BOE OPTOELECTRONICS HT141WX1-101 SPECIFICATION

Page 1

PROPRIETARY NOTE

THIS SPECIFICATION IS THE PROPERTY OF BOE HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST

TITLE : HT141WX1-101

Product Specification

Rev. A

www.jxlcd.com

BOE HYDIS TECHNOLOGY

SPEC. NUMBER

S864-1260

B2005-C001-A (1/3) A4(210 X 297) A4(210 X 297)

PRODUCT GROUP

TFT LCD

REV.

ISSUE DATE

2006.04.05

PAGE

OF 31

Page 2

PRODUCT GROUP

REVISION HISTORY

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

PreparedDateDescription Of ChangesECN NO.REV.

S.E.Park2005.12.27Initial Release0

E0603-F040A

made a hole at mylar tape (p.27)

.Fixing tape attached

attached a 60mm PET tape to fix the CCFL cable (p.26~27)

www.jxlcd.com

B.C.Kim2006.04.05.Shield cover changed

SPEC. NUMBER

S864-1260 2

B2005-C001-A (2/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 3

PRODUCT GROUP

Contents

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

PageItemsNo.

4General Description1.0 6Absolute Maximum ratings2.0 7Electrical specifications.3.0

9Optical specifications.4.0 14Interface Connection5.0 17Signal Timing Specification6.0

www.jxlcd.com

17Signal Timing waveforms7.0 19Input Signals, Display Colors & Gray Scale of Colors8.0 20Power Sequence9.0 21Mechanical Characteristics10.0 22Reliability Test11.0 22Handling & Cautions.12.0 23Label13.0 25Packing information14.0 26Mechanical Outline Dimension15.0 28EDID Table16.0

SPEC. NUMBER

S864-1260 3

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 4

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

1.0 GENERAL DESCRIPTION

1.1 Introduction

HT141WX1-101 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 14.1 inch diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is a low reflection and higher color type. Therefore, this module is suitable for Notebook PC. The DC/AC inverter for back-light driving is not built in this model.

Source Driver

LVDS Input

Connector (CN )

Signal

LVDS Rx

T/CON

Gate Driver

VDD

www.jxlcd.com

I2C bus

1.2 Features

z 14.1 WXGA TN z Thin and light weight z 3.3 V power supply z 1 Channel LVDS Interface z Single CCFL (Bottom side/Horizontal Direction) z 262,144 colors z Data enable signal mode z Side Mounting Frame z Green Product (RoHS)

z On board EDID chip

z High contrast ratio

DC/DC

Gamma

Vcom

EDID/EEPROM

Reflector

TFT LCD Panel

BACK LIGHT (Fluorescent Lamp)

1280 ×800

Backlight Unit

LAMP

CN2

1 (Hot)

2 (Cold)

SPEC. NUMBER

S864-1260 4

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 5

PRODUCT GROUP

1.3 Application

z Notebook PC (Wide type)

1.4 General Specification

The followings are general specifications at the model HT141WX1-101. (listed in Table 1.)

mm303.36 (H) ×189.6 (V) (14.1” diagonal)Active area

pixels1280(H) ×800(V)Number of pixels

mm0.237(H) ×0.237(V)Pixel pitch

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

RemarksUnitSpecificationParameter

RGB Vertical stripePixel arrangement

Normally WhiteDisplay mode

www.jxlcd.com

Dimensional outline

Power consumption

Note 1: CCFL (Cold Cathode Fluorescent Lamp)

www.jxlcd.com

319.5±0.5(H) ×205.5±0.5(V) ×5.5(D:max)

AG(H40%)/AR/2HSurface treatment

: 5.1

total

colors262,144Display colors

g390 (typ) / 405 (max)Weight

Note 1Bottom edge side, 1-CCFL typeBack-light WPD: 1.1 WPBL: 4.0 WP

SPEC. NUMBER

S864-1260 5

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 6

PRODUCT GROUP

Temp

(

)

(40,

)

(

)

(

)

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

2.0 ABSOLUTE MAXIMUM RATINGS

The followings are maximum values which, if exceed, may cause faulty operation or

damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2.

< Table 2. Absolute Maximum Ratings>

Ta=25+/-2°C

RemarksUnitMax.Min.SymbolParameter

Power Supply Voltage Logic Supply Voltage Lamp Current Lamp frequency Operating Temperature Storage Temperature

+500T +70-20T

V4.0-0.3V VVDD+0.3-0.3V

mArms7.02.0I

Note1

kHz8040F

℃

Note2

℃

Note (1) Permanent damage to the device may occur if maximum values are exceeded

Functional operation should be restricted to the condition described under normal operating conditions.

www.jxlcd.com

Note (2) Temperature and relative humidity range are shown in the figure below.

www.jxlcd.com

95 % RH Max. ( 40 OC ≥ Ta) Maximum wet - bulb temperature at 39 OC or less. (Ta > 40 OC) No condensation.

Relative Humudi

100

Operating Range

50, 50

60, 27

Storage Range

-40 -20 0 20 40 60 80

SPEC. NUMBER

S864-1260 6

SPEC TITLE

HT141WX1-101 Product Specification

erature

℃

PAGE

OF 31

B2005-C001-A (3/3) A4(210 X 297)

Page 7

PRODUCT GROUP

3.0 ELECTRICAL SPECIFICATIONS

3.1Electrical Specifications

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

Power Supply Voltage Permissible Input Ripple

Voltage Power Supply Current High Level Differential Input

Signal Voltage Low Level Differential Input

Signal Voltage Back-light Lamp Voltage Back-light Lamp Current Back-light Lamp operating

Frequency

Lamp Start Voltage

www.jxlcd.com

< Table 3. Electrical specifications >

660-V

1,240--

IBL= 6.0mA

RemarksUnitMax.Typ.Min.Parameter

Note1V3.63.33.0V At V Note1mA520330-I

mV100--V

rms

mA7.06.02.0I

KHz806540F

rms

Vrms1,490--

Note2V

One Lamp , Note3

At Ta = 25℃ Note 4

At Ta = 0℃ Note 4

= 3.3VmV100--V

Note5Hrs-15,00010,000Lamp Life

Power Consumption

SPEC. NUMBER

S864-1260 7

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

total

HT141WX1-101 Product Specification

W5.1-P

Note1W1.1-P Note6W4.0-P

PAGE

OF 31

Page 8

PRODUCT GROUP

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.

The current draw and power consumption specified is for 3.3V at 25℃.

a) Typ : Window XP pattern b) Max : Vertical 2 line skip pattern

2. Reference value, which is measured with Samsung Electric SIC-180 Inverter. (VBL Min is value at IBL Min and VBL Max is value at IBL Max)

3. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference which may cause line flow on the display.

4. For starting the backlight unit, the output voltage of DC/AC's transformer should be larger than the minimum lamp starting voltage. (1,240 Vrms at 25 ℃ & 1,490 Vrms at 0 ℃) If an inverter has shutdown function it should keep its output for more than 1 second even if the lamp connector open. Otherwise the lamps may not to be turned on.

5. End of Life shall be determined by the time when any of the following is satisfied under continuous lighting at 25℃ and IBL= 6.0[mA] Max Only. y Intensity drops to 50% of the Initial Value.

6. Calculated value for reference (VBL × IBL)

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

www.jxlcd.com

SPEC. NUMBER

SPEC TITLE

PAGE

S864-1260 8

B2005-C001-A (3/3) A4(210 X 297)

HT141WX1-101 Product Specification

OF 31

Page 9

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

4.0 OPTICAL SPECIFICATION

4.1 Overview

The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θand/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement... VDD shall be 3.3+/- 0.3V at 25°C. Optimum viewing angle direction is 6 ’clock.

4.2 Optical Specifications

RemarkUnitMax.Typ.Min.ConditionSymbolParameter

Viewing Angle

range

Center

Luminance of

White White

Luminance

uniformity

White Chromaticity

Reproduction

of color

Response Time

(Rising + Falling)

www.jxlcd.com

CRLuminance Contrast ratio

CR > 10

Θ = 0°

IBL = 6mA

Θ = 0°

Ta= 25° C

Θ = 0°

-200170

-1851505 Points

--80ΔY55 Points

--60ΔY1313 Points

0.2590.3290.299y

0.6130.5830.553

0.3680.3380.308y

0.3350.3050.275x

0.5870.5570.527y

0.1780.1480.118x

0.1710.1410.111y

Horizontal

Vertical

www.jxlcd.com

1 Point

Red

Green

Blue

Deg.-4540

Deg.-2015 Deg.-4540

cd/m

ms50-

Note 1Deg.-4540

Note 2-300250

Note 30.3430.3130.283

CTCross Talk

SPEC. NUMBER

S864-1260 9

SPEC TITLE

HT141WX1-101 Product Specification

Θ = 0°

%2.0--

PAGE

OF 31

B2005-C001-A (3/3) A4(210 X 297)

Page 10

PRODUCT GROUP

Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The

viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE1 shown in Appendix).

2. Contrast measurements shall be made at viewing angle of Θ= 0　 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state .

(see FIGURE1 shown in Appendix) Luminance Contrast Ratio (CR) is defined

mathematically as CR = Luminance when displaying a white raster / Luminance when displaying a black raster.

3. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue, and white. Measurements shall be made at the center of the panel.

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

www.jxlcd.com

SPEC. NUMBER

SPEC TITLE

PAGE

S864-1260 10

B2005-C001-A (3/3) A4(210 X 297)

HT141WX1-101 Product Specification

OF 31

Page 11

4.2 Optical measurements

Photo detector

( TOPCON BM-5A)

PRODUCT GROUP

Figure 1. Measurement Set Up

Field = 2

50 cm

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

TFT-LCD module

Center of the screen

Optical characteristics measurement setup

Figure 2. White Luminance and Uniformity Measurement Locations (5 points)

Column

Row

www.jxlcd.com

200

400

600

320 640 960

LCD panel

Center Luminance of white is defined as luminance values of center 1 point and 5 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display.

SPEC. NUMBER

S864-1260 11

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 12

PRODUCT GROUP

Figure 3. Uniformity Measurement Locations (13 points)

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

10mm 10mm

192

384

576

The White luminance uniformity on LCD surface is then expressed as : ΔY5 = Minimum Luminance of five points / Maximum Luminance of five points (see FIGURE 2) , ΔY13 = Minimum Luminance of 13 points /Maximum Luminance of 13 points (see FIGURE 3).

www.jxlcd.com

320 640 960

10mm

Figure 4. Response Time Testing

Display data

Optical Response

The electro-optical response time measurements shall be made as shown in FIGURE 4 (shown in Appendix) by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td and 90% to 10% is Tr.

SPEC. NUMBER

S864-1260 12

B2005-C001-A (3/3) A4(210 X 297)

White(TFT OFF)

100%

90%

10%

SPEC TITLE

HT141WX1-101 Product Specification

Black(TFT ON)

White(TFT OFF)

Time

PAGE

OF 31

Page 13

PRODUCT GROUP

Figure 5. Cross Modulation Test Description

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

VIEW AREA

L31

YA(1120, 400)

YB-Y

Cross-Talk (%) = × 100

Where:

YA= Initial luminance of measured area (cd/m2) YB= Subsequent luminance of measured area (cd/m2)

The location measured will be exactly the same in both patterns

www.jxlcd.com

Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark (Refer to FIGURE 5).

VIEW AREA

320,200

960,200

YB(1120, 400)

960,600320,600

SPEC. NUMBER

S864-1260 13

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 14

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

5.0 INTERFACE CONNECTION.

5.1 Electrical Interface Connection

The electronics interface connector is a model FI-XB30S-HFxx manufactured by JAE or equivalent. The mating connector part number is FI-X30S or equivalent. The connector interface pin assignments are listed in Table 5.

FunctionsSymbolTerminal

GroundGND1 Power Supply: +3.3VVDD2 Power Supply: +3.3VVDD3 EDID +3.3VVEDID4 ReservedReserved5 EDID ClkClk EDID6 EDID DataData EDID7 Transmission Data of 0 Negative -RxIN0-8 Transmission Data of 0 Positive +RxIN0+9 GroundGND10 Transmission Data of 0 Negative -RxIN1-11 Transmission Data of 0 Positive +RxIN1+12

www.jxlcd.com

GroundGND13 Transmission Data of 0 Negative -RxIN2-14 Transmission Data of 0 Positive +RxIN2+15 GroundGND16 Sampling Clock of Negative -RxCLKIN-17 Sampling Clock of Positive +RxCLKIN+18 GroundGND19 No ConnectionNC20 No ConnectionNC21 GroundGND22 No ConnectionNC23 No ConnectionNC24 GroundGND25 No ConnectionNC26 No ConnectionNC27 GroundGND28 No ConnectionNC29 No ConnectionNC30

SPEC. NUMBER

S864-1260 14

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 15

5-2. LVDS Interface

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

R0~R5 G0~G5

B0~B5

Hsync Vsync

CLK

PC Side

6 6

TTL Parallel-to-LVDS

PLL

CN1

100 ohm

TFT-LCD Side

LVDS to TTL Parallel

PLL

6 6

R0~R5

G0~G5 B0~B5

Hsync Vsync

CLK

Note. Transmitter : Thine THC63LVDM63A or equivalent. Transmitter is not contained

in Module.

5.3.LVDS Input signal

CLK+

www.jxlcd.com

Vdiff=0V

Rin0

Rin1

Rin2

Prior cycle

GO R5 R4 R3 R2 R1 R0

B1 B0 G5 G4 G3 G2 G1

DE Vsync B5 B4 B3 B2Hsync

Signal for 1 DCLK cycle Next cycle

Note. Pin connection in case of using Thine THC63LVDM63A

SPEC. NUMBER

S864-1260 15

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

B2005-C001-A (3/3) A4(210 X 297)

Page 16

PRODUCT GROUP

TransmitterInput signalTransmitterInput signal

TB3(10)G4CLK IN(26)DCLK TB4(12)G5TA0(44)R0 TB5(13)B0TA1(45)R1

TB6(15)B1TA2(47)R2 TC0(16)B2TA3(48)R3 TC1(18)B3TA4(1)R4 TC2(19)B4TA5(3)R5

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

TC3(20)B5TA6(4)G0 TC4(22)HsyncTB0(6)G1 TC5(23)VsyncTB1(7)G2

www.jxlcd.com

5.4.Back-light Interface

The Back-light interface connector is a model BHSR-02VS-1 manufactured by JST or equivalent. The connector interface pin assignments are listed in Table 7.

TC6(25)DETB2(9)G3

ColorFunctionSymbolTerminal No.

BlueCCFL Power Supply(High Voltage)VL1

WhiteCCFL Power Supply(GND Side)GL2

SPEC. NUMBER

S864-1260 16

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 17

PRODUCT GROUP

6.0. SIGNAL TIMING SPECIFICATION

The specification of the signal timing parameters are listed in Table 8.

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

UnitMaxTypMinSymbolsItem

Lines-823804T1Frame Period

Lines-800-T2Vertical Display Period Clocks-14401350T3One line Scanning Period Clocks-1280-T4Horizontal Display Period

MHz-71.11-1/T5Clock Frequency

7.0 SIGNAL TIMING WAVEFORMS

7.1 Timing wave forms of interface signal

www.jxlcd.com

DCLK

DATA SIGNALS

Valid display data (1600 Clocks)

SPEC. NUMBER

S864-1260 17

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 18

PRODUCT GROUP

7.2 LVDS Rx Interface Timing Parameter

The specification of the LVDS Rx interface timing parameter is listed in Table 9.

msec25.0014.0612.50tRPLLPLL Set

nsec+0.40.0-0.4tRIP0Input Data 0 nsectRICP/7+0.4tRICP/7tRICP/7-0.4tRIP1Input Data 1

nsec2 ×tRICP/7+0.42 ×tRICP/72 ×tRICP/7-0.4tRIP2Input Data 2 nsec3 ×tRICP/7+0.43 ×tRICP/73 ×tRICP/7-0.4tRIP3Input Data 3 nsec4 ×tRICP/7+0.44 ×tRICP/74 ×tRICP/7-0.4tRIP4Input Data 4

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

RemarkUnitMaxTypMinSymbolItem

www.jxlcd.com

tRIP6

tRIP5

tRIP4

tRIP3

tRIP2

tRIP1

tRIP0

RxINz +/-

* Z = 0, 1, 2

RxCLKIN+/-

Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0Rx3

Vdiff=0[v]Vdiff=0[v]

tRCIP

nsec5 ×tRICP/7+0.45 ×tRICP/75 ×tRICP/7-0.4tRIP5Input Data 5 nsec6 ×tRICP/7+0.46 ×tRICP/76 ×tRICP/7-0.4tRIP6Input Data 6

SPEC. NUMBER

S864-1260 18

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 19

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS

Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144 colors are derived from the resultant 18 bit data. Table 10. shows the input signals, basic display colors and gray scale for each color.

Colors & Data signal

Gray scale R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Basic Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

colors Light Blue 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1

Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Purple 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△

Gray Darker 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

scale

Red Brighter 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Gray Darker 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0

scale

Green Brighter 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0

Gray Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0

scale

Blue Brighter 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1

Gra y

scale Darker 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0

White

& Brighter 1 0 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1

Black

△ ▽

▽

Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

www.jxlcd.com

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

www.jxlcd.com

△

△ ▽

▽

Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△

△ ▽

▽

Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△

△ ▽

▽

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

↓↓ ↓ ↓↓ ↓

0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0

↓↓ ↓ ↓↓ ↓

0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0

↓↓ ↓ ↓↓ ↓

0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1

1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0

↓↓ ↓ ↓↓ ↓

0 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1

SPEC. NUMBER

S864-1260 19

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

B2005-C001-A (3/3) A4(210 X 297)

Page 20

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

9.0 POWER SEQUENCE

To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below

Power Supply

Interface Signal

Back- light

www.jxlcd.com

0.9VDD

0.1VDD

Valid

T3 T4

● T1 ≤ 10 ms

● 0 ≤ T2 ≤ 50 ms

● 200 ms ≤ T3

● 200 ms ≤ T4

● 0 ≤ T5 ≤ 50 ms

● 0 ≤ T6 ≤ 10ms

● 150ms ≤ T7

0.9VDD

0.1VDD

Notes : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep

high impedance.

2. Do not keep the interface signal high impedance when power is on. Back Light must be turn on after power for logic and interface signal are valid.

SPEC. NUMBER

S864-1260 20

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 21

PRODUCT GROUP

10.0 MECHANICAL CHARACTERISTICS

10.1 Dimensional Requirements

FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT141WX1-101. Other parameters are shown in Table 11.

303.36 (H) ×189.6 (V)Active Area

1280 (H) X 800 (V) (1 pixel = R + G + B dots)Number of pixels

0.237 (H) X 0.237 (V)Pixel pitch RGB Vertical stripePixel arrangement

262,144Display colors

Normally whiteDisplay mode

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

UnitSpecificationParameter

Connector : BHSR-02VS-1

Back-light

www.jxlcd.com

10.2 Mounting

See FIGURE 6. (shown in Appendix)

10.3 Glare and Polarizer Hardness.

The surface of the LCD has an Glare coating to minimize reflection and a coating to reduce scratching.

10.4 Light Leakage

There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 350lux.

CCFL, Horizontal-lamp type

mm319.5±0.5×205.5±0.5×5.5 maxDimensional outline

gram390 (typ) / 405 (max)Weight

mmCable Length : 70.0±5.0

SPEC. NUMBER

S864-1260 21

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 22

PRODUCT GROUP

11.0 RELIABILITY TEST

The Reliability test items and its conditions are shown in below.

ConditionsTest ItemsNo

Ta = 60 ℃, 240 hrsHigh temperature storage test1 Ta = -20 ℃, 240 hrsLow temperature storage test2

High temperature & high humidity operation test

Vibration test (non-operating)

Shock test (non-operating)

Electro-static discharge test (non-operating)

Ta = 50 ℃, 80%RH, 240 hrs Ta = 50 ℃, 240 hrsHigh temperature operation test4

Ta = 0 ℃, 240 hrsLow temperature operation test5 Ta = -20 ℃↔60 ℃ (0.5 hr), 100 cycleThermal shock6

1.5G,10~300Hz for X,Y,Z axis 30 minutes for each axis

220G,2msec,half sine (6 times) Air : 150 pF, 330Ω, 15 KV

Contact : 150 pF, 330Ω, 8 KV

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

www.jxlcd.com

12.0 HANDLING & CAUTIONS

(1) Cautions when taking out the module

y Pick the pouch only, when taking out module from a shipping package.

(2) Cautions for handling the module

y As the electrostatic discharges may break the LCD module, handle the LCD module with

care. Peel a protection sheet off from the LCD panel surface as slowly as possible.

y As the LCD panel and back - light element are made from fragile glass material, impulse

and pressure to the LCD module should be avoided.

y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth

without chemicals for cleaning.

y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care.

(3) Cautions for the operation

y When the module is operating, do not lose CLK, ENAB signals. If any one of these signals

is lost, the LCD panel would be damaged.

y Obey the supply voltage sequence. If wrong sequence is applied, the module would be

damaged.

SPEC. NUMBER

www.jxlcd.com

SPEC TITLE

PAGE

S864-1260 22

B2005-C001-A (3/3) A4(210 X 297)

HT141WX1-101 Product Specification

OF 31

Page 23

PRODUCT GROUP

(4) Cautions for the atmosphere

y Dew drop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or humidity

atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended.

(5) Cautions for the module characteristics

y Do not apply fixed pattern data signal to the LCD module at product aging. y Applying fixed pattern for a long time may cause image sticking.

(6) Other cautions

y Do not disassemble and/or re-assemble LCD module. y Do not re-adjust variable resistor or switch etc. y When returning the module for repair or etc., Please pack the module not to be broken.

We recommend to use the original shipping packages.

13.0 LABEL

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

(1) Product label

www.jxlcd.com

Type designation

No 1. Control Number

No 2. Rank / Grade

No 3. Company (H:BOE HYDIS, O:BOE OT)

23 4

HT141WX1-101

XXXXXX X100XX X XXX

No 5. Month (1, 2, 3, …, 9, X, Y, Z)

No 6. Product Identification (FG)

No 7. Serial Number

No 4. Year (5 : 2005, 6: 2006, …)

SPEC. NUMBER

S864-1260 23

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 24

PRODUCT GROUP

(2) High voltage caution label

(3) Box label

Label Size: 108 mm (L) × 56 mm (W) Contents Model: HT141WX1-101 Q`ty: Module Q`ty in one box Serial No.: Box Serial No. See next figure for detail

description. Date: Packing Date FG Code: FG Code of Product

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

www.jxlcd.com

HT141WX1-101

* 0000000000000 *

00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no

SPEC. NUMBER

SPEC TITLE

3360

200X.X.XX

1 0

FG CODE

RoHS Mark

PAGE

S864-1260 24

B2005-C001-A (3/3) A4(210 X 297)

HT141WX1-101 Product Specification

OF 31

Page 25

PRODUCT GROUP

14.0 PACKING INFORMATION

14.1 Packing order

Put Pad & bottom cover into the box.

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

Put silica gels in the box.

After sealing the box, attach Packing Label on the attach position sign area of the box.

14.2 Notes

zBox Dimension: 333mm(W)X 333mm(D)X 435(H) zPackage Quantity in one Box: 12pcs zTotal Weight : 6.2kg

www.jxlcd.com

Place a cover on the top of the box.

As shown in the figure, place the Modules bundled by shielding bag in the box.

SPEC. NUMBER

S864-1260 25

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 26

PRODUCT GROUP

15.0 MECHANICAL OUTLINE DIMENSION

Figure 6. TFT-LCD Module Outline Dimension (Front View)

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

HT141WX1 0

www.jxlcd.com

SPEC. NUMBER

SPEC TITLE

PAGE

S864-1260 26

B2005-C001-A (3/3) A4(210 X 297)

HT141WX1-101 Product Specification

OF 31

Page 27

PRODUCT GROUP

Figure 7. TFT-LCD Module Outline Dimensions (Rear view)

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

www.jxlcd.com

SPEC. NUMBER

S864-1260 27

B2005-C001-A (3/3) A4(210 X 297)

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

Page 28

16.0 EDID Table

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

Address

(HEX)

00 00 0 0 01 FF 255 255 02 FF 255 255 03 FF 255 255 04 FF 255 255 05 FF 255 255 06 FF 255 255 07 00 0 0 08 09 9 09 E5 229 0A 19 25 0B 05 5 0C 00 0 0D 00 0 0E 00 0 0F 00 0 10 Week of manufacture 0 0 0 11 Year o f M a nufa c ture 0F 15 2005 Manufactured in 2005 12 EDID Structure Ver. 01 1 1 EDID Ver 1.0 13 EDID revision # 03 3 3 EDID Rev. 0.3

www.jxlcd.com

14 Video input definition 80 50 15 Max H image siz e 1E 30 30 30 cm (Approx) 16 Max V ima ge size 13 19 19 19 cm ( Approx) 17 Display Gamma 78 120 2.2 Gam ma curve = 2.2

18 Feature s upport 0A 10 19 Red/Green low bits 62 98 - Red / Gr een Low Bits

1A Blue/White low bits 0 5 5 - Blue / White L ow Bits 1B Red x high bits 95 149 0.583 Red (x) = 10010101 (0.58348) 1C Red y high bits 56 86 0.338 Red (y) = 01010110 (0.33836) 1D Green x high bits 4E 78 0.305 Green (x) = 01001110 ( 0.3 048 2) 1E Green y high bits 8E 142 0.557 Green (y) = 10001110 (0.55656) 1F Blue x high bits 26 38 0.148 Blue (x) = 00100110 (0.14812) 20 BLue y high bits 24 36 0.141 Blue (y) = 00100100 (0.14068) 21 White x high bits 50 80 0.313 White (x) = 01010000 (0.313) 22 White y high bits 54 84 0.329 White (y) = 01010100 (0.329)

www.jxlcd.com

Function Hex Dec values. Notes

Heade r EDID Heade r

ID Ma nuf ac t u rer Na me BOE ID = BOE

ID Product Code 1305 ID = 0519 WXGA

32-bit serial No.

RGB display, Preferred Timmin

mode

SPEC. NUMBER

S864-1260 28

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

B2005-C001-A (3/3) A4(210 X 297)

Page 29

PRODUCT GROUP

(

)

(

)

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

Address

(HEX)

23 Established timing 1 00 0 24 Established timing 2 00 0 25 Established timing 3 00 0 26 01 1 27 01 1 28 01 1 29 01 1 2A 01 1 2B 01 1 2C 01 1 2D 01 1 2E 01 1 2F 01 1 30 01 1 31 01 1 32 01 1 33 01 1 34 01 1 35 01 1 36 C7 199 37 1B 27 38 00 0 1280 Hor Active = 1280 39 A0 160 160 Hor Blanking = 160

3A 50 80 3B 20 32 800 Ver Active = 800

3C 17 23 23 Ver Blanking = 23 3D 30 48 3E 30 48 48 H or Sync Offset = 48

3F 20 32 32 H Sync Pulse Width = 32 40 36 54 3 V sync Offset = 3 line 41 00 0 6 V Sync Pulse width : 6 line

42 2F 47 303 43 BE 190 190 44 10 16 -

45 00 0 0 Hor Border (pixels) 46 00 0 0 Vertical Border (Lines) 47 19 25 -

Function Hex Dec

Standard timing #1 Not Used

Standard timing #2 Not Used

Standard timing #3 Not Used

Standard timing #4 Not Used

Standard timing #5 Not Used

Standard timing #6 Not Used

Standard timing #7 Not Used

Standard timing #8 Not Used

www.jxlcd.com

D etailed timing/monito r

descriptor #1

(60Hz)

values. Notes

71.11 71.11MHz Main clock

4 bits of Hor. Active + 4 bits of Hor.

Blankin

4 bits of Ver. Active + 4 bits of Ver.

Blankin

Horizontal Ima

Verti cal Ima

4 bits of Hor Ima

e Size = 303 mm

Low 8 bits

e Size = 190 mm

Low 8 bits

e Size + 4 bits of

Ver Im a

e Size

SPEC. NUMBER

S864-1260 29

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

B2005-C001-A (3/3) A4(210 X 297)

Page 30

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

Address

(HEX)

48 00 0 49 00 0 4A 00 0 4B FE 0

4C 00 0

4D 0A 0 4E 20 0 4F 20 0 50 20 0 51 20 0 52 20 0 53 20 0 54 20 0 55 20 0 56 20 0 57 20 0 58 20 0 59 20 0 5A 00 0 5B 00 0 5C 00 0 5D FE 0 5E 00 0 5F 42 66 B 60 4F 79 O 61 45 69 E 62 20 32 63 48 72 H 64 59 89 Y 65 44 68 D 66 49 73 I 67 53 83 S 68 0A 10 69 20 32 6A 20 32 6B 20 32

Function Hex Dec

Detailed timing/monitor

descriptor #2

www.jxlcd.com

Detailed timing/monitor

descriptor #3

values. Notes

SPEC. NUMBER

S864-1260 30

SPEC TITLE

HT141WX1-101 Product Specification

PAGE

OF 31

B2005-C001-A (3/3) A4(210 X 297)

Page 31

PRODUCT GROUP

ISSUE DATEREV

2006.04.05ATFT LCD PRODUCT

Addres s

(HEX)

6C 00 0 6D 00 0 6E 00 0 6F FE 254 70 00 0 71 48 72 H 72 54 84 T 73 31 49 1 74 34 52 4 75 31 49 1 76 57 87 W 77 58 88 X 78 31 49 1 79 2D 45 7A 31 49 1 7B 30 48 0 7C 31 49 1 7D 0A 10 7E Extens io n fla g 00 0 7F Checksum 73 115 -

Function Hex Dec values. Notes

Detailed timing/monitor

descriptor #4

Product Name Tag (ASCII)

Model name : HT141WX1-101

www.jxlcd.com

SPEC. NUMBER

SPEC TITLE

PAGE

S864-1260 31

B2005-C001-A (3/3) A4(210 X 297)

HT141WX1-101 Product Specification

OF 31