3COM 1600, 800, IPS 400 User Manual

FFICECONNECT
O
FFICECONNECT
O
SER GUIDE
U
SER GUIDE
U
400, 800, 1600
400, 800, 1600
®
®
WITCH
S
WITCH
S
Part No. DUA1673-4AAA01
Published February 1999
I
NTRODUCTION
Welcome to the world of networking with 3Com®. In the modern business environment, communication and sharing information is crucial. Computer networks have proved to be one of the fastest modes of communication but until recently only large businesses could afford the networking advantage. The OfficeConnect changed this, bringing networks to the small office.
As the power of workstations and business applications increases, heavier demands are made on the available network bandwidth that, if unchecked, can lead to performance problems in a hub-based setup. Installing the OfficeConnect Switch 400 (3C16733), Switch 800 (3C16734) or Switch 1600 (3C16735) allows your network to be segmented so that traffic can be contained effectively, reducing the overall load without affecting access to critical resources.
When referring to the OfficeConnect Switch 400, Switch 800 or Switch 1600, this guide uses the term ‘Switch’.
The Switch is ideal for use with other OfficeConnect products. It is compact and attractively designed for desktop use. The Switch is part of the OfficeConnect range which neatly stacks together with clips, providing a range of facilities.
®
product range from 3Com has
Small Network with OfficeConnect Switch (Circle Shows Units Clipped Together)
For information on these products, see the “OfficeConnect Product Range” sheet that accompanies this product.
The Switch has 4, 8 or 16 10/100BASE-TX ports. This allows you to set up a network with both 10BASE-T and 100BASE-TX hubs and workstations.
C
REATING
Y
OUR
N
ETWORK
Networking Terminology
(instead of all ports like a repeater hub). This operation is called ‘switching’.
A
Network
is a collection of workstations (for example, IBM-compatible PCs) and other equipment (for example, printers), connected for the purpose of exchanging information or sharing resources. Networks vary in size; some are within a single room, others span continents.
A
Local Area Network (LAN)
office, that spans no more than a single site.
Ethernet
is a type of LAN, referring to the technology used to pass information around the network. It operates at 10Mbps (megabits per second).
Fast Ethernet
is a type of LAN that runs up to 10 times faster than standard Ethernet. It operates at 100Mbps.
10BASE-T
100BASE-TX
A
Network Loop
is the name given to the Ethernet protocol that
runs over
Twisted Pair (TP)
is the name given to the Fast Ethernet protocol
that runs over
Twisted Pair (TP)
occurs when two pieces of network
equipment are connected by more than one path.
A
Segment
Packets
is the length of cable connected to a port.
are the units of information your workstations and other equipment send to each other over the network. A can be
Frame
Unicast
(sent to a single device), (sent to multiple devices), or devices).
Bandwidth
refers to the amount of network traffic the network can hold at any one time (information capacity) measured in Workstations or applications that use the network heavily are referred to as using high bandwidth (these are usually users who do a lot of graphical or multi-media work across the network). Fast Ethernet has a higher bandwidth than Ethernet, so it can cope with larger amounts of traffic, which results in faster operation.
Full duplex
operation allows information to be transmitted and received simultaneously and, in effect, doubles the potential throughput of a link.
is a network, usually in an
cable.
cable.
is the data part of the packet and
Multicast
Broadcast
(sent to all
bits per second (bps)
.
The Switch effectively divides up your network, localizing the network traffic and passing on traffic as necessary (as shown in the diagram). If you have workstations that communicate frequently in the same part of the network, traffic between them is not passed to the remainder of the network, reducing the load. If you have any high performance workstations that require a lot of bandwidth, connect them directly to the Switch.
The Switch Separates Your Network and Con trols the Information Effectively
Connecting 10BASE-T and 100BASE-TX Networks
The 10/100 ports can each be connected to either a 10BASE-T or 100BASE-TX network. If you have both types of network, you can connect them using the Switch so that all your workstations can communicate. Alternatively, if you use 10BASE-T and want to improve performance by introducing 100BASE-TX, the Switch protects your investments because it maintains 10BASE-T connections to your original network equipment.
How the Switch Can Be Used
Switching
When a network of repeater hubs is in operation, any information that is sent by the workstations is passed around the whole network (regardless of the destination of the information). This can result in a lot of unnecessary traffic that can slow the network down. The Switch solves this problem because it ‘listens’ to the network and automatically learns what workstations can be reached through its ports. It can then selectively pass on any information by transmitting the traffic from the relevant port only
Before You Start
Your OfficeConnect Switch comes with:
One power adapter for use with the Switch. The Switch 400 and Switch 1600 have an additional power cord for use with the power adapter.
A Product Registration card for you to fill out and return
Four rubber feet
Four stacking clips
An OfficeConnect Product Range sheet
This guide
Loading...
+ 5 hidden pages