EWT810
INSTRUCTIONS BOOK
WASHING
MACHINES
EWT 1010
EWT 810
1. TECHNICAL CHARACTERISTICS
DIMENSIONS Height
Width
Depth
VOLTAGE / FREQUENCY
TOTAL POWER
WATER PRESSURE
Connection to the water network
Spin speed EWT 1010
This washing machine complies with CEE directive 89-336 about the limitation of radioelectric disturbances and
directive CEE 73-23 for electrical safety.
Minimum
Maximum
EWT 810
850 mm
400 mm
600 mm
230 V / 50 Hz
2300 W
0,05 MPa (0,5 bar)
0,8 MPa (8 bars)
Type 20x27
1000 rpm
850 rpm
2. WARNINGS
Keep this user’s manual with your washing machine. If you sell your washing machine or give it away, make sure that it is accompanied by its user’s manual. The new user can then be informed of how the washing machine operates and read relevant warnings.
These warnings have been written for your safety and for the safety of others. Please read these comments carefully before installing and using your washing machine. Thank you for your attention.
• When you receive your washing machine, unpack it or have it
unpacked immediately. Check its general appearance. Make
any reserves in writing on the delivery form and keep a copy.
• Your washing machine was designed for use by adults. Make
sure that children do not touch it or use it as a toy.
• Do not modify or attempt to modify the characteristics of this
washing machine. This could be dangerous for you.
• Your washing machine is intended for normal domestic use. Do
not use it for commercial or industrial purposes or for any
purpose other than that for which it was designed : to wash, to
rinse and to spin.
• Unplug the power suplly plug and close the water supply tap
every time after using your washing machine.
• Only wash articles that can resist machine washing. Refer to
the instructions on the label for each article.
• Do not wash underwear with bones, or any material without
hems, or torn materials in your washing machine.
• Remember to remove all coins, safety pins, boraches, screws,
etc., before each wash. They can cause serious damage if they
are left in your washing.
• Do not put articles in your washing machine if you have used a
solvent, alcohol, trichloroethylene, etc., to remove stains from
them. If you must use these stain removers, wait until the product has evaporated before putting the articles in the drum.
• Collect all small articles such as socks, belts, etc., in a small
cloth bag or pillow case.
• Use the quantity of detergent indicated in the «proportioning of
detergents» section.
• Always unplug the washing machine before cleaning it and
doing any maintenance.
• This washing machine is heavy. Take care when moving it.
• You must remove the packing on the washing machine before
use. Failure to remove all transport protection devices can
cause damage to the washing machine or nearby furniture.
The washing machine must be unplugged while packing is
being removed.
• Do not allow any one other than a qualified plumber to make
the hydraulic connections necessary to install your washing
machine.
• The washing machine must be plugged in to a power outlet with
a conform earth.
• Call a qualified electrician if the electrical installation in your
residence is such that you have to modify it before you can connect your washing machine.
• Please read the instructions in the "electrical connections"
chapter carefully before connecting your washing machine.
• After installing your washing machine, make sure that it is not
standing on its electrical power supply cable.
• When your machine is installed on a carpeted floor, make sure
that the carpet does not close off the ventilation openings near
the bottom of the machine.
• The power supply cable may be only replaced by the After
Sales Service.
• Your manufacturer cannot be held responsible for any damage
resulting from a nonconform installation.
• The symbol on the product or on its packaging indicates
that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for
the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local
city office, your household waste disposal service or the shop
where you purchased the product.
146 5431 01 - 04/05
1
3. INSTALLATION
3.1. Unpacking
Packing used to protect internal parts of the washing
machine during transport must be removed before the
washing machine is put into service for the first time.
Remove all packing from the
washing machine. Tilt the washing
machine sideways and then remove
the packing under the motor, and
straighten the washing machine.
Tilt the washing machine backwards, rotate it by a quarter of a turn
on one of its corner to remove the
transport base.
Open the washing machine lid and
remove the immobilization packing
and plastic films.
Close the lid.
3.3. Moving your washing machine
If you want to move your washing
machine, lift it onto its rollers by pulling the lever at the bottom of the
washing machine all the way to the
left. When you have put your
washing machine into the required
location, put the lever back into its
initial position.
3.4. Leveling
Precise leveling will prevent vibrations, noise and movements of the washing machine during operation.
Make the washing machine level by
adjusting the leveling screw that is
too short. Unscrew the stand and
locking collar assembly (lift the
washing machine if necessary).
When the washing machine is stable, maintain the stand on the
ground and turn the locking collar as
far as posible.
3.5. Water inlet
Please install the water inlet hose onto the back of your
washing machine:
- Insert the seal in the hole at the bottom of the back panel (fig. 1).
Use a 10 mm spanner to remove the
two screws and spacers at the back.
You can now see the openings that
must be closed with the caches in the
pack attached to the washing machine; do not forget to fold down the
central capsule.
Make sure that you have removed all
these parts from your washing machine and keep them so that you can
use them again if you need them for
future transport.
If you want to keep your washing machine aligned with the adjacent furniture, you can cut the pipe support
strip at the back of your washing machine. Leave the two side closers in
place.
3.2. Position
Put the washing machine on a flat hard floor in a well ventilated room.
Make sure that your washing machine does not touch the
wall or any other furniture in the room.
- Screw on the bottom fitting of the
water inlet hose as shown in fig. 2
and fig. 3.
- Connect the feed hose connector
onto the water inlet tap, taking care to
position the gasket correctly.
- Turn on the water inlet tap.
The water inlet hose cannot be extended. If it is too short, please contact
the After Sales Department.
3.6. Drainage
- Assemble the hose holder onto the
drain hose.
- Place the assembly in a drainage
pipe (or in a sink) at a height between
70 and 100 cm. Make sure that it will
not fall out.
You must provide an air intake at the
end of the drainage hose, to avoid
any water being siphoned.
Important: the drainage hose must not be extended, on any
account. If it is too short, contact a qualified engineer.
3.7. Electrical connection
You can only connect this washing machine to 230 V single
phase power supply.
Check rating of the fuse line: 10 A at 230V.
The washing machine must not be connected through an
extension cable or a power bar.
Check that the earthing connection is conform with the regulations in force.
2
4. USING
4.1. The control panel
1 - On/Off pushbutton 4 - Spinning speed variator
2 - Half load pushbutton 5 - Program selector
3 - Rinse plus pushbutton 6 - Temperature selector
1
2
3
4
4.2. How to do a wash ?
Before the first wash in your washing machine, we recommend that you should do a preliminary wash at 90°C with detergent but without any washing to clean the tub.
4.2.1. Loading the washing
• Lift the machine cover.
• Open the drum by pressing on the locking button A; the two
flaps automatically separate.
• Insert the washing, close the drum and the cover of your
washing machine.
Warning : before you close the
cover of your washing machine,
make sure that the drum door is
properly closed:
•the two flaps latched together,
A
•the locking button A extended.
5
6
4.2.4. Choice of the temperature
Choose the wash temperature applicable for the selected
programme (using the information given in the programmes
table) and comply with the temperature shown on the care
label for each article to be washed (see the washing guide).
4.2.5. Choice of the pushbuttons
Press the chosen pushbuttons.
4.2.5.1. «Half load» pushbutton
This pushbutton allows to wash small quantity of linen not
much soiled (max. 2,5 kg) on cotton programmes only by reducing the water quantity during rinsings.
4.2.5.2. «Rinse plus» pushbutton
This option adds more water in rinses on Cotton programs.
It is advised for allergic people to detergent products and in
areas with fresh water.
4.2.2. Proportioning of detergents
Your washing machine was designed to reduce water and
detergent consumption, therefore reduce the doses recommended by detergent manufacturers.
Put the powder detergent dose into the wash compartment
and into the prewash compartment if you chose the
«prewash» option. Put the softener into the compartment
if you wish.
If you are using a different type of detergent, refer to the «detergents and additives» section in the washing guide.
4.2.3. Choice of the spinning speed
Choose the spinning speed which corresponds to the nature
of your laundry and to the degree of humidity wished at the
end of the wash.
The knob indicates the possible spinnings on the coton programmes. These spinnings are reduced for the synthetics,
wool and delicate cycles.
4.2.6. Choice of the programme
Select the programme depending on the nature and the degree of soil of the laundry. Turn the programme selector
clockwise to select the chosen programme.
4.2.7. Starting the programme
After you choose the washing programme, press the «On/
Off» pushbutton to start the cycle.
3
Loading...