Alcatel-Lucent 1511 BA User Manual

Size:
951.63 Kb
Download

Alcatel-Lucent1511 BA

Business Access Multiplexer | 2 Mb/s 30-ChannelPrimary Rate Multiplexer

The Alcatel-Lucent1511 BA is a 2 Mb/s30-channelmultiservice access multiplexer, which can be used across a wide range of companies for business access and utility network applications. It also provides grooming functionalities for GSM and wireless local loop networks. For example, railway networks, pipelines for oil, gas and water and power utilities use utility network applications with different sets of service requirements. Whereas railway and pipeline installations require a linear or ring type of network withdrop-and-insertfunctions, other installations require a mesh type of network. For all of these applications theAlcatel-Lucent1511 BA offers the ideal solution.

Features

Channel bank for 30 x 64 kb/s channels

2 Mb/s G.703/G.704 aggregates

Variety of tributary boards for voice, data and Ethernet

Local or remote craft terminal and centralized element management platform

Drop-and-insertfacility at 64 kb/s granularity

Voice and data conference circuits

Built-inringing generator and 12 or 16 kHz metering pulses for coin boxes and private meters

Support for incorporation of PDH terminal units for transport of E1 streams over optical fiber and copper cable (G.shdsl)

Automatic trail protection of N x

64 kb/s payload

48 V DC power supply or 110 V AC or 220 V AC with optional battery backup

Redundant DC/DC or AC/DC conversion

Benefits

Protection of business-criticalservices with high reliability, APS and trail protection

Ease of upgrading with a modular architecture for rapidly growing or changing networks

Full software control of network configuration, maintenance and supervision

Network Element Management

Fast, efficient and flexible management is the key to success for any network. Alcatel-Lucent’snetwork management software, based onITU-TM.3010, satisfies all three of these criteria in aneasy-to-learnandeasy-to-usepackage. Network management of all elements in a system is performed from a single terminal comprising a compatible PC running Windows or a workstation loaded withAlcatel-Lucentnetwork management software.

Architecture

The PCM Controller (PCMC2) interfaces the users and the E1 aggregate side.

The controller connects the analog, data or N x 64 kb/s data terminal channels of the tributary boards, or the PCMC2 in slave mode, to the 2,048 kb/s G.703/G.704 aggregate via an internal serial bus.

The PCMC2 provides:

A transmission/switching interface and HDB3 to binary coding/decoding, retiming, frame alignment and supervision, cyclic redundancy check

#4 (CRC4) generation/monitoring, channel mapping, CAS, alarm treatment and test facilities

An asynchronous serial communication channel to a central alarm supervising unit through which the user can communicate about equipment configuration, status and alarms

Two serial channels for embedded operation channel (EOC). These channels can be used for transport of network management protocols between the network element and its centralized management units.

Power unit boards for DC/DC and AC/ DC conversion are provided for each subrack assembly and can be duplicated for redundancy.

Applications

POTS Subscriber Multiplexer

The POTS subscriber multiplexer is used in the subscriber network and allows a flexible mix of voice and data interfaces. Adaptation of the signaling to the customer’s requirements can be done easily.

ISDN-BRI

The Alcatel-Lucent1511 BA can be used forISDN-BRIapplications. Both 2- and4-wire(U with line code 2B1Q and S0/I.430) interfaces are available. Each interface uses three timeslots

(2B + D16/M) on the 2 Mb/s G.703 link.

Hot Line

Hot Line is a bi-directionalapplication, with a centralized battery set, where one subscriber hooks off and the other is called without dialing. It uses the same board as the POTS application. This board’s lines can be programmed either as a POTS or Hot Line.

Ringdown

Manual Ringdown (MRD) is an Alcatel-

Lucent 1511 BA application that permits the connection of two local battery (LB) telephone sets or the connection of a local battery telephone set to a central switch board. This application is widely used by stock market brokers. It requires the use of a special ringdown board.

Direct Dialing In

The Alcatel-Lucent1511 BA provides direct dialing in (DDI), a feature whereby the dialing information is sent directly from the PSTN to the PABX, which then sets up the connection to the PABX subscriber.

Data Multiplexer

The Alcatel-Lucent1511 BA can be used as a data multiplexer. The possible data tributaries are:

64 kb/s G.703 co-directional— with optional E&M signaling

64 kb/s G.703 contra-directional

2 Mb/s and N x 64 kb/s G.703/G.704.

(fractional E1)

Low speed: 75 b/s to 64 kb/s for V.36, V.35, V.28 and X.21

N x 64 kb/s (N = 1 to 31); interfaces: V.35, V.36 and X.21

Remote Data Unit

The Alcatel-Lucent1511 BA provides an integrated digital interface to remote data units (RDUs). The RDUs are provided with one or two of the following interfaces in any combination: V.35, V.36, X.21 and V.24/V.28 up to 128 kb/s, analog and 64 kb/s G.703co-directionalinterfaces. Performance monitoring on the

RDU is foreseen on the digital link.

High Quality Audio Tributaries

The Alcatel-Lucent1511 BA can perform unidirectional audio transmission.

This audio board uses MPEG-215 kHz sampling.

2/4-WireAudio Interface

Connection between analog modems or PABX ports for tie-lineconnections can be achieved with the2/4-wireaudio board. Variants with or without E&M wires are available.

Conference Bridge

Two types of conferences are possible:

Master-slaveconference: One participant is considered the “master” and all others are considered “slaves.”

One master with up to 29 slaves is possible.

Full conference: This type of conference is used when all participants need to share information equally. Every participant receives information from all other participants but himself or herself.

These two types of conferences can be used for voice, data or signaling.

The conference bridge is a simple and useful board in networks with super­ visory control and data acquisition

(SCADA) and/or audio dispatching requirements.

Dry Relay Contacts

This board has a number of detectors for dry relay contacts. It is used for collecting alarm indications of collocated equipment and enables the visualization of alarm states on the same craft terminal or server as that being used for the multiplexer functions.

Integrated Optical Transport

Boards for optical PDH transport of

4 or 16 E1 streams can be plugged into the Alcatel-Lucent1511 BA subrack and managed by the same management tools. See theAlcatel-Lucent1521 FL and theAlcatel-Lucent1531 FL.

2 Alcatel-Lucent1511 BA | 2 Mb/s30-ChannelPrimary Rate Multiplexer | Data Sheet

Figure 1. Alcatel-Lucent1511 BA User Interfaces

10/100 Mb/s

U (2Wire)

LAN

Ethernet

Remote 2x64 kb/s; 128 kb/s andA-LLVAM

 

Uko (2Wire)

ISDN-BRA

 

 

 

S0 (4Wire)

ISDN-BRA

 

 

 

ab (2Wire)

PSTN/Hotline/Payphone

 

 

 

FE1 (G.703)

PABX

 

 

1511 BA

ab (2Wire)

Magneto Set

 

 

V.35/V.36/V.28/X.21

64 kb/s-LLand V.110 Subrate

 

64 kb/s-G.703

Coand Contra 64 kb/s

 

V.35/V.36/X.21

Nx64kb/s-LL

 

2Wire

Hifi-Audio

 

4/2Wire

Analog-LLModem

 

Figure 2. Alcatel-Lucent1511 Typical Applications

Main Office

 

 

Satellite Offices

ab HotLine

 

 

ab HotLine

 

1515 CXC

 

ab PABX Line

ab PABX Line

 

 

 

 

 

Tie Line

 

 

Tie Line

 

 

 

PABX

 

 

PABX

2 Mb/s

 

Mb/s

 

 

Server

 

Transport

LAN

LAN

 

 

G.703

64 kb/s

703

 

 

1511 BA

 

1511 BA

SCADA

SCADA PLC

Controls

Host

 

 

 

 

 

Alarms and Data

CCTV Monitor

CCTV Camera

and Control

 

 

Alcatel-Lucent1511 BA | 2 Mb/s30-ChannelPrimary Rate Multiplexer | Data Sheet

3

Automatic Protection Switch

The automatic protection switch (APS) enables route protection on E1 level. If used, the Alcatel-Lucent1511 BA transmits data via two different E1 routes. At the receive side, data coming from the preferred route is used; if this route fails, data is taken from the other side.

Ethernet Switching

On an E1 trail across multiple AlcatelLucent 1511 BA multiplexers, a group of 64-kbtimeslots (N: 1...31) is reserved to carry Ethernet frames. In each AlcatelLucent 1511 BA, one10/100Base-TLAN board (LANtrib) can drop/insert its local Ethernet traffic onto these reserved timeslots. To connect multiple Ethernetbased end devices, the LANtrib offers five externalRJ-45interfaces. The LANtrib also switches LANs across multiple and distinctAlcatel-Lucent1511 BA multiplexers. Switching between the local five Ethernet ports runs at wire speed.

Technical Specifications

Main Characteristics

Compliant with all relevant ITU-Trecommendations including: G.703, G.704, G.706, G.711, G.712, G.732, G.784, G.823, G.826, V.28, V.35, V.36, and X.21

Clock Synchronization

Internal clock (50 ppm)

Extracted from E1 port

External via 2,048 MHz clock (ITU-TG.703 § 10) or 64 kHz (G.703 § 1.2.2)

Clock and backup priority rules are selectable via configuration management.

Mechanical Design

Uses same technology as the other products in the Alcatel-Lucentaccess product family

Plug-inprinted boards with Double Euro format.State-of-the-artcomponents ensure low power consumption and high reliability.

Subracks (can be mounted in rack or cabinet):

¬T9 subrack: Width of 120 mm

(4.72 in.), 240 mm (9.45 in.),

360 mm (14.17 in.) or 480 mm

(18.89 in.)

¬19-in.subrack:

-height: 7U (1U = 44.45 mm, 1.75 in.)

-Can be mounted in a 300-mmdeep (11.81 in.) ETSI rack

ETSI T9 and 19-in.racks:

¬available in two heights: 2,200 mm (86.61 in.) (with six Alcatel-Lucent1511 BA subrack mounting levels) and 1,800 mm (70.87 in.) (with five mounting levels)

Cabinets: Both indoor and outdoor variants available

Power Supply

-38.5V to-72V DC

110/220 V AC ± 20%

Environment

>Operating temperature: -5C to +50 C (23 F to 122 F)

>Transport and storage temperature: -40C to +70 C(-40F to +158 F)

Compliant with:

¬ETS 300 019-2-1

¬ETS 300 019-2-2

¬ETS 300 019-2-3

EMC

EMC on rack basis (EMC directive 89/336/EEG [EN 50081-1,EN50082-1])

EMC on subrack basis (ETS 300-386-1)

www.alcatel-lucent.com

Alcatel, Lucent, Alcatel-Lucentand theAlcatel-Lucentlogo are trademarks ofAlcatel-Lucent.All other trademarks are the property of their respective owners. The information presented is subject to change without notice.Alcatel-Lucentassumes no responsibility for inaccuracies contained herein.

© 2008 Alcatel-Lucent.All rights reserved. CAR9718080111 (02)