Version 1.30 | 07/04/2016
User Manual
5 Megapixel Day & Night Outdoor Network Camera
DCS-7517
Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or
organization of such revisions or changes.
Manual Revisions
Revision Date Description
1.00 06/29/2015 DCS-7517 Revision A1 with rmware version 1.00
1.10 10/16/2015 Minor updates
1.20 12/24/2015 Minor updates
1.30 07/04/2016 Updated Regulatory Information
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other
countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2016 by D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link
Corporation.
2D-Link DCS-7517 User Manual
Table of Contents
Product Overview .............................................................. 5
Package Contents .........................................................................5
Introduction ................................................................................... 6
System Requirements ................................................................. 7
Features ............................................................................................8
Hardware Overview .....................................................................9
microSD Card Installation ........................................................11
Cable Connectors .......................................................................12
Installation .......................................................................13
Hardware Installation ................................................................13
Assembly and Installation ...............................................13
Cable Connections .....................................................................15
General Connection Using the 12 V DC Power
Adapter ...................................................................................15
Connection Using Power over Ethernet .....................16
Software Installation .................................................................17
Setup Wizard ........................................................................17
Web-based Conguration Utility ..........................................22
Audio and Video ..................................................................32
Video Settings ..................................................................32
Image Settings .................................................................35
Audio Settings .................................................................37
Day and Night Settings .................................................38
Network ..................................................................................39
IP Settings ..........................................................................39
Port and Access Name Settings .................................42
Dynamic DNS ...................................................................45
HTTPS .................................................................................. 46
Access List ..........................................................................48
Advanced Settings .........................................................50
Event Management ...........................................................54
Motion Detection ...........................................................54
Tamper Detection ...........................................................56
DI and DO ..........................................................................57
Event Settings ..................................................................58
Recording ..............................................................................64
Recording Settings .........................................................64
Configuration ...................................................................24
Live Video ......................................................................................24
Client Setup ..................................................................................28
Setup ...............................................................................................29
Basic Setup ............................................................................29
Advanced Setup ..................................................................30
System Overview ........................................................................31
Local Storage ....................................................................66
PTZ Control ...........................................................................68
Digital PTZ .........................................................................68
Lens Control ......................................................................69
System ....................................................................................70
User Settings ....................................................................70
Device Settings ................................................................71
3D-Link DCS-7517 User Manual
Time and Date ..................................................................72
Maintenance .....................................................................73
Parameter List ..................................................................74
Logs .....................................................................................75
Appendix A - Technical Specifications ...........................76
Technical Specications ...........................................................76
Appendix B - Regulatory Information ............................79
Regulatory Information ............................................................79
4D-Link DCS-7517 User Manual
Product OverviewProduct Overview
DCS-7517 5 Megapixel Day & Night Outdoor Network Camera
CAT5 Ethernet Cable
Power Adapter*
CD-ROM with User Manual and Software
Package Contents
Mounting Plate
Alignment Sticker and Fixings Kit
Quick Installation Guide
*Depending on your region, a power adapter may not be included.
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a dierent voltage than the one included with your
product will cause damage and void the warranty for this product.
5D-Link DCS-7517 User Manual
Product Overview
Introduction
D-Link DCS-7517 5 Megapixel Day & Night Outdoor Network Camera is a professional surveillance and security solution for small, medium, and
large enterprises alike. Equipped with an industry-leading 5 megapixel progressive scan CMOS sensor and H.264 compression, the DCS-7517
connects to a network to provide professional high-quality live video over the Internet. This camera is capable of capturing video in both dark
and light environments thanks to its built-in IR LEDs and IR-cut removable (ICR) lter. The ICR lter can be manually applied via the web, or set to
automatically adjust based on lighting conditions. This feature allows the camera to capture crisp color images during the daytime and detailed
grayscale images at night or in or low-light conditions.
The DCS-7517 is equipped with a remote focus lens that controls the iris with extreme precision. It's built-in stepping motor maintains the
iris opening at an optimal level at all times, resulting in superior image clarity and depth of eld as well as image quality. Together with WDR
enhancement, you can identify image details in extremely bright as well as dark environments.
The DCS-7517 is equipped with IP66 certied weatherproof housing designed for both indoor and outdoor applications. The built-in removable
IR-cut lter and IR LEDs give the DCS-7517 the capability to view up to 30 meters at night. The ability to use Power over Ethernet (PoE) also allows
it to be easily installed in a variety of locations without the need for supplemental power cabling. The built-in microSD card slot can be used as a
local backup by storing important events on an easily retrievable microSD card.
The included D-Link D-ViewCam™ is sophisticated software which allows users to manage up to 32 network cameras, set e-mail alert
notications, create recording schedules, and use motion detection to record directly to a hard drive. D-ViewCam™ also allows users to upload a
oor plan to create a realistic layout of the premises where cameras are located, further simplifying the management process.
6D-Link DCS-7517 User Manual
Product Overview
System Requirements
Network Requirements
DCS-7517
Web-based Conguration
Utility Requirements
D-ViewCam Conguration
Utility Requirements
• An Ethernet-based network
Computer with the following:
• Windows®, Macintosh, or Linux-based operating system
• An installed Ethernet adapter
Browser Requirements:
• Internet Explorer® 7 or higher
• Mozilla Firefox 19 or higher
Computer with the following:
• Microsoft Windows® 10/8/7/Vista/XP/2000
• At least 256 MB of memory (512 MB recommended)
• VGA card resolution: SVGA or XGA (1024x768 or above)
• CPU: 1.7 GHz or above (2.8 GHz processor or faster with 512
MB memory and a 32 MB video card is required for multiple
camera viewing and recording in D-ViewCam)
7D-Link DCS-7517 User Manual
Product Overview
Features
Remote Focus Lens
The DCS-7517 allows quick and accurate remote focusing of the lens via the easy-to-use web conguration interface, which ensures that wherever
you are, you can always maintain a sharp and clear image.
DC-iris
The DC-iris lens in the DCS-7517 solves the long-standing problem of capturing sharp images in varying light conditions. The the DCS-7517 optimizes
the iris opening under all lighting conditions, resulting in images with better contrast, clarity, resolution and depth of eld with improved image
sharpness and increased image usability for network video surveillance.
Flexible Connectivity
The DCS-7517 includes input and output ports for connectivity to external devices such as IR sensors, switches, and alarm relays. The DCS-7517
also incorporates Power over Ethernet (PoE), allowing it to be easily installed in a variety of locations without the need for supplemental power
cabling.
High-Quality Video at HD Resolution
The DCS-7517 provides real-time video feeds at up to 15 fps with 2560x1920 resolution and 30 fps with Full HD resolution. H.264 encoding
ensures that images remain crisp, clear, and vivid without taking up too much network bandwidth.
Wide Dynamic Range
Wide Dynamic Range technology neutralizes imperfect lighting, providing clear images with the right amount of contrast even when a subject is
backlit.
Weatherproof with Tamper Detection
Designed to be mounted outdoors, the DCS-7517 includes an IP66 certied enclosure which protects against the elements. Anti-tamper features
make this camera suitable for tamper-prone locations such as transportation hubs, schools, or correctional facilities. The electronic tamper
detection system can sense whenever the camera has been redirected, de-focused, blocked, or spray-painted, and can respond promptly with a
visible or audible alarm.
Remote Monitoring Utility
The D-ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to congure and access
the Network Camera from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive,
viewing up to 32 cameras on one screen, and taking snapshots.
8D-Link DCS-7517 User Manual
Product Overview
1
Hardware Overview
2
6
4
3
1 Weatherproof Casing The camera is housed in an IP66 certied weatherproof casing, which protects it against rain and dust.
2 IR LEDs Infrared LEDs illuminate the camera's eld of view at night.
Red: The camera is receiving power but does not have a network connection.
3 Power/Status LED
4 Camera Lens Varifocal lens to record video of the surrounding area.
5 Light Sensor The light sensor measures the lighting conditions and switches between color and infrared accordingly.
6 microSD Card Cover Unscrew to remove/change the camera's microSD card.
Green: The camera is receiving power and has a network connection.
Flashing Green: The camera is transmitting data across the network.
5
9D-Link DCS-7517 User Manual
Product Overview
Hardware Overview
4
2
1
1 Sunshield Shields the camera sensor from direct sunlight.
2 Adjustment Screw
3 Camera Shoe Adjustable mounting seat.
4 Wire in Bracket Assembles tightly and protects the cables from outdoor wear and tear.
Allows repositioning of the sunshield.
3
10D-Link DCS-7517 User Manual
Product Overview
microSD Card Installation
Open the microSD Card Cover
Unscrew the microSD card cover and pull it down to open it.
Install the microSD Card
Push the microSD card into the camera with the gold contacts oriented towards the base of the camera. To eject, push the microSD card into
the slot.
Note: Make sure that the weatherproof seals are secured rmly in place when reattaching the microSD card cover.
11D-Link DCS-7517 User Manual
Product Overview
Cable Connectors
1 4 532 6 7
1 Power Connector Power connector for the provided 12V DC power adapter.
2 Audio In (Red) Connects to a microphone.
3 Audio Out (Green)
4 BNC Connector
5 Reset Button
6 DI/DO Connector
7 Ethernet Jack
Connects to a speaker.
The BNC connector is recommended for use with handheld monitors to
check the camera's eld of view during installation.
Press and hold the recessed button for 10 seconds to reset the camera back to
the factory default settings.
I/O connectors for external devices.
Connects to an RJ45 Ethernet port. Can be used with PoE to provide power to
the camera.
12D-Link DCS-7517 User Manual
InstallationInstallation
Hardware Installation
Assembly and Installation
It is highly recommended that you congure and test your camera before mounting it.
Step 1
Place the alignment sticker where you want to position the camera. Make sure the camera base will be positioned so that the cable channel is on
the bottom.
Step 2
Use a 6 mm drill bit to make the required holes approximately 25 mm deep, then insert the wall anchors into the holes.
If you are running the camera cables through the wall, drill a hole in the center and pull the cables through the hole.
Step 3
Use the screws provided to mount the camera to the wall.
If you are running the camera cables out the side of the camera, guide the camera cables through the cable channel on the base.
Step 4
Connect the power and Ethernet cables, or just the Ethernet cable if you are using a PoE connection.
Alignment sticker
13D-Link DCS-7517 User Manual
Installation
If the cable bundle is not required, it can be detached from the camera, and the socket sealed with a weatherproof cable cover.
To adjust the camera's angle, turn the adjustment ring counterclockwise to loosen it, then move the camera to the desired position and angle.
When you are nished, turn the adjustment ring clockwise to tighten it.
14D-Link DCS-7517 User Manual
Installation
Cable Connections
General Connection Using the 12 V DC Power Adapter
Step 1
Connect the network camera to a switch via an Ethernet cable.
Step 2
Connect the supplied power adapter to the camera's power connector, then plug the adapter into a power outlet.
15D-Link DCS-7517 User Manual
Installation
Connection Using Power over Ethernet
Step 1
If you are using a PoE switch, connect the IP camera to the PoE switch via an Ethernet cable, which will provide transmission
of both power and data over a single cable.
16D-Link DCS-7517 User Manual
Installation
Software Installation
Setup Wizard
Insert the DCS-7517 CD into your computer's CD-ROM drive to begin the installation. If the Autorun function on your computer is disabled, or if
the D-Link Launcher fails to start automatically, click the Start button and type D:\autorun.exe (where D: represents the drive letter of your CDROM drive) and press Enter.
Click Setup Wizard to begin the installation.
After clicking Setup Wizard, the window on the right will open.
Click Next to continue.
17D-Link DCS-7517 User Manual
Installation
Click Yes to accept the License Agreement.
Click Next to start the installation process.
Note: The installation may take several minutes to nish.
18D-Link DCS-7517 User Manual
Installation
Click Finish to complete the installation.
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start
menu.
Start > D-Link > Setup Wizard SE
19D-Link DCS-7517 User Manual
Installation
The Setup Wizard will appear and display the MAC address and IP address of your
camera(s). If you have a DHCP server on your network, a valid IP Address will be
displayed. If your network does not use a DHCP server, the network camera's default
static IP address (192.168.0.20) will be displayed.
Select your camera and then click the Wizard button to continue.
Enter the Admin ID and password. When logging in for the rst time, the default
Admin ID is admin with the password left blank.
Click Next to continue.
20D-Link DCS-7517 User Manual
Installation
Select DHCP if your camera obtains an IP address automatically from a DHCP server
such as a router. Select Static IP if you want to manually enter the IP settings for the
camera.
Click Next to continue.
Take a moment to conrm your settings and click Restart.
21D-Link DCS-7517 User Manual
Installation
Web-based Conguration Utility
This section explains how to congure your new D-Link Network Camera using the Web-based Conguration Utility.
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start
menu.
Start > D-Link > Setup Wizard SE
Select the camera and click Link to access the web conguration.
The Setup Wizard will automatically open your web browser to the IP address of the
camera.
22D-Link DCS-7517 User Manual
Installation
Enter admin as the default username and leave the password blank. Click OK to
continue.
This section shows your camera’s live video. You can select your video prole and
view or operate the camera.
23D-Link DCS-7517 User Manual
CongurationConguration
Live Video
When you connect to the camera's web interface you will see the following page. This is the Live Video page which will allow you to view the
camera's video feed and control basic camera functions using the icons on the screen. Please refer to the tables on the following pages for
detailed information about the icons on this screen.
24D-Link DCS-7517 User Manual
Conguration
Client Settings
Language
Setup
Digital Output
Video Stream
Global View
Set up the stream transmission mode and saving options on the local
computer.
Select this option to adjust the language settings.
Click to edit the camera's settings. Note that only Administrators can
access the setup page. To simplify the setting procedure, two types of
user interfaces are available: Advanced Setup for professional users
and Basic Setup for entry-level users.
Click this button to turn the digital output device on or o.
This camera supports multiple streams (stream 1 ~ 3) simultaneously.
You may select one for live viewing.
Click on this item to display the Global View window. The Global
View window contains a full view image (the largest frame size of
the captured video) and a oating frame (the viewing region of the
current video stream). The oating frame allows users to control the
e-PTZ function (Electronic Pan/Tilt/Zoom). For more information
about e-PTZ operation, please refer to PTZ Control on the next page.
For more information about how to set up the viewing region of the
current video stream, please refer to Video settings on page 32.
25D-Link DCS-7517 User Manual
Conguration
PTZ Control
ePT Direction
Zoom
Focus
Auto Focus/Home
This camera supports both digital (e-PTZ) and mechanical zoom
control.
Mechanical Z: Controls the mechanical zoom.
Digital PTZ: Controls the e-PTZ operation.
Home: Moves the camera to the preset home position.
Direction: Controls the camera’s pan or tilt directions (up/down/left/
right).
Zoom in: Zooms into the image.
Zoom out: Zooms out of the image.
Control camera focus to get a clear image. (Only available under
Mechanical PTZ mode)
Focus Near: Sets the depth of eld zone closer.
Focus Far: Sets the depth of eld zone farther.
Reset the camera focus, either by auto focus or to a pre-congured
default.
Auto Focus: Allows the camera to automatically adjust the focus.
Home: Returns to the center of the viewing area.
Patrol: Moves through a pre-dened sequence of pan, tilt, zoom, and
focus settings. Before selecting this, you must dene at least two preset
points.
Digital PTZ
Control Panel
Mechanical Z
Control Panel
Patrol Auto Pan
Go Preset
Speed Control
Auto Pan: Automatically scans an area horizontally.
Stop: Stops patrol and auto pan.
Select a preset from the drop-down list to quickly move the camera to
the desired preset position.
Control Pan/Tilt/Zoom speed: Please select a value between 0 and 10.
0 is the slowest and 10 is the fastest.
Pan Speed Control
Tilt Speed Control
Zoom Speed Control
26D-Link DCS-7517 User Manual
Conguration
Recording Folder
Two Way Audio
Snapshot
Recording
Digital Zoom
Mic Volume
Click this button to capture and save still images. The captured images will be displayed in a pop-up window. Right-click the
image and select Save Picture As to save it in JPEG (*.jpg) or BMP (*.bmp) format.
Click this button to record video clips to your computer. When close your web browser, video recording stops accordingly.
Specify a storage destination for the recorded video les.
Click and uncheck “Disable digital zoom” to enable the zoom operation. The navigation screen indicates the part of the
image being magnied. To control the zoom level, drag the slider bar. To move to a dierent area you want to magnify, drag
the navigation screen.
Click this button to enable or disable two way audio communication.
Click this button to raise or lower the volume of the attached microphone.
Mic Mute
Speaker Volume
Speaker Mute
Full Screen
Zoom ratio
Help
Click this button to completely mute the attached microphone.
Click this button to raise or lower the volume of the attached speaker.
Click this button to completely mute the attached speaker.
Click this button to switch to full screen mode. Press the “Esc” key to switch back to normal mode.
Auto: The video zoom ratio will be changed automatically according to viewing window size.
100%: Keep the video zoom ratio at 100%
50%: Keep the video zoom ratio at 50%
25%: Keep the video zoom ratio at 25%
Click the Help button to learn the detailed information regarding camera setup and solve any problems you encounter.
27D-Link DCS-7517 User Manual
Conguration
Client Setup
Clicking the Client Settings button will bring you to the following screen which
allows you to congure the basic protocol options for your camera.
H.264 Media Options
For additional information about streaming options please refer to "Audio and
Video" on page 32.
Recording Options
Folder: Select the folder where you would like the Recording le saved on your
computer.
File name prex: Enter a le name prex for the Recording les.
Add date and time sux to le name: Select this checkbox if you would like the
date and time to be added to the end of each lename.
Local Streaming Buer Time
Enter the buer time in milliseconds. The buer will cause a slight delay between
live activity and the video of the live stream but may increase the quality of video.
28D-Link DCS-7517 User Manual
Conguration
Setup
The DCS-7517 includes basic and advanced setup screens. Both screens include a tree view with multiple setup options. This manual includes
detailed explanations for all advanced setup screens.
Basic Setup
Click the Setup button to enter the setup screen.
Click on the Basic button to enter the Basic Setup screen.
Please click the [+] next to each folder to view the options inside.
Basic Setup includes the following options:
System Overview
Audio and Video
- Video Settings
- Audio Settings
Network
- IP Settings
Event Management
- Motion Detection
- Tamper Detection
PTZ Control
- Digital PTZ
System
- User Settings
- Device Settings
- Time and Date
- Maintenance
29D-Link DCS-7517 User Manual
Conguration
Advanced Setup
Click the Setup button to enter the setup screen.
Click on the Advanced button to enter the Advanced Setup screen.
Please click the [+] next to each folder to view the options.
Advanced setup includes the following options:
System Overview
Audio and Video
- Video Settings
- Image Settings
- Audio Settings
- Day and Night Settings
Network
- IP Settings
- Port & Access Name Settings
- Dynamic DNS
- HTTPS
- Access List
- Advanced Settings
Event Management
- Motion Detection
- Tamper Detection
- DI and DO
- Event Settings
Recording
- Recording Settings
- Local Storage
PTZ Control
- Digital PTZ
- Lens Control
System
- User Settings
- Device Settings
- Time and Date
- Maintenance
- Parameter List
- Logs
30D-Link DCS-7517 User Manual
Conguration
System Overview
The system overview page contains a summary of the camera's current settings.
31D-Link DCS-7517 User Manual
Conguration
Audio and Video
Video Settings
This page allows you to set up three video streams to be displayed on a computer, mobile device, or storage system. Each stream has
independent options for compression type, frame size, frame rate to optimize the bandwidth utilization and video quality.
Video Options
Viewing Window: The camera supports multiple streams with frame sizes ranging
from 960x540 to 2560x1920. Click Viewing Window to open the viewing region
setting page. On this page, you can set the Region of Interest (ROI) and the Output
Frame Size for stream 1~3.
Please follow the steps below to set up a stream:
1. Select a stream with a viewing region you would like to set.
2. Select a Region of Interest from the drop-down list, and the oating frame will
resize accordingly. If you want to set up a customized viewing region, you can
also resize and drag the oating frame to a desired position with your mouse.
3. Choose an Output Frame Size from the drop-down list according to the size of
your monitoring device.
Note: The “Output Frame Size” you choose should not be greater than the selected
“Region of Interest".
Dening the streams:
Stream 1-3: You can dene the "Region of Interest" (viewing region) and the
"Output Frame Rate" (size of the live view window) for each stream.
32D-Link DCS-7517 User Manual
Conguration
After adjusting settings for the Viewing Window, click Save to enable the settings
and click Close to exit the window. The selected Output Frame Size will immediately
be applied to the frame size of video stream. You can then go back to the Live Video
page to test the new settings.
Sensor Setting: Click Sensor Setting to open the Sensor Setting page. On this
page, you can set the maximum exposure time, exposure level, and AGC (Auto Gain
Control) settings. You can congure two sets of sensor settings: one for normal
situations, and one for special situations such as when using day/night/schedule
mode.
Exposure
• Maximum Exposure Time: Select the desired maximum exposure time based
on the lighting conditions of the area being monitored. Longer exposure times
will improve exposure for dark environments, but may result in moving objects
appearing blurred. The maximum exposure time can be set to 1/120 second,
1/60 second, 1/30 second, 1/15 second, or 1/5 second.
• Exposure level: You can manually set the Exposure level from 1 to 8 (dark to
bright).
• Max. Gain (Auto Gain Control): You can manually set the AGC level to 2X, 4X,
8X, 16x, or 32x. The higher the value, the more gain will be applied and the
brighter the image will be.
You may click Preview to ne-tune the image, or click Restore to recall the previous
settings without saving your changes. When you are nished changing the settings
on this page, click Save to save your changes and click Close to exit the page. If you
want to congure another sensor setting for day/night/schedule mode, please click
Prole 2 and follow the steps below to setup:
1. Click Enable this prole.
2. Select the mode to use: Day mode, Night mode, or Schedule mode. Please
manually enter a range of time if you choose Schedule mode.
3. Congure the Exposure settings in the second column.
4. Click Save to save your changes and click Close to exit the page.
33D-Link DCS-7517 User Manual
Conguration
Aspect Ratio
Choose either 4:3 or 16:9 for the aspect ratio. This will format the video stream
to better t the type of display that it will be viewed on. 4:3 is better for standard
denition displays, while 16:9 is meant for displays that are capable of showing wide
format content.
Video Quality Settings for Stream 1~3
Compression Type: The compression level aects the amount of bandwidth and
storage required. Lower compression uses more bandwidth and storage but delivers
better image quality. Of the two options, H.264 consumes much less network
bandwidth compared to JPEG.
Frame Size: Select a frame size from the drop-down menu; a bigger frame size
requires more bandwidth and storage. For smaller viewers such as mobile phones, a
smaller frame size and lower frame rate is recommended.
Frame Rate: This option aects the smoothness of the video. Higher frame rates
provide smoother video quality but require more storage. You can set the frame rate
to customize, 1, 2, 3, 5, 8, 10, 15, 20, 25, or 30 fps. The frame rate may automatically
change and some options may not be available depending on the resolution. The
max. frame rate when using a 4:3 aspect ratio is 15 fps.
Intra Frame Period: Sets the interval between I-frames. The shorter the interval,
the more likely you will get better video quality, but at the cost of higher network
bandwidth consumption. You can set the intra frame period to 1/4 second, 1/2
second, 1 second, 2 seconds, 3 seconds, or 4 seconds.
Video Quality: This setting limits the maximum refresh frame rate.
• Constant bit rate: Sets a xed bandwidth regardless of the video quality. Select
Constant bit rate and a bandwidth from 20 Kbps to 8Mbps. You can also select
Customize and manually enter a value.
• Fixed quality: Optimizes bandwidth utilization and video quality. The video
quality can be adjusted to one of the following settings: Medium, Standard, Good,
Detailed, or Excellent. You can also select Customize and manually enter a value.
34D-Link DCS-7517 User Manual
Conguration
Image Settings
This page allows you to tune the white balance, brightness, saturation, contrast, and
sharpness settings for the video.
Color: Select either a Color or B/W (black and white, monochrome) video display.
Power Line Frequency: Select either 50 or 60 Hz depending on your region.
Iris Mode: Select the environment that the camera will primarily be viewing. This
can be set to Fixed, Indoor, or Outdoor.
Video Orientation: Flip will vertically rotate the video. Mirror will horizontally rotate
the video. You may select both options if your camera is installed upside down.
White Balance: This adjusts the relative amount of red, green, and blue primary
colors in the image so that neutral colors are reproduced correctly.
• Auto: The camera automatically adjusts the color temperature of the light in
response to dierent light sources. The white balance setting defaults to Auto
and works well in most situations.
• Fixed: Follow the steps below to manually set the white balance to compensate
for ambient lighting conditions:
1. Set the White balance to Auto and click Save.
2. Place a sheet of white paper in front of the lens, then allow the camera to
adjust the color temperature automatically.
3. Select Fixed to conrm the setting while the white balance is being
measured.
4. Click Save to enable the new setting.
35D-Link DCS-7517 User Manual
Conguration
Brightness: Adjusts the image brightness level.
Saturation: Adjusts the image saturation level.
Contrast: Adjusts the image contrast level.
Sharpness: Adjusts the image sharpness level.
Overlay Title and Time Stamp on Video: Select this option to place the video title
and time on the video streams. (When the frame size is set to 176 x 144, only the
time will be stamped on the video streams.)
Privacy Mask: Here you can block out certain sensitive zones for privacy concerns.
To set up a Privacy Mask Window, follow the steps given below:
1. Click New to add a window.
2. The height and width of the window can be resized by drag-and-dropping
the window.
3. Enter a descriptive name for the window and click Save to apply the
changes.
4. Select Enable privacy mask to enable this function.
None:
• Up to 5 privacy mask windows can be set up on the same screen.
• If you want to delete a privacy mask window, please click the ‘x’ at the upper
right-hand corner of the window.
Enable WDR: Enabling Wide Dynamic Range (WDR) can improve the exposure of
the image when the lighting in the area varies signicantly.
WDR Level: Specify a value from 0 to 10 to specify how much WDR to apply to the
image.
36D-Link DCS-7517 User Manual
Conguration
Audio Settings
This page allows you to congure the settings for the built-in audio support.
Mute: Check this box to mute all of the audio capabilities of the camera.
Microphone Input Gain: The microphone sensitivity can be increased or decreased
to help provide better audio quality.
AAC bit Rate: Select the desired bit rate for the AAC audio codec.
G711 bit Rate: Select the desired bit rate for the G711 audio codec.
37D-Link DCS-7517 User Manual
Conguration
Day and Night Settings
Switch to B/W in Night Mode: Select to automatically enable the camera to switch
to black and white when in night mode.
IR Cut Filter: The IR-Cut Removable (ICR) lter mechanically switches between two
dierent sensor lters. It provides the best light conditions both during the day and
night. The following options are:
• Auto Mode: The camera automatically switches between day and night mode
based on the level of ambient light.
• Day Mode: In this mode, the camera switches on the IR cut lter at all times,
which will block infrared light from reaching the sensor so that colors are not
distorted.
• Night Mode: The camera switches o the IR cut lter to allow infrared light to
pass through. This helps the camera use all available light to see more clearly in
low light conditions.
• Synchronize with Digital Input: The camera automatically removes the IR cut
lter when a DI input is triggered.
• Schedule Mode: The camera switches between day and night mode based on
a specic schedule. Enter the starting and ending time to use for day mode;
during all other times, the camera will use night mode. Note that the time
format is [hh:mm] and is expressed in 24-hour time. By default, the starting and
ending times for day mode are set to 07:00 and 18:00.
Light Sensor Sensitivity: The light sensor determines when to switch between day
mode and night mode when the IR Cut Filter setting is set to Auto Mode. Select
Low, Normal, or High sensitivity for the light sensor.
38D-Link DCS-7517 User Manual
Conguration
Network
IP Settings
IPv4
LAN: Select this option when the camera is deployed on a local area network (LAN)
and is intended to be accessed by local computers. The default setting for the
Network Type is LAN. Remember to click Save after making any changes.
• Get IP address automatically (DHCP): Select this connection if you have a DHCP
server such as a router running on your network and would like a dynamic IP
address to be assigned to the camera automatically.
• Use xed IP address: You may enter a static or xed IP address for your camera.
When selected, these options will appear:
IP Address: Enter an IP address.
Subnet Mask: The default value is “255.255.255.0.” This helps to determine if
the designated IP address is on the same subnet.
Default Router: This is the gateway used to forward frames to destinations
in a dierent subnet. (Invalid router settings will cause a transmission to fail
if its destination is in a dierent subnet).
Primary DNS: The Primary Domain Name Server (DNS) that translates a
hostname into an IP address.
Secondary DNS: The Secondary Domain Name Server (DNS) that is used as a
backup for the Primary DNS.
Primary WINS Server: The primary WINS server that maintains the database
of computer names and IP addresses.
Secondary WINS Server: The secondary WINS server that maintains the
database of computer names and IP addresses.
39D-Link DCS-7517 User Manual
Conguration
• Enable UPnP Presentation: Select this option to enable UPnP presentation for
the camera so that when the camera is connected to your network, a shortcut
to it will be listed in My Network Places. To utilize this feature, please make sure
that UPnP is installed and enabled on your computer.
• Enable UPnP Port Forwarding: To access the camera from the Internet, select
this option to allow the camera to open ports on the router automatically so
that video streams can be sent out from your network. To utilize this feature,
make sure that your router supports UPnP and it is activated.
PPPoE: Select this option to congure the camera to connect directly to a PPPoE
Internet connection (such as through a DSL modem) and make it accessible from
anywhere over the Internet. Note that this feature requires an account provided by
your ISP.
Follow the steps below to acquire the camera’s public IP address.
1. Set up the camera on your network.
2. Go to Live View > Setup > Event management > Event settings > Server
Settings (refer to Server Settings to add a new e-mail address or FTP server)
3. Go to Setup > Event management > Event settings > Media Settings (please
refer to Media Settings). Select System log so that you will receive system logs
with the camera’s public IP address in your e-mail inbox or on your FTP server.
4. Go to Setup > Network > IP settings. Select PPPoE and enter the user name and
password provided by your ISP. Click Save to enable the setting.
5. The camera will reboot.
6. Disconnect the power to the camera. Remove it from your network and connect
it to your DSL modem or PPPoE Internet connection.
7. You can now access your camera through the public IP address, which will be in
the system logs sent to your e-mail inbox or FTP server.
40D-Link DCS-7517 User Manual
Conguration
IPv6
Enable IPv6: Select this option and click Save to enable IPv6. Please note that this
only works if your network environment and hardware equipment support IPv6.
The browser used should be Internet Explorer 8 or Firefox 19 (or above).
When IPv6 is enabled, by default, the camera will listen to router advertisements
and will be assigned a link-local IPv6 address accordingly.
IPv6 Information: Click this button to obtain IPv6 information for your camera. If
your IPv6 settings work successfully, the IPv6 address list will be listed in the pop-up
window.
Please follow the steps below to link to an IPv6 address:
1. Open your web browser.
2. Enter the link-global or link-local IPv6 address in the address bar of your web
browser.
3. Press Enter on the keyboard or click the Refresh button to refresh the webpage.
DHCPv6: Enable this function if you have a DHCPv6 server running on your network
and would like a dynamic IPv6 address to be assigned to the camera automatically.
Manually Setup the IP address: Select this option to manually congure your
IPv6 settings if your network environment does not have a DHCPv6 server or
advertisements-enabled routers.
41D-Link DCS-7517 User Manual
Conguration
Port and Access Name Settings
HTTPS
By default, the HTTPS port is set to 443. It can also be assigned to another port
number between 1025 and 65535.
HTTP
By default, the HTTP port is set to 80 and the secondary HTTP port is set to 8080.
They can also be assigned to another port number between 1025 and 65535.
Authentication: Depending on your network security requirements, the camera
provides two types of security for an HTTP transaction: basic and digest. If basic
authentication is selected, the password is sent in plain text format and carries the
potential risk of your trac being intercepted. If digest authentication is selected,
user credentials are encrypted using the MD5 algorithm and thus provide better
protection against unauthorized access.
Access name for stream 1 ~ 3: The Network camera supports multiple streams
simultaneously. The access name is used to dierentiate between streaming
sources. You can click Setup > Video > Video Settings to set up the video quality of
linked streams.
RTSP
To utilize RTSP streaming authentication, make sure that you have set a password
for the camera rst. Please refer to User Settings for details.
42D-Link DCS-7517 User Manual
Conguration
Authentication: Depending on your network security requirements, the camera
provides three types of security settings for streaming via RTSP: disable, basic,
and digest. If basic authentication is selected, the password is sent in plain text
format and carries the potential risk of your trac being intercepted. If digest
authentication is selected, user credentials are encrypted using the MD5 algorithm
and thus provide better protection against unauthorized access.
Access Name for Stream 1 ~ 3: This camera can deliver multiple streams
simultaneously. The access name is used to dierentiate between streaming
sources. If you want to use an RTSP player to access the camera, you have to set the
video mode to H.264 and use an RTSP URL to request transmission of the stream.
For example, "rtsp://[your camera IP]/live1.sdp" would be the RTSP URL for stream 1.
Multicast and Unicast Streaming Protocols
You may choose to enable multicast or unicast for your camera's audio and video
streaming so that your camera can establish connections with clients to send and
receive content.
43D-Link DCS-7517 User Manual
Conguration
Unicast video transmission delivers a stream through point-to-point transmission.
Multicast, on the other hand, sends a stream to the multicast group address and
allows multiple clients to acquire the stream at the same time by requesting a copy
from the multicast group address. As a result, enabling multicast can save network
bandwidth.
Multicast Group Address: An IP Multicast group address is used to send and receive
content. Sources use this group address as the destination address while sending
their data packets. Receivers use this group address to inform the network that they
are interested in receiving packets sent to that group.
Multicast Video Port: The ports can be changed to values between 1025 and
65535. The multicast RTP port must be an even number, and the multicast RTCP
port number is the multicast RTP port number plus one, and thus is always
odd. When the multicast RTP port changes, the multicast RTCP port will change
accordingly.
Multicast TTL [1~255]: The multicast TTL (Time To Live) is the value that tells the
router the range that a packet can be forwarded.
Click an item to display its detailed conguration information. Select the Always
multicast option to enable multicast for stream 1 ~ 3.
44D-Link DCS-7517 User Manual
Conguration
Dynamic DNS
This section explains how to congure your camera for a dynamic domain name
service. DDNS is a service that allows your camera, especially when assigned with
a dynamic IP address, to have a xed host and domain name. With a Dynamic DNS
account, the camera automatically updates your IP address with your DDNS server.
Enable DDNS: Select this option to enable DDNS.
Server Name: Select a DDNS server name from the provider drop-down list to ll in
the Host Name automatically, or enter your host information.
Host Name: Enter the host name of the DDNS server.
Username: Enter the username or e-mail you use to connect to the DDNS server.
Password: Enter the password you use to connect to the DDNS server.
Status: Displays the current connection status.
45D-Link DCS-7517 User Manual
Conguration
HTTPS
This section explains how to enable authentication and encrypted communication
over SSL (Secure Socket Layer). It provides security to help protect streaming data
transmission over the Internet.
Enable HTTPS
Select to enable HTTPS communication, then select HTTP & HTTPS or HTTPS only
for the connection method. Note that you have to create and install a certicate rst
in the second column before clicking the Save button.
Create and Install Certicate Method
Before using HTTPS for communication with the camera, a certicate must be
created.
There are three ways to create and install a certicate:
Create Self-signed Certicate Automatically
1. Select this option.
2. In the rst column, select Enable HTTPS secure connection, then select a
connection option: “HTTP & HTTPS” or “HTTPS only”.
3. Click Save to generate a certicate.
4. The Certicate Information will automatically be displayed in the third column.
You can click Property to view detailed information about the certicate.
5. Click Live Video to return to the main page. Change the address from “http://”
to “https://“ in the address bar and press Enter. Some Security Alert dialogs will
pop up. Click OK or Yes to enable HTTPS.
Create Self-signed Certicate Manually
1. Click Create to open the Create Certicate page, then click Save to generate the
certicate.
2. The Certicate Information will automatically be displayed in the third column
as shown. You can click Property to see detailed information about the
certicate.
46D-Link DCS-7517 User Manual
Conguration
Create Certicate Request and Install
Select this option to create a certicate from a certicate authority.
1. Click Create to open the Create Certicate page, then click Save to generate
the certicate.
2. If you see the information bar, click OK and click on the Information bar at the
top of the page to allow pop-up.
3. The pop-up window shows an example of a certicate request.
4. Look for a trusted certicate authority that issues digital certicates. Enroll the
camera.
Wait for the certicate authority to issue a SSL certicate. Click Browse... to search
for the issued certicate, then click Upload in the second column.
How do I stop using HTTPS for my camera?
1. Deselect Enable HTTPS secure connection in the rst column and click Save. A
warning dialog will pop up.
2. Click OK to disable HTTPS.
3. You will be redirected to a non-HTTPS page automatically.
If you want to create and install other certicates, please remove the existing one.
To remove the signed certicate, deselect Enable HTTPS secure connection in the
rst column and click Save, then click Remove to erase the certicate.
47D-Link DCS-7517 User Manual
Conguration
Access List
This section explains how to control access permissions by verifying the connecting
client PC’s IP address.
General Settings
Maximum number of concurrent streaming connection(s) limited to: Allows
simultaneous live viewing for 1~10 clients (including stream 1 ~ stream 3). The
default value is 10. If you modify the value and click Save, all current connections
will be disconnected and will automatically attempt to reconnect.
View Information: Click this button to display a connection status window that
shows a list of the current connections.
• IP address: Current connections to the camera.
• Elapsed time: How much time the client has been on the webpage.
• User ID: If the administrator has set a password for the webpage, clients must
enter a user name and password to access the live video. The user name will be
displayed in the User ID column. If the administrator allows clients to link to the
webpage without a user name and password, the User ID column will be empty.
There are some situations which allow clients access to the live video without a user
name and password:
1. The administrator did not set up a user password. For more information about
how to set up a user password and manage user accounts, please refer to User
Settings.
2. The administrator has set up a user password, but set RTSP Authentication to
“disable“. For more information about RTSP Authentication, please refer to RTSP
Streaming.
• Refresh: Click this button to refresh all current connections.
• Add to deny list: You can select entries from the Connection Status list and add
them to the Deny List to deny access. Please note that the selected connections
will only be disconnected temporarily and will automatically try to reconnect. If
you want to enable the denied list, please select Enable access list ltering and
click Save in the rst column.
48D-Link DCS-7517 User Manual
Conguration
Disconnect: If you want to break o the current connections, please select them
and click this button. Please note that the selected connections will only be
disconnected temporarily and will automatically try to reconnect.
Enable Access List Filtering: Select this item and click Save if you want to enable
the access list ltering function.
Filter Type
Select Allow or Deny as the lter type. If you choose Allow, only those clients
whose IP addresses are on the Access List below can access the camera, and
all others will not. On the contrary, if you choose Deny, those clients whose IP
addresses are on the Access List below will not be allowed to access the camera,
and all others will.
Note: If you choose Allow, make sure you enter the IP address of the computer
you are using to congure your camera before clicking Save, or else you may be
blocked from accessing the camera.
Filter
You can add a rules to the Access List. Please note that the IPv6 access list
column will not be displayed unless you enable IPv6 on the Network page. For
more information about IPv6 Settings, please refer to Enable IPv6 for detailed
information.
There are three types of rules:
Single: This rule allows you to add an IP address to the Access List.
Network: This rule allows you to assign a network address and corresponding
subnet mask to the Access List.
Range: This rule allows you to assign a range of IP addresses to the Access List
(IPv4 only).
Administrator IP address
Always allow the IP address to access this device: Select this item and add the
Administrator’s IP address in this eld to make sure the Administrator can always
connect to the device.
49D-Link DCS-7517 User Manual
Conguration
Advanced Settings
SNMP conguration
This section explains how to use SNMP on the network camera. The Simple
Network Management Protocol is an application layer protocol that facilitates the
exchange of management information between network devices. It helps network
administrators to remotely manage network devices, and to nd and solve network
problems with ease.
SNMP consists of the following three key components:
1. Manager: Network-Management Station (NMS), a server which executes
applications that monitor and control managed devices.
2. Agent: A network-management software module on a managed device which
transfers the status of managed devices to the NMS.
3. Managed device: A network node on a managed network. For example: routers,
switches, bridges, hubs, computer hosts, printers, IP telephones, network
cameras, web server, and database.
Before conguring SNMP settings on this page, please enable your NMS rst.
Enable SNMPv1, SNMPv2c: Select this option and enter the names of the Read/
Write community and Read Only community according to your NMS settings.
Enable SNMPv3: This option enables cryptographic security, which allows you to
set an Authentication password and Encryption password for stronger security.
• Security name: Enter the community name according to your NMS settings.
• Authentication type: Select MD5 or SHA as the authentication method.
• Authentication password: Enter the password for authentication (at least 8
characters).
• Encryption password: Enter a password for encryption (at least 8 characters).
50D-Link DCS-7517 User Manual
Conguration
IEEE 802.1x
Enable this function if your network environment uses IEEE 802.1x, which is a portbased network access control. The network devices, any intermediary switch/access
point/hub, and RADIUS server must support 802.1x and have it enabled.
The 802.1x standard is designed to enhance the security of local area networks,
which provides authentication to network devices (clients) attached to a network
port (wired or wireless). If all certicates between client and server are veried,
a point-to-point connection will be enabled. If authentication fails, access on
that port will be prohibited. 802.1x utilizes an existing protocol, the Extensible
Authentication Protocol (EAP), to facilitate communication.
Please follow the steps below to enable 802.1x:
1. Before connecting the camera to a protected network with 802.1x, apply for a
digital certicate from a Certicate Authority (i.e., MIS of your company) that can
be validated by a RADIUS server.
2. Connect the camera to a PC or notebook outside of your protected LAN. Open
the conguration page of the camera. Select EAP-PEAP or EAP-TLS as the EAP
method. In the following elds, enter the ID and password issued by the CA,
then upload the related certicate(s).
3. When all the settings are complete, move the camera to the protected LAN
by connecting it to an 802.1x enabled switch. The devices will then start the
authentication automatically.
51D-Link DCS-7517 User Manual
Conguration
QoS (Quality of Service)
Quality of Service refers to a resource reservation control mechanism, which
guarantees a certain quality of transmission to dierent services on the network.
Quality of service guarantees are important if the network capacity is insucient,
especially for real-time streaming multimedia applications. It gives you the ability
to prioritize trac and guarantee a certain level of performance. It can also help
you control the amount of bandwidth each application may use, and thus provide
higher reliability and stability for your network.
Requirements for QoS:
To utilize QoS in a network environment, the following requirements must be met:
• All network switches and routers in the network must include support for QoS.
• The network video devices used in the network must have QoS enabled.
CoS
IEEE802.1p denes a QoS model at OSI Layer 2 (Data Link Layer), which is called
CoS, Class of Service. It adds a 3-bit value to the VLAN MAC header, which indicates
prioritization from 0~7 (eight dierent classes of service are available). The priority
is set up on the network switches, which then use dierent queuing disciplines to
forward the packets.
Please follow the steps below to enable CoS:
1. Click Enable CoS.
2. Enter the VLAN ID of your switch (0~4095).
3. Choose the priority for each application (0~7). Higher values will provide higher
priority.
Note:
• A VLAN Switch (802.1p) is required. Web browsing may fail if the CoS settings
are incorrect.
• Class of Service technologies do not guarantee a level of service in terms of
bandwidth and delivery time. They only oer a "best-eort." You can think
of CoS as "coarsely-grained" trac control and QoS as "nely-grained" trac
control.
• Though CoS is simple to manage, it lacks scalability and does not oer end-toend guarantees since it is based on L2 protocol.
52D-Link DCS-7517 User Manual
Conguration
QoS/DSCP
DSCP-ECN denes QoS at Layer 3 (Network Layer). The Dierentiated Services
(DiServ) model is based on packet marking and router queuing disciplines. The
marking is done by adding a eld to the IP header, called the DSCP (Dierentiated
Services Code Point). This is a 6-bit eld that provides 64 dierent class IDs. It gives
an indication of how a given packet is to be forwarded, known as the Per Hop
Behavior (PHB). The PHB describes a particular service level in terms of bandwidth,
queuing theory, and dropping (discarding the packet) decisions. Routers at each
network node classify packets according to their DSCP value and give them a
particular forwarding treatment. For example, how much bandwidth should be
reserved.
Please follow the steps below to enable QoS/DSCP:
1. Click Enable QoS/DSCP.
2. Choose the priority for each application. Lower values will provide higher priority,
starting with 1.
53D-Link DCS-7517 User Manual
Conguration
Event Management
Motion Detection
Motion can be detected by measuring change in speed or vector of an object or
objects in the eld of view.
Enable Motion Detection: Select this option to turn on the motion detection
feature.
Window Name: Create a name for the selected motion window. It will appear at the
top of the motion window.
Sensitivity: Set how sensitive motion detection will be from 0% to 100%. A low
sensitivity means that there must be large changes between two images in order
to detect motion, and a high sensitivity means that even small changes will cause
motion to be detected.
Low sensitivities may be useful when monitoring an area that has ickering lights or
a window to the outside in view. High sensitivities may be useful when monitoring
an area that rarely changes, such as a storeroom or warehouse.
Percentage: Set how much of the area being monitored for motion must change
for motion to be detected. A low percentage means that only part of the area being
monitored has to change to detect motion, and a high percentage means that most
of the area needs to change to detect motion.
Low percentages can be useful when monitoring an area such as a large room, and
high percentages can be useful when you are only monitoring a specic part of the
camera's view, such as a doorway.
Note: Setting a higher sensitivity and a lower percentage will make motion easier to
be detected.
54D-Link DCS-7517 User Manual
Conguration
New: Click to add a new window to specify an area of the video to monitor for
motion. A maximum of three motion windows can be opened simultaneously. Use
your mouse to drag the window frame to resize or the title bar to move. Clicking on
the ‘x’ at the upper right corner of the window will close the window.
Prole: You can congure three sets of sensor settings: Day, Night, and Schedule.
Save: Save the congured settings.
To enable motion detection, follow the steps below:
1. Click New to add a new motion detection window.
2. Enter a name in the Window Name eld.
3. Set the Sensitivity and Percentage settings to adjust how the camera will
detect motion.
4. Click Save to apply the changes.
5. Select Enable motion detection to activate motion detection.
55D-Link DCS-7517 User Manual
Conguration
Tamper Detection
With tamper detection, the camera is capable of detecting incidents such as when
the camera is redirected, blocked, de-focused, or even spray painted.
To enable tamper detection, follow the steps given below:
1. Select Enable camera tampering detection.
2. Enter the tamper trigger duration (10 sec. ~ 10 min.). The tamper alarm will be
triggered only when the tampering factor (the dierence between the current
frame and pre-saved background) exceeds the trigger threshold.
You can congure what the camera will do when tampering is detected on the
Event Settings page and selecting Camera Tampering Detection as the source in
Event Settings > Event Settings. Please refer to "Event Settings" on page 58 for
more detailed information.
56D-Link DCS-7517 User Manual
Conguration
DI and DO
This camera has a general I/O terminal block with one digital input and digital
output for device control. The I/O connector provides the physical interface for
digital input (DI+, GND) and digital output (DO+, GND) that is used for connecting a
variety of external alarm devices to the camera such as IR-Sensors and alarm relays.
You can congure what the camera will do when a DI signal is detected, or you can
congure when the camera will send a DO signal on the Event Settings page. Please
refer to "Event Settings" on page 58 for more detailed information.
57D-Link DCS-7517 User Manual
Conguration
Event Settings
This section explains how to congure the camera to respond to particular
situations (event). One example is conguring the camera to send images to an FTP
server or e-mail address when motion is detected.
Server Settings
Click Add on Event Settings page to open the Server Setting page. On this page,
you can congure up to ve servers to save snapshots, video, or system logs to.
Server name: Enter a name for the server.
• Server Type: There are four choices of server types available: E-mail, FTP, HTTP,
and Network storage. Select an item to display detailed conguration options.
You can congure either one or all of them.
E-mail: Select this to send the media les via e-mail when a trigger is activated.
• Sender e-mail address: Enter the e-mail address of the sender.
• Recipient e-mail address: Enter the e-mail address of the recipient.
• Server address: Enter the domain name or IP address of the e-mail server.
• User name: Enter the user name of the e-mail account if necessary.
• Password: Enter the password of the e-mail account if necessary.
• Server port: The default mail server port is set to 25. You can also manually set
another port.
6517
If your SMTP server requires a secure connection (SSL), select This server requires a
secure connection (SSL).
To verify if the e-mail settings are correctly congured, click Test. The result will be
shown in a pop-up window. If successful, you will also receive an e-mail indicating
the result.
Click Save to enable the settings, then click Close to exit the page.
58D-Link DCS-7517 User Manual
Conguration
FTP: Select this to send the media les to an FTP server when a trigger is activated.
• Server address: Enter the domain name or IP address of the FTP server.
• Server port: By default, the FTP server port is set to 21. It can also be assigned to
another port number between 1025 and 65535.
• User name: Enter the login name of the FTP account.
• Password: Enter the password of the FTP account.
• FTP folder name: Enter the folder where the media le will be placed. If the
folder name does not exist, the camera will create one on the FTP server.
• Passive mode: Most rewalls do not accept new connections initiated from
external requests. If the FTP server supports passive mode, select this option
to enable passive mode FTP and allow data transmission to pass through the
rewall.
To verify if the FTP settings are correctly congured, click Test. The result will be
shown in a pop-up window as shown. If successful, you will also receive a test.txt
le on the FTP server.
Click Save to enable the settings, then click Close to exit the page.
6517
HTTP: Select this to send the media les to an HTTP server when a trigger is
activated.
• URL: Enter the URL of the HTTP server.
• User name: Enter the user name if necessary.
• Password: Enter the password if necessary.
To verify if the HTTP settings are correctly congured, click Test. The result will be
shown in a pop-up window as below. If successful, you will receive a test.txt le on
the HTTP server. Click Save to enable the settings then click Close to exit the page.
Network storage: Select this to send the media les to a network storage location
when a trigger is activated. Click Save to enable the setting, then click Close to exit
the page. When completed, the new server settings will automatically be displayed
on the Event Settings page.
59D-Link DCS-7517 User Manual
Conguration
Media Settings
Click Add to open the Media Settings page. On this page, you can specify up to ve
types of media that can be sent when a trigger is activated.
Media name: Enter a name for the media setting.
Media Type: There are three media types available: Snapshot, Video Clip, and
System log. Select an item to display detailed conguration options. You can
congure either one or all of them.
Snapshot: Select this to send snapshots when a trigger is activated.
Source: Select this to take snapshots from stream 1 ~ 3.
Send pre-event images: Set the number of pre-event images to take. Pre-event
images are images taken before the trigger is activated. You can set up to seven
pre-event images to be taken.
Send post-event images: Set the number of post-event images to take. Post-event
images are images taken after a trigger is activated. You can set up to seven postevent images to be taken.
6517
File name prex: Enter the text that will be appended to the beginning of the le
name.
Add date and time sux to the le name: Select this option to add a date/time
sux to the le name.
Click Save to enable the settings, then click Close to exit the page.
60D-Link DCS-7517 User Manual
Conguration
Video clip: Select this to send video clips when a trigger is activated.
Source: Select a source for the video clip.
Pre-event recording: This sets how many seconds to record before the trigger is
activated. You can record up to nine seconds of pre-event video.
Maximum duration: This sets how many seconds of video to record in total, and
can be set up to 20 seconds. For example, if pre-event recording is set to 5 seconds
and the maximum duration is set to 10 seconds, the camera will continue to record
for another 5 seconds after the trigger is activated.
Maximum le size: Specify the maximum le size allowed.
File name prex: Enter the text that will be appended to the beginning of the le
name.
Click Save to enable the settings, then click Close to exit the page.
System log: Select this to send a system log when a trigger is activated. Click Save
to enable the settings, then click Close to exit the page.
When you are done, click Save to enable the settings and click Close to exit this
page. The new media settings will appear on the Event Settings page.
6517
61D-Link DCS-7517 User Manual
Conguration
Event Settings
In the Event Settings column, click Add to open the Event Settings page. On this
page, you can congure an event by setting a Trigger, Schedule, and Action. A total
of 3 events can be congured.
Event name: Enter a name for the event.
Enable this event: Select this to activate this event.
Priority: Set the priority for this event (High, Normal, or Low). Events with higher
priority will be executed rst.
Detect next event after * seconds: Select the delay time before allowing another
event to be triggered. This is used for both motion detection events and digital
input events.
Trigger
Here, you can dene what will trigger the event. There are several methods to
trigger an event, as shown below. Select an item to display detailed conguration
options.
6517
Video motion detection: This option makes use of the built-in motion detection
mechanism as a trigger source. To enable this function, you need to congure
a Motion Detection Window rst. For more information, please refer to "Motion
Detection" on page 54 for details.
Periodically: This option allows the camera to trigger periodically according to the
duration you set. You can set the duration up to 999 minutes.
Digital input: This option allows the camera to use an external digital input device
or sensor as a trigger source. Depending on your application, there are many
choices of digital input devices on the market, such as devices that detect changes
in temperature, vibration, sound, light, etc.
62D-Link DCS-7517 User Manual
Conguration
System boot: This option triggers the camera when the camera boots up, such as
when power is restored to the camera after a power outage.
Recording notify: This option allows the camera to trigger an event when the
recording disk is full or when recording starts to rewrite older data.
Camera tampering detection: This option allows the camera to trigger an event
when the camera detects that it is being tampered with. To enable this function,
you need to congure the Tamper detection option rst. Please refer to "Tamper
Detection" on page 56 for more detailed information.
Event Schedule
Here, you can specify the period of time when the event can be run.
1. Select the day(s) of the week.
2. Select the recording schedule in 24-hr time format.
Action
Here, you can dene the actions to be performed by the camera when the event
trigger is activated.
6517
Trigger digital output for X seconds: Enter the number of seconds to trigger the
digital output for when an event happens.
To record video or snapshots for your action, you will need to add a server and
media type rst.
• Add Server: Refer to Server Settings for more information.
• Add Media: Refer to Media Settings for more information.
• SD: Select the microSD card as the location for les to be sent to. Click SD Test
to verify that the microSD card is working properly. Click View to open the
microSD card to view les.
• Email: From the drop down menu, select the e-mail address to send
notications to.
63D-Link DCS-7517 User Manual
Conguration
Recording
Recording Settings
Click Add to open the recording settings page. On this page, you can dene
when and how the camera will record video based on a schedule or when it
is disconnected from the network. A total of two recording settings can be
congured.
Recording name: Enter a name for the recording setting.
Enable this recording: Select this option to enable the recording you are
specifying.
Priority: Select the relative importance of this recording setting (High, Normal, and
Low).
Source: Select the recording source (stream 1 ~ 3).
Trigger: Select a trigger source.
Schedule: Selecting this will record video according to the schedule you specify.
Network Fail: Selecting this will record video when a network failure is detected.
Recording Schedule: Specify period of time this recording will be active.
1. Select the days of the week.
2. Select the recording start and end times in 24-hr time format.
64D-Link DCS-7517 User Manual
Conguration
Destination: You can choose to record to network storage or a microSD card.
When you are done, select Enable this recording. Click Save to enable the setting
and click Close to exit this page. The new recording will appear in the drop-down
list on the recording page.
To remove a recording setting from the list, select a recording name from the dropdown list and click Delete.
65D-Link DCS-7517 User Manual
Conguration
Local Storage
Click on the dropdown icon to expand or collapse the menu items in this section.
SD Card Management
SD Card Status: This shows the status and reserved space of your microSD card.
Please remember to format the microSD card when using for the rst time.
Format: Click this icon to automatically format the microSD card
Enable Cyclic Storage: If you select this item, when the maximum capacity you
specify is reached, the oldest les will be overwritten by newer ones. The reserved
amount is reserved for cyclic recording to prevent malfunction. This value must be
larger than 15 Mbytes.
Enable Automatic Disk Cleanup: Check this item and enter the number of days
you wish to retain a le. For example, if you enter “7 days”, the recorded les will be
stored on the microSD card for 7 days.
Click Save to enable your settings.
Searching and Viewing the Records
File Attributes: Select one or more items as your search criteria.
Trigger Type: Select the type of trigger that was used to create the recording.
Media Type: Select the type of media that was used to save the recording.
Trigger Time: Manually enter the time range you want to search. Click Search
and the recorded data corresponding to the search criteria will be listed in Search
Results Window.
From/To: Enter the dates to search from and to.
66D-Link DCS-7517 User Manual
Conguration
Search Results
Show Entries: Select the number of search results to display at a time.
Search: Enter a keyword to search through the displayed results.
Download: Select a line from the search results and click this button to download
the le to your computer.
Uncheck All: Click this button to uncheck all of the displayed search results.
JPEGs to AVI: Select multiple JPEGs and click this button to convert them into a
single AVI video which can be saved to your local computer.
Remove: Select a search result and click this button to remove the le completely.
67D-Link DCS-7517 User Manual
Conguration
PTZ Control
Digital PTZ
You can save a total of 20 preset positions and select a set of preset positions for
the camera to patrol.
Please follow the steps below to save a position as a preset:
1. Adjust the camera view to your desired position using the buttons on the right
side of the window.
2. Enter a name for the preset position, which can be up to 40 characters long.
Click Add to enable the Setting. The new preset position will be displayed in the
Preset Location list on the left-hand side.
3. To add additional preset positions, please repeat steps 1~2.
4. To remove a preset position from the list, select it from the drop-down list and
click Delete.
5. Click Save to enable the setting. Your preset positions will also be displayed on
the Live Video page. Select one from the drop-down list and the camera will
move to the selected preset position.
Patrol Settings
You can select a sequence of preset positions for the camera to patrol. Please follow
the steps below to set up a patrol schedule:
1. Click a preset location on the list and click Select.
2. The selected preset position will be displayed in the Source list.
3. Set the Dwelling time for the preset position during auto patrol; this determines
how long the camera will stay at that preset position. Enter a value and click
Update.
4. Repeat step 1 and 3 to add additional preset position to the patrol list.
5. If you want to remove a preset position from the patrol list, select it from the
Source list and click Remove.
6. Select a position and click Up or Down to rearrange the patrol order.
7. Click Save to enable the setting.
68D-Link DCS-7517 User Manual
Conguration
Lens Control
The settings on this page allow you to remotely ne tune the zoom and focus to
achieve optimal performance.
Lens Zoom Speed: You can adjust the speed of the zoom by selecting a number
from the drop-down menu. Selecting a higher number will result in a faster zoom.
Use this slider control to ne tune the camera zoom.
Use this slider control to ne tune the camera focus.
Auto Focus: Allow the camera to adjust the focus automatically.
69D-Link DCS-7517 User Manual
Conguration
System
User Settings
This section explains how to enable password protection and create multiple
accounts.
Admin Password Setup:
The administrator account name is “admin”, which is permanent and cannot be
changed. The default password is blank. You can change the password by typing it
into the Password and Conrm password boxes and clicking Save.
Add User Account
This section lets you add a new user account and set privileges for it.
Username: Enter a username for the new account.
Password: Enter a password for the new account.
Privilege: Select the access rights for the new user.
Manage User
This section lets you change the password and privileges for existing users.
To make changes to a user account, select it from the User name dropdown box,
make your changes, then click Modify.
To delete a user account, select it form the User name dropdown box, then click
Delete.
70D-Link DCS-7517 User Manual
Conguration
Device Settings
Turn o the LED indicator: Select this option to turn o the LED next to the
lens. This allows the camera to be less conspicuous and more discreet.
Camera Name: Enter a name for your camera to help you identify it.
71D-Link DCS-7517 User Manual
Conguration
Time and Date
This section allows you to automatically or manually congure, update, and
maintain the internal system clock for your camera.
Current Server Time: Displays the camera's current time.
Time Zone: Select your time zone from the drop-down menu.
Enable Daylight Saving: Select this to enable the daylight saving time (DST).
During DST, the system clock moves one hour ahead. To utilize this feature, be sure
to rst set the time zone of your network camera, then set the starting and ending
time to use DST.
Automatic Time Conguration: Enable this feature to set the camera's clock
automatically from an NTP server.
NTP Server: Network Time Protocol (NTP) synchronizes the network camera with an
Internet time server. Choose the one that is closest to your location.
Update Interval: This sets the time interval for updating the time information from
NTP server.
Set the date and time manually: This option allows you to set the time and date
manually.
Copy Your Computer’s Time Setting: This will set the camera's clock to match the
time from your PC.
72D-Link DCS-7517 User Manual
Conguration
Maintenance
This page lets you reboot the camera, restore the camera to the factory default
settings, save and restore the camera's conguration, and upgrade the rmware.
Schedule Reboot: This feature allows the camera to perform a scheduled reboot.
Select the days and time you want the camera to reboot, then click Save. Make
sure you have set the camera's clock to the correct date and time before using this
feature.
Reboot: Click Reboot to reboot the camera, which will take about one minute to
complete. When completed, the live video page will be displayed in your browser. A
message will be displayed during the reboot process.
If the connection fails after rebooting, manually enter the IP address of the camera
in the address eld to resume your connection.
Restore to Default: Click Default to restore the camera to the factory default
settings.
Export setting backup le: Click Export to export your camera settings to a le you
can save on your computer.
Upload setting backup le: Click Browse… to select a camera settings le to
upload to the camera. Please make sure that the model and rmware version
of your le is same as your camera. If you have set up a xed IP or other special
settings for your device, uploading a camera settings le is not recommended.
Firmware Upgrade: Click Browse... to select a rmware le to upload to the
camera. Please make sure that the model of the rmware is the same as your
camera. This process will take a few minutes to complete, and will reboot the
camera automatically.
Note: Do not power o the camera during the upgrade
You can nd the latest rmware for your camera on the D-Link website.
73D-Link DCS-7517 User Manual
Conguration
Parameter List
The Parameters List page lists all of the camera's parameters in alphabetical order. If
you need technical assistance, please provide the information listed on this page.
74D-Link DCS-7517 User Manual
Conguration
Logs
This column displays the system log in chronological order. The system log is stored
in the camera’s buer and will be overwritten when reaching a certain limit.
75D-Link DCS-7517 User Manual
Appendix A - Technical Specications
Appendix A - Technical Specications
Technical Specications
Camera
Camera Hardware Profile • 1/3.2” 5 Megapixel CMOS sensor
• 30 meter IR illumination distance
• Built-in Infrared-Cut Removable (ICR) Filter module
• Minimum illumination:
• 0.5 lux Color mode
• 0.1 lux Black and White mode
• 0 lux Black and White mode with IR LED on
• Minimum object distance 0.3 m
Camera Housing • IP66 compliant weatherproof housing • Included sunshield
Image Features • Configurable image size, quality, frame rate, and bit rate
• Time stamp and text overlays
• 3 configurable motion detection windows
• Tamper detection
Video Compression • Simultaneous H.264/MJPEG format compression
• H.264 multicast streaming
Video Resolution • 16:9 1920x1080, 1280x720, 960 x 540 at up to 30 fps • 4:3 - 2560x1920, 2048x1536, 1600x1200, 1280x960 at up to 15 fps
Audio Support • AAC • G.711
External Device Interfaces • 10/100 BASE-TX Ethernet port with PoE
• 1 DI / 1 DO
• Reset button
• 2.8 to 12 mm motorized zoom varifocal DC iris lens
• Aperture F1.8
• Angle of view
• (H) 29.47° to 72.84°
• (V) 21.72° to 54.69°
• Shutter Speed: 1/2.5 to 1/10,000
• 4x digital zoom
• Configurable privacy mask zones
• Configurable exposure, brightness, saturation, contrast, sharpness, white balance,
WDR, flip and mirror
• JPEG for still images
• Video Out (BNC)
• microSD card Slot
• Audio input / output
1
Network
Network Protocols • IPv6
• IPv4
• TCP/IP
• UDP
• ICMP
• DHCP client
• NTP client (D-Link)
• DNS client
• DDNS client (D-Link)
• SMTP client
• FTP client
Security • Administrator and user group protection
• Remote client access control
• HTTP / HTTPS
• Samba client
• PPPoE
• UPnP port forwarding
• RTP / RTSP/ RTCP
• IP filtering
• QoS
• CoS
• Multicast
• ONVIF compliant
• SNMP
• HTTP and RTSP authentication
• HTTPS encryption for web access
76D-Link DCS-7517 User Manual
Appendix A - Technical Specications
System Management
System Requirements for Web Interface • Browser: Internet Explorer 7 or higher, Firefox 19 or higher
Event Management • Motion detection
• Event notification and uploading of snapshots/video clips via e-mail or FTP
Remote Management • Take snapshots/video clips and save to local hard drive • Configuration interface accessible via web browser
OS Support (for setup utility) • Operating System: Windows 10/8/7/Vista/XP/2000
D-ViewCam™ System Requirements • Operating System: Windows 10/8/7/Vista/XP/2000
• Web Browser: Internet Explorer 7 or higher
D-ViewCam™ Software Functions • Remote management/control of up to 32 cameras
• Supports all management functions provided in web interface
• Supports multiple HTTP, SMTP, and FTP servers
• Multiple event notifications
• Multiple recording methods for easy backup
• Protocol: Standard TCP/IP
• Viewing of up to 32 cameras on one screen
• Scheduled motion triggered, or manual recording options
General
Weight • 1.25 kg (2.75 lbs) for camera only, without sunshield and mounting bracket
Power • External power adapter: 12 V DC 1.5 A. 50/60 Hz • PoE: IEEE 802.3af Class 0
Power Consumption • Max:12.48 W
Temperature • Operating: -40 to 50 ˚C (-40 to 122 ˚F) • Storage: -20 to 70 ˚C (-4 to 158 ˚F)
Humidity • Operating: 20% to 80% non-condensing • Storage: 5% to 95% non-condensing
Certifications • CE
• CE LVD
• ICES-003
• FCC
• C-Tick
Dimensions
1
SD/SDHC/SDXC v3.01 compatible
Ø110
290.34
Ø83
135.59
77D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
Appendix B - Regulatory Information
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Non-modication Statement
Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Innovation, Science and Economic Development Canada (ISED) Statement:
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
CE EMI Class A Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
78D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
SAFETY INSTRUCTIONS
The following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage.
Remember to consult the product user instructions for more details.
• Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal)
before touching the product.
• Do not attempt to service the product and never disassemble the product. For some products with a user replaceable battery, please read
and follow the instructions in the user manual.
• Do not spill food or liquid on your product and never push any objects into the openings of your product.
• Do not use this product near water, areas with high humidity, or condensation unless the product is specically rated for outdoor application.
• Keep the product away from radiators and other heat sources.
• Always unplug the product from mains power before cleaning and use a dry lint free cloth only.
SICHERHEITSVORSCHRIFTEN
Die folgenden allgemeinen Sicherheitsvorschriften dienen als Hilfe zur Gewährleistung Ihrer eigenen Sicherheit und zum Schutz Ihres Produkts.
Weitere Details nden Sie in den Benutzeranleitungen zum Produkt.
• Statische Elektrizität kann elektronischen Komponenten schaden. Um Schäden durch statische Auadung zu vermeiden, leiten Sie
elektrostatische Ladungen von Ihrem Körper ab,
(z. B. durch Berühren eines geerdeten blanken Metallteils), bevor Sie das Produkt berühren.
• Unterlassen Sie jeden Versuch, das Produkt zu warten, und versuchen Sie nicht, es in seine Bestandteile zu zerlegen. Für einige Produkte mit
austauschbaren Akkus lesen Sie bitte das Benutzerhandbuch und befolgen Sie die dort beschriebenen Anleitungen.
• Vermeiden Sie, dass Speisen oder Flüssigkeiten auf Ihr Produkt gelangen, und stecken Sie keine Gegenstände in die Gehäuseschlitze oder
-önungen Ihres Produkts.
• Verwenden Sie dieses Produkt nicht in unmittelbarer Nähe von Wasser und nicht in Bereichen mit hoher Luftfeuchtigkeit oder Kondensation,
es sei denn, es ist speziell zur Nutzung in Außenbereichen vorgesehen und eingestuft.
• Halten Sie das Produkt von Heizkörpern und anderen Quellen fern, die Wärme erzeugen.
• Trennen Sie das Produkt immer von der Stromzufuhr, bevor Sie es reinigen und verwenden Sie dazu ausschließlich ein trockenes fusselfreies
Tuch.
79D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
CONSIGNES DE SÉCURITÉ
Les consignes générales de sécurité ci-après sont fournies an d’assurer votre sécurité personnelle et de protéger le produit d’éventuels
dommages. Veuillez consulter les consignes d’utilisation du produit pour plus de détails.
• L’électricité statique peut endommager les composants électroniques. Déchargez l’électricité statique de votre corps (en touchant un objet
en métal relié à la terre par exemple) avant de toucher le produit.
• N’essayez pas d’intervenir sur le produit et ne le démontez jamais. Pour certains produits contenant une batterie remplaçable par l’utilisateur,
veuillez lire et suivre les consignes contenues dans le manuel d’utilisation.
• Ne renversez pas d’aliments ou de liquide sur le produit et n’insérez jamais d’objets dans les orices.
• N’utilisez pas ce produit à proximité d’un point d’eau, de zones très humides ou de condensation sauf si le produit a été spéciquement
conçu pour une application extérieure.
• Éloignez le produit des radiateurs et autres sources de chaleur.
• Débranchez toujours le produit de l’alimentation avant de le nettoyer et utilisez uniquement un chion sec non pelucheux.
INSTRUCCIONES DE SEGURIDAD
Las siguientes directrices de seguridad general se facilitan para ayudarle a garantizar su propia seguridad personal y para proteger el producto
frente a posibles daños. No olvide consultar las instrucciones del usuario del producto para obtener más información.
• La electricidad estática puede resultar nociva para los componentes electrónicos. Descargue la electricidad estática de su cuerpo (p. ej.,
tocando algún metal sin revestimiento conectado a tierra) antes de tocar el producto.
• No intente realizar el mantenimiento del producto ni lo desmonte nunca. Para algunos productos con batería reemplazable por el usuario,
lea y siga las instrucciones del manual de usuario.
• No derrame comida o líquidos sobre el producto y nunca deje que caigan objetos en las aberturas del mismo.
• No utilice este producto cerca del agua, en zonas con humedad o condensación elevadas a menos que el producto esté clasicado
especícamente para aplicación en exteriores.
• Mantenga el producto alejado de los radiadores y de otras fuentes de calor.
• Desenchufe siempre el producto de la alimentación de red antes de limpiarlo y utilice solo un paño seco sin pelusa.
80D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
ISTRUZIONI PER LA SICUREZZA
Le seguenti linee guida sulla sicurezza sono fornite per contribuire a garantire la sicurezza personale degli utenti e a proteggere il prodotto da
potenziali danni. Per maggiori dettagli, consultare le istruzioni per l’utente del prodotto.
• L’elettricità statica può essere pericolosa per i componenti elettronici. Scaricare l’elettricità statica dal corpo (ad esempio toccando una parte
metallica collegata a terra) prima di toccare il prodotto.
• Non cercare di riparare il prodotto e non smontarlo mai. Per alcuni prodotti dotati di batteria sostituibile dall’utente, leggere e seguire le
istruzioni riportate nel manuale dell’utente.
• Non versare cibi o liquidi sul prodotto e non spingere mai alcun oggetto nelle aperture del prodotto.
• Non usare questo prodotto vicino all’acqua, in aree con elevato grado di umidità o soggette a condensa a meno che il prodotto non sia
specicatamente approvato per uso in ambienti esterni.
• Tenere il prodotto lontano da caloriferi e altre fonti di calore.
• Scollegare sempre il prodotto dalla presa elettrica prima di pulirlo e usare solo un panno asciutto che non lasci lacce.
VEILIGHEIDSINFORMATIE
De volgende algemene veiligheidsinformatie werd verstrekt om uw eigen persoonlijke veiligheid te waarborgen en uw product te beschermen
tegen mogelijke schade. Denk eraan om de gebruikersinstructies van het product te raadplegen voor meer informatie.
• Statische elektriciteit kan schadelijk zijn voor elektronische componenten. Ontlaad de statische elektriciteit van uw lichaam (d.w.z. het
aanraken van geaard bloot metaal) voordat uhet product aanraakt.
• U mag nooit proberen het product te onderhouden en u mag het product nooit demonteren. Voor sommige producten met door de
gebruiker te vervangen batterij, dient u de instructies in de gebruikershandleiding te lezen en te volgen.
• Mors geen voedsel of vloeistof op uw product en u mag nooit voorwerpen in de openingen van uw product duwen.
• Gebruik dit product niet in de buurt van water, gebieden met hoge vochtigheid of condensatie, tenzij het product speciek geclassiceerd is
voor gebruik buitenshuis.
• Houd het product uit de buurt van radiators en andere warmtebronnen.
• U dient het product steeds los te koppelen van de stroom voordat u het reinigt en gebruik uitsluitend een droge pluisvrije doek.
81D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
Disposing and Recycling Your Product
ENGLISH EN
This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed
of in household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has
reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help to
conserve the environment and protect human health.
D-Link and the Environment
At D-Link, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimise
this impact D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both
products and packaging.
D-Link recommends that you always switch o or unplug your D-Link products when they are not in use. By doing so you will help to save energy
and reduce CO2 emissions.
To learn more about our environmentally responsible products and packaging please visit www.dlinkgreen.com.
DEUTSCH DE
Dieses Symbol auf dem Produkt oder der Verpackung weist darauf hin, dass dieses Produkt gemäß bestehender örtlicher Gesetze
und Vorschriften nicht über den normalen Hausmüll entsorgt werden sollte, sondern einer Wiederverwertung zuzuführen ist. Bringen
Sie es bitte zu einer von Ihrer Kommunalbehörde entsprechend amtlich ausgewiesenen Sammelstelle, sobald das Produkt das Ende
seiner Nutzungsdauer erreicht hat. Für die Annahme solcher Produkte erheben einige dieser Stellen keine Gebühren. Durch ein auf
diese Weise durchgeführtes Recycling des Produkts und seiner Verpackung helfen Sie, die Umwelt zu schonen und die menschliche
Gesundheit zu schützen.
D-Link und die Umwelt
D-Link ist sich den möglichen Auswirkungen seiner Geschäftstätigkeiten und seiner Produkte auf die Umwelt bewusst und fühlt sich verpichtet,
diese entsprechend zu mindern. Zu diesem Zweck entwickelt und stellt D-Link seine Produkte mit dem Ziel größtmöglicher Umweltfreundlichkeit
her und verwendet wiederverwertbare, schadstoarme Materialien bei Produktherstellung und Verpackung.
D-Link empehlt, Ihre Produkte von D-Link, wenn nicht in Gebrauch, immer auszuschalten oder vom Netz zu nehmen. Auf diese Weise helfen
Sie, Energie zu sparen und CO2-Emissionen zu reduzieren.
Wenn Sie mehr über unsere umweltgerechten Produkte und Verpackungen wissen möchten, nden Sie entsprechende Informationen im Internet
unter www.dlinkgreen.com.
82D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
FRANÇAIS FR
Ce symbole apposé sur le produit ou son emballage signie que, conformément aux lois et règlementations locales, ce produit ne
doit pas être éliminé avec les déchets domestiques mais recyclé. Veuillez le rapporter à un point de collecte prévu à cet eet par les
autorités locales; certains accepteront vos produits gratuitement. En recyclant le produit et son emballage de cette manière, vous
aidez à préserver l’environnement et à protéger la santé de l’homme.
D-Link et l’environnement
Chez D-Link, nous sommes conscients de l'impact de nos opérations et produits sur l'environnement et nous engageons à le réduire. Pour limiter
cet impact, D-Link conçoit et fabrique ses produits de manière aussi écologique que possible, en utilisant des matériaux recyclables et faiblement
toxiques, tant dans ses produits que ses emballages.
D-Link recommande de toujours éteindre ou débrancher vos produits D-Link lorsque vous ne les utilisez pas. Vous réaliserez ainsi des économies
d’énergie et réduirez vos émissions de CO2.
Pour en savoir plus sur les produits et emballages respectueux de l’environnement, veuillez consulter le www.dlinkgreen.com.
ESPAÑOL ES
Este símbolo en el producto o el embalaje signica que, de acuerdo con la legislación y la normativa local, este producto no se debe
desechar en la basura doméstica sino que se debe reciclar. Llévelo a un punto de recogida designado por las autoridades locales una
vez que ha llegado al n de su vida útil; algunos de ellos aceptan recogerlos de forma gratuita. Al reciclar el producto y su embalaje
de esta forma, contribuye a preservar el medio ambiente y a proteger la salud de los seres humanos.
D-Link y el medio ambiente
En D-Link, comprendemos y estamos comprometidos con la reducción del impacto que puedan tener nuestras actividades y nuestros productos
en el medio ambiente. Para reducir este impacto, D-Link diseña y fabrica sus productos para que sean lo más ecológicos posible, utilizando
materiales reciclables y de baja toxicidad tanto en los productos como en el embalaje.
D-Link recomienda apagar o desenchufar los productos D-Link cuando no se estén utilizando. Al hacerlo, contribuirá a ahorrar energía y a reducir
las emisiones de CO2.
Para obtener más información acerca de nuestros productos y embalajes ecológicos, visite el sitio www.dlinkgreen.com.
83D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
ITALIANO IT
La presenza di questo simbolo sul prodotto o sulla confezione del prodotto indica che, in conformità alle leggi e alle normative locali,
questo prodotto non deve essere smaltito nei riuti domestici, ma avviato al riciclo. Una volta terminato il ciclo di vita utile, portare il
prodotto presso un punto di raccolta indicato dalle autorità locali. Alcuni questi punti di raccolta accettano gratuitamente i prodotti
da riciclare. Scegliendo di riciclare il prodotto e il relativo imballaggio, si contribuirà a preservare l'ambiente e a salvaguardare la
salute umana.
D-Link e l'ambiente
D-Link cerca da sempre di ridurre l'impatto ambientale dei propri stabilimenti e dei propri prodotti. Allo scopo di ridurre al minimo tale impatto,
D-Link progetta e realizza i propri prodotti in modo che rispettino il più possibile l'ambiente, utilizzando materiali riciclabili a basso tasso di
tossicità sia per i prodotti che per gli imballaggi.
D-Link raccomanda di spegnere sempre i prodotti D-Link o di scollegarne la spina quando non vengono utilizzati. In questo modo si contribuirà
a risparmiare energia e a ridurre le emissioni di anidride carbonica.
Per ulteriori informazioni sui prodotti e sugli imballaggi D-Link a ridotto impatto ambientale, visitate il sito all'indirizzo www.dlinkgreen.com.
NEDERLANDS NL
Dit symbool op het product of de verpakking betekent dat dit product volgens de plaatselijke wetgeving niet mag worden weggegooid
met het huishoudelijk afval, maar voor recyclage moeten worden ingeleverd. Zodra het product het einde van de levensduur heeft
bereikt, dient u het naar een inzamelpunt te brengen dat hiertoe werd aangeduid door uw plaatselijke autoriteiten, sommige
autoriteiten accepteren producten zonder dat u hiervoor dient te betalen. Door het product en de verpakking op deze manier te
recyclen helpt u het milieu en de gezondheid van de mens te beschermen.
D-Link en het milieu
Bij D-Link spannen we ons in om de impact van onze handelingen en producten op het milieu te beperken. Om deze impact te beperken, ontwerpt
en bouwt D-Link zijn producten zo milieuvriendelijk mogelijk, door het gebruik van recycleerbare producten met lage toxiciteit in product en
verpakking.
D-Link raadt aan om steeds uw D-Link producten uit te schakelen of uit de stekker te halen wanneer u ze niet gebruikt. Door dit te doen bespaart
u energie en beperkt u de CO2-emissies.
Breng een bezoek aan www.dlinkgreen.com voor meer informatie over onze milieuverantwoorde producten en verpakkingen.
84D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
POLSKI PL
Ten symbol umieszczony na produkcie lub opakowaniu oznacza, że zgodnie z miejscowym prawem i lokalnymi przepisami
niniejszego produktu nie wolno wyrzucać jak odpady czy śmieci z gospodarstwa domowego, lecz należy go poddać procesowi
recyklingu. Po zakończeniu użytkowania produktu, niektóre odpowiednie do tego celu podmioty przyjmą takie produkty
nieodpłatnie, dlatego prosimy dostarczyć go do punktu zbiórki wskazanego przez lokalne władze. Poprzez proces recyklingu i
dzięki takiemu postępowaniu z produktem oraz jego opakowaniem, pomogą Państwo chronić środowisko naturalne i dbać o
ludzkie zdrowie.
D-Link i środowisko
D-Link podchodzimy w sposób świadomy do ochrony otoczenia oraz jesteśmy zaangażowani w zmniejszanie wpływu naszych działań i produktów
na środowisko naturalne. W celu zminimalizowania takiego wpływu rma D-Link konstruuje i wytwarza swoje produkty w taki sposób, aby były
one jak najbardziej przyjazne środowisku, stosując do tych celów materiały nadające się do powtórnego wykorzystania, charakteryzujące się
małą toksycznością zarówno w przypadku samych produktów jak i opakowań.
Firma D-Link zaleca, aby Państwo zawsze prawidłowo wyłączali z użytku swoje produkty D-Link, gdy nie są one wykorzystywane. Postępując w
ten sposób pozwalają Państwo oszczędzać energię i zmniejszać emisje CO2.
Aby dowiedzieć się więcej na temat produktów i opakowań mających wpływ na środowisko prosimy zapoznać się ze stroną Internetową www.
dlinkgreen.com.
ČESKY CZ
Tento symbol na výrobku nebo jeho obalu znamená, že podle místně platných předpisů se výrobek nesmí vyhazovat do komunálního
odpadu, ale odeslat k recyklaci. Až výrobek doslouží, odneste jej prosím na sběrné místo určené místními úřady k tomuto účelu.
Některá sběrná místa přijímají výrobky zdarma. Recyklací výrobku i obalu pomáháte chránit životní prostředí i lidské zdraví.
D-Link a životní prostředí
Ve společnosti D-Link jsme si vědomi vlivu našich provozů a výrobků na životní prostředí a snažíme se o minimalizaci těchto vlivů. Proto své
výrobky navrhujeme a vyrábíme tak, aby byly co nejekologičtější, a ve výrobcích i obalech používáme recyklovatelné a nízkotoxické materiály.
Společnost D-Link doporučuje, abyste své výrobky značky D-Link vypnuli nebo vytáhli ze zásuvky vždy, když je nepoužíváte. Pomůžete tak šetřit
energii a snížit emise CO2.
Více informací o našich ekologických výrobcích a obalech najdete na adrese www.dlinkgreen.com.
85D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
MAGYAR HU
Ez a szimbólum a terméken vagy a csomagoláson azt jelenti, hogy a helyi törvényeknek és szabályoknak megfelelően ez a termék
nem semmisíthető meg a háztartási hulladékkal együtt, hanem újrahasznosításra kell küldeni. Kérjük, hogy a termék élettartamának
elteltét követően vigye azt a helyi hatóság által kijelölt gyűjtőhelyre. A termékek egyes helyeken ingyen elhelyezhetők. A termék és
a csomagolás újrahasznosításával segíti védeni a környezetet és az emberek egészségét.
A D-Link és a környezet
A D-Linknél megértjük és elkötelezettek vagyunk a műveleteink és termékeink környezetre gyakorolt hatásainak csökkentésére. Az ezen hatás
csökkentése érdekében a D-Link a lehető leginkább környezetbarát termékeket tervez és gyárt azáltal, hogy újrahasznosítható, alacsony károsanyagtartalmú termékeket gyárt és csomagolásokat alkalmaz.
A D-Link azt javasolja, hogy mindig kapcsolja ki vagy húzza ki a D-Link termékeket a tápforrásból, ha nem használja azokat. Ezzel segít az energia
megtakarításában és a széndioxid kibocsátásának csökkentésében.
Környezetbarát termékeinkről és csomagolásainkról további információkat a www.dlinkgreen.com weboldalon tudhat meg.
NORSK NO
Dette symbolet på produktet eller forpakningen betyr at dette produktet ifølge lokale lover og forskrifter ikke skal kastes sammen
med husholdningsavfall, men leveres inn til gjenvinning. Vennligst ta det til et innsamlingssted anvist av lokale myndigheter når
det er kommet til slutten av levetiden. Noen steder aksepteres produkter uten avgift. Ved på denne måten å gjenvinne produktet
og forpakningen hjelper du å verne miljøet og beskytte folks helse.
D-Link og miljøet
Hos D-Link forstår vi oss på og er forpliktet til å minske innvirkningen som vår drift og våre produkter kan ha på miljøet. For å minimalisere denne
innvirkningen designer og lager D-Link produkter som er så miljøvennlig som mulig, ved å bruke resirkulerbare, lav-toksiske materialer både i
produktene og forpakningen.
D-Link anbefaler at du alltid slår av eller frakobler D-Link-produkter når de ikke er i bruk. Ved å gjøre dette hjelper du å spare energi og å redusere
CO2-utslipp.
For mer informasjon angående våre miljøansvarlige produkter og forpakninger kan du gå til www.dlinkgreen.com.
86D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
DANSK DK
Dette symbol på produktet eller emballagen betyder, at dette produkt i henhold til lokale love og regler ikke må bortskaes som
husholdningsaald, mens skal sendes til genbrug. Indlever produktet til et indsamlingssted som angivet af de lokale myndigheder,
når det er nået til slutningen af dets levetid. I nogle tilfælde vil produktet blive modtaget gratis. Ved at indlevere produktet og dets
emballage til genbrug på denne måde bidrager du til at beskytte miljøet og den menneskelige sundhed.
D-Link og miljøet
Hos D-Link forstår vi og bestræber os på at reducere enhver indvirkning, som vores aktiviteter og produkter kan have på miljøet. For at minimere
denne indvirkning designer og producerer D-Link sine produkter, så de er så miljøvenlige som muligt, ved at bruge genanvendelige materialer
med lavt giftighedsniveau i både produkter og emballage.
D-Link anbefaler, at du altid slukker eller frakobler dine D-Link-produkter, når de ikke er i brug. Ved at gøre det bidrager du til at spare energi og
reducere CO2-udledningerne.
Du kan nde ere oplysninger om vores miljømæssigt ansvarlige produkter og emballage på www.dlinkgreen.com.
SUOMI FI
Tämä symboli tuotteen pakkauksessa tarkoittaa, että paikallisten lakien ja säännösten mukaisesti tätä tuotetta ei pidä hävittää
yleisen kotitalousjätteen seassa vaan se tulee toimittaa kierrätettäväksi. Kun tuote on elinkaarensa päässä, toimita se lähimpään
viranomaisten hyväksymään kierrätyspisteeseen. Kierrättämällä käytetyn tuotteen ja sen pakkauksen autat tukemaan sekä ympäristön
että ihmisten terveyttä ja hyvinvointia.
D-Link ja ympäristö
D-Link ymmärtää ympäristönsuojelun tärkeyden ja on sitoutunut vähentämään tuotteistaan ja niiden valmistuksesta ympäristölle mahdollisesti
aiheutuvia haittavaikutuksia. Nämä negatiiviset vaikutukset minimoidakseen D-Link suunnittelee ja valmistaa tuotteensa mahdollisimman
ympäristöystävällisiksi käyttämällä kierrätettäviä, alhaisia pitoisuuksia haitallisia aineita sisältäviä materiaaleja sekä tuotteissaan että niiden
pakkauksissa.
Suosittelemme, että irrotat D-Link-tuotteesi virtalähteestä tai sammutat ne aina, kun ne eivät ole käytössä. Toimimalla näin autat säästämään
energiaa ja vähentämään hiilidioksiidipäästöjä.
Lue lisää ympäristöystävällisistä D-Link-tuotteista ja pakkauksistamme osoitteesta www.dlinkgreen.com.
87D-Link DCS-7517 User Manual
Appendix B - Regulatory Information
SVENSKA SE
Den här symbolen på produkten eller förpackningen betyder att produkten enligt lokala lagar och föreskrifter inte skall kastas i
hushållssoporna utan i stället återvinnas. Ta den vid slutet av dess livslängd till en av din lokala myndighet utsedd uppsamlingsplats,
vissa accepterar produkter utan kostnad. Genom att på detta sätt återvinna produkten och förpackningen hjälper du till att bevara
miljön och skydda människors hälsa.
D-Link och miljön
På D-Link förstår vi och är fast beslutna att minska den påverkan våra verksamheter och produkter kan ha på miljön. För att minska denna påverkan
utformar och bygger D-Link sina produkter för att de ska vara så miljövänliga som möjligt, genom att använda återvinningsbara material med
låg gifthalt i både produkter och förpackningar.
D-Link rekommenderar att du alltid stänger av eller kopplar ur dina D-Link produkter när du inte använder dem. Genom att göra detta hjälper
du till att spara energi och minska utsläpp av koldioxid.
För mer information om våra miljöansvariga produkter och förpackningar www.dlinkgreen.com.
PORTUGUÊS PT
Este símbolo no produto ou embalagem signica que, de acordo com as leis e regulamentações locais, este produto não deverá ser
eliminado juntamente com o lixo doméstico mas enviado para a reciclagem. Transporte-o para um ponto de recolha designado pelas
suas autoridades locais quando este tiver atingido o m da sua vida útil, alguns destes pontos aceitam produtos gratuitamente. Ao
reciclar o produto e respectiva embalagem desta forma, ajuda a preservar o ambiente e protege a saúde humana.
A D-Link e o ambiente
Na D-Link compreendemos e comprometemo-nos com a redução do impacto que as nossas operações e produtos possam ter no ambiente.
Para minimizar este impacto a D-Link concebe e constrói os seus produtos para que estes sejam o mais inofensivos para o ambiente possível,
utilizando meteriais recicláveis e não tóxicos tanto nos produtos como nas embalagens.
A D-Link recomenda que desligue os seus produtos D-Link quando estes não se encontrarem em utilização. Com esta acção ajudará a poupar
energia e reduzir as emissões de CO2.
Para saber mais sobre os nossos produtos e embalagens responsáveis a nível ambiental visite www.dlinkgreen.com.
88D-Link DCS-7517 User Manual
Loading...