Danby DWM99W User Manual
OWNER’S MANUAL
MANUEL D'UTILISATION
Model • Modèle
DWM99W
CAUTION:
Read and follow all safety rules
and operating instructions
before first use of this product.
PRÉCAUTION:
Veuillez lire attentivement
les consignes de sécurité et les
instructions d'utilisation avant
l'utilisation initiale de
ce produit.
PRECAUCIÓN:
Lea y observe todas las reglas
de seguridad y las instrucciones de operación antes de
usar este producto por primera
vez.
Danby Products Limited, Guelph, Ontario Canada N1H 6Z9
Danby Products Inc., Findlay, Ohio USA 45840
DWM99W 11.00.
Top Load Washing Machine
Instructional Manual
Laveuse à chargement supérieur
Notice d’utilisation
Lavadora a cargamiento superior
Manual de instrucciones
R
R
1
TABLE OF CONTENTS
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Water Supply Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installing the Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installer Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Before Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
How to Use Your Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
General Washing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Special Care Washing Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
User Maintenance Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
INTRODUCTION
Thank you for buying a Danby appliance. Before operating this unit please read and save these instructions.
Model Number: ___________________________ Serial Number: ______________________________
Date of Purchase: _________________________ Place of Purchase: ____________________________
Dealer’s Name and Address: _______________________________________________________________
This information will be required if your unit requires servicing and/or for general inquiries. To contact a
Customer Service Representative, call Danby TOLL FREE.
1-800-26-Danby
CAREFULLY READ AND SAVE THESE INSTRUCTIONS
These instructions for use are intended for the user. They describe the appliance and correct installation and
operating procedures for safe use.
NOTE:
This appliance was carefully packed and thoroughly inspected before leaving our factory. Responsibility for
its safe delivery was assumed by the carrier upon acceptance of the shipment. Claims for loss or damage
sustained during transit must be made directly to the carrier.
2
SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
1. Please read this instruction manual carefully
before operating.
2. Refer to the Grounding Instructions
(under electrical requirements) in this
manual for the proper grounding of
the washer.
3. Do not wash articles that have been previously
cleaned in, washed in, soaked in or spotted
with gasoline, dry-cleaning solvents, other
flammable or explosive substances as they
give off vapors that could ignite or explode.
4. Do not allow children to play on or in the
washer. Close supervision of children is
necessary when the washer is used near
children.
5. Do not reach into the washer if the inner tub
or agitator is revolving.
6. Do not install or store the washer where it will
be exposed to water and/or weather.
7. Do not tamper with the controls.
8. Do not repair or replace any part of the washer,
or attempt any servicing unless specifically
recommended in the user maintenance
instructions trouble shooting guide that you
understand and have the skills to carry out.
9. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors
that could ignite or explode.
10. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not
been used for two weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot
water system has not been used for such a
period, before using this washer, turn on all hot
water faucets and let the water flow from each
for several minutes. This will release any
accumulated hydrogen gas. THIS GAS IS
FLAMMABLE, DO NOT SMOKE OR USE AN
OPEN FLAME DURING THIS TIME.
11. Replace worn power cords and/or loose plugs.
12. To reduce the risk of an electric shock or fire,
DO NOT use an extension cord or an adapter
to connect the washer to the electrical power
source.
13. Use your washer only for its intended purpose,
washing clothes.
14. ALWAYS disconnect the washer from electrical
supply before attempting any service.
Disconnect the power cord by grasping the
plug, not the cord.
15. Install the washer according to the
INST ALLATION INSTRUCTIONS. All
connections for water, drain, electrical power
and grounding must comply with local codes
and be made by licensed personnel when
required. Do not do it yourself unless you know
how!
16. To reduce the risk of fire, clothes which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner etc. or anything
containing wax or chemicals such as in mops
and cleaning cloths, must not be put into the
washer. These flammable substance may
cause the fabric to catch on fire.
17. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
18. Keep your washer in good condition. Bumping
or dropping the washer can damage safety
features. If this occurs, have your washer
checked by a qualified serviceman.
19. Be sure water connections have a shut-off
valve and fill hose connections are tight.
CLOSE the shut-off valves at the end of each
wash day.
20. The LID MUST BE CLOSED any time the
washer is to spin. DO NOT by-pass the safety
switch by permitting the washer to spin with the
lid open. Abrake will stop the inner tub within
seconds if the lid is opened during spinning. If
the inner tub does not stop when the lid is
opened, remove the washer from use and call
a serviceman.
3
SAFETY INSTRUCTIONS CONTINUED
21. Always follow the fabric care instructions
supplied by the garment manufacturer.
22. Never operate the washer with any guards
and/or panels removed.
23. DO NOT operate the washer with broken or
missing parts.
24. DO NOT by-pass any safety devices.
25. Failure to install, maintain, and/or operate this
machine according to these instructions may
result in conditions which can produce bodily
injury and/or property damage.
NOTE:
The WARNING AND IMPORTANT SAFETY
INSTRUCTIONS appearing in this manual are
not meant to cover all possible conditions and
situations that may occur. It must be understood
that common sense, caution and carefulness
are factors which CANNOT be built into the
washer. These factors MUST BE supplied by
the person(s) installing, maintaining, or
operating the washer.
Always contact your dealer, distributor, service
agent or the manufacturer about any problems or
conditions you do not understand.
INSTALLATION INSTRUCTIONS
BEFORE
YOU START
Tools
For most installations, the basic tools that you
will need are:
Electrical
The washer needs a 120 V~/60 Hz, polarized three
slot effectively grounded receptacle. For more
detailed information refer to the Section on
Electrical Requirements
Water
The washer needs standard 3/4 inch water supply
faucets with a pressure between 0.02 MPa and .08
MPa. For more detailed information refer to the
Water Supply Requirements
Specifications
1. Rated Voltage 120V~
2. Rated Frequency 60Hz
3. Rated Current 2.5A
4. Max Washing capacity
and Spin dry capacity 4.0 kg
5. Enter water pressure 0.02 MPa ~ 0.8 MPa
6. Net weight 36kg
7. Size(D X W X H) 545mm x 550mm x 890mm
Wrench
Pliers
Screwdriver
4
ELECTRICAL REQUIREMENTS
WARNING
To reduce the risk of electrical shock or personal
injury, all wiring and grounding MUST conform with
the latest edition of the National Electrical Code,
ANSI/NFPA 70, and such local regulations as might
apply. IT’S THE CONSUMERS RESPONSIBILITY
TO HAVE THE WIRING FUSES AND CIRCUIT
BREAKERS CHECKED BY A QUALIFIED ELECTRICIAN TO MAKE SURE YOUR HOME HAS
ADEQUATE ELECTRICAL POWER TO OPERATE
THE WASHER.
• DO NOT OVERLOAD THE WASHER
• DO NOT USE AN ADAPTER
• DO NOT USE AN EXTENSION CORD
Note:
Have a qualified electrician check the polarity of the
wall receptacle. If a voltage reading is measured
other than illustrated, a qualified electrician should
correct the problem.
GROUNDING INSTRUCTIONS
The washer must be grounded in the event of a
malfunction or breakdown, grounding will reduce the
risk of electrical shock by providing a path of least
resistance for electrical shock. The washer is
equipped with a cord having an equipment grounding conductor and a 3 prong grounding plug. The
plug must be plugged into an appropriate outlet that
is installed and grounded in accordance with all
local codes and ordinances.
Do not modify the plug provided with the washer, if
it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
If a positive ground cannot be established through
the power cord and if local code permits its use,
connect an external ground wire (18 gauge minimum, available at your local hardware store).
Connect one end of the wire under any screw
(located at rear of washer) and other end to a
known effective electrical ground.
STANDARD 120 VOLT, 60 HERTZ, 3-WIRE
EFFECTIVELY GROUNDED CIRCUIT
(120V~/ 60HZ WITH THE 3 PRONG GROUNDING PLUG)
5
WATER SUPPLY REQUIREMENTS
W
ARNING
Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used
for two weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period and before using the washer,
turn on all hot water faucets and let the water flow
from each for several minutes. This will release any
accumulated hydrogen gas.
THIS GAS IS FLAMMABLE, DO NOT SMOKE OR
USE AN OPEN FLAME DURING THIS TIME.
Water supply faucets must fit standard 3/4 inch
(19.05mm) female garden hose couplings.
DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS.
NOTE:
Water supply faucets should be readily accessible
to permit turning them off when the washer is not
being used.
W
ATER TEMPERATURE
Cold
Recommended cold water temperature is 50 ~ 750F,
10 ~ 23.8
0
C
Hot
Recommended hot water temperature is 135 ~
145
0
F, 57 ~ 62.70C
Warm
Mixture of hot and cold water. (Warm water temperature is dependent upon the water temperature and
the pressure of both the hot and cold water supply
lines.)
IMPORTANT: Owner should turn off water supply
whenever there will be an extended period of nonuse.
Water pressure
Do not operate the washer when the water pressure
is lower than 0.02 MPa or higher than .8 MPa. to
avoid damage of the inlet system.
Risers
Risers (or air cushions) may have to be installed if
the pipes knock or pound when flow of water stops.
The risers are more efficient when installed as close
as possible to the water supply faucets, see illustration below.
Cold Water
Connection
Hot Water
Connection
Water Mixing
Valve
Water Inlet
Hoses
Water Supply
Faucets
Water Supply
Faucets
Risers
(air cushions)
6
INSTALLING THE WASHER
STEP
1
Remove the shipping brace and insert the noise
proof plate on the washing machine.
The shipping brace should be saved and must
be used (to prevent damage to washer
components) whenever the washer is moved
or transported to a new location.
CAUTION:
• Do not put you hands into rotating tub
• Do not sprinkle water over the control panel
• Do not leave wet clothes on the control panel
• The safety switch will stop the spinning
operation automatically if the laundry load is
unevenly distributed (balanced) in the tub. Open
the lid and redistribute the laundry evenly, then
close the lid to restart.
• After use, turn off the water supply lines
Shipping
Brace
Take the noise proof
plate out of the
package.
The opening of the
noise proof plate is at
the bottom of the
machine.
Insert the noise proof
plate into the washing
machine base.
Lay down the
machine and secure
the noise proof plate
by fastening the two
screws
Opening
7
STEP 2
Single Hose Installation
(portable applications)
Your washing machine is equipped with easy to
install accessories allowing the washing machine to
be connected to a single source water supply line;
Accessories Included:
2 only Inlet Hose Fig. A
1 only Water Inlet Hose "Quick Connect". Fig. B
1 only Faucet Adapter. Fig. C
1 only Water Inlet Valve Cap/Plug. Fig. D
Important Notice: For portable installations (using
a single inlet hose only) it will be necessary to
"cap/plug" one side of the hot/cold water valve not
being used. Fig. D
Failure to install the "cap/plug" on the open side
of the water valve will result in leakage from the
valve during any/all water fill cycles.
Special Note: Depending on which side of the
(Hot/Cold) valve the cap/plug is installed, certain
"WASH/TEMP" fill programs will not be operational.
i.e.
• If you cap/plug the HOT WATER (upper) valve, it
will not be possible to select the "COLD/COLD"
WASH/TEMP water fill program. You can only
select either the WARM/COLD or HOT/COLD
WASH/TEMP water fill programs. (under the
COLD/COLD setting no water will enter the wash
tub)
• If you cap/plug the COLD WATER (lower) valve, it
will not be possible to select the "HOT/COLD"
WASH TEMP water fill program. You can only
select either the WARM/COLD or COLD/COLD
WASH/TEMP water fill program. (under the
HOT/COLD setting no water will enter the wash
tub)
Connecting the Water Inlet Hose:
• Screw the faucet adapter onto the faucet. Fig. C
(check for leaks, use Teflon tape to eliminate if
necessary)
• Install rubber washer into each end of the fill
hose. Fig. E
Inlet Hose
Connector
2PCS
1PC
Hot Water
Connector
Cold Water
Connector
A
B
C
D
Hot Water
Connector
Cold Water
Connector
D
Water
Inlet Hose
Cap/Plug
Rubber Ring
Water
Inlet Hose
E
C
Connecting
Nut
8
• Connect fill hose (with 900elbow) to either the
HOT/COLD water inlet valve located at the back
of the washing machine, tighten moderately.
(remember to install the “cap/plug” on the inlet
valve not being used)
• Connect the opposite end of the hose directly to
the body of the quick connect. Fig. F
• Attach the quick connect directly to the faucet
adapter, by pulling the outer collar (ring)
downward while pushing the quick connect
upward onto the faucet. Release the outer collar
(ring) and the quick connect will lock into place.
Fig. H
• Slowly open the water supply line and check for
any sign of leaks at all water connection points.
• If leaks occur, immediately close the water supply
and effect the necessary repairs and/or replace
ment of any/all defective connections. If you are
unable to effect suitable repairs yourself, call our
toll free CUSTOMER HELP LINE at
"1 800 26 DANBY and ask for assistance.
NOTE: Once the water supply line to the machine
is open, the inlet hose is pressurized. (even when
the water supply is closed immediately thereafter)
NOTE: Failure to relieve (release) hose pressure
before attempting to disconnect the hose from the
faucet can result in back pressure over-spray.
WARNING: Incoming water temperature can be
very hot and back pressure over-spray can cause
severe burns and/or scalding.
NOTE: To relieve (release) hose pressure, close
the water faucet. Press and "Hold" the "red"
(pressure relief) button located on the front (body)
of the quick connect until the flow of water stops.
Fig. F
When the flow of water has stopped, the hose
pressure is released and it is now safe to
disconnect the hose from the faucet adapter.
Permanent Hose Installation
(dual hose)
If your washing machine is to be permanently
installed both fill hoses are required. The following
accessories are not required for permanent
installation applications;
•Water Inlet Hose Quick Connect.
• Faucet Adapter.
• Water Inlet Valve Cap/Plug.
We recommend that you store these items in a safe
place for future use, in the event there is ever a
need to change your installation method.
Connecting the Water Inlet Hoses:
• Install a rubber washer into each end of both fill
hoses.
• Connect the both fill hoses (with the 90º elbow)
respectively to both the HOT & COLD water
valves located at the back of the washing machine
and tighten moderately. Fig. G
Rubber Ring
Connecting
Nut
F
Water
Inlet Hose
Outer
Collar
Pressure
Relief Button
Cold Water
Connection
Hot Water
Connection
Water Mixing
Valve
Water Inlet
Hoses
Water Supply
Faucets
G
H
Outer
Collar
9
• Connect the opposite end of the fill hoses to their
respective HOT & COLD water supply lines. Fig. I
IMPORTANT: Make sure the HOT water line is
connected to the HOT (upper) water valve and the
COLD water line is connected to the COLD
(lower) water valve. Fig. I
• Slowly open both water supply lines and check for
any sign of leaks at all connection points.
• If leaks occur, immediately close the water supply
lines and effect the necessary repairs and/or
replacement of any/all defective connections.
• If you are unable to effect suitable repairs
yourself, call our toll free CUSTOMER HELP LINE
at "1 800 26 DANBY and ask for assistance.
STEP 3
Connect Drain Hose to Drain
Receptacle
Portable Installation: Hang the drain pipe over the
edge of the wash tub and/or kitchen sink. Make
sure the hose cannot be accidentally displaced
when the drain water is being discharged.
Permanent Installation: Insert the end of the drain
hose directly into the drain stem pipe and /or hang
over the edge of the wash tub.
NOTE: The highest
point of the drain
hose must be
positioned between
26" ~ 46" above
floor level, otherwise
the pumping out
(efficiency) of the
water may be
affected. Fig. J
STEP 4
Levelling the Washing Machine.
To prevent vibration and unnecessary movement
during wash and spin operation, the washer must
be installed on a firm and level surface, This is
accomplished by using the level adjustment knob
located on the lower right side of the cabinet. To
change the height of the adjustment leg, unscrew
the level adjustment knob, set the machine level
and re-tighten when the machine is stable. Fig. M
The inclination angle of the washer shall not be
more than two (2º) degrees.Place the washer at
least 5cm (2") away from the wall.
Portable Installations: For portable applications,
the washing machine comes equipped with four (4)
"north/south" casters that can easily be installed to
assist in the movement of the machine too and from
the sink. Lay the unit on its back.
Install the casters into the bottom of the base as
depicted. Fig. N
Return the machine to the upright position.
When the machine is positioned for operation, set
the height of the adjustment leg slightly higher than
the front caster to prevent movement of the
machine during wash and spin operation.
NOTE: Not all movement will be totally eliminated,
this is normal.
Tap
Connector
Connecting
Nut
I
Water
Inlet Hose
J
Correct
Level
Adjustment Knob
M
Loosen
Tighten
Incorrect
N
Adjustable Foot
Castor
Castor
Fixed FootFixed Foot
Castor
Castor
Fixed foot
10
STEP 5
Plug In the Washing Machine.
Refer to section on Electrical Requirements before
connecting the washer. Fig. O
O
STEP 6
Wipe Out the Inside of the Washer
Prior to Being Used.
Review Use and Care Guide. Fig. P
P
STEP 7
Check the Safety Switch.
The washer should stop spinning when the lid is
opened. Fig. Q
Q
INSTALLER CHECKLIST
❏ Remove the shipping brace
❏ Connect the water inlet hoses
❏ Connect the hose to drain receptacle
❏ Install on a firm and level surface
❏ Plug in the washer
❏ Wipe out the inside of washer, review use and care guide
❏ Check safety switch
FAST TRACK FOR INSTALLING THE WASHER
(refer to manual for more detailed information)
11
12
PARTS IDENTIFICATION
Control Panel
Hand Wash Corner
Softener Dispenser
Bleach Dispenser
Inner Tub
Base
Noise Proof Plate
Adjustable Foot
Level Adjustable Knob
Drain Hose
Power Cord
Agitator
Drain Hose
Hook
Lid
Inlet Hose
13
CONTROL PANEL
Water Level
Control
Temperature
Control
Wash Control Program
Control
BEFORE WASHING
PREPARE W
ASH LOAD
Load articles by the weight not more that 4 kg. Mix
large and small articles in a load to get the best
washing results.
Drop articles loosely into the inner tub. Do not pack
them in or wrap them around the agitator.
Articles should move freely through the wash water
for best cleaning results. Articles should rollover
sink and then reappear.
When washing very large articles, do not fill inner
tub as full as other loads.
The water level in your washer should fit the size of
your wash load. Small loads will use lower water
levels. There must be enough water in the inner tub
to allow articles to move and turn over freely.
Overloading the inner tub can result in poor
washing and rinsing. Overloading may also cause
wrinkling and tearing of articles.
Water Level
Right
Wrong
14
W
ASH TEMPERATURE
Hot Water
Hot water will give the best results of cleaning and
sanitizing. But it is not suitable for all articles. It is
best for sturdy whites and colourfast articles, heavily
soiled articles and diapers.
Warm Water
By using warm water, there is less chance of colour
loss in articles. Use with light and moderate soils,
non-colourfast or dark colours, permanent press,
silks, woolens, nylons and acrylic.
Cold Water
Cold water is less effective in cleaning than hot or
warm water, but it does minimize wrinkling and
colour fading. Use it for washing extra sensitive
clothes and for the rinsing of all fabrics.
Energy
You can save energy when washing by following a
few guidelines:
1. Heating water accounts for the greatest
expense when washing. Save on heating water
by using cold rinses.
2. Wash full loads, but do not overload.
3. Select a shorter wash time for lightly soiled
articles.
A.) Determine proper cycle
• Press down the program knob and turn it to the
desired function.
• Pull up the program knob to start the wash
program.
WARNING:
The program knob can only be turned clockwise
when it is pressed down.
B.) To Wash clothes
IMPORTANT:
Before using your new washer, make sure the
washer cord is plugged into a properly grounded
and polarized outlet which has the appropriate voltage (refer to the serial plate). Make sure the washer
hoses are connected to the hot and cold water
faucets, and that the faucets are turned on. Be sure
the drain hose is not kinked and is inserted into a
drain. See the INSTALLATION INSTRUCTIONS for
details of proper washer installation.
Before using the washer for the first time, wipe out
the inside of the washtub with a sudsy cloth.
1. Load laundry and add detergent (refer to
section “GENERAL WASHING INFORMATION”
for proper detergent usage.
2. Water level, Select water level according to
laundry quantity. Refill function allows you to
add water during operation (turn the water
level knob to RESET and hold for 2-3 seconds.
Then turn to the level desired).
3. Wash Choice,
regular mode, press down the WASH CHOICE
button. Gentle mode, release the button.
4. Close the lid
The washer will not spin with the lid open.
5. Set WASH/RINSE temperatures
NOTE: If your washer is (permanently installed
connected to both a HOT/COLD water supply,
the washer will provide a cold rinse in all
temperature settings. If your washer is installed
under a portable application, connected to a
single water supply, the wash and rinse
temperatures will be the same. Also refer to
the “special note” under portable (single
hose) installation.
C.) Timer
Although the washer cycles are automatic, the timer
may be reset to lengthen, shorten or repeat a portion of the cycle.
To set or reset the timer, push timer knob in to stop
the washer. Hold timer knob firmly while turning
clockwise to the setting desired. Pull timer knob out
to start the washer.
HOW TO USE YOUR WASHER
Cycles
Recommended Detergent
Amount
15
ECONOMY CYCLE
REGULAR CYCLE
HOW TO USE YOUR WASHER CONTINUED
Bleach
Do not pour bleach directly over the clothes.
Pour the bleach into the bleach dispenser.
Wash the inner tub with clean water after using
bleach
Hand Wash Corner
Use this hand wash corner to wash heavily soiled
spots.
Preparations Before Wash
Remove clothes that cannot be machine washed.
Separate greased items from non-greased items,
separate dark from light colours
Empty pockets and remove all things attached to
the laundry, especially small metal objects.
Maximum Capacity
The maximum washing capacity and spin capacity
is 4 kg
If the agitator cannot rotate, reduce 1 or 2 laundry
articles.
Spin Only Program
Close the lid
Turn the program knob to the starting point of the
last spin function and pull out the knob to begin.
GENERAL WASHING INFORMATION
Water Refill
Wash 12-15 min.
Drain 2.3 min.
Spin 2.7 min.
Water Refill
Rinse 2 min.
Drain 2.3 min.
Spin 2.7 min.
Water Refill
Rinse 2 min.
Last Rinse 2 min.
Drain 2.8 min.
Spin 4.2 min.
Water Refill
Wash 7 min.
Drain 2.3 min.
Spin 2.7 min.
Water Refill
Rinse 2 min.
Last Rinse 2 min.
Drain 2.8 min.
Spin 4.2 min.
Low 1 10 - 16g 20 - 32g
Low 2 12 - 19g 24 - 38g
Mid 14 - 22g 27 - 43g
High 18 - 24g 35 - 47g
Detergent Amount
Lightly
Soiled
Water
Level
Heavily
Soiled
16
SPECIAL CARE WASHING INFORMATION
Knits
A variety of knits are being used for many types of
clothing and household furnishings. Many knits are
machine washable, some are hand washable and
some must be dry-cleaned. When buying, make
sure the garment has a care label with care
instructions. These directions must be followed
otherwise they may shrink or relax when exposed
to water.
Rayon Knits
Rayon stretches and shrinks easily. Treat as a delicate fabric and wash gently.
Cotton Knits
Unless the label indicates that it is preshrunk, cotton
knits will probably shrink to some degree. Over drying contributes to shrinkage of cotton knits.
Wash water should be hot or warm suitable for
colour and soil. The rinse water should be cold.
Synthetic Knits
Knits made from synthetic fibers or blends containing a high percentage of synthetics will generally
keep their shape. When buying, make sure the trimmings (including belts) are machine washable,
seams are not frayed, and zippers and trimmings
are well fastened.
Wool Sweaters
Loosely knit or delicately constructed sweaters will
need delicate care hand wash. Rinse thoroughly.
Block to shape and dry flat.
For sweaters labeled “machine washable” follow
manufacturers directions. Dry flat. Excess agitation
and excess tumbling are the main cause of wool
shrinkage.
Wool Knits
Dry-clean wool knits unless labeled “machine washable” follow manufacturers directions.
USER MAINTENANCE INSTRUCTION
Cold Weather
If the washer is delivered on a cold day (below
freezing), or is stored in an unheated room or area
during the cold months, do not attempt to operate it
until the washer has had a chance to warm up.
Care of Your Washer
• Use only a damp or sudsy cloth for cleaning the
control panel. Some spray prewash products may
harm the finish on the control panel.
•Wipe the washer cabinet as needed. If detergent,
bleach or other washing products are spilled on
the cabinet, wipe immediately. Some products will
cause permanent damage if spilled on the cabinet.
• Do not use scouring pads or abrasive cleaners.
• Do not lay sharp or rough objects on or against
the washer. The finish could be damaged.
• Do not expose the washer to direct sunlight or
rain.
• Keep the washer away from fire or heat source.
• The washtub will need no particular care though it
may need rinsing or wiping after an unusual load
has been washed. This also may be necessary if
too little detergent has been used.
• Leave the lid and open to allow the inside of the
washer to dry out after use. This helps prevent
musty odors from developing.
•When unplugging the power cord, do not pull the
wire cord, grasp the “plug” firmly and pull.
Motor Overload Protector
The internal overload protector in the motor will stop
the motor automatically in the event of an
overload. The overload protector will reset itself in
two or three minutes and the motor will reset
automatically. If the overload protector stops the
motor again, remove the washer from use and call
the serviceman to correct the problem.
Loading...