Owner’s manual
Free 5 year guarantee
Register your guarantee at
www.dysonairblade.com
Thank you for choosing to buy a Dyson Airblade V™ hand dryer
Dyson customer care
Your Dyson hand dryer is covered for 5 years from the date of purchase, subject to the terms of the limited guarantee.
Register your guarantee now at www.dysonairblade.com
If you have any questions about your hand dryer, call the Dyson Helpline with your serial number and details of where and when you bought the unit.
Note your serial number here for future reference.
Your serial number can be found on your rating plate which is behind the grille on the side of the hand dryer, on a registration sheet in the box, and also on an information sticker on the front of the unit when it is unpacked.
This illustration is for example purposes only.
WARNING
A comprehensive installation guide is enclosed with the hand dryer packaging. This contains detailed information on the correct installation of the unit, which MUST be adhered to completely, including routing of electrical cables. Damage caused by incorrect installation is not covered by your guarantee. Installation MUST be by a qualified electrician.
The instructions in this manual and the installation guide must be followed completely, as failure to do so may result in incorrect operation, damage to property and/or personal injury.
Dyson will not be held liable for any damage to property or personal injury, or any loss of business or revenue, if you, your staff, your installer or service engineers have not followed the instructions given in this manual and the installation guide.
IMPORTANT SAFETY INSTRUCTIONS
BEFORE INSTALLING OR USING THIS UNIT READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THIS MANUAL AND THE INSTALLATION GUIDE
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1.This unit is not intended for use by persons (including children) with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the unit by a person responsible for their safety.
2.Do not allow the hand dryer to be used for any purpose other than drying hands. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
3.Before servicing, switch the power off at the service panel. Ensure the switch is locked to prevent the power from being switched on accidentally. If the means of switching off the power cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
4.Children should be supervised to ensure that they do not play with the unit.
5.Do not use any jetwash equipment for cleaning on or near this unit.
caution
Your hand dryer should be located indoors. Operating temperature range 0°C (32°F) to 40°C (104°F). To reduce the risk of fire or electric shock, do not expose the internal mechanisms/components of this unit to moisture.
READ AND SAVE THESE INSTRUCTIONS
2
Looking after your hand dryer
How to use
1.Place your hands beneath the hand dryer and it will start automatically, creating sheets of air to scrape water from your hands.
2.Move your hands backwards and forwards slowly through the air, turning them over so both back and front are exposed to the airflow.
Troubleshooting Guide
Problem |
Action |
|
|
The hand dryer fails to start. |
Check fuse/circuit breaker is working and that |
|
the power supply is connected. |
|
Turn the unit on and off. |
|
|
The hand dryer sometimes cuts out when in use |
Check the air inlets are clean and free of dust. |
but resumes operation after a period of time. |
If the air inlets are dusty or dirty simply remove |
|
the dust or debris with a soft cloth. |
|
|
The dry time of the hand dryer has increased. |
Inspect the air inlets for dust and remove. |
|
|
The air flow from the hand dryer is running |
Inspect filter and change if required. |
hotter than usual. |
|
|
|
If you have any further questions please contact the Dyson Helpline.
Cleaning
The hand dryer should be cleaned daily.
Follow these 3 simple steps to ensure the unit performs to its best and remains hygienic. Using the wrong cleaning method or product may invalidate your guarantee.
1.Wipe all surfaces with a soft cloth and non-abrasive cleaner.
2.Clean the air inlets on the side REGULARLY.
3.Clean the floor and wall beneath and around the unit. This may be required more regularly in high use areas.
General advice
All cleaning chemicals should be used exactly as indicated by the manufacturer’s instructions (including appropriate dilution).
If a cleaning product is left on the machine for too long, a film will form. This may reduce the effectiveness of the anti-bacterial surfaces.
Any chemicals intended for use should first be tested on an inconspicuous area to confirm suitability.
Aside from cleaning chemicals, care should be taken to avoid any harmful fluids from coming into contact with the unit, in particular oils and alcohol-based products.
Chemical guidelines
Many professional cleaning chemicals can be used. The following are some that are harmful to the unit and should not be used. Use of these will invalidate your guarantee.
Do not use:
Alcohol-acid mixes Alcohol
Solvent /oil-based products Quaternary ammonium Alkali-bleach mixes Foaming ingredients Bleach or abrasive cleaners
Do not pressure wash
Water guidelines
This hand dryer has an IP24 certification.
Use of pressure washers can force water inside the casing. Water damage caused by incorrect cleaning will invalidate your guarantee.
Filter maintenance
Regularly check the air inlets to ensure that they are free from dust and debris. Simply wiping the inlets with a soft cloth should be sufficient to remove dust and debris.
If the air inlets get clogged, further cleaning or a filter change might be required. If required for high usage environments, a Dyson filter change kit provides everything needed to change your unit’s HEPA filter on site. Contact the Dyson Helpline on the number on the back cover of this manual for more information.
3
Loading...