BOE OPTOELECTRONICS HV133WX1-100 SPECIFICATION

PROPRIETARY NOTE

THIS SPECIFICATION IS THE PROPERTY OF BOE HYDIS AND SHALL NOT
BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF
BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST

TITLE : HV133WX1-100

Product Specification

Rev. 0

www.jxlcd.com

www.jxlcd.com

SPEC. NUMBER

S864-1360

BOE HYDIS TECHNOLOGY

PRODUCT GROUP

REV.

ISSUE DATE

2008.05.280TFT LCD

PAGE

PAGE

1

OF 34

B2005-C001-A (1/3)

A4(210 X 297)

A4(210 X 297)

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

0 2008.05.28

REVISION HISTORY

REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED

0  Initial Release 08.05.28 H.S. KIM

www.jxlcd.com

SPEC. NUMBER

S864-1360

www.jxlcd.com

SPEC TITLE

HV133WX1-100 Product Specification

PAGE

2

OF 34

B2005-C001-A (2/3) A4(210 X 297)

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

0 2008.05.28

Contents

No Item Page

1.0 General Description 4

2.0 Absolute Maximum Ratings 6

3.0 Electrical Specifications 7

4.0 Optical Specifications 9

5.0 Interface Connections 14

6.0 Signal Timing Specifications 17

7.0 Signal Timing Waveforms 17

8.0 Input Signals, Basic Display Colors & Gray Scale of Colors 19

9.0 Power Sequence 20

10.0 Mechanical Characteristics 21

11.0 Mechanical Drawing 22

12.0 Reliability Test 25

13.0 Handling & Cautions 26

14.0 Labels 27

15.0 Packing Information 29

16.0 EDID Table 30

www.jxlcd.com

www.jxlcd.com

SPEC. NUMBER

S864-1360

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HV133WX1-100 Product Specification

PAGE

OF 34

3

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

0 2008.05.28

1.0 GENERAL DESCRIPTION

1.1 Introduction

HV133WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 13.3 inch
diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this
module is a low reflection and higher color type.

LVDS
Input
Signal

Connector (CN

LVDS Rx

+

T/CON

Gate Driver

TFT LCD Panel

BACK LIGHT (Fluorescent Lamp)

1280 ×800

1

VDD

www.jxlcd.com

www.jxlcd.com

1

)

HVDD
VDIM/

VSW

1.2 Features

 Thin and Light Weight
 3.3 V Logic Power Supply
 12V Back-light Power Supply
 1 Channel LVDS Interface
 SMD LED (54EA) Array (Bottom Side/Horizontal Direction)
 262,144 Colors
 Data Enable Signal Mode
 On Board EDID chip
 Side Mounting Frame
 Green Product (RoHS)

DC/DC

Gamma

Vcom

LED Driver

Back Light (SMD LED Array)

Source Driver

CN2

SPEC. NUMBER

S864-1360

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HV133WX1-100 Product Specification

PAGE

OF 34

4

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

1.3 Application

 Tablet PC (Wide type)

1.4 General Specifications

Parameter Specification Unit Remarks

Active area 286.08(H) ×178.80(V) mm

Number of pixels 1280(H) ×800(V) pixels

Pixel pitch 0.2235(H) ×0.2235(V) mm

Pixel arrangement RGB Vertical Stripe

Display colors 262,144 colors

0 2008.05.28

Display mode Normally Black

Outline dimension

Weight 275(Typ.) ± 10 g Note 2

Back-light SMD LED Array (54EA : 9 series X 6 parallel)

Note 1 : at PCB side
Note 2 : without digitizer

www.jxlcd.com

www.jxlcd.com

301.4±0.3(H) ×196.5±0.3(V) ×6.5(D:Max.)

mm Note 1

SPEC. NUMBER

S864-1360

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HV133WX1-100 Product Specification

PAGE

OF 34

5

PRODUCT GROUP

Temperature (

)

(40, 90)

(60, 27)

100

806040

20

90

Relative Humudity

5

REV ISSUE DATE

TFT LCD PRODUCT

0 2008.05.28

2.0 ABSOLUTE MAXIMUM RATINGS

The followings are maximum values which, if exceed, may cause faulty operation or

damage to the unit.

Parameter Symbol Min. Max. Unit Remarks

Logic Power Supply Voltage

Logic Power Supply Voltage

Back-light Power Supply Voltage HV

Back-light LED Current

+ 25 ℃
+ 50 ℃

Back-light LED Reverse Voltage

Operating Temperature

Storage Temperature

V

V

LED

I

LED

V

T

T

DD

IN

R

OP

SP

DD

-0.3 4.0 V

-0.3 VDD+0.3 V

-0.3 25 V

mA30-I

- 20 mA

- 5 V

0 +50

-20 +60

℃

℃

Ta=25+/-2°C

Note 1

Note 1, Note 2

Note 1. Ambient temperature vs maximum forward current are shown in the figure below.

Note 2. Temperature and relative humidity range are shown in the figure below.

www.jxlcd.com

90% RH Max. ( 40℃ ≥ Ta)

www.jxlcd.com

Maximum wet - bulb temperature at 39℃ or less. ( > 40℃) No condensation.

Ambient Temperature vs Maximum Forward Current

(50,20)

(50,20)

(50,20)(50,20)

Operating Range

Storage Range

(50, 50)

SPEC. NUMBER

B2005-C001-A (3/3) A4(210 X 297)

S864-1360

SPEC TITLE

HV133WX1-100 Product Specification

-40 -20 0 20 40 60 80

℃℃℃℃

PAGE

OF 34

6

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

3.0 ELECTRICAL SPECIFICATIONS

3.1 Electrical Specifications

< Table 3. Electrical Specifications >

Parameter Min. Typ. Max. Unit Remarks

Logic Power Supply Voltage

Logic Power Supply Current

Back-light Power Supply Voltage

Back-light Power Supply Current

Back-light Power Consumption

Power Consumption (EBL)

LED Driver’s Efficiency

Back-light PWM Frequency

High Level PWM Signal Voltage

Low Level PWM Signal Voltage

High Level Differential Input
Signal Voltage

V

I

HV

I

HVDD

P

P

F

V

PWMH

V

PWML

V

DD

DD

DD

BL

EBL

η

PWM

IH

0 2008.05.28

3.0 3.3 3.6 V Note 1

- 360 550 mA Note 1

5.0 12.0 21.0 V Note 2

- 271 325 mA Note 2, 3

- 3.25 3.90 W Note 2, 3

- 1.85 1.98 W Note 1, 2, 3

80 85 - % Note 2, 3

200 280 350

2.2 3.3 5.0 V

- 0 0.2 V

- - +100 mV VCM= 1.2V

㎐

Low Level Differential Input
Signal Voltage

Back-light LED Voltage /
Back-light LED Total Voltage

Back-light LED Current /
Back-light LED Total Current

Life Time 12,000 - - Hrs

Power Consumption

www.jxlcd.com

www.jxlcd.com

V

/V

I

V

LED

/I

IL

LED

BL

BL

P

P

P

D

LED

total

-100 - - mV VCM= 1.2V

-

-

- 1.2 1.82 W Note 1

- 2.76 3.27 W Note 4

- 3.96 5.09 W Note 1, 4

3.2

/ 28.8

16.0

/ 96.0

3.6

/32.4

16.8

/100.8

V Note 4

mA Note 4

Based on LED
25’c, I

LED

=16mA

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.

The current draw and power consumption specified is for 3.3V at 25℃.
a) Typ : Window XP pattern, b) Max : Skip Sub Pixel
c) EBL : Mosaic pattern ( 32 X 32 )

2. The power supply voltage and current is measured and specified at the interface
connector of LCM including LED Driver.

3. Reference value, which is measured with LED Driver for 12V.

4. Reference value, which is measured without LED Driver.

5. Calculated value for reference (V

SPEC. NUMBER

S864-1360

SPEC TITLE

HV133WX1-100 Product Specification

LED

× I

× # of LEDs (54EA) ).

LED

PAGE

OF 34

7

B2005-C001-A (3/3) A4(210 X 297)

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

3.2 PWM Duty Ratio vs Brightness

100

90

80

70

60

50

40

30

Relative Brightness (%)

20

10

0

0 10 20 30 40 50 60 70 80 90 100

0 2008.05.28

Duty Ratio (%)

www.jxlcd.com

www.jxlcd.com

Notes :

In case of duty ratio 0%, LED can’t illuminate itself so this state is LED off.
In case of duty ratio 100%, the brightness of LED is maximum and the state is LED on.

SPEC. NUMBER

S864-1360

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HV133WX1-100 Product Specification

PAGE

OF 34

8

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

0 2008.05.28

4.0 OPTICAL SPECIFICATIONS

4.1 Overview

The test of optical specifications shall be measured in a dark room (ambient luminance ≤ 1
lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer
system and TOPCON BM-5A) and test unit shall be located at an approximate distance
50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θ
(=θ3 ) as the 3 o’clock direction (the “right”), θ
(“upward”), θ

(= θ9 ) as the 9 o’clock direction (“left”) and θ

Ø=180

(= θ12 ) as the 12 o’clock direction

Ø=90

(= θ6 ) as the 6

Ø=270

o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on
the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to
measurement. VDDshall be 3.3+/- 0.3V at 25°C. Optimum viewing angle direction is 6
o’clock.

4.2 Optical Specifications

<Table 4. Optical Specifications>

Parameter Symbol Condition Min. Typ. Max. Unit Remarks

Horizontal

Viewing Angle

range

Vertical

Luminance Contrast ratio CR

Luminance of

White
White

Luminance

uniformity

www.jxlcd.com

www.jxlcd.com

1 Point Y

5 Points ΔY5 80 - -

13 Points ΔY13 60 - -

Θ
Θ

Θ

Θ

W

White Chromaticity

W

R

Red

R

Reproduction

of color

Green

G
G
B

Blue

B

Response

Time

Total

(Tr+ Td)

3

9

12

6

w

x

y

x

y

x

y

x

y

CR > 10

Θ = 0°

Θ = 0°

Θ = 0°

Θ = 0°

Ta= 25° C

Θ = 0°

- 89 90 Deg.

- 89 90 Deg.

- 89 90 Deg.

- 89 90 Deg.

400 500 - Note 2

250 300 - cd/m

0.260 0.300 0.340

0.280 0.320 0.360

0.523 0.563 0.603

0.314 0.354 0.394

0.291 0.331 0.371

0.502 0.542 0.582

0.106 0.146 0.186

0.077 0.117 0.157

- 30 - ms Note 6

2

%

Ø=0

Note 1

Note 4
Note 5

Note 3

Cross Talk CT

SPEC. NUMBER

S864-1360

Θ = 0°

SPEC TITLE

HV133WX1-100 Product Specification

- - 2.0 % Note 7

PAGE

OF 34

9

B2005-C001-A (3/3) A4(210 X 297)

PRODUCT GROUP

REV ISSUE DATE

TFT LCD PRODUCT

Notes :

1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing
angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6,
12 o’clock direction with respect to the optical axis which is normal to the LCD surface
(see Figure1).

2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of
the LCD surface. Luminance shall be measured with all pixels in the view field set first
to white, then to the dark (black) state (see Figure1). Luminance Contrast Ratio (CR) is
defined mathematically as CR = Luminance when displaying a white raster / Luminance
when displaying a black raster.

3. Reference only / Standard Front Surface Treatment Measured with green cover glass.
The color chromaticity coordinates specified in Table 4 shall be calculated from the
spectral data measured with all pixels first in red, green, blue and white. Measurements
shall be made at the center of the panel.

0 2008.05.28

www.jxlcd.com

SPEC. NUMBER

S864-1360

www.jxlcd.com

SPEC TITLE

HV133WX1-100 Product Specification

10

PAGE

OF 34

B2005-C001-A (3/3) A4(210 X 297)