Version 1.0 | 11/23/2015
User Manual
Full HD Ultra-Wide View Wi-Fi Camera
DCS-2630L
Manual Overview
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization
of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change. Please refer to the
www.mydlink.com website for the most current information.
Manual Revision
Revision Date Description
1.0 Nov. 23, 2015 DCS-2630L Revision A1 with rmware version 1.00
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All
other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright ©2015 by D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.
Table of Contents
Table of Contents
Product Overview ..............................................................4
Package Contents .........................................................................4
System Requirements ................................................................. 4
Introduction ................................................................................... 5
Features ............................................................................................5
Hardware Overview ..................................................................... 6
Front View ................................................................................ 6
Rear View .................................................................................7
Side View ..................................................................................7
Installation ......................................................................... 8
Wireless Installation Considerations ......................................9
Mobile App Setup ......................................................................10
Zero Conguration Setup ........................................................11
Mounting the Camera...............................................................14
mydlink ...........................................................................................16
Conguration ................................................................... 17
Audio and Video ..................................................................33
Time and Date ......................................................................35
Video Clip ..............................................................................36
Snapshot ................................................................................37
IP Filter ....................................................................................38
HTTPS Setup ......................................................................... 39
SD Recording ........................................................................40
Motion Detection ...............................................................41
Sound Detection .................................................................42
SD Management .................................................................43
Maintenance ................................................................................44
Admin .....................................................................................44
System ....................................................................................45
Firmware Upgrade ..............................................................46
Status ..............................................................................................47
Device Info ............................................................................47
Log ...........................................................................................48
Accessing the Web Conguration Utility ...........................17
Live Video ......................................................................................18
Setup ...............................................................................................20
Wizard .....................................................................................20
Network ..................................................................................28
Wireless Setup ......................................................................30
Dynamic DNS ......................................................................31
Image Setup .........................................................................32
Troubleshooting .............................................................. 49
Technical Specications .................................................. 50
Regulatory Information ..................................................52
3D-Link DCS-2630L User Manual
Section 1 - Product Overview
Product Overview
Package Contents
• DCS-2630L Full HD Ultra-Wide View Wi-Fi Camera
• Power Adapter
• Mounting Kit
• Quick Installation Guide
• Quick Install Card
Note: Using a power supply with a dierent voltage than the one included with your
product will cause damage and void the warranty for this product.
If any of the above items are missing, please contact your reseller.
System Requirements
• 802.11ac/n/g router (a D-Link Cloud Router is recommended)
• A broadband Internet connection
• iPhone, iPad, Android, or Windows smartphone or tablet (please refer to the mobile app’s store page to check whether your
device is compatible)
4D-Link DCS-2630L User Manual
Section 1 - Product Overview
Introduction
The DCS-2630L Full HD Ultra-Wide View Wi-Fi Camera boasts a horizon-wide 180° lens that easily captures your entire room, wall-to-wall, in highquality 1080p. Its rotatable head makes ceiling installations easy, and the built-in night vision, PIR motion detection, and handy mobile app empower
you with knowing exactly what is happening, day or night.
Features
180° Wide Angle Lens
The DCS-2630L provides whole-room coverage with a 180° wide angle lens, eliminating the need for multiple cameras to cover a single room.
Built-in dewarping technology automatically corrects the image for you.
1080p HD Video
The 1080p HD sensor provides crisp detail and clarity for high-quality snapshots and video.
Comprehensive Day/Night Surveillance
The built-in infrared LEDs enable night time viewing of up to 16 feet (5 meters), and the PIR sensor detects nearby motion even in complete darkness.
The microSD card slot allows the camera to record snapshots and video directly to onboard storage for a complete surveillance solution.
Wireless AC
The DCS-2630L uses high-speed Wireless AC to connect to your wireless router, and is backwards compatible with 802.11n/g/a.
Web Conguration
Using a standard web browser, you can congure and manage the DCS-2630L through the mydlink website, so you can access your DCS-2630L
anytime, anywhere in the world.
Broad Range of Applications
With today’s high-speed Internet services, the Network Camera can provide the ideal solution for delivering live video images over the Intranet and
Internet for remote monitoring. The Network Camera allows remote access using a Web browser for live image viewing, and allows the administrator
to manage and control the Network Camera anytime, anywhere in the world. Many applications exist, including industrial and public monitoring
of homes, oces, banks, hospitals, child-care centers, and amusement parks.
Remote Monitoring Utility
The D-ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to congure and access
the Network Camera from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing
up to 32 cameras on one screen, and taking snapshots.
5D-Link DCS-2630L User Manual
Section 1 - Product Overview
Hardware Overview
Front View
Microphone
Light Sensor
IR LEDs (behind cover)
Camera Lens
PIR Sensor (behind cover)
Camera Stand
6D-Link DCS-2630L User Manual
Section 1 - Product Overview
Rear View Side View
WPS Button
Power/Status LED
Reset Button
microSD Slot
MicroUSB Connector
(for power)
7D-Link DCS-2630L User Manual
Section 2 - Installation
There are two ways to set up your camera:
mydlink Lite Mobile App: You can use the mydlink Lite mobile app to guide you through setup and initial conguration of your
camera. Refer to Mobile App Setup on page 10.
Zero Conguration Setup: If you have a mydlink-enabled router (D-Link Cloud Router), this is the easiest way to set up your
camera. Refer to Zero Conguration Setup on page 11.
Installation
8D-Link DCS-2630L User Manual
Section 2 - Installation
Wireless Installation Considerations
The DCS-2630L lets you access your network using a wireless connection from anywhere within the operating range of your wireless network.
However, the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing
wireless range is to follow these basic guidelines:
1. Minimize the number of walls and ceilings between your adapter and other network devices (such as your Network Camera) - each
wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters).
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be
almost 3 feet (1 meter) thick. At a 2-degree angle, it looks over 42 feet (14 meters) thick. Position your devices so that the signal
will travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a dierence. A solid metal door or aluminum studs may weaken the wireless signal. Try to position your
access points, wireless routers, and other networking devices where the signal passes through drywall or open doorways. Materials
and objects such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade
your wireless signal.
4. Keep your product at least 3-6 feet or 1-2 meters away from electrical devices or appliances that generate RF noise.
5. If you are using 2.4GHz cordless phones or other radio frequency sources (such as microwave ovens), your wireless connection
may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as
possible. The base transmits a signal even if the phone in not in use.
9D-Link DCS-2630L User Manual
Section 2 - Installation
Mobile App Setup
You can congure your camera through the mydlink Lite mobile app. On your mobile device, download mydlink Lite by searching for mydlink Lite
in the iTunes App Store, Google Play, or the Windows Store.
Launch the mydlink Lite app and create a new account or sign in to your existing account. Follow the onscreen instructions to set up your camera.
When you are asked to scan a QR code, use the code on the Quick Install Card in your package, or on the label attached to your device.
Congratulations, your DCS-2630L is now ready to use! Be sure to check the mydlink.com website periodically for the latest rmware updates to
keep your product secure and up to date with the latest features.
10D-Link DCS-2630L User Manual
Section 2 - Installation
Zero Conguration Setup
If you have a mydlink-enabled Cloud Router, you can take advantage of Zero Conguration Setup. Zero Conguration automatically congures
your camera’s settings for you, and adds the camera to your mydlink account automatically. This type of setup allows you to set up your camera by
simply plugging it in and connecting it to your router.
Connect your camera to your mydlink-enabled Cloud Router and Zero Configuration will automatically configure your DCS-2630L and
add the camera to your mydlink account. After the short time it takes to do this you can remotely access your camera from the website
(http://www.mydlink.com) to manage and monitor your DCS-2630L.
Plug in the External Power Adapter
Connect the power adapter to the microUSB port on the back of the camera. Plug the
power adapter in to a wall outlet.
Press the WPS button on your camera
Press and hold the WPS button for three seconds. The blue WPS status LED will start blinking.
Press the WPS button on your Cloud Router
Press the WPS button on your router within 60 seconds. The WPS button is usually on
the side or back of your Cloud Router. The DCS-2630L will automatically create a secure
wireless connection to your router and reboot. When it has successfully connected, the
Power LED will be lit green and the Direct LED will be turned o.
11D-Link DCS-2630L User Manual
Section 2 - Installation
Check Your mydlink Account
From any computer with an Internet connection, open a web browser and login to your
mydlink account. The mydlink page will check for new devices and display a New device
Found! pop-up notication in the bottom-left corner. Click the notication to continue.
A summary and conrmation notication will appear with the automatically congured
details. Make a note of the details and click Yes to add the camera to your account.
DCS-2630L
DCS-2630L
12D-Link DCS-2630L User Manual
Section 2 - Installation
Zero Conguration will navigate to the mydlink Live View tab for your camera where you
will see a screen similar to the following.
Your camera is now set up, and you can skip to mydlink on page 16 to learn more about the
mydlink features of this camera, or to Conguration on page 17 for advanced conguration
of your camera.
Note: If you see a white haze when viewing in night vision mode, the night vision light on
the camera may be reecting o a nearby surface. Try repositioning and aiming the camera.
13D-Link DCS-2630L User Manual
Section 2 - Installation
Mounting the Camera
To mount your camera on a wall or ceiling, please follow the steps below. It is recommended that you congure the camera before mounting.
Step 1
Rotate the camera base cover counterclockwise, then lift it to expose the mounting holes.
Step 2
Place the camera base where you want to position the camera and use a pencil to mark the holes.
1
2
Step 3
Depending on the material of the wall or ceiling, use proper tools to drill four holes 25mm deep with a 6mm
drill bit where you marked. If the wall is made out of concrete, drill the holes rst, then insert the plastic
anchors to support the screws.
3
14D-Link DCS-2630L User Manual
Section 2 - Installation
Step 4
Place the camera base over the holes that are in the wall. Make sure to align the camera base holes with the
holes in the wall. Use the supplied screws to attach the camera to the surface of the wall.
Step 5
Reattach the base cover and turn it clockwise to lock it in place.
4
5
Step 6
Adjust the angle of the camera as desired.
6
15D-Link DCS-2630L User Manual
Section 2 - Installation
mydlink
After registering your camera with a mydlink account, you will be able to remotely access your camera from the www.mydlink.com website. After
signing in to your mydlink account, you will see a screen similar to the following:
For more details on using your camera with mydlink, go to the Support section of the mydlink website and check the User Manual section for
your product to nd the latest instruction guide for your camera’s mydlink features.
16D-Link DCS-2630L User Manual
Section 3 - Conguration
Conguration
Accessing the Web Conguration Utility
After completing the Camera Installation Wizard, you are ready to use your camera. The
camera’s built-in Web conguration utility is designed to allow you to easily access and
congure your DCS-2630L. At the end of the wizard, click Go To Camera, or enter the IP
address of your camera into a web browser, such as Internet Explorer
name admin and the password you created in the Installation Wizard. If you did not create a
password, the default password is blank. After entering your password, click OK.
Note: If you are directly connecting your PC to the camera, or if you are using the camera on
a closed network, the default IP is 192.168.0.20.
®
. To log in, use the User
Please make sure that you have the latest version of Java application installed on your computer
to ensure proper operation when viewing the video in Java mode. The Java application can
be downloaded at no cost from Sun’s web site (http://www.java.com).
When you connect to the home page of your camera, you may be prompted to download
ActiveX. If you want to use ActiveX to view your video images instead of Java, then you must
download ActiveX.
17D-Link DCS-2630L User Manual
Section 3 - Conguration
Live Video
The Live Video page lets you view the live video stream from your camera.
Please make sure that you have the latest version of Java installed on your computer to ensure proper operation when viewing the video in Java
mode. The Java application can be downloaded free from Sun’s web site (http://www.java.com).
18D-Link DCS-2630L User Manual
Section 3 - Conguration
Icon Button Name Function
Event Trigger Indicator This indicator will change color when a trigger event occurs,
such as when motion or sound is detected.
Recording Indicator When a recording is in progress, this indicator will change
color.
Prole buttons Use these buttons to switch between video proles. Refer to
Audio and Video on page 33 for more information on setting
up proles.
Full Screen button Switches to a full screen view of the camera video.
Snapshot button Takes a snapshot of the image currently displayed on the
screen and saves it to the hard drive in the folder specied
using the Storage folder button.
Video recording button Triggers the camera’s recording function. This will record the
video displayed on the screen and saves it to the hard drive in
the folder specied using the Storage folder button.
Storage folder button Sets the storage folder for snapshots and video recordings.
Listen button Sends the audio received from the camera’s microphone
through to the PC’s speakers.
Talk button Sends audio from a microphone connected to the PC through
to the speakers connected to the camera.
IR LED On/O button Turns the Infrared lights on or o.
(The icon only appears when you activate the manual IR
option. Refer to Day/Night Mode in Audio and Video on
page 33 for more.)
Zoom buttons Zooms in or out of the picture.
19D-Link DCS-2630L User Manual
Section 3 - Conguration
Setup
Wizard
This section allows you to begin setup wizards which will guide you through the process of getting your camera’s various functions congured. If
you comfortable with adjusting the settings manually, you may skip the wizards and adjust settings manually as needed.
Internet
Connection
Setup Wizard:
Manual
Internet
Connection
Setup:
Motion
Detection
Setup Wizard:
Manual Motion
Detection
Setup:
You may choose to congure your network by
using the Internet Connection Setup Wizard
that includes step-by-step instructions.
Please refer to Internet Connection Setup
Wizard on page 21 for more details.
If you would rather manually set up the
camera internet connection, you can refer
to Network on page 28 which provides more
details on the information required.
You may choose to congure motion
detection by using the Motion Detection
Setup Wizard that includes step-by-step
instructions. Please refer to Motion Detection
Setup Wizard on page 24 for more details.
If you would rather manually set up the
camera’s motion detection features, you can
refer to Motion Detection on page 41 which
provides more details on the information
required.
20D-Link DCS-2630L User Manual
Section 3 - Conguration
Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to congure your new D-Link
Camera and connect the camera to the Internet.
Click Next to continue.
Select how the camera will connect to the Internet. If you are unsure how your camera will
connect to the Internet, select Automatic IP. If your ISP has assigned you a static IP, select
Static IP Address and enter the following details:
IP Address:
Subnet Mask:
Default
Gateway
(Router):
Optional
Primary DNS:
Optional
Secondary
DNS:
Enter the IP address that the camera will use on your network. You may
need to get this information from your ISP or network administrator.
The default value is “255.255.255.0.” Used to determine if the destination
is part of the same network segment.
The gateway used to forward data to destinations in a dierent subnet.
Invalid gateway settings may cause the failure of transmissions to a
dierent subnet.
Primary domain name server that translates names to IP addresses.
Secondary domain name server to backup the Primary DNS.
Click Next to continue.
21D-Link DCS-2630L User Manual
Section 3 - Conguration
If you are required to connect using PPPoE, select Enabled and enter the Username and
Password for your PPPoE connection.
A Dynamic DNS account allows you to access your camera over the Internet when you
have an IP address that changes each time you connect to the Internet. If you have a
Dynamic DNS account, click Enable and enter the following details:
Server Address:
Host Name:
User Name:
Password:
Timeout:
Enter a name for your camera. Click Next to continue.
Select your Dynamic DNS Server from the pull down menu.
Enter the host name of the DDNS server.
Enter your username or e-mail address used to connect to the DDNS.
Enter your password used to connect to the DDNS server.
You can setup how often the camera noties the DDNS server of its
current global IP address by entering a whole number in hours.
Click Next to continue.
22D-Link DCS-2630L User Manual
Section 3 - Conguration
Select the time zone that the camera is in so that scheduled events occur at the correct
time. If your time zone observes daylight saving, check the Enable Daylight Saving box
and select Auto Daylight Saving to have DST set automatically or select Set date and time
manually to enable drop down menus so that you can set the start and end time of daylight
saving yourself.
Click Next to continue.
A summary of the options you selected is displayed for conrmation. If you are happy with
the selected conguration, click Apply. Otherwise, click Back to make the required changes.
23D-Link DCS-2630L User Manual
Section 3 - Conguration
Motion Detection Setup Wizard
This wizard will guide you through a step-by-step process to congure the motion
detection feature of your new D-Link Camera
Click Next to continue.
Enabling the Video Motion option will allow your camera to use the motion detection feature.
You may draw areas for your camera to monitor for motion..
Enable Video
Motion:
Enable PIR:
Sensitivity:
Drawing Mode:
Clear:
Select this box to enable the video motion detection feature of your
camera. Make sure you draw an area for the camera to monitor for motion.
When this option is selected, the camera will use PIR (passive infrared) to
detect motion. Use the PIR Sensitivity drop-down box to determine how
sensitive the PIR sensor will be to motion.
Species how sensitive video motion detection will be from 0% to 100%.
A low sensitivity setting means that there must be large changes between
two images in order to detect motion, and a high sensitivity setting means
that even small changes will cause motion to be detected.
Select Draw Motion Area to select the area of the picture to monitor for
movement to trigger recording or a snapshot. Use your mouse to click
and drag on the area that you would like to monitor for motion. Select
Erase Motion Area to clear a selected region and stop the camera from
monitoring that area of the picture.
Clears all motion detection areas from the picture.
Click Save Settings to save your changes.
24D-Link DCS-2630L User Manual
Section 3 - Conguration
Snapshot Notications is a feature to send image snapshots via FTP or e-mail when motion
is detected.
Enable:
Only During:
Snapshot Type:
Target:
Check this box to enable the Snapshot function.
Check this box to setup a scheduled timeframe when notications should
be sent. This is useful if you do not want to be notied when it would
otherwise be inconvenient, such as during the night or on weekends.
Select whether to take a single snapshot or to take 6 snapshots with a 1
second interval between them.
Select where you want the snapshot to be sent. It may be uploaded to an
FTP or sent to an e-mail address. You will need to have all of the necessary
information lled out in order to use either of these features.
Click Next to continue.
25D-Link DCS-2630L User Manual
Section 3 - Conguration
Video Clip Notications is a feature to send video clips via FTP or e-mail when motion is
detected.
Enable:
Only During:
Video Clip
Type:
Target:
Check this box to enable the Video Clip function.
Check this box to setup a scheduled timeframe when video clips should
be sent. This is useful if you do not want to be notied when it would
otherwise be inconvenient, such as during the night or on weekends.
The Video Clip Wizard uses Prole 2 by default. More information about
video proles can be found in Audio and Video on page 33. You can set
the le type from the drop down menu. You can also specify how many
seconds before the event that triggered recording should be sent, as
well as how long the maximum duration of the video clip should be in
seconds.
Select where you want the video clip to be sent. It may either be uploaded
to an FTP or sent to an e-mail address. You will need to have all of the
necessary information lled out in order to use either of these features.
Click Next to continue.
26D-Link DCS-2630L User Manual
Section 3 - Conguration
SD Recording Notications is a feature to record video to the microSD card when motion is
detected. The microSD card must be formatted for use with the camera prior to running the
wizard. This can be done by using the format option found under SD Management. For more
details, please refer to SD Management on page 46.
Enable:
Only During:
SD Recording
Type:
Keep Free
Space:
Cyclic
Check this box to enable the SD Recording function.
Check this box to setup a scheduled timeframe when recording should
take place. This is useful if you do not want to be recorded when it would
otherwise be inconvenient, such as during the night or on weekends.
The SD Recording Wizard uses Prole 2 by default. More information
about video proles can be found in Audio and Video on page 33. You
can set the le type from the drop down menu. You can also specify how
many seconds before and after the event should be recorded, as well as
how long the maximum duration of the video clip should be in minutes.
Set amount of space to keep free on the microSD card.
When this option is selected, it will cause the oldest snapshot/video les
to be deleted when the system requires storage space for new snapshot/
video les.
Click Next to continue.
A summary of the options you selected is displayed for conrmation. If you are happy with
the selected conguration, click Apply. Otherwise, click Back to make the required changes.
27D-Link DCS-2630L User Manual
Section 3 - Conguration
This section allows you to congure your network settings.
Network
Automatic IP
Address:
Static IP
Address:
Select this connection if you have a DHCP server running on your network
and would like a dynamic IP address to be updated to your camera
automatically.
You may obtain a static or xed IP address and other network information
from your network administrator for your camera.
IPv4 Address: Enter the IP address that the camera will use on your
network. You may need to get this information from your ISP or network
administrator.
Subnet Mask: The default value is “255.255.255.0.” Used to determine if
the destination is part of the same subnet.
Default Gateway: The gateway used to forward frames to destinations
in a dierent subnet. Invalid gateway settings may cause the failure of
transmissions to a dierent subnet.
Optional Primary DNS: Primary domain name server that translates
names to IP addresses.
PPPoE
Settings:
IPv6 Settings:
Optional Secondary DNS: Secondary domain name server to backup the
Primary DNS.
If you are using a PPPoE connection, enable it and enter the User Name
and Password for your PPPoE account. You can get this information from
your Internet service provider (ISP).
Select Automatic IP Address to automatically get an IPv6 address from
your router. If you have a static or xed IP from your network administrator,
select Static IP address and enter the information provided by your ISP or
network administrator.
28D-Link DCS-2630L User Manual
Section 3 - Conguration
Port Settings:
UPnP:
UPnP Port
Forward:
Bonjour:
You may congure which ports to use for HTTP, HTTPS, and RTSP access
to the camera.
Enable this setting to congure your camera as an UPnP device in the
network.
Enable this to allow your camera to use UPnP to congure port forwarding
on your router.
Checking the Bonjour box will allow the camera to be discoverable on
the network and visible to Apple devices.
Click Save Settings to save your changes.
29D-Link DCS-2630L User Manual
Section 3 - Conguration
Wireless Setup
This section allows you to set up and congure the wireless settings on your camera.
Network Name:
Site Survey:
Wireless Mode:
Security Mode:
Cipher Type:
Key:
Enter the SSID/name for the wireless network you want to connect to, or
use the Site Survey drop down menu to select an existing one.
The drop down menu lists all the wireless networks that the camera was
able to detect. Click Rescan to scan for wireless networks again.
This shows the current wireless mode being used by the camera.
For security, you can choose None or WPA-PSK / WPA2-PSK. Select the
same encryption method that is being used by your wireless device/
router.
If you chose WPA-PSK or WPA2-PSK, choose whether to use TKIP or AES.
Enter the key(password) for your wireless network. Check the Show
Hidden Key box to reveal the password you have entered.
Click the Save Settings button to save your changes.
30D-Link DCS-2630L User Manual
Section 3 - Conguration
Dynamic DNS
DDNS allows you to access your camera using a domain name instead of an IP address. To do this, you will need to have an account with one of the
DDNS services listed in the drop-down box on this page.
DDNS:
Server Address:
Host Name:
User Name:
Password:
Timeout:
Status:
Check this box to enable the DDNS function.
Select your Dynamic DNS Server from the drop down menu.
Enter the host name of the DDNS server.
Enter the username or e-mail address used to connect to the DDNS server.
Enter the password used to connect to the DDNS server.
You can set up how often the camera noties the DDNS server of its
current global IP address by entering a whole number in hours.
This shows the current status of your DDNS updates.
Click the Save Settings button to save your changes.
31D-Link DCS-2630L User Manual
Section 3 - Conguration
Image Setup
This section allows you to congure the image settings for your camera.
Brightness:
Saturation:
Contrast:
Sharpness:
B/W:
Mirror:
Flip:
Frequency:
Allows you to adjust the brightness level.
Allows you to adjust the saturation level.
Allows you to adjust the contrast level.
Allows you to adjust the sharpness level.
Changes the images recorded on the camera to be in black and white.
Horizontally ip the video.
Select this box to vertically ip the video. If the camera is installed upside
down, Flip Image and Mirror should both be checked.
Select the frequency used by your power lines to avoid camera icker
or moving bars in your video. Generally, if your power outlets are 220 to
240 V, you should select 50 Hz. If your power outlets are 100 to 120 V, you
should select 60 Hz.
Changes made to these settings will take eect immediately.
32D-Link DCS-2630L User Manual
Section 3 - Conguration
Audio and Video
This section allows you to congure the audio and video settings for your camera.
Video Prole:
Encode Type:
Resolution:
FPS:
Encode
Method:
bps:
There are three individual proles that can be congured. Prole 2 is used
for snapshots, and Prole 3 is used for mobile devices.
This is the video encoding the prole uses. These are xed for each prole.
Select the desired video resolution for the video prole: 1920 x 1080,
1280 x 720, 640 x 352, or 320 x 176. Higher resolutions will provide a higher
quality image, but will require more network bandwidth and create larger
saved les.
Set the desired FPS for the video prole. A higher FPS will result in
smoother video playback, but will require more network bandwidth and
create larger saved les.
This is the encode method the prole uses. These are xed for each prole.
Select the bit rate to assign the video. The bps setting is used as a maximum
limit for the amount of data the camera will use. Higher settings will
provide a higher quality image, but will require more network bandwidth
and create larger saved les.
Quality:
One of ve levels of image quality can be set for the snapshot feature:
Highest, High, Medium, Low, and Lowest. This setting is for Prole 2 only.
33D-Link DCS-2630L User Manual
Section 3 - Conguration
RTSP URL:
Day/Night
Mode:
This is the URL used to connect to the camera when viewing from
QuickTime or a mobile device. For instance, live1.sdp can be accessed
at rtsp://x.x.x.x/video1.sdp where the x.x.x.x represents the IP address of
your camera.
Select a method of switching between day and night modes. During day
mode, the IR cut lter will be used to ensure that your video will have the
correct colors. During night mode, the IR LEDs will be turned on and the
IR cut lter moves out of the way to give the camera night vision.
• Auto: This will automatically switch between day and night mode
based on the amount of ambient light. When there is enough light,
day mode will be used. When it gets dark, the camera will switch to
night mode.
You can use the Light Sensor Sensitivity drop-down box to
determine how sensitive the camera’s light sensor will be and how
quickly your camera will respond to changes in ambient light.
• Manual: The camera will only switch between day and night mode
when requested to through the Live Video interface on the mydlink
website or mobile app.
• Always Day Mode: The camera will always use day mode.
• Always Night Mode: The camera will always use night mode.
• Day Mode Schedule: This option lets you use a schedule to switch
between day and night mode. Enter the times you want the camera
to use day mode. The camera will use night mode for all times
outside of this schedule.
Audio Setup:
Allows you to enable and disable or adjust the volume levels of the
speaker and microphone.
Click Save Settings to save your changes.
34D-Link DCS-2630L User Manual
Section 3 - Conguration
Time and Date
This section allows you to congure the settings of the internal system clock for your camera.
Time Zone:
Enable
Daylight
Saving:
Synchronize
NTP Server:
Set the Date
and Time
Manually:
Select the time zone for your region from the drop down menu.
If your region uses Daylight Saving time, you can enable it here. Select
Set DST Manually if you want to manually set the oset and the period
of time that the Daylight Saving correction should be used.
Network Time Protocol (NTP) will synchronize your camera with an
Internet time server. Choose the one that is closest to your camera,
or select Get NTP Server from DHCP to try and get the NTP server
information automatically from your DHCP server.
If Synchronize NTP Server is disabled, you can set the date and time
manually. You can also click the Copy Your Computer’s Time Settings
button to automatically copy the date and time of the PC you are using.
Click Save Settings to save your changes.
35D-Link DCS-2630L User Manual
Section 3 - Conguration
Video Clip
Video Clip allows you to send video clips via FTP or e-mail when a trigger is activated. You can send video clips to an FTP server or an e-mail address.
Video Clip:
Trigger By:
Video Clip
Type:
Check this box to enable the Video Clip function.
Select whether to record a video clip when triggered by Motion or Sound,
according to a Schedule, or Always record.
• Motion: Enables recording when motion is detected. You can limit
motion-triggered recording to a specic schedule by selection Only
during and entering the times you want motion-triggered recording
to be enabled.
• Schedule: Enables recording according to a schedule. Enter the times
you want the camera to record.
• Always: This will enable continuous recording.
• Sound: Enables recording when sound is detected. You can limit
sound-triggered recording to a specic schedule by selection Only
during and entering the times you want sound-triggered recording
to be enabled.
You may choose Video Prole 1 or 3 and select the le format and
recording length. For more on video prole options, refer to Audio and
Video on page 33.
Target:
Select where you want the video clip to be sent. It may be uploaded to
an FTP server or sent to an e-mail address. Enter the settings for your FTP
server or e-mail account.
Click Save Settings to save your changes.
36D-Link DCS-2630L User Manual
Section 3 - Conguration
Snapshot
The snapshot feature lets you send image snapshots via FTP or e-mail when a trigger is activated. You can send snapshots to both an FTP server
and an e-mail address.
Snapshot:
Trigger By:
Snapshot Type:
Check this box to enable the Snapshot function.
Select whether to record a snapshot when triggered by Motion or Sound,
according to a Schedule, or Always record.
• Motion: Enables recording when motion is detected. You can limit
motion-triggered recording to a specic schedule by selection Only
during and entering the times you want motion-triggered recording
to be enabled.
• Schedule: Enables recording according to a schedule. Enter the times
you want the camera to record. During these times, a snapshot will be
taken every second.
• Always: This will enable continuous recording. A snapshot will be
taken every second.
• Sound: Enables recording when sound is detected. You can limit
sound-triggered recording to a specic schedule by selection Only
during and entering the times you want sound-triggered recording
to be enabled.
Select whether to take a single snapshot or to take 6 snapshots with a
selectable interval between them. Snapshots will always use Video Prole
2. For more on video prole options, refer to Audio and Video on page 33.
Target:
Select where you want the snapshot to be sent. It may be uploaded to
an FTP server or sent to an e-mail address. Enter the settings for your FTP
server or e-mail account.
Click Save Settings to save your changes.
37D-Link DCS-2630L User Manual
Section 3 - Conguration
IP Filter
The IP Filter is a feature used to allow or deny certain IP addresses when accessing the DCS-2630L. Please note that when creating an allow list, if the
IP address of your computer is not included or if you do not set up an administrator IP address, you may be locked out of accessing your camera. In
this event, you will need to do a hard reset of your camera by pressing the reset button for more than 10 seconds while it is powered on.
Access List
Filtering:
Filter Type:
IPv4 Filter List:
IPv6 Filter List:
Add New Filter.
Administrator
IP Address.
Check this box to enable the IP Filter function.
Select whether to set the lter to allow or to deny connection from the IP
addresses listed.
The current list of IPv4 addresses that are being ltered. Select a line and
the click the delete button to remove that entry.
The current list of IPv6 addresses that are being ltered. Select a line and
the click the delete button to remove that entry.
From the drop down menu, select whether to add a single IP, an entire
subnet, or a range of IP addresses. Enter an IP address, subnet, or IP range,
then click Add to create a new lter.
You can allow a single IP address to always have access to this camera,
regardless of the IP lter rules being used, by enabling this option and
entering the IP address.
Click Save Settings to save your changes.
38D-Link DCS-2630L User Manual
Section 3 - Conguration
HTTPS Setup
HTTPS Setup is used to add encryption to the HTTP connection, making it more secure and less susceptible to unauthorized use.
HTTPS Secure
Connection:
Connection
Type:
Create
and Install
Certicate
Method:
Certicate
Information:
Check this box to enable the HTTPS function.
Select whether the connection type should be HTTP and HTTPS or only
HTTPS.
Select whether to create a self-signed certicate automatically, manually,
or to request and install a certicate from an authority. If you choose
to manually create a certicate or request and install one, enter the
requested information.
General information and the status of the current HTTPS certicate is
displayed. If you would like to see more detailed information, click on
the Property button. If you would like to remove the certicate, click the
Remove button.
Click Save Settings to save your changes.
39D-Link DCS-2630L User Manual
Section 3 - Conguration
SD Recording
This option allows you to congure and set a schedule for the recording to an inserted microSD card.
SD Recording:
Trigger by:
Recording
Type:
Check this box to enable the recording feature.
Select whether the event is activated by Motion, Schedule, or if the video
is Always recording.
• Motion: Enables recording when motion is detected. You can limit
motion-triggered recording to a specic schedule by selection Only
during and entering the times you want motion-triggered recording
to be enabled.
• Schedule: Enables recording according to a schedule. Enter the times
you want the camera to record. If you are recording snapshots, a
snapshot will be taken every second during these times.
• Always: This will enable continuous recording. If you are recording
snapshots, a snapshot will be taken every second.
• Sound: Enables recording when sound is detected. You can limit
sound-triggered recording to a specic schedule by selection Only
during and entering the times you want sound-triggered recording
to be enabled.
You can choose to record snapshots or video. Snapshots will use Video
Prole 2. For video recordings, you may choose Video Prole 1 or 3 and
select the le format and recording length. For more on video prole
options, refer to Audio and Video on page 33.
Keep Free
Space:
Cyclic:
Set amount of space to keep free on the microSD card.
When this option is selected, it will cause the oldest snapshot/video les
to be deleted when the system requires storage space for new snapshot/
video les.
Click Save Settings to save your changes.
40D-Link DCS-2630L User Manual
Section 3 - Conguration
Motion Detection
Motion detection enables the camera to monitor the video feed for movement. You can also enable motion detection via the PIR sensor.
Enable Video
Motion:
Enable PIR:
Sensitivity:
Drawing Mode:
Clear:
Select this box to enable the video motion detection feature of your
camera. Make sure you draw an area for the camera to monitor for motion.
When this option is selected, the camera will use PIR (passive infrared) to
detect motion. Use the PIR Sensitivity drop-down box to determine how
sensitive the PIR sensor will be to motion.
Species how sensitive video motion detection will be from 0% to 100%.
A low sensitivity setting means that there must be large changes between
two images in order to detect motion, and a high sensitivity setting means
that even small changes will cause motion to be detected.
Select Draw Motion Area to select the area of the picture to monitor for
movement to trigger recording or a snapshot. Use your mouse to click
and drag on the area that you would like to monitor for motion. Select
Erase Motion Area to clear a selected region and stop the camera from
monitoring that area of the picture.
Clears all motion detection areas from the picture.
Click Save Settings to save your changes.
41D-Link DCS-2630L User Manual
Section 3 - Conguration
Sound Detection
Sound detection enables the camera to monitor the environment for loud sounds. You may set the volume threshold used to determine whether
sound was detected or not. If this option is selected, the trigger by option under Video Clip, Snapshot, or SD Recording should also be selected.
Sound
Detection:
Detection
Level:
Select this box to enable the sound detection feature of your camera.
Specify the volume level that a sound must exceed in order to trigger the
sound detection feature. The lower the number, the more sensitive the
camera will be to sound.
Click Save Settings to save your changes.
42D-Link DCS-2630L User Manual
Section 3 - Conguration
SD Management
Here you may browse and manage the recorded les which are stored on the microSD card. Click on a folder or le to open it.
SD Card:
SD Status:
Files Per Page:
Refresh:
Format SD
Card:
Deleting Files
and Folders:
This shows the current folder on the microSD card that you are viewing.
Click on an earlier folder name to return to it.
This shows the current microSD card status.
Use the drop-down box to specify how many les to show per page. To
change pages, use the drop-down box on the right.
Click this to refresh the le and folder information from the microSD card.
Click this button to automatically format the microSD card.
Note: SD Recording must be disabled in order to format the microSD
card. See SD Recording on page 40 for more details.
To delete les and folders, click on the checkbox next to the les or folders
you want to delete, then click the Delete button. To select all of the les
or folders shown, click on the checkbox next to the Delete button.
43D-Link DCS-2630L User Manual
Section 3 - Conguration
Maintenance
Admin
This section allows you to change the administrator’s password and congure the server settings for your camera. You can also manage the user
account(s) that access your camera.
Admin
Password
Setting:
Add User
Account:
User List:
RTSP
Authentication:
HTTP
Authentication:
Snapshot URL
Authentication:
Camera Name:
To change your password, enter your current password and then enter
the new one in the New Password and Conrm New Password elds.
Create a new user to access the camera’s Live Video page. Enter the user
name, password, and password conrmation, and click Add.
Select a user from the drop down menu and click Delete to remove the
user account.
Enables user validation for RTSP streaming.
Enables user validation for HTTP streaming.
Select this to allow access to the current camera snapshot via the web
address indicated.
Specify a name for your camera.
OSD:
Power/Link
LED Light:
Enabling this will show information in the top left of the camera’s video.
In the Label eld, you may enter a name to display on the image. Select
Time Stamp to include the current date and time.
Select Normal to enable the LED on the front of the device, or select O
to disable the LED.
44D-Link DCS-2630L User Manual
Section 3 - Conguration
System
This section allows you to save and restore your conguration, restore the factory settings, and/or restart the camera.
Save To Local
Hard Drive:
Load From
Local Hard
Drive:
Restore
To Factory
Defaults:
Reboot The
Device:
Schedule
Device Reboot
You may save your current camera conguration as a le on your computer
by clicking Save Conguration.
Locate a pre-saved conguration by clicking Browse... and then restore
the pre-dened settings to your camera by clicking Load Conguration.
You may reset your camera and restore the factory settings by clicking
Restore Factory Defaults.
This will restart your camera.
You can schedule the camera to reboot according to a schedule. Select
the days and time you want the camera to automatically reboot.
45D-Link DCS-2630L User Manual
Section 3 - Conguration
Firmware Upgrade
The camera’s current rmware version will be displayed on this screen. You may visit the D-Link Support Website to check for the latest available
rmware version.
To upgrade the rmware on your DCS-2630L, please download and save the latest rmware version from the D-Link Support Page to your local
hard drive. Locate the le on your local hard drive by clicking the Browse button. Select the le and click the Upload button to start upgrading
the rmware.
46D-Link DCS-2630L User Manual
Section 3 - Conguration
Status
Device Info
This section displays information about your camera and its current network and wireless status.
47D-Link DCS-2630L User Manual
Section 3 - Conguration
Log
This page displays the log information of your camera. You may download the information by clicking Download. You may also click Clear to delete
the saved log information. The log will also be cleared when the camera is rebooted.
48D-Link DCS-2630L User Manual
Section 4 - Troubleshooting
Troubleshooting
1. Why is the camera view hazy or bright when using night vision mode?
The IR night vision lights on your camera may be reecting o of a nearby surface or window. Try repositioning your camera to avoid reections
or glare.
2. What can I do if I forget my camera password?
If you forget your password, you will need to perform a hard reset of your camera. This process will change all your settings back to the factory
defaults.
To reset your camera, please use an unfolded paperclip to press and hold the Reset button for at least 10 seconds while your camera is plugged in.
3. What can I do if my camera is not working correctly?
First, reset the camera and try setting the camera up again.
To make sure your hardware is installed correctly, make sure that:
• the power LED is solid green
• your Internet connection is working
• your router’s LAN & WAN connections are working
• your router supports UPNP
• your camera is on the same network as your mobile device
• both your mobile device and camera have a working Internet connection
If your camera is still not working, check your router and make sure it has the latest rmware.
49D-Link DCS-2630L User Manual
Appendix A - Technical Specications
Camera
Technical Specications
Camera Hardware Profile • 1/3” 3 Megapixel progressive CMOS sensor
• 5 meter IR illumination distance
• Minimum illumination:
• Color (Day Mode), IR LEDs off: 0.1 lux
• B/W (Night Mode), IR LEDs off: 0.05 lux
• B/W (Night Mode), IR LEDs on: 0 lux
• Built-in Infrared-Cut Removable (ICR) Filter module
• 8X digital zoom
• Fixed length 1.72 mm
Image Features • Configurable image size, quality, frame rate, and bit rate
• Configurable brightness, contrast, sharpness, saturation, and hue
Video Compression • Simultaneous H.264/MJPEG format compression • JPEG for still images
Video Resolution • 1920 x 1080, 1280 x 720, 640 x 352, 320 x 176 at up to 30 fps
Audio Compression • ADPCM
• G.711
Connectivity • 802.11ac/n/g/b wireless with WPA/WPA2 encryption
• Operates on 2.4 GHz and 5 GHz bands
• Aperture F2.0
• Angle of view
• (H) 180°
• (V) 112°
• (D) 180°
• Image de-warping
• Minimum object distance: 50 cm
• Built-in microphone and speaker
• Configurable motion detection windows
• Time stamp and text overlays
• μ-law PCM
• Maximum data rate of 433 Mbps (PHY rate)
Network
Network Protocols • IPV4, ARP, TCP, UDP, ICMP
• DHCP Client
• NTP Client (D-Link)
• DNS Client
• DDNS Client (D-Link)
• SMTP Client
• FTP Client
• HTTP Server
• PPPoE
• RTP, RTSP, RTCP
• UPnP Port Forwarding
• HTTPS for configuration
• Bonjour
1
Security • Administrator and user group protection
• Password authentication
• HTTP and RTSP digest encryption
50D-Link DCS-2630L User Manual
Appendix A - Technical Specications
83 .00 m m
53. 70 mm
36. 61 mm
System Integration
System Requirements for Web Interface • Operating system: Microsoft Windows 10/8/7 or Mac OS X 10.7 or higher • Browser: Internet Explorer 8, Firefox 12, or Safari 6 or higher
Event Management • Motion detection
• Event notification and uploading of snapshots/video clips via SMTP or FTP
• Sound level detection
Remote Management • Configuration accessible via web browser
Mobile support • mydlink Lite app for iPhone, iPad, iPod Touch, Android, and Windows • mydlink+ app for iOS and Android
General
Dimensions • 85.6 x 85.6 x 140.0 mm (3.37 inches x 3.37 inches x 5.51 inches)
Weight • 345.0 grams (12.2 ounces) ± 5%
Power • 5 V DC, 2 A through external power adapter
Power Consumption • 3.5 watts maximum ± 5%
Temperature • Operating: 0 to 40 °C (32 to 104 °F) • Storage: -20 to 70˚ C (-4 to 158 ˚F)
Humidity • Operating: 20% to 80% non-condensing • Storage: 20% to 80% non-condensing
Certifications • CE
• CE LVD
Dimensions Diagram
83.0 mm
• FCC Class B
• ICES
53.70 mm
36.61 mm
140.0 mm
Ø 85.6 mm
51D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Non-modications Statement:
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance
with FCC multi-transmitter product procedures. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection
of other channels is not possible.
Note
The country code selection is for non-USA models only and is not available to all USA models. Per FCC regulations, all WiFi product marketed in
the USA must be xed to USA operational channels only.
52D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
RF Frequency Requirements
This device is for indoor use only when using all channels in the 5.150GHz-5.250GHz, 5.250GHz-5.350GHz, 5.470GHz-5.725GHz, 5.725GHz-
5.850GHz frequency range. High power radars are allocated as primary users of the 5.150GHz-5.250GHz, 5.250GHz-5.350GHz, 5.470GHz-
5.725GHz, 5.725GHz-5.850GHz GHz bands. These radar stations can cause interference with and/or damage this device. This device will not
operate on channels which overlap the 5600-5650 MHz band.
It is restricted to indoor environments only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
Industry Canada Statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d'en compromettre le
fonctionnement.
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems;
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur an de réduire les risques
de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
Operations in the 5.25-5.35 GHz band are restricted to indoor usage only.
Les opérations dans la bande de 5.25-5.35 GHz sont limités à un usage intérieur seulement.
53D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
European Union:
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. For more information, please refer to the Declaration of
Conformity.
Notice of Wireless Radio LAN Usage in The European Community:
• At the time of writing this addendum, some countries such as Italy, Greece, Portugal, and Spain have not allowed operation of radio devices
in the 5 GHz bands, although operation of 2.4 GHz radio devices is allowed. Please check with your local authority to conrm.
• This device is restricted to indoor use when operated in the European Community using channels in the 5.15-5.35 GHz band to reduce the
potential for interference.
• This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in
France where restrictive use applies. This device may not be used for setting up outdoor radio links in France and in some areas the RF output
power may be limited to 10 mW EIRP in the frequency range of 2454 –2483.5 MHz. For detailed information the end-user should contact the
national spectrum authority in France.
This equipment may be operated in AL, AD, BE, BG, DK, DE, FI, FR, GR, GW, IS, IT, HR, LI, LU, MT, MK, MD, MC, NL, NO, AT, OL, PT, RO, SM, SE, RS, SK,
ES, CI, HU, CY
Usage Notes:
• To remain in conformance with European National spectrum usage regulations, frequency and channel limitations will be applied on the
products according to the country where the equipment will be deployed.
• This device is restricted from functioning in Ad-hoc mode while operating in 5 GHz. Ad-hoc mode is direct peer-to-peer communication
between two client devices without an Access Point.
• Access points will support DFS (Dynamic Frequency Selection) and TPC (Transmit Power Control) functionality as required when operating in
5 GHz within the EU.
54D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
5 GHz Wireless Frequency and Channel Operation in EEC Countries:
Allowable 802.11a Frequencies and Channels Countries
5.15-5.25 GHz
(Channels 36, 40, 44, 48)
5.15-5.25 GHz & 5.725-5.875 GHz
(Channels 36, 40, 44, 48, 149, 153, 157, 161, 165, 169)
5.15-5.35 GHz
(Channels 36, 40, 44, 48, 52, 56, 60, 64)
5.15-5.35 & 5.47-5.725 GHz
(Channels 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136,
140)
5.15-5.35 GHz & 5.725-5.875 GHz
(Channels 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165, 169)
Liechtenstein
Austria
France
Denmark, Germany, Iceland, Finland, Netherlands,
Norway, Poland, Sweden, Slovenia, Luxembourg, U.K.,
Ireland, Slovak, Switzerland, Hungary, Italy
Czech Republic
55D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
Disposing of and Recycling Your Product
ENGLISH EN
This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed
of in household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has
reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help
to conserve the environment and protect human health.
D-Link and the Environment
At D-Link, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimise
this impact D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both
products and packaging.
D-Link recommends that you always switch o or unplug your D-Link products when they are not in use. By doing so you will help to save energy
and reduce CO2 emissions.
To learn more about our environmentally responsible products and packaging please visit www.dlinkgreen.com.
DEUTSCH DE
Dieses Symbol auf dem Produkt oder der Verpackung weist darauf hin, dass dieses Produkt gemäß bestehender örtlicher Gesetze
und Vorschriften nicht über den normalen Hausmüll entsorgt werden sollte, sondern einer Wiederverwertung zuzuführen ist. Bringen
Sie es bitte zu einer von Ihrer Kommunalbehörde entsprechend amtlich ausgewiesenen Sammelstelle, sobald das Produkt das Ende
seiner Nutzungsdauer erreicht hat. Für die Annahme solcher Produkte erheben einige dieser Stellen keine Gebühren. Durch ein auf
diese Weise durchgeführtes Recycling des Produkts und seiner Verpackung helfen Sie, die Umwelt zu schonen und die menschliche
Gesundheit zu schützen.
D-Link und die Umwelt
D-Link ist sich den möglichen Auswirkungen seiner Geschäftstätigkeiten und seiner Produkte auf die Umwelt bewusst und fühlt sich verpichtet,
diese entsprechend zu mindern. Zu diesem Zweck entwickelt und stellt D-Link seine Produkte mit dem Ziel größtmöglicher Umweltfreundlichkeit
her und verwendet wiederverwertbare, schadstoarme Materialien bei Produktherstellung und Verpackung.
D-Link empehlt, Ihre Produkte von D-Link, wenn nicht in Gebrauch, immer auszuschalten oder vom Netz zu nehmen. Auf diese Weise helfen
Sie, Energie zu sparen und CO2-Emissionen zu reduzieren.
Wenn Sie mehr über unsere umweltgerechten Produkte und Verpackungen wissen möchten, nden Sie entsprechende Informationen im Internet
unter www.dlinkgreen.com.
56D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
FRANÇAIS FR
Ce symbole apposé sur le produit ou son emballage signie que, conformément aux lois et règlementations locales, ce produit ne
doit pas être éliminé avec les déchets domestiques mais recyclé. Veuillez le rapporter à un point de collecte prévu à cet eet par les
autorités locales; certains accepteront vos produits gratuitement. En recyclant le produit et son emballage de cette manière, vous
aidez à préserver l’environnement et à protéger la santé de l’homme.
D-Link et l’environnement
Chez D-Link, nous sommes conscients de l'impact de nos opérations et produits sur l'environnement et nous engageons à le réduire. Pour limiter
cet impact, D-Link conçoit et fabrique ses produits de manière aussi écologique que possible, en utilisant des matériaux recyclables et faiblement
toxiques, tant dans ses produits que ses emballages.
D-Link recommande de toujours éteindre ou débrancher vos produits D-Link lorsque vous ne les utilisez pas. Vous réaliserez ainsi des économies
d’énergie et réduirez vos émissions de CO2.
Pour en savoir plus sur les produits et emballages respectueux de l’environnement, veuillez consulter le www.dlinkgreen.com.
ESPAÑOL ES
Este símbolo en el producto o el embalaje signica que, de acuerdo con la legislación y la normativa local, este producto no se debe
desechar en la basura doméstica sino que se debe reciclar. Llévelo a un punto de recogida designado por las autoridades locales una
vez que ha llegado al n de su vida útil; algunos de ellos aceptan recogerlos de forma gratuita. Al reciclar el producto y su embalaje
de esta forma, contribuye a preservar el medio ambiente y a proteger la salud de los seres humanos.
D-Link y el medio ambiente
En D-Link, comprendemos y estamos comprometidos con la reducción del impacto que puedan tener nuestras actividades y nuestros productos
en el medio ambiente. Para reducir este impacto, D-Link diseña y fabrica sus productos para que sean lo más ecológicos posible, utilizando
materiales reciclables y de baja toxicidad tanto en los productos como en el embalaje.
D-Link recomienda apagar o desenchufar los productos D-Link cuando no se estén utilizando. Al hacerlo, contribuirá a ahorrar energía y a reducir
las emisiones de CO2.
Para obtener más información acerca de nuestros productos y embalajes ecológicos, visite el sitio www.dlinkgreen.com.
57D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
ITALIANO IT
La presenza di questo simbolo sul prodotto o sulla confezione del prodotto indica che, in conformità alle leggi e alle normative locali,
questo prodotto non deve essere smaltito nei riuti domestici, ma avviato al riciclo. Una volta terminato il ciclo di vita utile, portare il
prodotto presso un punto di raccolta indicato dalle autorità locali. Alcuni questi punti di raccolta accettano gratuitamente i prodotti
da riciclare. Scegliendo di riciclare il prodotto e il relativo imballaggio, si contribuirà a preservare l'ambiente e a salvaguardare la
salute umana.
D-Link e l'ambiente
D-Link cerca da sempre di ridurre l'impatto ambientale dei propri stabilimenti e dei propri prodotti. Allo scopo di ridurre al minimo tale impatto,
D-Link progetta e realizza i propri prodotti in modo che rispettino il più possibile l'ambiente, utilizzando materiali riciclabili a basso tasso di
tossicità sia per i prodotti che per gli imballaggi.
D-Link raccomanda di spegnere sempre i prodotti D-Link o di scollegarne la spina quando non vengono utilizzati. In questo modo si contribuirà
a risparmiare energia e a ridurre le emissioni di anidride carbonica.
Per ulteriori informazioni sui prodotti e sugli imballaggi D-Link a ridotto impatto ambientale, visitate il sito all'indirizzo www.dlinkgreen.com.
NEDERLANDS NL
Dit symbool op het product of de verpakking betekent dat dit product volgens de plaatselijke wetgeving niet mag worden
weggegooid met het huishoudelijk afval, maar voor recyclage moeten worden ingeleverd. Zodra het product het einde van de
levensduur heeft bereikt, dient u het naar een inzamelpunt te brengen dat hiertoe werd aangeduid door uw plaatselijke autoriteiten,
sommige autoriteiten accepteren producten zonder dat u hiervoor dient te betalen. Door het product en de verpakking op deze
manier te recyclen helpt u het milieu en de gezondheid van de mens te beschermen.
D-Link en het milieu
Bij D-Link spannen we ons in om de impact van onze handelingen en producten op het milieu te beperken. Om deze impact te beperken,
ontwerpt en bouwt D-Link zijn producten zo milieuvriendelijk mogelijk, door het gebruik van recycleerbare producten met lage toxiciteit in
product en verpakking.
D-Link raadt aan om steeds uw D-Link producten uit te schakelen of uit de stekker te halen wanneer u ze niet gebruikt. Door dit te doen bespaart
u energie en beperkt u de CO2-emissies.
Breng een bezoek aan www.dlinkgreen.com voor meer informatie over onze milieuverantwoorde producten en verpakkingen.
58D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
POLSKI PL
Ten symbol umieszczony na produkcie lub opakowaniu oznacza, że zgodnie z miejscowym prawem i lokalnymi przepisami
niniejszego produktu nie wolno wyrzucać jak odpady czy śmieci z gospodarstwa domowego, lecz należy go poddać procesowi
recyklingu. Po zakończeniu użytkowania produktu, niektóre odpowiednie do tego celu podmioty przyjmą takie produkty
nieodpłatnie, dlatego prosimy dostarczyć go do punktu zbiórki wskazanego przez lokalne władze. Poprzez proces recyklingu i
dzięki takiemu postępowaniu z produktem oraz jego opakowaniem, pomogą Państwo chronić środowisko naturalne i dbać o
ludzkie zdrowie.
D-Link i środowisko
D-Link podchodzimy w sposób świadomy do ochrony otoczenia oraz jesteśmy zaangażowani w zmniejszanie wpływu naszych działań i produktów
na środowisko naturalne. W celu zminimalizowania takiego wpływu rma D-Link konstruuje i wytwarza swoje produkty w taki sposób, aby były
one jak najbardziej przyjazne środowisku, stosując do tych celów materiały nadające się do powtórnego wykorzystania, charakteryzujące się
małą toksycznością zarówno w przypadku samych produktów jak i opakowań.
Firma D-Link zaleca, aby Państwo zawsze prawidłowo wyłączali z użytku swoje produkty D-Link, gdy nie są one wykorzystywane. Postępując w
ten sposób pozwalają Państwo oszczędzać energię i zmniejszać emisje CO2.
Aby dowiedzieć się więcej na temat produktów i opakowań mających wpływ na środowisko prosimy zapoznać się ze stroną Internetową www.
dlinkgreen.com.
ČESKY CZ
Tento symbol na výrobku nebo jeho obalu znamená, že podle místně platných předpisů se výrobek nesmí vyhazovat do komunálního
odpadu, ale odeslat k recyklaci. Až výrobek doslouží, odneste jej prosím na sběrné místo určené místními úřady k tomuto účelu.
Některá sběrná místa přijímají výrobky zdarma. Recyklací výrobku i obalu pomáháte chránit životní prostředí i lidské zdraví.
D-Link a životní prostředí
Ve společnosti D-Link jsme si vědomi vlivu našich provozů a výrobků na životní prostředí a snažíme se o minimalizaci těchto vlivů. Proto své
výrobky navrhujeme a vyrábíme tak, aby byly co nejekologičtější, a ve výrobcích i obalech používáme recyklovatelné a nízkotoxické materiály.
Společnost D-Link doporučuje, abyste své výrobky značky D-Link vypnuli nebo vytáhli ze zásuvky vždy, když je nepoužíváte. Pomůžete tak šetřit
energii a snížit emise CO2.
Více informací o našich ekologických výrobcích a obalech najdete na adrese www.dlinkgreen.com.
59D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
MAGYAR HU
Ez a szimbólum a terméken vagy a csomagoláson azt jelenti, hogy a helyi törvényeknek és szabályoknak megfelelően ez a termék
nem semmisíthető meg a háztartási hulladékkal együtt, hanem újrahasznosításra kell küldeni. Kérjük, hogy a termék élettartamának
elteltét követően vigye azt a helyi hatóság által kijelölt gyűjtőhelyre. A termékek egyes helyeken ingyen elhelyezhetők. A termék és
a csomagolás újrahasznosításával segíti védeni a környezetet és az emberek egészségét.
A D-Link és a környezet
A D-Linknél megértjük és elkötelezettek vagyunk a műveleteink és termékeink környezetre gyakorolt hatásainak csökkentésére. Az ezen
hatás csökkentése érdekében a D-Link a lehető leginkább környezetbarát termékeket tervez és gyárt azáltal, hogy újrahasznosítható, alacsony
károsanyag-tartalmú termékeket gyárt és csomagolásokat alkalmaz.
A D-Link azt javasolja, hogy mindig kapcsolja ki vagy húzza ki a D-Link termékeket a tápforrásból, ha nem használja azokat. Ezzel segít az energia
megtakarításában és a széndioxid kibocsátásának csökkentésében.
Környezetbarát termékeinkről és csomagolásainkról további információkat a www.dlinkgreen.com weboldalon tudhat meg.
NORSK NO
Dette symbolet på produktet eller forpakningen betyr at dette produktet ifølge lokale lover og forskrifter ikke skal kastes sammen
med husholdningsavfall, men leveres inn til gjenvinning. Vennligst ta det til et innsamlingssted anvist av lokale myndigheter når
det er kommet til slutten av levetiden. Noen steder aksepteres produkter uten avgift. Ved på denne måten å gjenvinne produktet
og forpakningen hjelper du å verne miljøet og beskytte folks helse.
D-Link og miljøet
Hos D-Link forstår vi oss på og er forpliktet til å minske innvirkningen som vår drift og våre produkter kan ha på miljøet. For å minimalisere denne
innvirkningen designer og lager D-Link produkter som er så miljøvennlig som mulig, ved å bruke resirkulerbare, lav-toksiske materialer både i
produktene og forpakningen.
D-Link anbefaler at du alltid slår av eller frakobler D-Link-produkter når de ikke er i bruk. Ved å gjøre dette hjelper du å spare energi og å redusere
CO2-utslipp.
For mer informasjon angående våre miljøansvarlige produkter og forpakninger kan du gå til www.dlinkgreen.com.
60D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
DANSK DK
Dette symbol på produktet eller emballagen betyder, at dette produkt i henhold til lokale love og regler ikke må bortskaes som
husholdningsaald, mens skal sendes til genbrug. Indlever produktet til et indsamlingssted som angivet af de lokale myndigheder,
når det er nået til slutningen af dets levetid. I nogle tilfælde vil produktet blive modtaget gratis. Ved at indlevere produktet og dets
emballage til genbrug på denne måde bidrager du til at beskytte miljøet og den menneskelige sundhed.
D-Link og miljøet
Hos D-Link forstår vi og bestræber os på at reducere enhver indvirkning, som vores aktiviteter og produkter kan have på miljøet. For at minimere
denne indvirkning designer og producerer D-Link sine produkter, så de er så miljøvenlige som muligt, ved at bruge genanvendelige materialer
med lavt giftighedsniveau i både produkter og emballage.
D-Link anbefaler, at du altid slukker eller frakobler dine D-Link-produkter, når de ikke er i brug. Ved at gøre det bidrager du til at spare energi og
reducere CO2-udledningerne.
Du kan nde ere oplysninger om vores miljømæssigt ansvarlige produkter og emballage på www.dlinkgreen.com.
SUOMI FI
Tämä symboli tuotteen pakkauksessa tarkoittaa, että paikallisten lakien ja säännösten mukaisesti tätä tuotetta ei pidä hävittää
yleisen kotitalousjätteen seassa vaan se tulee toimittaa kierrätettäväksi. Kun tuote on elinkaarensa päässä, toimita se lähimpään
viranomaisten hyväksymään kierrätyspisteeseen. Kierrättämällä käytetyn tuotteen ja sen pakkauksen autat tukemaan sekä ympäristön
että ihmisten terveyttä ja hyvinvointia.
D-Link ja ympäristö
D-Link ymmärtää ympäristönsuojelun tärkeyden ja on sitoutunut vähentämään tuotteistaan ja niiden valmistuksesta ympäristölle mahdollisesti
aiheutuvia haittavaikutuksia. Nämä negatiiviset vaikutukset minimoidakseen D-Link suunnittelee ja valmistaa tuotteensa mahdollisimman
ympäristöystävällisiksi käyttämällä kierrätettäviä, alhaisia pitoisuuksia haitallisia aineita sisältäviä materiaaleja sekä tuotteissaan että niiden
pakkauksissa.
Suosittelemme, että irrotat D-Link-tuotteesi virtalähteestä tai sammutat ne aina, kun ne eivät ole käytössä. Toimimalla näin autat säästämään
energiaa ja vähentämään hiilidioksiidipäästöjä.
Lue lisää ympäristöystävällisistä D-Link-tuotteista ja pakkauksistamme osoitteesta www.dlinkgreen.com.
61D-Link DCS-2630L User Manual
Appendix B - Regulatory Information
SVENSKA SE
Den här symbolen på produkten eller förpackningen betyder att produkten enligt lokala lagar och föreskrifter inte skall kastas i
hushållssoporna utan i stället återvinnas. Ta den vid slutet av dess livslängd till en av din lokala myndighet utsedd uppsamlingsplats,
vissa accepterar produkter utan kostnad. Genom att på detta sätt återvinna produkten och förpackningen hjälper du till att bevara
miljön och skydda människors hälsa.
D-Link och miljön
På D-Link förstår vi och är fast beslutna att minska den påverkan våra verksamheter och produkter kan ha på miljön. För att minska denna påverkan
utformar och bygger D-Link sina produkter för att de ska vara så miljövänliga som möjligt, genom att använda återvinningsbara material med
låg gifthalt i både produkter och förpackningar.
D-Link rekommenderar att du alltid stänger av eller kopplar ur dina D-Link produkter när du inte använder dem. Genom att göra detta hjälper
du till att spara energi och minska utsläpp av koldioxid.
För mer information om våra miljöansvariga produkter och förpackningar www.dlinkgreen.com.
PORTUGUÊS PT
Este símbolo no produto ou embalagem signica que, de acordo com as leis e regulamentações locais, este produto não deverá ser
eliminado juntamente com o lixo doméstico mas enviado para a reciclagem. Transporte-o para um ponto de recolha designado pelas
suas autoridades locais quando este tiver atingido o m da sua vida útil, alguns destes pontos aceitam produtos gratuitamente. Ao
reciclar o produto e respectiva embalagem desta forma, ajuda a preservar o ambiente e protege a saúde humana.
A D-Link e o ambiente
Na D-Link compreendemos e comprometemo-nos com a redução do impacto que as nossas operações e produtos possam ter no ambiente.
Para minimizar este impacto a D-Link concebe e constrói os seus produtos para que estes sejam o mais inofensivos para o ambiente possível,
utilizando meteriais recicláveis e não tóxicos tanto nos produtos como nas embalagens.
A D-Link recomenda que desligue os seus produtos D-Link quando estes não se encontrarem em utilização. Com esta acção ajudará a poupar
energia e reduzir as emissões de CO2.
Para saber mais sobre os nossos produtos e embalagens responsáveis a nível ambiental visite www.dlinkgreen.com.
62D-Link DCS-2630L User Manual
Loading...