APPLE INC.
NONE
SCALE
REV.
A
D
C
B
A
D
C
B
8 7
6
5
4
3
2 1
8
7 6
5
4
3
2
1
THE INFORMATION CONTAINED HEREIN IS THE PROPRIETARY
PROPERTY OF APPLE COMPUTER, INC. THE POSSESSOR
AGREES TO THE FOLLOWING
II NOT TO REPRODUCE OR COPY IT
III NOT TO REVEAL OR PUBLISH IN WHOLE OR PART
I TO MAINTAIN THE DOCUMENT IN CONFIDENCE
NOTICE OF PROPRIETARY PROPERTY
DRAWING NUMBER
SHT
OF
SIZE
D
- ALL 128S0122 BECOME 128S0157.
- ALL 128S0115 BECOME 128S0150.
- ADD ISOLATION BUFFER FOR ODD_RESET_L SIGNAL, ADD 100K PULL-DOWN TO ODD_PWR_EN_L, ADD ’DRAG’ CIRCUIT TO
- LOWER RDS(ON) MOSFET (FDC606P - APN: 376S0552) FOR ODD AND LCD POWER - RADAR: TBD
- HIGH-PRECISION 0.1% RESISTORS TO INCREASE OUTPUT VOLTAGE REGULATION (5V, 3.3V, PBUS_LDO) ACCURACY - RADAR:4972500
- FIX LINDA CARD POWER ALIAS (NEED TO CONNECT TO PP3V42_G3HOT INSTEAD OF PP3V3_S5) - RADAR: 4927858
- CHANGE BOM STUFFING TO SPEED UP PORT POWER SHUT-OFF RESPONSE TIME DURING ACTIVE LATE-VG EVENT (RADAR: 4985252)
- CHANGE BOM STUFFING TO ENABLE ON-BOARD MICROPHONE CONNECTOR (M42/M42A SOLUTION) INSTEAD OF ROUTING
- CHANGE BEST CPU FROM 337S3465(2.4GHZ) TO 337S3464(2.2GHZ).
- ADD BOM OPTION TABLE FOR ALL SANYO POSCAP TO USE HF PARTS.
CSA PAGE 4:
- ADD OMIT TO ALL ABOVE PARTS SO THE HF PARTS IN BOM TABLE TAKE OVER.
- ALL 128S0129 BECOME 128S0135.
- ALL 128S0123 BECOME 128S0162.
- ALL 128S0113 BECOME 128S0160.
- ALL 128S0111 BECOME 128S0169.
- ALL 128S0085 BECOME 128S0148.
- ALL 128S0073 BECOME 128S0164.
- ALL 128S0057 BECOME 128S0147.
PER CE, ALL SANYO POSCAPS HAVE NEW HF PART NUMBERS.
8/9/2007
M70 EVT TO DVT CHANGES
M70 EVT TO DVT CHANGES
- TEST POINT MOVEMENTS REQUESTED BY ICT AND MAC-1 GROUPS - RADAR: 4924481
- MODIFY FIREWIRE CONNECTOR SYMBOL TO SUPPORT MINI-DVI CONNECTOR WITH TAB
- CHANGE 10UF, 16V CPU VCORE CAPS TO 10UF, 6.3V CAPS - RADAR: 4952553
- CHANGE LOAD CAP STUFFING OPTION FOR RTC AND ETHERNET CRYSTALS TO MEET 5XESR (-R) REQUIREMENT
PROPERLY DISCHARGE ODD POWER WHEN IT’S TURNED OFF - RADAR: 4923903
M70 PROTO TO EVT CHANGES
- ADD 270K PULL-DOWN RESISTOR ON HTPLG - RADAR: 4888755
- MOVE SMC RESET BUTTON PAD TO TOP SIDE OF MLB - RADAR: 4920913
CSA PAGE 8:
- 4954357 BREAK OUT =PP3V3_S3_AIRPORT_AUX(J3400,PIN 24) FROM PP3V3_S3_AP_AUX AGAIN.
- 4954357 MOVE C3409 AND C3410 FROM PP3V3_S3_AP_AUX RAIL TO =PP3V3_S3_AIRPORT_AUX RAIL.
- NORMAL CHANGES FROM 514-0409 TO 514-0459, FANCY CHANGES FROM 514-0411 TO 514-0479.
- CHANGE J6750 FROM 514-0408 TO 514-0458 (DIFFERENT JEDEC, SAME LANDPATTERN).
- UPDATE BOM OPTION TABLE FOR J6750.
- NORMAL CHANGES FROM 514-0408 TO 514-0458, FANCY CHANGES FROM 514-0410 TO 514-0478.
- CHANGE J6700 FROM 514-0409 TO 514-0459 (DIFFERENT JEDEC, SAME LANDPATTERN).
- CHANGE R9201 AND R9202 FROM 5.23K TO 2.94K.
- NORMAL CHANGES FROM 514-0375 TO 514-0480, FANCY CHANGES FROM 514-0376 TO 514-0481.
- CHANGE L7900 FROM 152S0302 TO 152S0670 FOR CORRECT AVL.
- SMC PART NUMBER CHANGES FROM 341S2088 TO 341S2198.
CSA PAGE 29:
- ADD ALIAS =PP3V3_S3_SMBUS_SMC_MGMT TO PP3V3_S3.
- UPDATE EEE CODES, Z55 FOR GOOD, Z56 FOR BETTER, Z57 FOR BEST.
CSA PAGE 32:
- STUFF C3110 AND C3111.
CSA PAGE 31:
CSA PAGE 9:
- FIX MOJO-CARD SMC TX, RX REVERSAL - RADAR: 4910888
CSA PAGE 90:
- CHANGE SB FROM 338S0427 TO 338S0434.
- CHANGE J3900 FROM 514S0143 TO 514-0443.
- REMOVE NO_TEST=TRUE FOR 1V8S3_COMP, 1V8S3_FSET, 3V3S5_COMP, 3V3S5_FSET, 1V05S0_COMP, 1V05S0_FSET, IMVP6_RBIAS, IMVP6_COMP, 5VS5_RUNSS, 1V5S0_RUNSS.
- REMOVE ALIASES FOR GND_CHASSIS_AUDIO_SPKRCONN,GND_CHASSIS_AUDIO_SHIELD1,GND_CHASSIS_AUDIO_SHIELD2,GND_CHASSIS_AUDIO_SHIELD3,MIC_SHIELD_LVDS_R,MIC_SHLD_CONN.
- ADD FUNC_TEST=TRUE FOR THRM_FINSTACK_P/N.
7/6/2006
- CHANGE U5500 FROM M70 EMC1033 CIRCUIT TO M71 EMC1043 CIRCUIT.
- CHANGE J4810 FROM 518S0369 TO 518S0521.
- CHANGE C2700 FROM 128S0051 TO 128S0113 PER CE.
7/5/2006
- CHANGE R2514 TO 100K.
CSA PAGE 29:
- RENAME CPU_VID_R<6:0> TO CPU_VID<6:0>.
CSA PAGE 71:
- ADDED R6856 NO STUFF.
- CONNECTED MIC_SHLD_CONN TO GND_CHASSIS_AUDIO_MIC THROUGH R6854.
CSA PAGE 68:
- ADDED R6740 NO STUFF.
- REMOVED DZ6772.
- ADDED L6771 AND L6773 TO MIC INPUT EMI FILTER.
- CHANGED ALL TRANSIENT SUPPRESSORS TO 6.8V/100PF DEVICES (WERE ORIGINALLY 8V/100PF DEVICES).
CSA PAGE 67:
- ADDED SMALL 15PF COMPENSATION CAP. TO U6201 FEEDBACK NETWORK (C6224).
- ADDED A NO STUFF PULL-UP TO CODEC_DVDD AT GPIO1.
- RE-CONNECTED /SHDN INPUT OF U6801 SO THAT IT’S CONTROLLED BY U6200 PORTA VREF. - DISCONNECTED GPIO1 AND TERMINATED IT WITH A 10K PULL DOWN.
CSA PAGE 62:
- RE-DRAW CPU VOLTAGE SENSE RC FILTERING.
CSA PAGE 53:
- REMOVE TEXT NOTE WILL CHANGE TO 606P.
CSA PAGE 44:
- CHANGE R2902 FROM 1OHM TO 0OHM.
- CHANGE R2900, R2901 FROM 2.2OHM TO 0OHM.
- NOSTUFF C2907, C2910, C2916, C2911, C2914.
- CHANGE L2902 AND L2903 FROM 155S0302 TO 0OHM R2906 AND R2907.
- ADD R2597 AND R2596 FOR 10K PU ON GPIO6 AND GPIO17(EXTGPU_RST_L).
CSA PAGE 25:
- RENAME LVDS_VREFH/L TO TP_LVDS_VREFH/L.
CSA PAGE 15:
- DELETE TEXT NOTE AND WITH RESET BUTTON.
CSA PAGE 13:
- REMOVE R1290 TO R1296 ON CPU_VID<0:6>.
CSA PAGE 12:
- ADD SPN ALIASES FOR CK505_PCI2/4_CLK.
- ADD SPN ALIASES FOR TP_CK505_SRC7_N/P.
- REMOVE ALIAS FOR =FWPWR_PWRON.
CSA PAGE 9:
- ADD FUNC_TEST=TRUE FOR PP1V05_S0_R.
- REMOVE NO_TEST=TRUE FOR CK505_PCI4_CLK_SPN, CK505_SRC1_N/P_SPN, CK505_SRC3_N/P_SPN, CK505_SRC7_N/P_SPN, CK505_SRC_CLKREQ1/3_L?SPN.
CSA PAGE 8:
- CHANGE J9000 FROM 518S0369 TO 518S0521.
CSA PAGE 90:
- CHANGE J6703 FROM 518S0369 TO 518S0521.
- CHANGE J6702 FROM 518S0487 TO 518S0519.
CSA PAGE 67:
- CHANGE J5601 FROM 518S0369 TO 518S0521.
CSA PAGE 56:
- J5550 CHANGES FROM 2PIN TO 4PIN.
CSA PAGE 55:
CSA PAGE 48:
6/29/2007
M70 DVT TO K36 CHANGES
- REMOVE R4660 AND R4601 (U4675 BYPASS RESISTORS).
CSA PAGE 46:
- CHANGE J2800 FROM 518S0487 TO 518S0519.
CSA PAGE 28:
CSA PAGE 27:
- CHANGE C2173 FROM 128S0051 TO 128S0113 PER CE.
CSA PAGE 21:
- REPLACE ALL M70 WITH K36 (TEXT, BOM OPTIONS, 630 NUMBERS).
CSA PAGE 4:
- 5040728 CHANGE L9404 FROM 155S0303 TO 155S0348.
CSA PAGE 94:
- REPLACE BATTERY INTERFACE CIRCUIT WITH THE ONE ON M42B ESTAR.
- CHANGE J6900 FROM 518S0287 TO 518S0526.
CSA PAGE 69:
- CHANGE J4700 FROM 516S0251 TO 516S0588.
CSA PAGE 47:
- ADD NOSTUFF R4660 AND R4661.
- REMOVE MIN_NECK_WIDTH=0.3MM FROM PP5V_S3_USB2_EXTA/B.
- CHANGE U4600 FROM 353S1245 TO 353S1728.
CSA PAGE 46:
- EDIT BOM OPTION TABLE.
CSA PAGE 39:
- CHANGE STRAPPING FROM 0010 ON GFX_VID<1:4> TO 0001 ON GFX_VID<0:3>.
- CHANGE GFX_VID<1:4> TO GFX_VID<0:3>.
- SIZING DOWN R2205 FROM 0603 TO 0402 FOR PLACEMENT.
- 5282756 ADD C2207 (0.1UF, 0402).
CSA PAGE 22:
- ADD R1600 (0OHM, 0402) TO CONNECT GFX_VID<4> TO GND.
- CONNECT GFX_VID<0:3> TO GFX_VID0:3 ON NB.
- DISCONNECT GFX_VID<0> TO GND.
CSA PAGE 16:
- CHANGE NB FROM 338S0426(500M) TO 343S0448(667M).
- CHANGE BEST CPU FROM 337S3457(2.2G) TO 337S3465(2.4G).
- CHANGE BETTER CPU FROM 337S3456(2.0G) TO 337S3464(2.2G).
- CHANGE GOOD CPU FROM 337S3471(1.8G) TO 337S3463(2.0G).
CSA PAGE 4:
CSA PAGE 49:
- 5040728 STUFF C9421 FOR EMI.
3/5/2007
- 5048817 SYNC 1P25V REGULATOR CIRCUIT FROM M82, CHANGE R AND C TO 0402, CHANGE =PP3V3_S5_P1V25S0 TO =PP3V3_S5_1V25S0,
C7723 FROM 2.2NF TO 10000PF, C7724 FROM 22PF TO 100PF, C7728 FROM 2.2NF TO 10000PF,
AND REVERT REFERENCE DESIGNATORS. (CHANGE FROM TPS62510 TO LTC3412A)
3/12/2007
- 4924443 CHANGE R2514 FROM 100K PULL-UP TO 47K PULL-UP.
CSA PAGE 45:
- 4924443 CHANGE R2514 FROM 100K PULL-DOWN TO 10K PULL-UP TO 3.3V_S5.
- 4986074 CHANGE L2205 TO R2205(100OHM,5%,1/10W,0603).
CSA PAGE 69:
- ADD TEXT NOTE TO UPDATE J4700 FROM 516S0251 TO 516S0588 WHEN SYMBOL IS READY.
- 4986074 CHANGE R9469 FOR CRT_TVO_IREF FROM 1.3K TO 1.21K.
- ADD TEXT NOTE TO UPDATE J6900 FROM 518S0287 TO 518S0526 WHEN SYMBOL IS READY.
- DELETE LVDS_VREFH AND LVDS_VREFL TO GROUND TO FIX LVDS GLITCH.
- ADD TEXT NOTE TO CHANGE L9404 FROM 155S0303 TO 155S0348 WHEN SYMBOL IS READY.
CSA PAGE 77:
- SYNC FROM AUDIO TEAM.
3/14/2007
CSA PAGE 47:
CSA PAGE 94:
CSA PAGE 79:
- UPDATE SYMBOL FOR J4501.
CSA PAGE 22:
- NO STUFF 3G CONNECTOR CIRCUITRY
CSA PAGE 62,66,67,68:
CSA PAGE 67:
CSA PAGE 25:
3/8/2007
CSA PAGE 25:
CSA PAGE 62,66,67,68:
- SYNC FROM AUDIO TEAM.
CSA PAGE 94:
MICROPHONE THROUGH LVDS CABLE
CSA PAGE 34:
- 5029811 CHANGE Q7940 FROM 376S0326 TO 376S0558.
- 4999533 SWAP PIN 2 AND PIN 3 OF MIC CONNECTOR, BACK TO M42 PIN OUT.
Revision History
- WAKE-ON-WIRELESS SUPPORT - RADAR: 4954357
CSA PAGE 4:
CSA PAGE 8:
- ADD CRITICAL TO U2900.
CSA PAGE 44:
- ADD CRITICAL TO U4401.
CSA PAGE 46:
CSA PAGE 49:
CSA PAGE 52:
- STUFFED R6740.
CSA PAGE 68:
- NO STUFFED R6854
CSA PAGE 72:
CSA PAGE 50:
- SMC MANAGEMENT SMBUS CONNECTION:
7/10/2007
- BOOTROM PART NUMBER CHANGES FROM 341S2085 TO 341S2196.
- SMB_ME_CLK AND SMB_ME_DATA ON SOUTHBRIDGE DISCONNECTED FROM SMB_MGMT_CLK AND SMB_MGMT_DATA FROM SMC.B
- THE 10K PULL-UP RESISTORS (R5230 AND R5231), AND STILL REMAIN CONNECTED TO PP3V3_S5_SMBUS_SB_ME AND STAY ON THE SB SIDE.
- ADD TWO NEW 10K PULL-UP RESISTOR (R5232 & R5233) TO =PP3V3_S3_SMBUS_SMC_MGMT.B
CSA PAGE 59:
- ICH8-M ME SMBUS:
- CHANGE R5077 FROM PULL-UP TO A PULL-DOWN RESISTOR AND NAME IT SMC_SMS_INT.
- REMOVE ALIAS FOR =SMC_SMS_INT TO SMC_PG1 - SIGNAL SHOULD JUST BE CALLED SMC_SMS_INT.
- ADD R4670 & R4671. (USB BYPASS ROUTING).
- CHANGE U4675 FROM APN 353S1505 TO APN 353S1742. (SMALL PACKAGE)
CSA PAGE 59:
CSA PAGE 46:
CSA PAGE 67:
CSA PAGE 39:
CSA PAGE 50:
CSA PAGE 62:
CSA PAGE 67:
7/11/2007
- CHANGE R7208 FROM 8.66K TO 15.8K.
- MADE DZ6702, DZ6703, DZ6704, DZ6705, DZ6752, DZ6753, DZ6754, DZ6755, DZ6770, DZ6771B CRITICAL.
- REMOVED NO STUFF RESISTORS R6730, R6731, AND R6732. ALSO REMOVED L6774.
- MADE NO_TEST ATTRIBUTE VISIBLE FOR NET NC_VRP CONNECTED TO PIN 37 OF U6200.
- CHANGED C6210 FROM A CASE-R 10UF TANT. CAP. TO A SMA-LF 3.3UF TANT. CAP.
-ADD 2ND SMS (U5930).
- THE PULL-UP RESISTORS SHOULD BE CONNECTED BETWEEN SMB_MGMT_CLK AND SMB_MGMT_DATA TO =I2C_SMS_SCL AND =I2C_SMS_SDA OF THE NEW ACCELEROMETER.
- STUFF U5930 (DIGITAL ACCELEROMETER) CIRCUIT.
- STUFF C3210 AND C3211.
- REMOVE R5077 (BECOMES R5931).
- ADD R5931 (WAS R5077 BEFORE), 10K PD ON SMC_SMS_INIT.
- ADD R5930, 10K PU ON SMC_SMS_INT.
- UPDATE PN FOR FANCY RJ45 CONNECTOR, 514-0475.
- CHANGE Z0901 AND Z0906 FROM 998-1178 TO 998-1186 (NON-PLATED).
- 4954357 ADD =PP3V3_S3_AIRPORT_AUX BACK TO PP3V3_S3 ALIAS.
- UPDATE BOM OPTION TABLE FOR J6700.
7/17/2007
CSA PAGE 59:
CSA PAGE 43:
7/12/2007
- UPDATE SYMBOL FOR U5930, VENDOR PART NUMBER CHANGES FROM SMB380 TO BMA150.
CSA PAGE 38:
CSA PAGE 4:
7/13/2007
- UPDATE BOM OPTION TABLE FOR J9401.
CSA PAGE 94:
CSA PAGE 79:
- CHANGE C3831 AND C3832 FROM 138S0582 TO 138S0554 (DON’T NEED LOW-PROFILE PARTS).
7/24/2007
CSA PAGE 4:
- CHANGE BETTER AND BEST CPU TO G0 STEPPING PARTS (FROM 337S3464 TO 337S3500).
CSA PAGE 22:
- STUFF R2242 AND NOSTUFF R2247.
CSA PAGE 92:
- CHANGE R9211 AND R9212 FROM 16.5K TO 9.09K.
CSA PAGE 62:
- CHANGE J4300 FROM 514-0289 TO 514-0456 (SAME JEDEC).
- UPDATE BOM OPTION TABLE FOR J4600 AND J4601.
- ADD PAGE_TITLE AUDIO: CODEC.
- NORMAL CHANGES FROM 514-0288 TO 514-0457, FANCY CHANGES FROM 514-0315 TO 514-0477.
- CHANGE J4600 AND J4601 FROM 514-0288 TO 514-0457 (DIFFERENT JEDEC, SAME LANDPATTERN).
- NORMAL CHANGES FROM 514-0359 TO 514-0456, FANCY CHANGES FROM 514-0316 TO 514-0476.
- UPDATE BOM OPTION TABLE FOR J4300.
051-7455
Revision History
5 76
01
SYNC_MASTER=N/A
SYNC_DATE=N/A