English
Cautionary Notes
1
GS1200
1) Please read this manual thoroughly prior to installation.
2) Before installing, check the components and condition of the
product, and if any problem is found, contact the retailer.
3) Avoid inserting objects or hands into the system while it is in
operation to prevent product damage and injuries.
4) Check the manual when connecting cables. Incorrect connections
may cause short circuits leading to re hazards.
5) Do not block the Front Intake Vent or the Rear Exhaust Vent.
6) Keep this unit away from heat sources, direct sunlight, water,
oil, and humid environments, and place the unit on a flat, stable,
vibration-free, and well-ventilated area.
7) Do not clean the product surface with chemicals or wet cloth.
(chemicals: industrial brightener, wax, benzene, alcohol, paint
thinner, mosquito repellent, aromatics, lubricant, detergent etc.)
8) Please wear gloves while handling this product to prevent injuries.
9) Product design and specications may be revised to improve quality
and performance.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due to
external causes, including but not limited to, improper use, problems
with electrical power, accident, neglect, alteration, repair, improper
installation, or improper testing.
Eng
1
GS1200
Product Details
2
(1) Specications
Models GS1200
Type Full Tower
Dimensions (W×H×D) 260 × 570 × 640㎜ (10.2” × 22.4” × 25.1”)
Weight 12.4㎏ (27.3 lb)
Materials Aluminum, Plastic, Steel
Color Black
Motherboards Compatibility Standard ATX / m-ATX / E-ATX
Power Supply Compatibility Standard ATX / ATX12V
PCI/AGP Card Compatibility Full Size, 350 mm (13.7")
5.25" External Bay x 4
Drive Bays
Expansion Card Slots 7 Solots
I/O Ports
Cooling
Components
3.5" External Bay x 1, Internal Bay x 6
5.25"/3.5"/2.5"
Hot-swap 3.5" Support Hot-swap x 4 (HDD Docking x 1)
Headphones x 1, Mic x 1, USB 2.0 x 3 , e-SATA x 1 , USB 3.0 x 1
Front 92mm Fan Vent x 2(2 Fans included)
Top 200mm Fan Vent x 1 (1 Fan included)
Rear 120mm Fan Vent x 1 (1 Fan included)
Side 200mm Fan Vent x 1 (1 Fan included)
Bottom 120mm Fan Vent x 2 (Fans optional )
1 (3in-1)
(2) Product Information
Front Top Side (left)
2
(3) Top Panel I/O Ports and HDD Docking Station
HDD Docking Station
USB 2.0
USB 3.0
e-SATA
GS1200
Eng
Power LED
Reset Button
USB
USB USBe-SATA USB
HEADPHONE
RESET
MIC
Mic
Headphones
POWER
HDD LED
Power Button
3
GS1200
(4) Exploded View
⑩
⑪
⑫
⑬
⑨
⑧
⑦
⑥
⑤
④
# Part Name Units
① HDD Tray 6
② HDD Tray Cover 2
③ Front Cover 1
④ Stand (front) 1
⑤ Stand (rear) 1
⑥ PSU Support 1
③
②
①
# Part Name Units
⑧ Side Cover (right) 1
⑨ Side Cover (left) 1
⑩ Top Cover 1
⑪ Chassis 1
⑫ 5.25” Bay Cover 3
⑬ Adapter Tray 1
⑦ PSU Bracket 1
4
(5) Parts
GS1200
Eng
Main Unit
Stand (front ×1, rear ×1)
Stand-O × 11 A Bolt(#6-32*12mm) × 12
B Bolt(#6-32*6mm) × 24
[M/B, PSU]
User’s Manual × 1
CPU 12V Extension Cable × 1
[HDD]
C Bolt(M3*12mm) × 4
[Stand]
D Bolt(M3*6mm) × 4
[SSD]
Cable Tie × 10
5
GS1200
Installation
3
(1) Stand Assembly
C Bolt
(2) Side Cover Removal
6
(3) PSU Installation
Type A Type B
GS1200
Eng
Or
Type A Type B
B Bolt
Tip
▶ Type A (PSU independent cooling)
If the PSU’s fan points downwards, the PSU’s cooling performance is
enhanced.
▶ Type B (Case Air Circulation Type)
If the PSU’s fan points inwards, the PSU’s cooling performance is
enhanced.
※ When using the case in a dusty environment, use Type B.
7
GS1200
(4) Motherboard Installation
Please refer to the diagrams below for additional Stand O positions (based
on motherboard type).
ATX Board
m - ATX Board
Stand-O
B Bolt
8
(5) VGA Card Installation
(6) Hot Swap HDD Installation
1) HDD Tray Removal
GS1200
Eng
1
2
1
9
GS1200
2) HDD Installation (to HDD Tray)
① ‘Open’ the Hot Swap Tray by pressing the Hot Swap Tray’s Hooks located on
the underside, and pushing in the direction as shown in the diagram.
② Install the HDD and check that the Hot Swap Tray’s Fixing Pins and the HDD’s
holes are properly aligned and fastened.
3.5”HDD
③ Fully insert the HDD installed Hot Swap Tray into the Hot Swap Bay.
3.5”HDD
3.5”HDD
3.5”HDD
10
(7) 5.25” / 3.5” Drive Installation
1) 5.25” ODD Installation
GS1200
Eng
11
GS1200
2) Adapter Tray Installation
① Adapter Tray Removal
② Drive Installation to Adapter Tray
A. 3.5” FDD Installation
D Bolt
3.5” FDD
12
B. 3.5” HDD Installation
3.5” HDD
3.5” FDD
B Bolt
3.5” HDD
C. 2.5” SSD Installation
SSD
3) Top HDD Docking Station
① 3.5” HDD Installation
GS1200
D나사
Eng
SSD
② 2.5” HDD Installation
13
GS1200
4) Hot Swap PCB
① Rear
ZM-HS100 HOT SWAP PCB
A
B
C
HIGH
LOW
S-ATA Connector
4-Pin Power Connector
3-Pin Fan Connector
Fan Controller
② Front
ZM-HS100 HOT SWAP PCB
a
b
c
Caution
▶ The S-ATA connectors connect in A=a / B=b / C=c conguration.
▶ To use the Hot-Swap feature, the S-ATA Cable(s) and the 4-Pin power cable must
be connected to the Hot-Swap PCB.
▶ For HDD stability, please power the system OFF before removing the HDD.
▶ Frequent installation and removal of an HDD can wear connectors.
Tip
▶ The fan controller enables selection of 12V or 5V power source.
▶ 1 Hot Swap PCB comes standard at the bottom of the case. Additional Hot Swap
PCB’s (ZM HS100) can be purchased separately.
14
(8) Cable Connection
1) Power Button and LED Cable
or
GS1200
Power Button Side
Eng
Power LED
Power
Motherboard side
Reset
HDD LED
2) Top Panel I/O Port Cable
Top Panel I/O Port side
Audio
HD Audio
AC ’97
USB 2.0 USB 3.0
Motherboard side
e-SATA
Tip
▶ To connect USB 2.0, 3.0, 3-SATA and audio cables, please refer to the motherboard
manual.
▶ When the +/- polarities are reversed, the LED’s will not function.
15
GS1200
Optional Fan Installation and Replacement
4
(1) Side Cover Fan (200㎜ - standard / 120㎜ - optional)
16
200㎜ Fan Pre-installed
(standard)
(2) Bottom Panel Optional Fan (120㎜)
2 x 120㎜ Fan Installation
(optional)
GS1200
(3) HDD Cover Tray Fan Removal
Open the HDD Cover and remove the Fan Bracket before uninstalling the
Bracket from the Fan.
Caution
▶ The replaceable fan’s specications are 92㎜(W) x 92㎜(L) 25㎜(H).
▶ It is recommended to install the fan so that it sucks air into the case.
Eng
17
Loading...