Bosch AQT 35-12, AQT 37-12, AQT 40-13 User Manual

OBJ_BUCH-1978-006.book Page 1 Monday, November 7, 2016 10:33 AM

Robert Bosch Power Tools GmbH

70538 Stuttgart

GERMANY

AQT

www.bosch-do-it.com

F 016 L81 447 (2016.05) AS / 70 ASIA	35-12 | 35-12+ | 37-13 | 37-13+ | 40-13

en Original instructions cn tw

ko

th

id Petunjuk-Petunjuk untuk Penggunaan Orisinal vi Bản gốc hướng dẫn sử dụng

OBJ_BUCH-1978-006.book Page 2 Monday, November 7, 2016 10:33 AM

2 |

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . Page 3
. . . . . . . . . . . . . . . . . . . .	. .	12
. . . . . . . . . . . . . . . . . . . .	. .	18
. . . . . . . . . . . . . . . . . . . . . . . .	25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Bahasa Indonesia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Halaman 40

Tiếng Việt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trang 49

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 3 Monday, November 7, 2016 10:33 AM

English

Safety Notes Explanation of symbols

General hazard safety alert.

Never direct the water jet

at people, animals, the unit

or electric components. Warning: High pressure jets can be dangerous if subject to misuse.

According to the applicable regulations, the appliance must never be used on the

drinking water network without a system separator. Use a separator as per IEC 61770 Type BA.

Water flowing though a system separator is considered not drinkable.

Safety Notes for pressure washer

Read all safety warnings and

all instructions. Failure to follow the warnings and instruc-

tions may result in electric shock, fire and/or serious injury.

The warning and information signs attached to the unit provide important information for safe operation.

Apart from the information in the operating instructions comply with the general safety regulations and regulations for the prevention of accidents.

English | 3

Connecting to the mains

The voltage indicated on the rating plate must correspond to the voltage of the power source.

We recommend that this equipment is only connected into a socket which is protected by a circuit-breaker that would be actuated by a 30 mA residual current.

Remove the plug from socket whenever the machine is left unattended for any period.

The electric supply installation should comply with IEC 60364-1.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

If the plug is damaged, pay attention to the following:

Plugs and sockets situated near the work site or outdoors should be to class IP 55 of BS 5490 to provide adequate protection against ingress of water, etc. and cable entries require effective sealing. Rubber shrouds should be provided over cable glands. Drip-proof (class IP X2 of

BS 5490) plugs and sockets to

BS 4343 are suitable for use indoors where the plug is away from the water spray area where the appliance is in use.

Never touch the mains plug with wet hands.

Do not pull plug while operating the device.

	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 4 Monday, November 7, 2016 10:33 AM

4 | English

Do not run over, crush or pull the power supply cord or extension cord, otherwise it may be damaged. Protect the cable from heat, oil and sharp edges.

Do not use the unit, if the power supply cord or important parts, e. g. high-pressure hose, power gun or safety devices are damaged.

Warning: Inadequate extension cords can be dangerous.

If an extension cord is used, the plug and socket must be of watertight construction. The extension cord must have a cross section in accordance with the operating instructions and be protected against splashed water. The connection must not be in water.

When replacing plugs on the power supply cable or extension lead the spray water guard and mechanical stability must remain intact.

Water connection

Comply with the regulations of your water supply company.

All connecting hoses must have properly sealed joints.

Make sure that the supply hose is at least 12.7 mm (1/2") in diameter and is reinforced.

The appliance should never be used on the drinking water supply without a back flow valve. Water which has passed the back flow valve is regarded as undrinkable.

The high-pressure hose must not be damaged (danger of bursting). A damaged high-pressure hose must be replaced immediately. Only use hos-

es and connections recommended by the manufacturer.

High-pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses, fittings and couplings recommended by the manufacturer.

Only clean or filtered water should be used for intake.

Application

Before use, check that the unit and operating equipment are in perfect condition and are safe to operate. Do not use the unit if it is not in perfect condition.

Do not direct the jet against yourself or others in order to clean clothes or footwear.

Do not use solvent-containing liquids, undiluted acids, acetone or solvents! This includes petrol, paint thinners, heating oil. The sprayed vapour is highly flammable, explosive and toxic.

The appropriate safety regulations must be observed when using the unit in dangerous areas (e. g. petrol stations). It is forbidden to operate the unit in potentially explosive locations.

The unit must be placed on a solid base.

Only use detergents recommended by the manufacturer. Comply with the application, disposal and warning instructions of the detergent manufacturers.

All current-conducting components in the working area must be protected against splashed water.

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 5 Monday, November 7, 2016 10:33 AM

The gun trigger must not be jammed in position “ON” during operation.

Wear suitable protective clothing to protect against splashing from some parts. Do not use the appliance within the range of persons unless they also wear protective clothing.

If necessary wear personal protective equipment (PPE) e. g. safety goggles, breathing protection etc to protect against water, particles and/or aerosols sprayed back from parts.

High pressure may cause objects to rebound. If necessary wear suitable personnel protective equipment such as safety goggles.

Vehicle tyres/tyre valves may only be cleaned from a minimum distance of 30 cm, otherwise the vehicle tyre/ tyre valve could be damaged by the high-pressure jet. The first indication of this is a discoloration of the tyre. Damaged vehicle tyres/tyre valves can be extremely dangerous.

Materials containing asbestos and other materials which contain substances which are hazardous to your health must not be sprayed.

Detergents must not be used undiluted. The products are safe to use as they contain no acids, alkalis or substances which are detrimental to the environment. We recommend that the detergents are kept out of the reach of children. If detergent comes into contact with the eyes, wash immediately with plenty of water and if swallowed contact a doctor immediately.

English | 5

Never use the pressure washer without the filter or with a dirty or damaged filter. Using the pressure washer without a filter or with a dirty or damaged filter may invalidate the warranty.

Metal parts may become hot after prolonged usage, if necessary wear protective gloves.

Avoid high pressure washing in bad weather conditions especially when there is a risk of lightning.

Operation

The operator must use the unit in accordance with the regulations. He/she must take local conditions into account and be aware of other people, especially children, when operating the unit.

The unit may only be used by authorised persons who have received training or have demonstrated their ability to operate the unit. The unit must not be operated by children or juveniles (danger of accidents due to incorrect use of the unit). Children should be supervised to ensure that they do not play with the appliance.

This machine can be used by people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the machine in a safe way and understand the hazards involved.

The unit must never be left unsupervised while the unit is switched on.

	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 6 Monday, November 7, 2016 10:33 AM

6 | English

The water jet from the high-pressure nozzle produces a recoil on the gun. You should therefore hold the gun and spray lance firmly with both hands.

Transport

Switch off the motor and secure the unit before transporting.

Maintenance

Switch off the unit prior to all cleaning and maintenance work and before replacing components. Pull out the mains plug if the unit is mains-operat- ed.

Repairs may only be carried out by authorised Bosch Service Centres.

Accessories and spare parts

Accessories and spare parts which have been approved by Bosch must be used. Original accessories and

Technical Data

spare parts guarantee that the unit can be operated safety and without any breakdowns.

Symbols

The following symbols are important for reading and understanding the operating instructions. Please take note of the symbols and their meaning. The correct interpretation of the symbols will help you to use the machine in a better and safer manner.

Symbol				Meaning
				Movement direction
				Weight
				On
				Off
Lo				Low pressure
Hi				High pressure
				Accessories

Intended Use

The product is intended for cleaning areas and objects outside the house, tools, vehicles and boats, if the appropriate accessories such as cleaning agents approved by Bosch are used.

Intended use is related to operation within 0 ° C and 40 ° C ambient temperature.

This product should not be used for professional use.

Pressure washer		AQT 35-12/		AQT 37-13/	AQT 40-13
		AQT 35-12+		AQT 37-13+
Article number		3 600 HA7 1..		3 600 HA7 2..	3 600 HA7 5..
Rated power	kW	1.5		1.7	1.9
Supply temperature max.	° C	40		40	40
Supply rate min.	l/min	5.8		6.2	6.6
Allowable pressure	MPa	12		13	13
Rated pressure	MPa	8		9	9
Rated Flow	l/min	5		5.5	6
Maximum inlet pressure	MPa	1		1	1
Autostop function					
Weight according to EPTA-Procedure 01:2014	kg	6.65/8.12		7.83/8.82	8.9
Protection class		/ II		/ II	/ II
Serial number		See serial number		(rating plate) on pressure washer.

The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.153 ohm.

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 7 Monday, November 7, 2016 10:33 AM

Mounting and Operation

Action	Figure	Page
Delivery Scope	1	58 – 59
Fold down handle operation	2	60
Connecting high pressure gun to lance	3	61
Connecting high pressure water supply
hose/nozzle	4	61
Attaching Nozzles	5	62 – 64
Connecting to the water supply	6	64
Switching On and Off	7	65
Adjust water jet	8	65
Connect detergent bottle	9	66
Clean the water filter	10	66
Clean nozzle	11	67
Gun storage	12	67
Gun/lance/nozzle is stored in action	13	68
Hose into the hose holder	14	68
Storage	15	68
Selecting Accessories	16	69

Starting

For Your Safety

Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled.

The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable). Only use approved extension cables. Contact your Bosch Service Centre for details.

If you want to use an extension cable when operating your high pressure washer, only the following cable dimensions should be used:

–1.5 mm2 – max length 20 m

–2.5 mm2 – max length 50 m

Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest Bosch Service Centre.

WARNING! Inadequate extension cables can be dangerous. Extension cable, plug and socket must be of watertight construction and intended for outdoor use.

Cable connections should be kept dry and off the ground.

For increased electrical safety to use a Residual Current Device (RCD) with a tripping current of not more than 30 mA. Always check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a Bosch Service Centre.

English | 7

For products not sold in GB:

WARNING: For your safety, it is required that the plug attached to the machine is connected with the extension cord. The coupling of the extension cord must be protected against splash water, be made of rubber or coated with rubber. The extension cord must be used with a cable strain relief.

Products sold in GB only: Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

To prevent damage to the appliance, do not allow it to operate dry.

Operation

Starting

Attach water supply hose (not supplied) to the mains water supply and machine.

Connect the product to the mains supply ensuring that the mains switch is in the off position.

Open water tap.

Press the safety lock (back button on the gun handle) to release the trigger. Fully press the trigger until there is a constant flow of water to clear the air from the machine and water supply hose. Release trigger. Press the safety lock (front button on the gun handle).

Turn button on main switch. Point the power gun downwards. Press the trigger safety lock to release the trigger. Fully press the trigger.

Autostop function

The machine is designed to switch off the motor when the trigger is released on the gun.

Working Advice

General

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the pressure washer by pulling the hose, this could cause the machine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure hose. Do not expose the high pressure hose to sharp edges or corners.

Never use a roto nozzle to clean motor vehicles.

WARNING! The Patio Cleaners supplied are only intended to be used on flat surfaces! Do not attempt to use them on steps or vertical surfaces. Never attempt to touch the rotating nozzle while operating the machine!

	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 8 Monday, November 7, 2016 10:33 AM

8 | English

Working advice for cleaning with detergents

Only use cleaning agents suitable specifically for high pressure washers.

We recommend that you use detergent sparingly for the sake of the environment. Observe the recommended dilution on the detergent label.

Recommended cleaning method

Step 1: Loosening dirt

Attach the High Pressure Foam nozzle or select the foam setting on the 3 in 1 nozzle and spray on the detergent sparingly.

Step 2: Removing dirt

Spray off the loosened dirt with the high-pressure spray.

Note: When cleaning a vertical surface spray off dirt/detergent from the bottom and work in an upwards direction. Rinse from the top and work downwards.

Use with alternative water sources

This high-pressure washer will self prime and can draw water from water tanks and natural water sources. It’s IMPORTANT that the water is clean and the BOSCH inlet filter is clear and fitted to the machine.

Troubleshooting

Open tanks/containers and natural water sources

Use the Self Priming accessory kit comprising:

–Inlet strainer with non return valve

–3 m reinforced supply hose

–Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m above the water level in the source in approximately 15 seconds.

Submerge the 3 m hose in water to displace the air. Connect the 3 m supply hose to the pressure washer ensuring that the inlet strainer remains submerged in the water source.

Run the pressure washer with the gun disconnected until a steady flow of water appears from the high pressure hose. Stop if this has this has not been achieved within 25 seconds and check all the connections. Switch off and connect the gun, lance and nozzle to operate.

It is important to ensure that all hose and coupling connections are of good quality, air tight and that all washers are in good condition and correctly seated in place. Failure to do so may affect the self priming performance.

Water Tanks with outlet connections

When connecting the pressure washer to a water tank with a suitable tap outlet, first connect the supply hose (not provided) to the tank outlet, open the tap to allow the water to displace all the air in the hose and then connect to the pressure washer.

		Problem		Possible Cause				Corrective Action
		Motor refuses to start		Plug not connected				Connect plug
				Mains socket faulty				Use another socket
				Fuse faulty / blown				Replace fuse
				Extension cable damaged				Try without extension cable
				Motor protector has activated				Allow to cool for 15 minutes
				Frozen				Wait for pump/water supply hose/accessory to
								thaw
		Motor stops		Fuse faulty / blown				Replace fuse
				Wrong mains voltage				Check that mains voltage corresponds to
								specifications on the model tag
				Motor protector has activated				Allow to cool for 15 minutes
		Fuses blow		Fuses incorrectly rated				Change to a mains supply higher than the pressure
								washer amp consumption
		Motor starts but no pressure		Nozzle partly blocked				Clean nozzle
		Motor “sounds” but fails to start		Insufficient power supply				Check that the voltage of the mains power supply
								line is the same as that on the plate
				Voltage loss due to use of extension				Check characteristics of extension cable
				cable
				Appliance not used for a long period				Contact your Bosch Service Centre
				of time
				Problems with TSS (Total Stop				Contact your Bosch Service Centre
				System) device
		F 016 L81 447 | (7.11.16)						Bosch Power Tools

OBJ_BUCH-1978-006.book Page 9 Monday, November 7, 2016 10:33 AM

English | 9

Problem

Possible Cause

Corrective Action

Pressure pulsating	Air in the inlet water supply
	hose/pump

Allow pressure washer to run with open spray handle and nozzle at low pressure until regular working pressure is obtained

	Inadequate water supply	Check that the water supply corresponds to
		specifications. The minimum specification for the
		water supply hose is 1/2" or 13 mm diameter
	Water filter blocked	Clean water filter
	Water supply hoses squeezed	Straighten out kinked water supply hoses
	High pressure hose too long	Remove high pressure extension hose. Retry
		(extension hose max. 7 m)
Pressure too low, but steady	Nozzle worn	Change the nozzle
Note: Several types of accessory	Start/stop valve worn	Activate trigger five times in quick succession
will normally deliver a lower
pressure
Motor starts up but with restricted	No water supply	Connect water supply
or no working pressure
	Water filter clogged up	Clean the water filter
	Nozzle clogged up	Clean nozzle
The pressure washer starts	Pump/ power gun leaky	Contact your Bosch Service Centre
irregularly by itself
Water leaks from machine	Leaking pump	A slight water leak is permissible; in case of
		excessive leak, contact Bosch Service Centre

No detergent taken in	Adjustable nozzle on high pressure
	setting

Attach the High Pressure Foam nozzle or select the foam setting on the 3 in1 nozzle

Detergent too dense	Dilute with water
High pressure hose extension being	Fit original hose
used

Deposits or restriction in detergent circuit

Flush with clean water and eliminate any restrictions. If the problem persists, contact your Bosch Service Centre.

Maintenance and Service

Maintenance

Stop, remove plug from the power supply and disconnect from water supply.

Note: To ensure long and reliable service, carry out the following maintenance regularly.

Regularly check for obvious defects such as loose fixings, and worn or damaged components.

Check that covers and guards are undamaged and correctly fitted. Carry out necessary maintenance or repairs before using.

After use/Storage

Turn the main switch off and operate the trigger to drain the water from the high pressure hose.

Clean the exterior of the machine thoroughly using a soft brush or cloth. Do not use water, solvents or polishes. Remove all debris, especially from the ventilation slots.

End of season storage: Drain water out of pump running motor for a few seconds. Pull trigger to release all water.

Do not place other objects on top of the machine.

Store in a frost-free area.

Ensure cables are not trapped when storing. Do not kink high pressure hose.

After-sales Service and Application Service www.bosch-do-it.com

In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the machine.

People’s Republic of China China Mainland

Bosch Power Tools (China) Co., Ltd. 567, Bin Kang Road

Bin Jiang District 310052 Hangzhou, P. R. China

Service Hotline: [phone] Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.com.cn

	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 10 Monday, November 7, 2016 10:33 AM

10 | English

HK and Macau Special Administrative Regions

Robert Bosch Hong Kong Co. Ltd. 21st Floor, 625 King’s Road North Point, Hong Kong

Customer Service Hotline: [phone] Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.com.hk

Indonesia

PT Robert Bosch Palma Tower 10th Floor

Jl. RA Kartini II-S Kaveling 6 Sek II Pondok Pinang, Kebayoran Lama Jakarta Selatan 12310 Indonesia

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail] www.bosch-pt.co.id

Philippines

Robert Bosch, Inc.

28th Floor Fort Legend Towers, 3rd Avenue corner 31st Street, Fort Bonifacio Global City, 1634 Taguig City, Philippines Tel.: [phone]

Fax: [phone] [e-mail] www.bosch-pt.com.ph

Bosch Service Center: 9725-27 Kamagong Street San Antonio Village

Makati City, Philippines Tel.: [phone] Fax: [phone]

E-Mail: [e-mail]

Malaysia

Robert Bosch Sdn. Bhd. No. 8A, Jalan 13/6 G.P.O. Box 10818 46200 Petaling Jaya Selangor, Malaysia

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail] Toll-Free: 1800 880188 www.bosch-pt.com.my

Thailand

Robert Bosch Ltd. Liberty Square Building No. 287, 11 Floor Silom Road, Bangrak Bangkok 10500

Tel.: [phone]

Fax: [phone]

Robert Bosch Ltd., P. O. Box 2054 Bangkok 10501, Thailand www.bosch.co.th

Bosch Service – Training Centre

La Salle Tower Ground Floor Unit No.2

10/11 La Salle Moo 16

Srinakharin Road

Bangkaew, Bang Plee

Samutprakarn 10540

Thailand

Tel.: [phone]

Fax: [phone]

Singapore

Powerwell Service Centre Ptd Ltd

65 Ubi Crescent, #06-03 Hola Centre Singapore 408559

Tel.: [phone] Fax: [phone]

E-Mail: [e-mail] Toll-Free: 1800 3338333 www.bosch-pt.com.sg

Vietnam

Robert Bosch Vietnam Co. Ltd 13th Floor , 194 Golden Building 473 Dien Bien Phu Street

Ward 25, Binh Thanh District 84 Ho Chi Minh City

Vietnam

Tel.: [phone]

Fax: [phone] Hotline: [phone]

E-Mail: [e-mail] www.bosch-pt.com.vn www.baohanhbosch-pt.com.vn

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 11 Monday, November 7, 2016 10:33 AM

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd. Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center Inside Australia:

Phone: [phone] Fax: [phone] Inside New Zealand: Phone: [phone] Fax: [phone] Outside AU and NZ: Phone: [phone] www.bosch-pt.com.au www.bosch-pt.co.nz

Egypt

Unimar

20 Markaz kadmat

El tagmoa EL Aoul – New Cairo

Tel: [phone] - 95 / + 2 02 224 78072 - 73 Fax:[phone]

E-Mail: [e-mail]

Ethiopia

Forever plc

Kebele 2,754, BP 4806, Addis Ababa , Ethiopia

Tel: [phone] E-Mail: [e-mail]

Nigeria

C. Woermann Ltd. P.O. Box 318

6, Badejo Kalesanwo Street Matori Industrial Estate Lagos, Nigeria

Tel: [phone] E-Mail: [e-mail]

Republic of South Africa

Customer service

Hotline: [phone]

Gauteng – BSC Service Centre

35 Roper Street, New Centre Johannesburg

Tel.: [phone]

Fax: [phone] E-Mail: [e-mail]

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street Pinetown

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

English | 11

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Bosch Headquarters

Midrand, Gauteng

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Environmental Protection

Chemicals dangerous to the environment must not be allowed to enter the ground, ground water or ponds, streams, etc.

For the use of cleaning agents, observe the instructions on the package and the prescribed concentration exactly.

For the cleaning of motor vehicles the local regulations should be observed: Do not allow oil sprayed off to enter into the ground water. Recycle raw materials instead of waste disposal.

Disposal

The pressure washer, accessories and packaging should be sorted for environmental-friendly recycling.

Do not dispose of pressure washers into household waste!

Only for EC countries:

According to the European directive 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national law, electrical and electronic equipment that are no longer usable must be collected separately and disposed of in an environmentally correct manner.

Subject to change without notice.

	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 12 Monday, November 7, 2016 10:33 AM

12 |

能造成危险。

IEC 61770

BA

/

和意外防范规定。



 30 mA



 IEC 60364- 1



 











 

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 13 Monday, November 7, 2016 10:33 AM

 12 7

1/2"



















| 13





 "ON"



 PSA /



 30 /





	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 14 Monday, November 7, 2016 10:33 AM

14 |

























Lo
Hi

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 15 Monday, November 7, 2016 10:33 AM

| 15

	0 40
		AQT 35-12/		AQT 37-13/	AQT 40-13
		AQT 35-12+		AQT 37-13+
		3 600 HA7 1..	3 600 HA7 2..		3 600 HA7 5..
	kW	1,5		1,7	1,9
	°C	40		40	40
	/	5,8		6,2	6,6
	MPa	12		13	13
	MPa	8		9	9
	/	5		5,5	6
	MPa	1		1	1
					
EPTA-Procedure 01:2014		6,65/8,12		7,83/8,82	8,9
		/II		/II	/II
				( )

230 V 0,153

	1	58–59
	2	60
	3	61
/	4	61
	5	62–64
	6	64
/	7	65
	8	65
	9	66
	10	66
	11	67
	12	67
/ /	13	68
	14	68
	15	68
	16	69

从插座上拔出插头。如果电线受损、被割坏 或缠绕在一起也要执行以上的防范措施。

230 V AC, 50 Hz ( 220 V, 240 V )

-1,5 20

-2,5 50

头和

长线、插头和联结装置。

	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 16 Monday, November 7, 2016 10:33 AM

16 |

30 mA(RCD)

理。

胶套。延长线上必须配备塞绳扣。

上。

"0"

达。

管来拉动高压清洁机。这样可能导致高压清洁机摇晃并 且翻倒。

保护高压软管免被锋利的边缘或尖锐的凸角割损。

! Patio Cleaners



容器上所标示的有关稀释清洁剂的建议说明。

1:

3 1

2:

接着再从上端朝下冲洗。

器清洁。只能吸汲干净的水。

/

–3

, 0,515

3 3

清洁机流出的水稳定且均匀为止。如果过了25 ,,

的插入联结器中。如果连接不紧密会影响吸力。

洁机上。

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 17 Monday, November 7, 2016 10:33 AM

| 17

								15
								15
								1/2 13
								- 7
		:		/				5
								3 1
		
		Bosch Power Tools						F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 18 Monday, November 7, 2016 10:33 AM

18 |

/

马达的通气缝隙。

行数秒并扣动扳机。

www.bosch-do-it.com

10

询。

滨江区滨康路567

3100524008268484(0571) [e-mail] www.bosch-pt.com.cn

 625 21

[phone]+852 2590 [e-mail]

Robert Bosch Power Tools GmbH

·

70538 Stuttgart / GERMANY

70538 /

规定的使用浓度。

来的油垢流入地下水中。

规2012/19/EU

能造成危險。

IEC 61770

BA

	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 19 Monday, November 7, 2016 10:33 AM

/

和意外防範規定。



 30 mA





IEC 60364-1



 





| 19







 

 12,7

1/2"









	Bosch Power Tools				F 016 L81 447 | (7.11.16)

OBJ_BUCH-1978-006.book Page 20 Monday, November 7, 2016 10:33 AM

20 |















 "ON"



 PSA /



 30 /











	F 016 L81 447 | (7.11.16)				Bosch Power Tools

OBJ_BUCH-1978-006.book Page 21 Monday, November 7, 2016 10:33 AM













| 21







Lo
Hi

以利用本機器清潔戶外的空地和放在戶外的物體。也可 以使用本機器清潔機械設備、車輛和船。

0 °C 40 °C

	Bosch Power Tools				F 016 L81 447 | (7.11.16)