XLS 602
X L S S E R I E S
Architectural & Engineering Specifications
XLS 602 (120 V, 60 Hz models)
The power amplifier shall be a solid-state two-channel model.
The amplifer shall provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and special thermal protection for the unit’s transformers.
The front-panel controls shall be two black detented level controls (one for each channel), a power switch, and a circuit breaker for overload protection.
Front-mounted indicators shall be Clip: one red LED per channel which illuminates when the channel’s output signal is being overdriven, Power: one green LED which indicates that the amplifier has been turned on and AC power is available, and Fault: one yellow LED which illuminates when amplifier is in protect mode and briefly during normal power-up when amplifier is first switched on.
The recommended load impedance shall be 2 to 8 ohms per channel in Stereo and 8 ohms in Bridge Mono. The amplifier shall be safe when driving any kind of load, including highly reactive ones.
The rear-mounted output connectors shall be two 4-pole Speakon® connectors (one per channel) and a pair of 5-way binding posts per channel. Rear-mounted input connectors shall be 3-pin balanced XLR connectors.
The power amplifier shall meet or exceed the following performance criteria: Input sensitivity for rated output at 4 ohms: 1.26 V. Rated output with both channels driven with 0.15% THD (at 1 kHz) in Dual mode: 840 watts per channel into 2 ohms, 600 watts per channel into 4 ohms, and 370 watts per channel into 8 ohms. Rated output with 0.5% THD (at 1 kHz) in Bridge-Mono mode: 1,200 watts into 8 ohms and 1,680 watts into 4 ohms. Frequency Response at 1 watt, 20 Hz to 20 kHz: ±0.75 dB. Phase Response at 1 watt: –10 degrees at 10 Hz, +19 degrees at 20 kHz. Signal to Noise Ratio below rated power (20 Hz to 20 kHz): greater than 100 dB A-weighted. Total Harmonic Distortion at full rated power from 20 Hz to 1 kHz: less than 0.15%. Intermodulation Distortion (60 Hz and 7 kHz at 4:1, from full rated output to –40 dB): less than 0.3%. Damping Factor (8 ohms): greater than 200 from 10 to 400
Hz. Crosstalk (below rated power, –82 dB at 1 kHz, –58 dB at 20 kHz. Voltage Gain at maximum output: 31 dB. Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced. AC Line Voltages and Frequencies Available (±10%): 120 VAC/60Hz and 230 VAC/50 Hz.
The amplifier chassis shall be constructed of steel with a durable black finish and shall be designed for flow-through ventilation from the front panel to the back panel. Internal heat sinks with forced-air cooling shall provide rapid, uniform heat dissipation.
The dimensions of the amplifier shall allow for 19 inch (48.3 cm) EIA standard (RS- 310-B) rack mounting. The amplifier shall be 3.5 inches (8.9 cm) tall, and 14 inches (35.6 cm) deep behind the rack-mounting surface.
The amplifier shall weigh 27.2 pounds (12.3 kg).
The amplifier shall be designated the Crown XLS 602.
Crown International
P.O. Box 1000
Elkhart, IN 46515-1000
TEL: 574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
Specifications subject to change without prior notice. Latest information available at www.crownaudio.com.
Crown and Crown Audio are registered trademark of Crown International. Other trademarks are the property of their respective owners.
Printed in U.S.A.
03/04 |
135169-2A |
|
|
|
|
Loading...