Biostar P43D3 Owner's Manual

P43D3 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Dichiar azione di co nform ità
sintetica

Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002

Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive

2004/108/CE, 2006/95/CE e
1999/05/CE

quando ad esso applicabili

Short De clar ation of c onform ity

We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives

2004/108/CE, 2006/95/CE and
1999/05/CE

whenever these laws may be applied

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup ..................................... 13

3.1 How to Setup Jumpers .................................................................... 13

3.2 Detail Settings.................................................................................. 13

Chapter 4: Useful Help ............................................................ 18

4.1 Driver Installation Note.................................................................. 18

4.2 Software............................................................................................ 19

4.3 Extra Information............................................................................ 23

4.4 AMI BIOS Beep Code....................................................................... 25

4.5 Troubleshooting............................................................................... 26

Appendix: SPEC In Other Languages ...................................... 27

German.................................................................................................................. 28

French .................................................................................................................... 30

Italian ..................................................................................................................... 32

Spanish ................................................................................................................... 34

Portuguese ............................................................................................................ 36

Polish...................................................................................................................... 38

Russian ................................................................................................................... 40

Arabic..................................................................................................................... 42

Japane se ................................................................................................................ 44

CHAPTER 1: INTRODUCTION

P43D3

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

1

Motherboard Manual

1.3 MOTHERBOARD FEATURES

LGA 775

Intel Core2Duo / Core2Quad /

CPU

FSB 800 / 1066 / 1333 / 1600 MHz (OC) MHz

Chipset

Super I/O

Main

Memory

SATA 2 Integrated Serial ATA Controller

LAN Realtek RTL8111DL

Sound

Codec

Slots

On Board

Connectors

Pent iu m D ua l- Core / C e leron Dual- Core /

Celeron 4xx processor

(Maximum Watt: 125W)

Intel P43

Int e l ICH1 0

ITE 8718F

Prov ides the most common ly used legacy

Super I/O functionality.

Low Pin Count Interface

DIMM Slots x 2

Each DIMM supports 512MB / 1GB / 2GB

DDR3

Max Memory Capacity 4GB

ALC662

PCI Express Gen2 x16 Slot x1 Supports PCI-E Gen2 x16 expansion cards

PCI Express x1 Slot x2 Supports PCI-E x1 expansion cards

PCI Slot x3 Supports PCI expansion cards

Floppy Connector x1 Each connector supports 1 Floppy drive

Printer Port Connector x1 Each connector supports 1 Printer port

SATA Connector x4 Each connector s upports 1 SATA device

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

SPEC

Supports Hyper-Threading / Execute Disable Bit /

Enhanced Intel Sp eedS tep® / Intel Arch itecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

En viro nm en t Co ntrol in it iatives,

Hardware Monitor Controller

Fan Sp eed Contro ller

ITE's "S mart Guard ian " funct ion

Dual Channel Mode DDR3 memo ry mo dule

Supports DDR3 1333(OC) / 1066 / 800

Register ed D IMM and ECC DIMM is not suppo rted

(CPU with FSB 800 MHz only supports DDR3 800)

Data transfer rates up to 3.0 Gb/s.

SATA Vers io n 2 .0 spe c if ic at ion co mp liant

10 / 100 Mb/s / 1Gb/s auto negotiation

Half / Full duplex capability

5.1 channels audio out

High Definition Audio

2

SPEC

S/PDIF out Connector x1 Supports digital audio out function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x1 System Fan Power supply

Clear CMOS Header x 1 Restore CMOS data to factory default

USB Connector x2 Each connector supports 2 front panel US B ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

PS/2 Keyboard x1

PS/2 Mous e x1

Back Panel

I/O

Board Size 182(W) x 295 (L) mm

OS Support Windows 2000 / XP / Vista 32 / Vista 64 / 7

Serial Port x1

LAN port x1

USB Port x4

Audio Jack x3

1.4 R

EAR PANEL CONNECTORS

P43D3

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connects to RS-232 Port

Connect to RJ-45 ethe rnet cab le

Connect to USB devices

Provide Audio-In/Out and microphone connection

Biostar reserves the right to add or remove support for

any OS with or without notice

PS/2
Mouse

LAN

Line In/
Surround

Line Ou t

Mic In 1/
Bass/ Center

P S/2

COM1 USBX2USBX2

Keyboar d

Since the audio chip supports High Definition Audio Specification, the function of each audio
jack can be defined by software. The input / output function of each audio jack listed above
represents the default setting. However, when connecting external microphone to the audio port,
please use the Line In (blue) and Mic In (Pink) audio jack.

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

KBM S 1

LGA775

AT XPW R2

CO M1

CPU_FAN1

USB1

JUSBV1

RJ45USB1

AUDIO1

CPU1

Intel

PEX16_1

P43

AT XPW R1

DDR3_A 1

DDR3_B 1

LAN

PEX1_1

PEX1_2

Super

I/O

CODEC

JSPDIFO UT1

F_AUD IO1

Note: ■ represents the 1st pin.

4

J_PRIN T1

PCI1

PCI2

PCI3

FDD1

BAT1

Intel

ICH10

JCMO S1

JUSBV2

SYS_FAN1

SATA4

SATA3

F_USB2 F_USB1

PAN EL 1

BIOS

SATA 2

SATA 1

CHAPTER 2: HARDWARE INSTALLATION

P43D3

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.

Pin-Cap

Step 1: Pull the socket locking lever out from the socket and then raise

the lever up to a 90-degree angle.

5

Motherboard Manual

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into
the CPU_FAN1. This completes the installation.

6

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different due to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

CPU_FAN1: CPU Fan Header

1

4

SYS_FAN1: System Fan Header

Pin

Assignment

1 Ground
2 Power
3 FAN RPM rate sense
4 Smart Fan Control

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM rate sense

P43D3

13

Note:

CPU_FAN1 supports 4-pin head connec tor; SYS_FAN1, 3-pin head one. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be co nnected to pin#2, and the black wire is Ground and should be connected to
GND.

7

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. DDR3 module

DDR3_B1

DDR3_A1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

8

B. Memory Capacity

P43D3

DIMM Socket

Location

DDR3_A1 256MB/512MB/1GB/2GB

DDR3_B1 256MB/512MB/1GB/2GB

DDR3 Module

Total M emory

Size

Max is 4GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

Disabled O X

Disabled X O

Enabled O O

(O means memory installed; X, not installed.)

The DRAM bus width of the memory module must be the same(x8 or
x16)

DDR3_A1

DDR3_B1

9

Motherboard Manual

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.

234

133

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interface, it
satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

SATA4 SATA2
SATA3 SATA1

147

10

ATXP W R1: AT X Power Source Connector

This connector is for 24-pin power connector on the AT X power supply.

12

24

1

13

P43D3

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

ATXP W R2: AT X Power Source Connector

Connecting this connector provides +12V to CPU power circuit.

12

34

Pin

1 +12V
2 +12V
3 Ground
4 Ground

Assignment

Note:

Before you power on the s ystem, please make sure that both ATXPWR1 and ATXPWR2
connectors have been plugged-in.

11

Motherboard Manual

PCI1~PCI3: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

PCI1

PCI2

PCI3

PEX1_1/PEX1_2: PCI-Express x1 Slot

- PCI-Express 1.1 compliant.

- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the PCI architecture.

12

PEX1 6_1

PEX1_1

PEX1_2

CHAPTER 3: HEADERS & JUMPERS SETUP

P43D3

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

POW_LED

On/Off

-

SPK

++

+

HLED

-

16

8

RS T

9
1

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

3 N/ A 11 N/A N/A

4 Speaker

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

7 Ground 15 Power button

8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

13

Motherboard Manual

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

This motherboard provides 2 USB 2.0 headers, which allows user to connect
additional USB cable on the PC front panel, and also can be connected with
internal USB devices, like USB card reader.

F_USB2 F_USB1

210

Pin Assignment

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 Key

10 NC

19

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB1/RJ45USB1.

JUSBV2: +5V for USB ports at F_USB1/F_USB2.

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB1/RJ45USB1.

JUSBV2: +5V STB for USB ports at F_USB1/F_USB2.

JUSBV1

1

3

13

13

Pin 1-2 close

13

Pin 2-3 close

14

JUSBV2

P43D3

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector, not AC’97.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

10

2

10 Jack Sense

19

JSPDIFOUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Pin

Assignment

1 +5V
2 SPDIF_OUT
3 Ground

13

15

Motherboard Manual

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

2

1

26

25

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7

5 Data 1 18 Ground
6 -Init 19 -ACK

7 Data 2 20 Ground
8 -Scltin 21 Busy
9 Data 3 22 Ground

10 Ground 23 PE
11 Data 4 24 Ground

12 Ground 25 SCLT
13 Data 5 26 Key

16

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

13

13

Pin 1-2 Close:

Normal Operation
(Default).

Pin 2-3 Close:

Clear CMOS data.

13

P43D3

17

Motherboard Manual

CHAPTER 4: USEFUL HELP

4.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/produ cts/acrobat/readstep2.html

18

P43D3

e

4.2 SOFTWARE

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select Software In stallation, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

Before you use this uti lity, please set Outlook Express as your default e-mail client application program.

re pr esen ts i mpor ta nt

*

information that you
must provide. Without
this inf ormation, you may
not be able to send out
the mail.

This bl ock will show
the information which
would be collected in
the mail.

Describe conditi on

*

of your system.

Select your area or

*

the area cl os e to you.

Provide the e-mail
address t hat you would
like to s end the copy to.

Pr ovid e the na me o f

*

the memor y module
manufacturer.

Provide the name of
th e powe r su ppl y
manufacturer and the
model no.

Se nd th e mai l out .

Sav e the se info rmati on to a .t xt fil

Exit this dialog.

19

Motherboard Manual

After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialo g appears asking you to enter file name.

Enter the file name and then click
“Save”. Your system information

will be saved to a .txt file.

20

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php for getting

our contact information.

BIOS Update

BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

P43D3

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Show current BIOS information

Save cur rent BIOS

to a .bin file

Update BIOS

with a BIOS file

<Backup BIOS>

Once click on this button, the saving

dialog will show. Choose t he

position to save file and enter file

name. (We recommend that the file

name should be English/number

and no longer than 7 characters.)

Then click Save.

21

Motherboard Manual

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.

Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being continuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.

22

4.3 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

P43D3

23

Motherboard Manual

BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

24

5. T he utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

parti tion.

z Shutting down or resetting the system while updating the BIOS will lead to

system boot failure.

4.4 AMI BIOS BEEP CODE

Boot Block Beep Codes

Number of Beeps Description

1 No media present. (Insert diskette in floppy drive A:)

2

3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error

7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error

13

POST BIOS Beep Codes

Number of Beeps Description

1 Memory refresh timer error

3 Base memory read/write test error

6 Keyboard controller BAT command failed

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

“AMIBOOT.ROM” file not found in root directory of diskette in
A:

BIOS ROM image mismatch (file layout does not match
image present in flash device)

P43D3

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3 Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.

6, 7

8

z If beep codes are generated when all other expansion

cards are absent, consult your system manufacturer’s
technical support.

z If beep codes are not generated when all other expansion

cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.

If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

25

Motherboard Manual

4.5 TROUBLESHOOTING

Probable Solution

1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work

2. Indicator light on keyboard does
not shine.

System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

System cannot boot after user installs a
second hard drive.

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

26

P43D3

This page is intentionally left blank.

27

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Sp ezif ika tio nen

LGA 775

Intel Core2Duo / Core2Quad /

CPU

FSB 800 / 1066 / 1333 / 1600 MHz (OC) MHz

Chipsatz

Super E/A

Arbeitsspeich

er

Pent iu m D ua l- Core / C e leron Dual- Core /

Celeron 4xx Prozessoren

(Maximales Watt: 125W)

Intel P43

Int e l ICH1 0

ITE 8718F

Biet et die häufig ver wend eten a lten Sup er

E/A-Funktionen.

Low Pin Count-Schnittstelle

DDR3 DIMM-Steckplätze x 2

Jeder DIMM unterstützt 512MB / 1GB / 2GB

DDR3.

Max. 4GB Arbeitsspeicher

Unterstützt Hyper-Threading / Execute Disable Bit /

Enhanced Intel SpeedS tep® / Intel Arch itectur e-64 /

Extended Memory 64 Technology / Virtualization

Technology

Umgebungskontrolle,

Hardware-Überwachung

Lüfterdrehzahl-Controller/-Überwachung

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR3 Speichermodul

Unterstützt DDR3 1333(OC) / 1066 / 800

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

(CPU mit 800 MHz FSB unterstützt nur DDR3-800)

SATA Integrierter Serial ATA-Controller

LAN Realtek RTL8111DL

HD

Audio-Unters

tützung

Steckplätze

ALC662

PCI Express Gen2 x16 Steckplatz x1

PCI Express x1 Steckplatz x2

PCI Stec kp latz x3

28

Datentransferrate b is zu 3.0Gb/s

Konform mit der SATA-Spezifikation Version 2.0.

10 / 100 / 1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

Unterstützt High-Definition Audio

5.1-Kanal-Audioausgabe

Onboard-Ans

chluss

P43D3

Sp ezif ika tio nen

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 1 Diskettenlaufwerke

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

S/PDIF- Ausgangsanschluss x1 Unterstützt die digitale Audioausgabefunktion

CPU-Lüfterstromversorgungsanschluss (mit Smart

CPU-Lüfter-Sockel x1

Fan -F un ktion )

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS lös chen "- So ckel x1

Jeder Anschluss unterstützt 2

USB-Anschluss x2

Fronttafel-USB-Anschlüsse

Stromanschluss (24-polig) x1

St romans ch luss (4- polig ) x 1

PS/2-Tastatur x1

PS/2-Maus x 1

Rückseiten-E

/A

Platinengröße 182mm (B) X 295 mm (L)

OS-Unterstüt

zung

Serieller Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

Windows 2000 / XP / Vista 32 / Vista 64 / 7

Biostar behält sich das Recht vor, ohne Ankündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

29

Motherboard Manual

FRENCH

LGA 775

Processeurs Intel Core2Duo / Core2Quad

UC

Bus frontal 800 / 1066 / 1333 / 1600 MHz (OC) MHz

/ Pentium Du al-Core / Celeron Dual-Core /

Celeron 4xx

(Watt maximum : 125W)

SPEC

Prend en charge les technologies Hyper-Threading /

d'ex écut ion de bit de d ésactivat ion / Inte l SpeedStep®

opt imisé e/ d' arch itectu re In t e l 64 / de m émo ire

étendue 64 / de virtualisation

Chipset

Super E/S

Mémoire

principale

SATA

LAN Realtek RTL8111DL

Prise en

charg e

aud io HD

Fentes

Intel P43

Int e l ICH1 0

ITE 8718F

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Int e rf ace à f a ib le co mpt e de b roches

Fentes DDR3 DIMM x 2

Chaque D IMM p rend en charg e des DDR3

de 512Mo / 1Go / 2Go

Capacité mémoire max imale de 4Go

Contrô leur Serial ATA int é gr é

ALC662

Fente PCI Express Gen2 x16 x1

Fente PCI Express x1 x2

Fente PCI x3

Initiatives de contrôle environnementales,

Mon iteur d e mat ériel

Contrôleur /moniteur de vitesse de ventilateur

Fonction "Gardien intelligent" de l'ITE

Module de mémo ire DDR3 à mod e à doub le voie

Prend en charge la DDR3 1333(OC) / 1066 / 800

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

(UC avec FSB 800 MHz ne prend en charge que DDR3

800)

Taux de transfert jusqu'à 3.0Go/s.

Co nfo rme à la spécif icat ion SATA Vers ion 2.0

10 / 100 / 1000 Mb/s négociation auto matique

Half / Full duplex capability

Prise en charge de l' aud io haute déf init ion

Sortie aud io à 5 .1 voies

30

P43D3

SPEC

Connecteur de disquette x1

Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante

Chaque conne ctor prend en charge 1 lecteu rs de

disquette

Connecteur

embarqué

E/S du

panneau

arrière

Connecteur SATA x4

Chaque co nne cteur pr end en ch arge 1 périphér iqu e

SATA

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

Connecteur de sortie S/PDIF x1 Prend en charge la fonction de sortie audio numérique

Alimentation électrique du ventilateur UC (avec fonction

Embase de vent ilateur UC x1

de ventilateur intelligent)

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Chaque connecteur prend en charge 2 ports USB de

Connecteur USB x2

panneau avant

Connecteur d' aliment at ion x1

(24 broches)

Connecteur d' aliment at ion x 1

(4 broch es)

Clavier PS/2 x1

Souris PS/2 x1

Port série x1

Port LA N x1

Port USB x4

Fiche aud io x3

Dimensions

de la carte

Support SE

182mm (l) X 295 mm (H)

Biostar se réserve le droit d'ajouter ou de supprimer le

Windows 2000 / XP / Vista 32 / Vista 64 / 7

support de SE avec ou sans préavis.

31

Motherboard Manual

ITALIAN

SPECIFICA

CPU

FSB

Chipset

Super I/O

Memoria

principale

LGA 775

Processore Intel Core2Duo /

Core2Quad / Pentium Dual-Core /

Celeron Dual-Core / Celeron 4xx

(Watt massimo : 125W)

800 / 1066 / 1333 / 1600 MHz (OC) MHz

Intel P43

Int e l ICH1 0

ITE 8718F

Fo rn isce le funz ionalit à legacy Super

I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Alloggi DIMM DDR3 x 2

Ciascun DIMM supporta DDR3 512MB

/ 1GB / 2GB

Capacità massima della memoria 4GB

Supporto di Hyper-Threading / Execute Disable

Bit / Enhanced Intel SpeedStep® / Architett ura

Intel 64 / Tecnologia Extended Memory 64 /

Tecnologia Virtualization

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Co ntro ller / Monitoraggio ve locità vent olina

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR3 a canale doppio

Supporto di DDR3 1333(OC) / 1066 / 800

DIMM registrati e DIMM ECC non sono supportati

(CPU con FSB a 800 MHz supporta solo DDR3 800)

SATA

LAN

Supporto

audio HD

Allo ggi

32

Co ntro ller Serial ATA integrat o

Velocità di trasferimento dei dati fino a 3.0Gb/s.

Co mpatibi le s pecifi che SATA Versio ne 2.0.

Negoziazione automatica 10 / 100 / 1000 Mb/s

Realtek RTL8111DL

Capacità Half / Full Dup lex

Supporto audio High-Definition (HD)

ALC662

Uscita audio 5.1 canali

Alloggio PCI Express Gen2 x16 x1

Alloggio PCI Express x1 x2

Allo ggio PC I x3

Connettori

su scheda

P43D3

SPECIFICA

Connettore floppy x1 Ciascun connettore supporta 1 unità Floppy

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

Co nnetto re pannello frontale x 1 Suppo rt a i s erviz i del pan nel lo fron tale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Connettore output SPDIF x1 Supporta la funzione d’output audio digitale

Alimentazione ventolina CPU (con funzione Smart

Co llet tore vent o lina CPU x 1

Fan)

Co llet tore vent o lina sist em a x1 Alimentazio ne ven tol ina d i sistema

Co llet tore cancellaz ione CMOS x1

Ciascun connettore supporta 2 porte USB

Connettore USB x2

pannello frontale

Connettore alimentazione x1

(24 pin)

Connetto re alimentazione x1

(4 pin)

I/O

pannello

posteriore

Dimension

i scheda

Sistemi

oper ativi

supportati

Tas t ier a PS/2 x 1

Mou se PS /2 x1

Porta seriale x1

Porta LA N x 1

Porta USB x 4

Connettore audio x3

182mm (larghezza) x 295 mm

(altez za)

Biostar si riserva il diritto di aggiungere o

Windows 2000 / XP / Vista 32 / Vista

rimuovere il supporto di qualsiasi sistema

64 / 7

operativo senza preavviso.

33

Motherboard Manual

SPANISH

Especificación

CPU

FSB

Conjunto de

chips

Súper E/S

Memoria

principal

LGA 775

Procesador Intel Core2Duo / Core2Quad /

Pent iu m D ua l- Core / C e leron Dual- Core /

Celeron 4xx

(Vatio máximo: 125W )

800 / 1066 / 1333 / 1600 MHz (OC) MHz

Intel P43

Int e l ICH1 0

ITE 8718F

Le ofrece las funcionalidades heredadas de

us o más comú n Súper E/S.

Interfaz de cuenta Low Pin

Ranuras DIMM DDR3 x 2

Cada DIMM admite DDR de 512MB / 1GB /

2GB

Capacidad máxima de memoria de 4GB

Admite Hyper-Threading / Bit de deshabilitación de

ejecución / Inte l SpeedStep® Mejorado / Intel

Architecture-64 / Tecnología Extended Memory 64 /

Tecnología de virtualización

In ic iativas de co ntr ol de en tor no ,

Monitor hardware

Controlador/monitor de velocidad de ventilador

Función "Guardia inteligente" de ITE

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 1333(OC) / 1066 / 800

No admite DIMM registrados o DIMM compatibles con

ECC (CPU con FSB de 800 MHz sólo soporta DDR3 800)

SATA

Red Local

Soporte de

sonido HD

Ranuras

34

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 3.0 Gb/s.

Co mpat ible co n la ve rsión SATA 2 .0 .

Negociación de 10 / 100 / 1000 Mb/s

Realtek RTL8111DL

Funciones Half / Full dúplex

Soporte de sonido de Alta Definición

ALC662

Salida de sonido de 5.1 canales

Ranura PCI Express Gen2 x16 X1

Ranura PCI express x1 X2

Ranura PCI X3

P43D3

Especificación

Conector disco flexible X1 Cada conector soporta 1 unidade de disco flexible

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Conector SATA X4 Cada conector soporta 1 dispositivos SATA

Co nect or de p an el f ro nta l X1 So porta inst a lacion es en e l p anel fro nta l

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Conector de salida S/PDIF X1 Soporta función de salida de sonido dig ital

Conectores

en p laca

Panel

trasero de

E/S

Ta mañ o de

la placa

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de s istema

Cabecera de borrado de CMOS X1

Conector USB X2 Cada conector s oporta 2 puertos USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Tec lad o P S /2 X 1

Ratón PS/2 X1

Puert o s er ie X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X3

182mm. (A) X 295 Mm. (H)

Soporte de

sistema

operativo

Windows 2000 / XP / Vista 32 / Vista 64 / 7

Biostar se reserva el derecho de añadir o retirar el

soporte de cualqu ier SO con o sin aviso previo.

35

Motherboard Manual

PORTUGUESE

LGA 775

ESPECIFICAÇÕES

CPU

FSB

Chipset

Especificaçã

o Super I/O

Memória

principal

Processador Intel Core2Duo / Core2Qu ad

/ Pentium Du al-Core / Celeron Dual-Core /

Celeron 4xx

(Watt máx imo: 125W)

800 / 1066 / 1333 / 1600 MHz (OC) MHz

Intel P43

Int e l ICH1 0

ITE 8718F

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Interface LPC (Low Pin Count).

Ranhuras DIMM DDR3 x 2

Cada módulo DIMM suporta uma

memória DDR3 de 512 MB / 1GB / 2GB

Capacidade máx ima de memória:4GB

Sup orta as tecno logias Hyper-Thread ing / Ex ecut e

Disab le Bit / Enh anced Intel SpeedStep® / Intel

Arquitecture -64 / Extended Memory 64 / Virtualization

In ic iativas par a cont ro lo d o ambiente

Monitorização do hardware

Controlador/Monitor da velocidade da ventoinha

Função "Smart Guardian" d a ITE

Módulo de memória DDR3 de canal duplo

Suporta módulos DDR3 1333(OC) / 1066 / 800

Os módulos DIMM registados e os DIMM ECC não são

suportados

(CPU com FSB 800 MHz só suporta DDR3 800)

SATA

LAN

Suporte

para áudio

de alta

definição

Ranhuras

36

Controlador Serial ATA integrado

Velocidades de transmissão de dados até 3.0 Gb/s.

Compat ibilidad e co m a espe cificação SATA ve rsão 2.0.

Auto negociação de 10 / 100 / 1000 Mb/s

Realtek RTL8111DL

Capacidade semi/full-duplex

Suporta a especificação High-Definition Audio

ALC662

Saída de áudio de 5.1 canais

Ranhura PCI Express Gen2 x16 x1

Ranhura PCI Express x1 x2

Ranhura PCI x3

Conectores

na placa

P43D3

ESPECIFICAÇÕES

Conector da unidade de disquetes x1 Cada conector suporta 1 unidade de disquete

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Conector SATA x4 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áudio frontal x 1 Suporta a função de áudio no painel fro ntal

Conector de sa ída S/PDIF x1 Suporta a saída de áudio digital

Aliment ação d a ventoinha d a CPU (co m a função S mart

Conector da ventoinha da CPU x1

Fan )

Conector da ventoinha do s istema x1 Alimentação da vento inha do sistema

Conector para limpeza do CMOS x1

Conector USB x2 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Entradas /S

aídas no

painel

traseiro

Tamanho

da placa

Sistemas

operativos

suportados

Conector de alimentação x1

(4 p inos )

Tec lad o P S /2 x 1

Rato PS/2 x1

Porta série x 1

Porta LA N x1

Porta USB x 4

Tomada de áudio x3

182mm (L) X 295 mm (A)

Windows 2000 / XP / Vista 32 / Vista 64 / 7

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av iso p révio.

37

Motherboard Manual

POLISH

SPEC

Procesor

FSB

Chipset

Pamięć

główna

Super I/O

LGA 775

Procesor Intel Core2Duo / Core2Quad /

Pent iu m D ua l- Core / C e leron Dual- Core /

Celeron 4xx

(Maksymalny Watt: 125W)

800 / 1066 / 1333 / 1600 MHz (OC) MHz

Intel P43

Int e l ICH1 0

Gniazda DDR3 DIMM x 2

Każde gniazdo DIMM obs ługuje moduły

512MB / 1GB / 2GB

Maks. wielkość pamięci 4GB

ITE 8718F

Zapewn ia najbardziej powszechne funkcje

Super I/O.

Interfejs Low Pin Count

Obsługa Hyper-Threading / Execute D isable Bit /

Enhanced Intel Sp eedS tep® / Intel Arch itecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

Mod uł pamięci DDR3 z trybem podwójnego kanału

Obsługa DDR3 1333(OC) / 1066 / 800

Brak obsług i Registered DIMM oraz ECC D IMM

(CPU z FSB 800 MHz tylko obsługuje pamięci DDR3 800)

Funkcje kontroli warunków pracy,

Mon itor H /W

Kontroler/Monitor prędkości wentylatora

Funkcja ITE "Smart Guardian"

SATA

LAN

Obsługa

aud io HD

Gniazda

38

Zintegrowany kontroler Serial ATA

Realtek RTL8111DL

ALC662

Gniazdo PCI Express Gen2 x16 x1

Gniazdo PCI Express x1 x2

Gniazdo PCI x3

Transfer danych do 3.0 Gb/s.

Zgodność ze specyfikacją SATA w wersj i 2. 0.

10 / 100 / 1000 Mb/s z automatyczną negocjacją

szybkości

Działanie w trybie połowicznego / pełn ego dupleksu

Obsługa H igh- Defin ition A udio

5.1 kanałowe wyjście audio

SPEC

Złącze napędu dyskietek x1 Każde złącze obs ługuje 1 napędy dyskietek

Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki

Złącze SATA x4 Każde złącze obs ługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie z łącze aud io x1 Obsługa funkcji audio na panelu przednim

Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia aud io

P43D3

Złącza

wbud owan e

Back Panel

I/O

Wymiary

płyty

Obsluga

systemu

operacyjne

go

Złącze głó wko we wenty latora

procesora x1

Złącze głó wko we wenty latora

systemowego x1

Złącze głó wkowe kasowan ia CMOS x 1

Złącze USB x2

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x 1

Klawiatura PS/2 x1

Mys z PS /2 x1

Port sz erego wy x1

Port LA N x1

Port USB x4

Gniazdo audio x3

182mm (S) X 295 mm (W)

Windows 2000 / XP / Vista 32 / Vista 64 / 7

Zasilanie wentylatora procesora (z funkcją Smart Fan)

Zasilanie wentylatora systemowego

Każde złącze obs ługuje 2 porty USB na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływania obs ług i dowo lneg o systemu

operacyjnego b ez powiado mienia.

39

Motherboard Manual

RUSSIAN

LGA 775

CPU

(центральн

ый

процессор)

FSB

Набо р

микросхем

Основная

память

Super I/O

SATA

Локальна я

сеть

Звуко вая

поддержка

жестког о

диска

Слоты

Процессор Intel Core2Duo / Core2Quad /

Pent iu m D ua l- Core / C e leron Dual- Core /

Celeron 4xx

(Макси мальный ватт: 125W)

800 / 1066 / 1333 / 1600 (OC) МГц

Intel P43

Int e l ICH1 0

Слоты DDR3 DIMM x 2

Каждый модуль DIMM поддерживает

512МБ / 1ГБ / 2ГБ DDR3

Максимальная ёмкость памяти 4ГБ

ITE 8718F

Обеспечивает наиболее используемые

действующие фун кц и онал ьные

возможно сти Super I/O.

Интерфейс с ни зким количеством

выводов

Встроенное послед оват ельное

устройс тво управлен ия ATA

Realtek RTL8111DL

ALC662

Слот PCI Express Gen2 x16 x1

Слот PCI Express x1 x2

Слот PCI x3

СПЕЦ

Поддержка технологий Hyper-Threading / Execute

Disab le Bit / Enh anced Intel SpeedStep® / Intel

Architecture-64 / Extended Memory 64 Technology /

технологии виртуализац ия

Мод ул ь памяти с двух канальн ым режимом DDR3

Поддержка DDR3 1333(OC) / 1066 / 800

Не поддерживает зарегистрированн ые модули

DIMM and ECC DIMM

(Процессор с ФС Б 800 МГц поддерживает только

DDR3 800)

Инициативы по охране окружающей среды,

Аппаратный монитор

Регул ятор скорости вентил ятора/ монитор

Функция ITE "S mart Guard ian" (Интеллектуальная

защит а)

скорость передачи данных до 3.0 гигабит/с.

Соответствие специ фикации SATA версия 2.0.

Автоматическо е согласо вани е 10 / 100 / 1000 Мб/с

Частичная / полна я дуплексная способность

Звуко вая поддержка High-Defin it ion

5.1канальный звуковой выхо д

40

Встроенны

й разъём

Задняя

панель

средств

ввода-выв

ода

Разм ер

панели

Поддержка

OS

P43D3

СПЕЦ

Разъ ём НГМД x1

Разъ ём Порт подклю чения

принтера x1

Разъ ём SATA x4 Каждый разъём поддерживает 1 устройство SATA

Разъ ём на лицевой панели x1 Поддержка устройс тв на лицевой панели

Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели

Разъ ём вывода для S/PDIF x1 Поддержка вывода цифровой звуковой функ ции

Контактирующее приспособление

вентил ятора центрального процессора

x1

Контактирующее приспособление

вентил ятора системы x1

Открытое контактирующе е

приспособление CMOS x1

USB- разъём x2

Разъ ем питания (24 вывод) x1

Разъ ем питания (4 вывод) x1

Клавиатура PS/2 x1

Мышь PS /2 x1

Последо вательны й порт x1

Пор т LAN x1

USB- порт x4

Гнездо для подключени я

наушников x3

182мм (Ш) X 295 мм (В)

Windows 2000 / XP / Vista 32 / Vista 64 / 7

Каждый разъём поддерживает 1 накопителя на

гибких магнитных дисках

Каждый разъём поддерживает 1 Порт подключения

принтера

Источник пит ания для вентилятор а центрального

процессора (с функц ией интеллектуального

вентил ятора )

Источник пит ания для вентилятор а системы

Каждый разъём поддерживает 2 USB-порта на

лицевой панели

Biostar сохраняет за собой право добавлять или

удаля ть средства обеспечения для OS с или без

предварительного уведомления.

41

Motherboard Manual

ARABIC

تﺎﻔﺻاﻮﻤﻟا

تﺎﻴﻨﻘﺗ ﻢﻋﺪﺗHyper-Threading / Execute Disable Bit /

Enhanced Intel Sp eedStep® / Intel Arch itecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

ةﺮآاذ ةﺪﺣوDDR3 ﻘﻟا ﺔﺝودﺰﻣةﺎﻨ

عﻮﻥ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 تﺎﻌﺳ 800 / 1066 /1333)OC(ﺖیﺎﺑ ﺎﺠﻴﻣ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻣ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠ ﺗو ECC

(800 ﺰﺗﺮهﺎﺠﻴﻣ ﻊﻣ ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا ﺔیﺰآﺮﻤﻟا ﺰﺗﺮﻴهﺎﻐﻴﻣ ﻂﻘﻓ ﻢﻋﺪﺗ

DDR3 800)

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻣ

ﺔﻔﻴﻇو"S mart Gu ardian" ﻦﻣ ITE

تﺎﺠﻟﺎﻌﻣIntel Core2Duo / Core2Quad /

Pent iu m D ua l- Core / C e leron Dual- Core /

ددﺮ ﺗ 800 / 1066 / 1333 / 1600 (OC) ﺰﺗﺮه ﺎﺠﻴﻣ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﻞآ ﻢﻋﺪﺗ ﺔﻌﺳ

ﺔﺤﺘﻓDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﺔﻌﺳ

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻣ ا ﺪ ﺨﺘﺳ ا ﺮﺜآﻷا .

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pin Count Interface

LGA 775

Celeron 4xx ﺑ ددﺮﺘ ی ﻰﻟإ ﻞﺼ

(طاو ىﻮﺼﻗ: 125و)

Intel P43

Int e l ICH1 0

ﺔﺤﺘﻓDDR3 DIM M دﺪﻋ2

512 ﺖیﺎﺑ ﺎﺠﻴﻣ

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ4 ﺖیﺎﺑ ﺎﺠﻴﺝ

ITE 8718F

ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا

ﺔیﺰآﺮﻤﻟا

ﻞﻗﺎﻨﻟا ﻲﻣﺎﻣﻷا ﻲﺒﻥﺎﺠﻟا

ﺔﻋﻮﻤﺠﻣ ﺢﺋاﺮﺸﻟا

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

و1/و 2 ﺎﺠﻴﺝﺖیﺎﺑ

Super I/O

42

ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎﻋﺮﺴﺑ ﻞﺼ ﺗ ﻰﻟإ 3.0 ﺖﺑﺎﺠﻴﺝ/ﺔﻴﻥﺎﺙ.

ﺔﻘﺑﺎﻄﻣ تﺎﻔﺹاﻮﻤﻟ SATA راﺪﺹﻹا 2.0.

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100 ﺖیﺎﺑ ﺎﺠﻴﻣ /و ﺔﻴﻥﺎﺙ1ﺖﺑ ﺎﺠﻴﺝ/ﺔﻴﻥﺎﺙ

ﻞﻣﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻣإ/ﻲﻔﺼﻨﻟا

ﻘﺗ ﻢﻋﺪﺗ ﻦﻣ ﻒیﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨ

5.1 تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ﺔﺤﺘﻓGen2 x16 PCI Express دﺪﻋ1

ﺔﺤﺘﻓPCI Express x1 دﺪﻋ2

ﺔﺤﺘﻓPCI ﺪﻋ3

ﻢﻜﺤﺘﻣ Serial ATA ﻞﻣﺎﻜﺘﻣ

Realtek RTL8111DL

ALC662

SATA

ﺔﻜﺒﺷ ﺔﻴﻠﺧاد

ﻢﻋد تﻮﺼﻟا ﻲﻟﺎﻋ

ﻒیﺮﻌﺘﻟا

تﺎﺤﺘﻔﻟا

تﺎﻔﺻاﻮﻤﻟا

P43D3

ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآﺮﺤﻣ ﻢﻋﺪی

ﺑﺎﻃ ﺬﻔ ﻨﻣﺔﻌ دﺪﻋ1

ةﺰﻬﺝأ ﻦﻣ ﺪﺣاو ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیSATA

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪی

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟ ﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇ و ﻢﻋﺪی

ﻲﻤﻗﺮﻟا تﻮﺼﻟا جﺮﺥ ﺔﻔﻴﻇو ﻢﻋﺪی

ﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ ﺔﻔﻴﻇو ﻊﻣ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔ Smart Fan

مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄ ﻟا ﻞﻴﺹﻮﺘﻟ

ﺢﺴ ﻣ ﺔﻠﺹوCMOS دﺪﻋ1

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیUSBﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ)24سﻮﺑد( ع دد1

ﻔﻨﻣ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬ)4ﺲﻴﺑﺎﺑد( دﺪﻋ1

ﺔﻥﺮﻣ صاﺮﻗأ كﺮﺤﻣ ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻔﻨﻣSATA دﺪﻋ4

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻣ دﺪﻋ1

ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ دﺪﻋ1

جﺮﺥ ﺬﻔﻨﻣS/PDIF دﺪﻋ1

ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻣ ﺔﻠﺹو دﺪﻋ1

ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄ ﺳ

ﺔﺣﻮﻠﻟا

مﺎﻈﻨﻟا ﺔﺣوﺮﻣ ﺔﻠﺹو دﺪﻋ1

ﺬﻔﻨﻣUSB دﺪﻋ2

ﺢﻴﺗﺎﻔﻣ ﺔﺣﻮﻟPS/2 دﺪﻋ1

سوﺎﻣ PS/2 دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻣ دﺪﻋ1

ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻣ ﺪﻋ1

ﺬﻓﺎﻨﻣ ﻞﺧد/جﺮﺧ

ﺔﺣﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا

ﺬﻓﺎﻨﻣUSB دﺪﻋ4

ﻆﻔﺘﺤﺗ Biostar ﺎﻬﻘﺤﺏ ﻲﻓ ﺿإﺔﻓ ﺎ وأ ﺔﻟازإ ﻢﻋﺪﻟا يﻷ مﺎﻈﻥ ﻞﻴﻐﺸﺗ رﺎﻄﺧﺈﺏ وأ نوﺪﺏ

تﻮﺹ ﺲﺒﻘﻣ دﺪﻋ3

182 ﻢﻣ)ضﺮﻋ (X 295 ﻢﻣ)عﺎﻔﺗرا( ﻢﺠﺣ ﺔﺣﻮﻠﻟا

Windows 2000 / XP / Vista 32 / Vista 64 / 7

رﺎﻄﺧإ.

ﻢﻋد ﺔﻤﻈﻥ أ ﻞﻴﻐﺸﺘﻟا

43

Motherboard Manual

JAPANESE

仕様

CPU

FSB

チップセット

メインメモリ

Super I/O

LGA 775

Intel Core2Duo / Core2Quad /

Pent iu m D ua l- Core / C e leron Dual- Core /

Celeron 4xx processor

(最高のワット: 125W)

800 / 1066 / 1333 / 1600 MHz (OC) MHz

Intel P43

Int e l ICH1 0

DDR3 DIMMスロット x 2

各DIMMは 512MB / 1GB / 2GB DDR3をサ

ポート

最大メモリ容量4GB

ITE 8718F

もっとも一般に使用されるレガシーSuper I/O

機能を採用しています。

Hyper-Threading / Execute D isab le Bit / Enhanced Intel

SpeedStep® / Intel Ar ch itecture-64 / Ex tended

Memory 64 Technology / V irtualization Technologyをサ

ポートします

デュアル チャンネルモードDDR3メモリモジュール

DDR3 1333(OC) / 1066 / 800をサポート

登録済みDIMMとECC D IMMはサポートされません

(のCPUのFSBを800 MHzの唯一のDDR3 800をサポートし

ています)

環境コントロールイニシアチブ、

H/Wモニター

ファン速度コントローラ/ モニター

低ピンカウントインターフェイス

SATA 統合シリアルATA コントローラ

LAN Realtek RTL8111DL

HDオーディ

オのサポート

スロット

ALC662

PCI Express Gen2 x16スロット x1

PCI Express x1スロット x2

PCIスロット x3

44

ITE の「スマートガーディアン」機能

最高3.0 Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

10 / 100 / 1000 Mb/秒のオートネゴシエーション

半/全二重機能

ハイデフィニションオーディオのサポート

5.1 チャンネルオーディオアウト

P43D3

仕様

フロッピーコネクタ x1 各コネクタは1つのフロッピードライブをサポートします

プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします

SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします

フロントパネルコネクタ x1 フロントパネル機能をサポートします

フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします

オンボードコ

ネクタ

背面パネル

I/O

ボードサイズ

OSサポート W indows 2000 / XP / Vista 32 / Vista 64 / 7

S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします

CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)

システムファンヘッダ x1 システムファン電源装置

CMOSクリアヘッダ x1

USBコネクタ x2

電源コネクタ(24 ピン) x 1

電源コネクタ(4ピン) x1

PS/2キーボード x1

PS/2マウス x1

シリアルポート x1

LANポート x1

USBポート x4

オーディオジャック x3

182mm (幅) X 295 mm (高さ)

各コネクタは2つのフロントパネルUSBポートをサポートし

ます

Biostarは事前のサポートなしにOSサポートを追加または削

除する権利を留保します。

2011/05/20

45