D-Link DCS-2800KT Users guide
Minimum Requirements
To install this product, you will need:
• 802.11g/n wireless router
• Minimum recommended upload bandwidth of 1.5 Mbps for live viewing
or 3 Mbps for cloud recording.
• DCS-H100 hub (included in the DCS-2800KT Wire-Free Camera Kit)
• The latest version of the mydlink
application store.
• The mydlink app is available for iPhone®, iPad® and Android™ devices.
Please refer to the mobile app's store page to check whether your device
is compatible.
• An e-mail account (required to register for mydlink service)
Note: Please assure that your phone is connected to the same Wi-Fi network
on the router that you plan on plugging the hub into.
TM
app from your operating system’s
2
3
OR
Sign In using your mydlink account and tap the icon at the top
left, then tap Add a Device to start the setup wizard. Continue
conguration in the app.
If you select "Yes" in the app, scan the QR code on the bottom of the
camera. Continue conguration in the app.
If you select "No" in the app then select the DCS-2800LH camera from
the menu. Continue conguration in the app.
4
Wire-Free Camera
Once at the camera is synced successfully, the LED on the camera will
illuminate green to indicate it's currently connected.
Camera Placement Precautions
Caution:
Proper Placement:
Place the camera at least 2.2 m (7 ft) or higher from the ground, and at least
20cm (7.8in) from the ceiling. The minimum recommended viewing distance
for the motion detection is 60 cm (24 in), and the maximum is 7.5 m (25 ft).
2.2 m
(7 ft)
Improper Placement:
Do not place the camera directly on top of a surface or in a spot
where there is something directly below it, obstructing its view
Please make sure that the camera is
not directly facing the sun or a source
of heat.
64°
poor detection
60 cm
(24 in)
min
115°
good detection
7.5 m
(25 ft)
max
.
Camera Mounting Instructions
Snap Mount
Step 1:
Place the baseplate at the desired location, assuring
that it is at least 20cm from the ceiling. Make sure
the screw is facing up and the holes are level. Use a
pencil to mark the holes.
Step 2:
Using a 6 mm drill bit, drill two 25 mm deep holes
over the pencil marks. For a plaster, drywall, or
concrete wall, insert the plastic anchors to support
the screws rst.
Step 3:
Place the baseplate over the holes. Use the supplied
screws to attach the baseplate to the wall.
Step 4:
Align the large top screw with the largest hole on
the snap mount. Slide the mount down to lock into
place.
Step 5:
Attach the back of the camera to the mount. Adjust
the angle as desired.
Support
For toubleshooting tips and more information, visit:
support.dlink.com
1
2
3
Technical Support
Australia:
Tel: 1300-700-100
24/7 Technical Support
Web: http://www.dlink.com.au
E-mail: support@dlink.com.au
New Zealand:
Tel: 0800-900-900
24/7 Technical Support
Web: http://www.dlink.co.nz
E-mail: support@dlink.co.nz
4
5
Copyright ©2019 All rights reserved. D-Link and the D-Link logo are registered trademarks
of D-Link Corporation or its subsidiaries. Product specifications, size and shape are subject to
change without notice, and actual product appearance may differ from that depicted on the
packaging. Visit dlink.com for more details.
Version 1.00 (AU)_90x130
2019/04/02
43K-200-1691R
Quick Start Guide
DCS-2800KT
Loading...