700 |
900 |
1100 |
Volts |
|
Maximum Avalanche Breakdown Voltage at 100 μA |
VBO(max.) |
550 |
600 |
700 |
900 |
1150 |
1350 |
1550 |
Volts |
|
Maximum Average Forward Current Tc = 50°C |
IF(AV) |
|
|
|
4.0 |
|
|
|
Amp. |
|
Peak Forward Surge Current Single half sine wave |
|
|
|
|
|
|
|
|
|
|
Superimposed on rated load (JEDEC Method) |
IFSM |
|
|
|
200 |
|
|
|
Amps. |
|
Rating for fusing at ( t < 8.3 ms. ) |
|
I2t |
|
|
|
166 |
|
|
|
A2S |
Maximum Forward Voltage per Diode at IF = 4.0 Amps. |
VF |
|
|
|
1.1 |
|
|
|
Volts |
|
Maximum DC Reverse Current |
Ta = 25 °C |
IR |
|
|
|
10 |
|
|
|
μA |
at Rated DC Blocking Voltage |
Ta = 100 °C |
IR(H) |
|
|
|
1.0 |
|
|
|
mA |
Typical Thermal Resistance (Note1) |
RθJA |
|
|
|
10 |
|
|
|
°C/W |
|
Operating Junction Temperature Range |
TJ |
|
|
- 50 to + 150 |
|
|
°C |
|||
Storage Temperature Range |
|
TSTG |
|
|
- 50 to + 150 |
|
|
°C |
||
|
|
|
|
|
|
|
|
|
|
|
Notes : 1 ) Thermal resistance from Junction to ambient with units mounted on a 3" x 3" x 0.11" ( 7.5 x 7.5 x 0.3 cm ) Cu. plate.
UPDATE : APRIL 21, 1998