D-Link DCS-2802KT-EU Service Manual
DCS-2802KT-EU
Wire-Free Camera Kit
User Manual
September 21, 2018
Hardware: A1
Manual Version: 1.00
Manual Overview
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes. Information in this document may become obsolete as our services and
websites develop and change. Please refer to the www.mydlink.com website for the most current information.
Manual Revisions
Revision Date Description
1.00 September 4, 2018 Initial release
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2018 by D-Link Corporation, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation, Inc.
iD-Link DCS-2802KT-EU User Manual
Table of Contents
Table of Contents
Product Overview ..............................................................1
Package Contents .........................................................................1
Introduction ................................................................................... 2
System Requirements ................................................................. 2
Hardware Overview .....................................................................3
Camera .....................................................................................3
Camera LED Behavior ..........................................................4
Hardware Overview .....................................................................5
Hub ............................................................................................ 5
Hub LED Behavior .................................................................6
Safety ................................................................................................ 7
Before you Begin ...........................................................................7
Wireless Installation Considerations ......................................8
Camera Placement Precautions .............................................. 9
Getting Started ................................................................ 10
Mounting the Camera .......................................................10
Controlling Your Hub .................................................................21
Device .....................................................................................22
Troubleshooting .............................................................. 24
Technical Specications .................................................. 25
Camera (DCS-2800LH-EU) .......................................................25
Technical Specications .................................................. 27
Hub (DCS-H100) ..........................................................................27
Regulatory Information ..................................................29
DCS-2800LH-EU ..........................................................................29
Regulatory Information ..................................................46
DCS-H100 ......................................................................................46
Snap Mount .....................................................................10
Mounting the Camera .......................................................12
Threaded Mount ............................................................12
Setting Up the Cameras With the mydlink™ App ..........14
Using the mydlink App ....................................................16
Controlling Your Cameras ........................................................ 16
Camera Options ..........................................................................17
Device .....................................................................................18
iiD-Link DCS-2802KT-EU User Manual
Section 1 - Product Overview
DCH-H100
Hub
2 x DCS-2800LH-EU
Cameras
DCH-H100 hub power
adapter
Product Overview
Package Contents
DCS-2800LH-EU micro-USB
camera power adapter
Quick Installation Guide
2 x Snap Mounts
Screws and plastic anchors
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a dierent voltage rating than the one included with your product will cause damage and void the warranty.
1D-Link DCS-2802KT-EU User Manual
Section 1 - Product Overview
Introduction
The mydlink™ Pro DCS-2802KT-EU is a bundle consisting of two DCS-2800LH-EU Wire-Free Cameras and a DCS-H100 Hub which are ideal for Small
Oce/Home Oce (SOHO) surveillance applications. The DCS-2800LH-EU is a compact, wireless network battery camera suitable for day-time and
night-time outdoor environments. It features built-in night vision, motion detection, and a free mobile app — so you can feel at ease when you’re
away from home.
System Requirements
Network Requirements
mydlink App Requirements
Optional Requirements
• Broadband Internet connection
• A router connected to your broadband modem
• iPhone, iPad, or Android smartphone or tablet (please refer to the
mobile app’s store page to check whether your device is compatible)
with Bluetooth 4.0 and above
• Email account (for mydlink service registration)
• A microSD memory card (required for recording to onboard storage
slot in the hub). SDHC class 6 or above is recommended
2D-Link DCS-2802KT-EU User Manual
Section 1 - Product Overview
Sync Button
1
Hardware Overview
Camera
Front Back
3
Built-in Microphone
4
1080p Lens
5
Light Sensor
6
Status LED
7
PIR Detector Window
8
Speaker
Micro-USB Port
2
1 Sync Button Press to start syncing the camera to the hub. Press to power on the camera from factory o state.
2 Speaker Speaker for the two-way audio feature.
3 Built-in Microphone Listens to the environment.
4 1080p Lens Records 1080p video.
5 Light Sensor Senses light to determine if night mode should be enabled.
6 Status LED See Camera LED Behavior on page 4.
7 PIR Detector Window The PIR motion detector is behind this window. Senses motion to trigger recordings.
8 Micro-USB Port
Peel back the water-resistant cover and plug the supplied power connector here to charge the camera's
battery. Note: Please only plug in the camera in a dry location.
3D-Link DCS-2802KT-EU User Manual
Section 1 - Product Overview
Camera LED Behavior
Status LED
Green
Red
Orange
Solid (for 10 sec.) Paired successfully.
Solid Battery is fully charged while power connector is still plugged in.
Blinking (every 1 sec.) Currently pairing. Maximum duration is 120 seconds.
Solid (for 10 sec.) Pairing failed, unpaired.
Blinking (every 30 sec.) Lost connection with the hub.
Blinking (every 1 sec.) Currently upgrading rmware.
Blinking (every 10 sec.) Currently charging battery.
Blinking (every 30 sec.) Low battery. Less than 15% remaining.
Blinks (1 time) PIR motion sensor triggered.
4D-Link DCS-2802KT-EU User Manual
Section 1 - Product Overview
Hardware Overview
Hub
Front
1
LED Panel
2
microSD Slot
Reset Button
LAN Port
3
4
Back
1 LED Panel See Hub LED Behavior on page 6.
2 microSD Slot microSD/SDHC/SDXC card slot. Supports up to v3.01 cards up to 128GB.
3 Reset Button Press and hold for 10 seconds while the hub is on to reset to factory default settings.
5
Sync Button
7
USB 2.0 Port
8
9
Power Input
6
Speaker
Power Button
4 LAN Port 10/100 Ethernet port. Connect this to a router to enable internet access.
5 Sync Button Press to start the camera pairing process. Maximum duration 120 seconds. Also can be pressed to stop the siren.
6 Speaker Speaker for the siren feature. Single 100dB tone.
7 USB 2.0 Port USB port for external hard drive. Does not support USB ash drives.
8 Power Button Press to turn power o/on. Down position is on, up position is o.
9 Power Input Plug the included power adapter here. 12V / 1.5A.
5D-Link DCS-2802KT-EU User Manual
Section 1 - Product Overview
Hub LED Behavior
Green Solid Powered on and functioning normally.
Power
Orange
Internet Green
Green
Camera
Power LED
Internet LED
Camera LED
Solid System is abnormal.
Blinking Currently upgrading rmware.
Solid Network link connected.
Blinking Currently transmitting network trac.
O No network connection.
Solid Camera connected and synced.
Blinking Currently pairing to a camera. Maximum duration 120 seconds.
O No cameras connected/synced.
Orange Solid No camera is bound to a mydlink account.
6D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Safety
Please read all of the safety and operating instructions before using your device:
1. Do not open the device or attempt to repair or service it.
2. When the micro-USB power connector cover is opened, only operate the device in a dry location.
3. Do not submerge the devices in liquid or attempt to clean them with liquids or solvents. To clean the devices, disconnect
from the power outlet and use a damp towel.
Before you Begin
Plan the location of your cameras:
1. Fully charge the cameras before mounting. Do not charge the cameras outdoors.
2. Make sure the cameras are placed in a location that have a consistent and adequate wireless signal to the hub.
7D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Wireless Installation Considerations
The mydlink Wire-Free Camera Kit lets you monitor locations from virtually anywhere. Keep in mind that the number, thickness and location
of surrounding buildings, foliage, or other nearby objects that the wireless signals must pass through may limit the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency) noise in your home or business area. The key to maximizing wireless
range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the camera and the hub to a minimum.
2. Building materials make a dierence. A solid metal door or aluminum studs may have a negative eect on range. If placing a
camera indoors, try to position it so that the signal passes through drywall or open doorways. Materials and objects such as glass,
steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.
3. Keep your product at least 1 to 2 meters (3 to 6 feet) from electrical devices or appliances that generate RF noise.
8D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Camera Placement Precautions
Caution:
Please make sure that the camera is not directly
facing the sun or a source of heat.
Proper Placement:
Place the camera at least 2.2 m (7 ft) or higher from the ground. The minimum recommended viewing
distance for the motion detection is 60 cm (24 in), and the maximum is 7.5 m (25 ft).
Note: The camera can be placed on a ceiling. See Ceiling Mode setting on page 18.
60 cm
64°
(24 in)
min
115°
2.2 m
(7 ft)
7.5 m
(25 ft)
max
Improper Placement:
Do not place the camera directly on top of a surface or in a spot where there is something directly below it as this will
obstruct its view
.
9D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Getting Started
To mount your camera on a wall or ceiling, please follow the steps below. It is recommended that you congure the camera before mounting.
Mounting the Camera
Snap Mount
Step 1
Identify and mark the location where you want to install the bracket, ensuring that it is at least
20 cm from the ceiling.
1
Step 2
Using a 6 mm drill bit, drill a 25 mm deep hole over the mark. For a plaster, drywall, or concrete
wall, insert the plastic anchor to support the screw rst.
Step 3
Twist the supplied screw into the wall or anchor, making sure to leave enough clearance between
the screw head and the wall.
2
3
10D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Step 4
Align the screw with the largest hole on the snap mount. Slide the mount down to lock it into place.
Step 5
Attach the back of the camera to the mount. Adjust the angle as desired.
4
5
11D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Mounting the Camera
Threaded Mount
Step 1
Place the mount at the desired location. Use a pencil to mark the holes.
Step 2
Using a 6.35 mm drill bit, drill three 25 mm deep holes over the pencil marks. For a plaster, drywall,
or concrete wall, insert the plastic anchors to support the screws rst.
1
2
Step 3
Place the baseplate over the holes. Use the supplied screws to attach the baseplate to the wall.
3
12D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Step 4
Rotate the wing nut counterclockwise with your ngers to slightly loosen it. Then move the bracket
to the approximate desired position.
Step 5
Screw the camera onto the mounting screw by tightening the plastic nger nut.
4
5
Step 6
Adjust the angle of the arm on the mounting bracket as required. Tighten the wing nut to lock the
camera's position into place.
6
13D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Setting Up the Cameras With the mydlink™ App
Please follow the instructions below to set up your Wire-Free Camera Kit.
Step 1:
Download the mydlink app from the App Store (iPhone or iPad) or Google Play
(Android).
Note: Please ensure that your device is connected to the internet.
Step 2:
Launch the mydlink app and create a new account or sign in to your existing
account.
Note: If you are asked about allowing the app to access your location, select Allow.
Make sure location services are turned on in your phone’s settings.
14D-Link DCS-2802KT-EU User Manual
Section 2 - Installation
Step 3:
After logging in, tap the Menu icon in the top-left corner, select Add New
Device and follow the on-screen instructions to connect to your camera.
Bluetooth needs to be enabled on your phone.
Step 4:
When you are asked to scan a QR code, select Yes or No.
If you selected Yes:
Scan the QR code on the back of the the hub, then press Next.
If you selected No:
Select the DCS-H100 hub from the list, then press Next.
Select Next and continue to follow the onscreen instructions.
Final Step:
Congratulations, your Wire-Free Camera Kit is now ready to use!
Be sure to check the www.mydlink.com website periodically for the latest
rmware updates to keep your product secure and up to date with the latest
features.
Note: If you experience issues registering this camera with your mydlink account, or if you
purchased an open box or resold unit, perform a hard reset by pressing and holding the
recessed reset button on the hub for 10 seconds while the device is powered on, making sure
that you see the LEDs turn o.
15D-Link DCS-2802KT-EU User Manual
Section 3 - mydlink
Using the mydlink App
Controlling Your Cameras
After setting up your cameras with a mydlink account in the mydlink app, you will be able to
remotely access your camera feeds through the app. After signing in to your mydlink account,
you will see a screen similar to the following.
If you have previously enabled "Add to shortcut" option while installing a camera, you will see
a quick link to your camera directly on the home screen.
Note: Screenshots are representative only. The mydlink app is constantly improving and so
may appear dierent.
Click on the shortcut link to your camera on the home screen and by default you will see a live
video feed of your camera on the top half of the app.
Or, you can access your DCS-2802KT-EU by tapping the Menu icon in the top-left corner,
select Devices, and select Camera. In the selected device group page, you can select the
specic camera in the carousel by tapping its icon.
16D-Link DCS-2802KT-EU User Manual
Section 3 - mydlink
Camera Options
On the bottom half of the app you will see control options for your camera.
Options Toggle
Recording Click on this button to enable recording of the video stream.
Snapshot Click on this button to take a snapshot from the video stream.
Click on this icon to review various live video options such as
speaker on/o, microphone, and video quality
17D-Link DCS-2802KT-EU User Manual
Section 3 - mydlink
Device
The Device page contains several options for you to congure your camera.
In the camera control page, after you have selected the specic camera you wish to congure, tap the
the camera’s name to enter the Device page.
1
2
3
4
1
2
3
4
5
6
Device Photo Tap to add a customized photo of this device.
Device Name Tap to change the device’s name.
Device Location
Microphone Toggle sound recording on or o.
Motion Setting Tap to adjust the motion sensitivity.
Night Vision
Tap to change or add a new location for this
device.
Click to change night vision detection to
on/o/auto.
5
7
Anti-icker Enabled anti-icker modes.
6
Click to enable Privacy Mode. Privacy Mode will
disable camera feed until you disable it again.
7
8
Privacy Mode
button to the right of
8
9
Flips the video image so the camera can be
9
Ceiling Mode
installed upside-down with the base at on the
ceiling.
18D-Link DCS-2802KT-EU User Manual
Loading...