OPERATOR’S MANUAL
R
5-drawer bb Chest model # 31018
service parts
Call 1-800-4MY-HOME or (1-800-469-4663) for Service Parts. Refer to Service Parts Drawing for full listing of Service Parts.
Locating Model # Information
Model numbers and other information required for service parts is located on a label on the interior right side of the top most drawer.
capacities
•The maximum weight for each drawer should be no more than 25 pounds.
•Empty weight of the unit is 37 lbs
•The maximum product weight, including contents, should be no more than 125 pounds.
maintenance
•For casters, use high quality bearing grease, (yearly).
•Lubricate the slides with grease or equivalent,(twice yearly.)
• Lubricate lock with graphite, (yearly).
Ball bearing slides |
Friction slides |
•Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild detergent and water.
•Auto wax will preserve the unit’s luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratches.
•Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid.
•If drawer liners are supplied, it is recommended they are used to protect the finish inside the drawers and to make the drawers easier to clean. The drawer liners may be cleaned with soap and water.
|
safety |
DANGER |
is used to indicate a hazardous situation which, |
if not avoided, will result in serious injury or death. |
|
WARNING |
indicates a hazardous situation which, if not |
avoided, could result in serious injury or death.
Cautionis used to indicate a hazardous situation which, if not avoided, may result in minor injury, moderate injury, or property damage.
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
danger
•DO NOT stand on this product. You may fall or cause product to tip.
•DO NOT open more than one drawer. The product may become unstable and tip.
•DO NOT step in the drawers. You may fall or cause product to tip.
•DO NOT mount this product on a truck bed or any other moving object.
•DO NOT move the product prior to closing and locking all the drawers. The drawers could come open and make the product unstable and tip.
warning
•WEAR SAFETY GLASSES when removing or repositioning the slides.
•DO NOT pull this product when moving it. Push the product to prevent personal injury.
•USE THE BRAKES when not moving this product. This will prevent the product from rolling.
•DO NOT alter this product in any manner. For example, do not weld external lockbars or attach electrical equipment.
•Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an uneven surface.
•BE CAREFUL when closing the cover. Remove hands before the cover closes completely.
caution
•This product is not designed to be directly lifted with a fork lift, or to be towed with any mechanical devices.
•The maximum weight for each drawer should never be exceeded.
•Only transport this product empty. Properly secure when transporting.
•DO NOT exceed maximum product weight, including contents. See Operations Sections: Capacities for more information.
Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 |
F1819 |
hardware
Tools Required:
3/8 inch wrench 5/16-inch drill bit
Hardware Included:
1/4 - 20 x 5/8" (Qty: 4)
1/4 - 20 Nut (Qty: 4)
Carton Contents
Chest:
Hardware bag
Literature
ASSEMBLY
to attach chest Process:
·Remove enough drawers to access the top and bottom mounting surfaces of the units. Refer to drawer removal instructions.
·Place the chest in the desired location on top of the cabinet or intermediate chest and mark the mounting hole locations onto the cabinet top.
·Remove the chest and drill two 5/16" (8mm) holes through the top of the cabinet or intermediate chest.
·Secure the units together using two 1/4 - 20 x 5/8" screws and nuts at each joint. The hardware is provided in the bag located in the top tray of the chest.
operation
Note: Not all operation instructions will relate to your model.
to lock chest Process:
▪Make sure drawers are fully closed.
▪Insert the lockbar (which stores in the top tray), tabbed end up, into the slot in the top tray and down into the slot in the base.
▪Close the cover and lock with the key.
to unlock chest
• Reverse above procedure..
REMOVING DRAWERS
•Empty the drawer.
•Fully extend the drawer.
Release
Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to remove.
2
Tab Style - Depress the release tabs on both sides, (this allows the slides to ride over the stops.)
Pull out to remove.
Friction Style - Fully extend the drawer. Insert screwdriver into the slot in the side and push in on the stop until it clears the lance. Pull drawer just past lance before releasing stop. Repeat the process for the other slide.
operation
INSTALLING drawers
Ball bearing slide - Pull slides and slide carrier out to fully extended position (see illustration.) Hold the slide on the cabinet while aligning it with the slide on drawer. Slightly insert one side and repeat for the other side. Slowly push drawer to its fully closed position to engage slide. Open drawer and reclose to ensure proper operation.
slide carrier
slide
REMOVING AND INSTALLING SLIDEs
•To remove the slide from the unit, first remove the drawer.
•After removing the drawers drill out the rivets, use a 5/32-in drill bit. The rivets will need to be replaced.
•To reinstall the slide, place the slide in the appropriate position in the unit and pull toward the front of the unit. Replace rivets to secure slide to the unit.
•For smooth operation, make sure the drawers are matched with their original slides.
Drill out rivet
3
Loading...