4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
Introduction
This manual provides technical information necessary for servicing the VXR-7000 FM Land Mobile Repeater.
Servicing this equipment requires expertise in handling surface-mount chip components. Attempts by non-qualified
persons to service this equipment may result in permanent damage not covered by the warranty, and may be illegal in
some countries.
Two PCB layout diagrams are provided for each double-sided circuit board in the repeater. Each side of is referred to
by the type of the majority of components installed on that side (“leaded” or “chip-only”). In most cases one side has only
chip components, and the other has either a mixture of both chip and leaded components (trimmers, coils, electrolytic
capacitors, ICs, etc.), or leaded components only.
While we believe the technical information in this manual to be correct, VERTEX STANDARD assumes no liability
for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing
out any inconsistencies in the technical information would be appreciated.
PA Unit .................................................................... 27
TX Unit ..................................................................... 35
RX Unit ....................................................................43
CNTL Unit ............................................................... 55
LPF Unit ................................................................... 73
Display Unit ............................................................75
Key Unit ................................................................... 79
Filter Unit ................................................................ 87
VR Unit .................................................................... 95
SQL Unit .................................................................. 97
PS Unit ..................................................................... 99
1
Page 2
Operating Manual Reprint
Controls & Connectors
Front Panel
POWER Switch
This is the main power switch for the repeater.
LED Indicators
AC: This LED glows green during AC operation.
DC: This LED glows yellow during DC operation.
MIC Jack
This 8-pin modular jack accepts the microphone input, and provides a standby control line to activate the
transmitter when using the “BASE” mode of operation. This jack also provides a “Hook” control line, as
well as a “Clone Data” line.
BASE/REPEATER Switch
This switch toggles the operating mode between the
“REPEATER” mode and the “BASE” transceiver
mode. When the “REPEATER” mode is selected, the
LED above it glows green. While in the “BASE” mode
(the green LED is off), you can speak into the microphone to use it as a transceiver. For normal repeater
operation, set this switch to the “REPEATER” mode.
LOCAL/REMOTE Switch
This switch toggles the control mode between the “RE-
MOTE” mode and “LOCAL” mode. When the “LOCAL” mode is selected, the LED above it is off, and
the repeater operates according to the control data programmed into the repeater. While in the “REMOTE”
mode, the LED glows green, and the repeater operates according to the control instructions received from
an external device (connected to the ACC jack on the
rear panel).
MONITOR Switch
This switch selects the “Squelch” (receiver mute) mode.
When the green LED above it is off, “Tone” or “Coded”
squelch is active. When you press this switch momen-tarily, the green LED will glow steadily; in this condition, only “noise squelch” is active, and any signal present
on the channel will be heard. If you press and hold this
switch for more than 2 second, the green LED will blink
and the squelch will open; in this condition, background
noise will be heard if no signal is present.
ACCESSORY Switch
This switch can be set up for special applications, such
as High/Low power selection, as determined by your
Vertex Standard dealer. The LED above it glows green
when this function is activated. For further details,
contact your Vertex Standard dealer.
VOL Knob
This control knob adjusts the receiver volume level
from the front panel speaker. If desired, this control
knob may be set fully counterclockwise when repeater
monitoring is not needed.
SQL Knob
This control knob selects the noise squelch threshold
level. Set it to a position just above the point where
the BUSY lamp goes out when no signal is present.
Channel Selector Buttons ( and )
Press one of these buttons to select the operating channel.
Channel Indicator
This seven-segment LED indicates the operating channel number.
2
Page 3
ANI Display
The ANI LCD (Liquid Crystal Display) indicates the
pre-programmed ANI message according to the ANI
code received.
TX/BUSY Indicator
The BUSY indicator glows green when the channel is
busy, and the TX indicator glows red when the repeater
is transmitting.
Rear Panel
Operating Manual Reprint
ANI RESET Button
(1) ANI
Press this button to clear the message on the ANI
display, and turn off the LCD backlight.
(2) ENI
Press this button to turn off the Alert tone.
Press this button again to clear the message on the
ANI display, and turn off the LCD backlight.
EXT SP Jack
This 3.5-mm, 2-pin jack provides variable audio output for an external speaker. The audio output impedance at this jack is 4 Ω ~ 16 Ω, and level varies according to the setting of the front panel’s VOL con-
trol.
TX Antenna Jack
This N-type coaxial jack provides the transmitting output signal for connection to the transmitting antenna
or TX jack on the duplexer, if used. The output impedance requirement is 50 Ω.
RX Antenna Jack
This N-type coaxial jack accepts the receiver input
signal from the receiving antenna or RX jack on the
duplexer, if used. The input impedance requirement is
50 Ω.
ACC Jack
This DB-25 connector provides a data interface between the microprocessor in the VXR-7000 and peripheral devices (such as the VX-TRUNK Unit).
LINE Jack
This 8-pin modular jack is used for remote control. It
provides TX and RX audio, TX keying, and squelch
status output. The TX and RX audio impedance is 600
Ω.
GND Terminal
For best performance and safety, the GND terminal
should be connected to a good earth ground using a
short, heavy, braided cable.
AC Jack
This receptacle accepts the AC power cord, which
should be connected to the AC mains supply or wall
outlet. The AC line voltage must match that for which
the repeater is wired.
BATT Terminal
These terminal posts accept 12~ 15 VDC for operating the repeater from a battery or other DC source.
When operating from AC mains, a small trickle current is present at these terminals to maintain battery
charge. A battery rated for 12 volts, 55 Ah (minimum)
is recommended for short-term emergency/backup operation.
3
Page 4
Operating Manual Reprint
ACC Connector Port
The VXR-7000 repeater is provided with a 25-pin DB25F female connector for interconnections to accessories. Use a DB-25M 25-pin male connector to connect
accessories to the repeater. The pins on the accessory connector are explained in detail as follows:
Pin 1: GND
Chassis ground for all logic levels and power supply
return.
Pin 2: +13.8 V [Power Supply]
This pin provides 13.8 Volts, 1.0 A, regulated DC from
the repeater supply. Use a 1 A fuse in the external
device’s DC line to prevent damage to the repeater.
Pin 3: TX AF IN [Analog Transmitter Input]
(Voice Band: 300 ~ 3,000 Hz)
Input impedance is approx. 600 Ω. This audio is injected before the splatter filter stage, so excess signal
input levels are clipped.
Use shielded cable to connect to this pin, and connect
the shield to GND.
Pin 4: TONE IN [Transmitter Input]
(Sub-audible Band: 6 ~ 250 Hz)
The input is high impedance (approx. 22 kΩ). Injecting too high a voltage here causes over-deviation of
CTCSS or DCS, degrading performance. Use shielded
cable to connect to this pin, connecting the shield to
GND.
Pin 5: N.C. (No connection.)
Pin 6: DISC OUT [Analog Output]
(Wide-Band: 0 ~ 3,000 Hz)
Received signals with standard deviation produce
approx. 1 V
is approx. 600 Ω, and is extracted before the de-emphasis and squelch circuitry. Use shielded cable to connect to this pin, and connect the shield to GND.
p-p audio at this pin. The output impedance
Pin 7: GND
Chassis ground for all logic levels and power supply
return.
Pin 8: RSSI [Analog Output]
A DC voltage proportional to the strength of the signal
currently being received (Receiver Signal Strength In-
dicator) is provided on this pin. This low impedance
output is generated by the receiver IF sub-system and
buffered by an internal op-amp. Typical voltages are
graphed as follows:
Pin 9: COAX. SW [Logic Output (Active Low)]
This output is intended for controlling an external coaxial switching relay. It is an open collector output
which can sink approx. 10 mA when active. This signal only switches if the repeater has been programmed
for “SIMPLEX” mode. If programmed for “DU-PLEX,” the signal remains open (high impedance) at
all time.
Pin 10: N.C. (No connection.)
Pin 11: NSQ DET
This is an open-collector, active-low output capable of
sinking about 10 mA. It indicates that the receiver
squelch is open. If the squelch control is properly set,
this indicates a carrier on the receiver channel.
ACC Jack
DB-25 Pin Numbering
4
Page 5
Operating Manual Reprint
Pin 12: EXT PTT
This input is internally pulled up to 5 VDC. When
pulled low by an external device, it keys the repeater
transmitter while the repeater is operating in the
“BASE” mode. Avoid voltage in excess of 5 V on this
pin, or internal damage to the microprocessor on the
repeater CNTL Unit may result.
Pin 13: GND
Chassis ground for all logic levels and power supply
return.
Pin 14: GND
Chassis ground for all logic levels and power supply
return.
Pin 15: N.C. (No connection.)
Pin 16, 17, 18, & 19: REMOTE CH DATA
[Logic Inputs D3, D2, D1, and D0] (Active Low)
These inputs are internally pulled up to 5-V DC. When
pulled low by an external device, they select one of the
16 pre-programmed repeater operating channels. The
logic truth table below shows the combinations for se-
lecting all 16 channels.
In the truth table, “1” represents no connection, and
“0” represents a ground connection on the pin.
The channel selection logic is not inhibited while the
transmitter is keyed: the repeater will change frequency
when instructed, even while transmitting.
Avoid voltage in excess of 5 V on these pins or inter-
nal damage to the microprocessor on the repeater CNTL
Unit may result.
Channel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Pin 16
(D3)
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
Pin 17
(D2)
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
Pin 18
(D1)
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
Pin 19
Pin 20: GND
Chassis ground for all logic levels and power supply
return.
Pin 21: A-OUTPUT [Logic Output] (Active Low)
This open collector logic output is pulled low when
the front panel’s ACCESSORY key is turned on. It
can sink approx. 10 mA when active.
Pin 22: RXD LOW
[Digital Output for DATA Communications]
(300 ~ 3,000 Hz)
This pin is an output for low speed receiving data signals, with the data being extracted after the de-emphasis and low pass filter stages.
Pin 23: RXD HI
[Digital Output for DATA Communications]
This pin is an output for high speed receiving data signals, with the data being extracted immediately after
the discriminator prior to any de-emphasis).
Pin 24: TXD LOW
[Digital Input for DATA Communications]
(300 ~ 3,000 Hz)
This pin is intended to be used as a low speed digital
data signal input to the repeater. This digital data signal is injected before transmitter pre-emphasis and limiting stage, so excess signal input levels are clipped.
Pin 25: TXD HI
[Digital Input for the DATA Communications]
This pin is intended to be used as a high speed digital
data signal input to the repeater. This digital data signal is injected after transmitter splatter filter stage.
(D0)
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
5
Page 6
Operating Manual Reprint
LINE Interface Port
The VXR-7000 is provided with an 8-pin modular jack
for line interfacing applications. A Western Electric
lar-type RJ45 plug should be used to connect to this jack.
The LINE jack pin-out is shown below.
Note that there are both 4-line and 8-line types of modular
plugs. If a 4-line modular plug is used, only the LINEOUT and LINE IN connections will be made. An 8-line
plug is required to access all lines. In accordance with
standard telecommunications interface, the line connections on the LINE interface jack are impedance balanced,
and are described as follows.
Pins 1 & 2: [RX SQ(+), RX SQ(–)]
(max voltage: 20 V, max current: 7 mA)
An opto-isolator is provided to facilitate E (EAR) signaling. The opto-isolator comes on when a signal exceeding the receiver squelch appears on the receiver
channel (with correct CTCSS tone or DCS code, if enabled). The RX SQ(–) pin is the emitter, and RX SQ(+)
is the collector.
Pins 3 & 4: [LINE IN (Tx Line Audio)]
Analog signals between 300 and 3000 Hz supplied to
this pair are fed to the transmitter when the repeater is
set to the BASE mode (the REPEATER LED is turned
off) and keyed either by the TX KEY input signal (see
below), or by the EXT PTT signal on pin 12 of the rear
panel’s ACC jack. Standard deviation is obtained with
a line level of –10 dBm.
Pins 5 & 6: [LINE OUT (Rx Line Audio)]
Receiver audio is available from this pair, subject to
internal CTCSS or DCS decode if the received signal
strength is above the squelch threshold.
As shipped from the factory, a 1-kHz receiver signal
with standard deviation gives –10 dBm on the line,
but this can be varied by VR4002 and S4001 (on the
repeater’s CNTL Unit).
Pins 7 & 8 [
(max voltage: 20 V, max current: 4 mA)
An opto-isolator is provided to facilitate M (MIC) signaling. That is, a voltage presented to these pins turns
on the opto-isolator and keys the transmitter. The TX
KEY(+) pin is the anode of the opto-isolator, and RX
SQ(–) is the cathode of the opto-isolator.
( ), ( )]
®
modu-
Installation
Antenna Considerations
Repeater operation without a duplexer requires that two
antennas be installed, one for receiving and one for transmitting, so that the receiving antenna does not absorb energy from the transmitting antenna. There are a number of
ways to do this, depending on the TX/RX frequency separation, and on the locations available for antenna mounting. If a duplexer is used, a single antenna suffices for
both transmitting and receiving. If using a reduced-size
duplexer, a six-cavity model (minimum) is recommended.
Vertex Standard recommends the use of the duplexer. For
further details, contact your Vertex Standard dealer.
Regardless of the above choice, it is of paramount importance that the antenna(s) be mounted as high and in the
clear as possible, preferably within line-of-sight to all repeater users. Furthermore, losses in the feedline(s) must
be minimized, so the feedline(s) should be high quality,
and as short as possible. If a long feedline is necessary,
use coaxial “hardline” cable to reduce losses.
Repeater antennas should have an impedance of 50 Ω at
the operating frequency. When separate receive and transmit antennas are used, high-Q narrow-band types may
serve to minimize interaction. However, when a single
antenna is used with a duplexer, it should be a low-Q wideband type.
NEVER TRANSMIT WITHOUT HAVING A
TRANSMIT ANTENNA CONNECTED TO THE
TX ANTENNA JACK OF THE REPEATER.
AC Power Supply Voltage Selection
Each repeater is wired for a particular AC mains voltage
between 100 and 253 VAC. This should be indicated by a
label near the AC jack on the rear panel. If no label is
present, or if the AC voltage on the label is different from
the local AC line, check the wiring inside the Switching
Regulator Unit of the repeater, and change the connections (and label) if necessary, as shown page 8.
Changing the AC input voltage wiring also requires changing the fuse on the FILTER Unit if the voltage is changed
from 100 VAC (100-127 VAC) to 200 VAC (207-253
VAC), or vice-versa. Use a 5-amp fuse for 100 VAC, or a
3-amp fuse for the 200 VAC.
LINE Jack
Modular Jack Pin Numbering
6
Page 7
Operating Manual Reprint
DC Power Supply Backup
For uninterrupted operation during power failures, a 12
volt rechargeable type battery (55-Ah or more recommended) may be connected to the BATT terminal posts
on the rear panel. While the repeater is operating from the
AC source, a slight charging current will maintain battery
charge. In the event of an AC power outage, the automatic power control circuit will automatically switch the
repeater to the backup battery, and operation will not be
interrupted.
After prolonged operation from the battery, it should be
disconnected from the repeater and recharged separately
before re-connecting, as the trickle charge is not sufficient
for recharging a completely discharged battery.
Never reapply AC power to the repeater with a discharged
battery connected, as the DC startup current can damage the repeater and battery.
While operating from a battery or DC supply, the repeater
requires approximately 7 amperes at 12 Volts during transmit.
Equipment Location
While the operating temperature range of the repeater is
quite broad, the best location is one in which the air temperature does not approach the extremes of the specified
range, and one that does not change rapidly. Make sure to
allow for free air flow around the heatsink on the rear apron
at all times. In warm climates, the repeater should not be
sealed in a small closed room.
Protect the repeater from wind and rain, and extremes in
temperature or humidity that may shorten the useful life
of the equipment. Try to locate the repeater in an environment that is also comfortable for service personnel, if possible.
7
Page 8
Operating Manual Reprint
Changing Switching Regulator unit AC Mains Jumper Wiring
Before attempting this jumper wire change, remove the
AC power cord from the AC jack on the rear panel.
Referring to Figure 1, remove the 14 screws affixing
the top and bottom covers of the repeater, and remove
the covers.
Remove the eight screws affixing the shield cover for
the FILTER Unit, and remove the cover (see Figure 1).
Disconnect all wires and connectors from the FILTER
Unit, then remove the six screws affixing the Switching Regulator Unit, and remove it (the Switching Regulator Unit is mounted with the FILTER Unit: Figure
2).
Referring to Figure 3, remove the four screws and re-
move the heatsink from the Switching Regulator Unit.
B
A
Referring to Figure 4, perform the correct jumper wir-
ing on the Switching Regulator Unit for the AC Mains
voltage used in your area (100-127 VAC or 207-253
VAC).
Replace the heatsink onto the Switching Regulator Unit,
then replace the Switching Regulator Unit onto the
chassis, and connect all wires and connectors to the
FILTER Unit.
Replace the shield cover and replace the top and bot-
tom covers. This completes the wiring change.
Important!: If you change the AC voltage range, you must
also change the AC fuse on the FILTER Unit. Do not replace with a slow-blow type fuse.
FILTER Unit
Switching
Regulator
Unit
C
B
C
Figure 2
A
Figure 1
Switching Regulator Unit
Figure 3
Figure 4
8
Page 9
Operating Manual Reprint
CE-27 Programming Software Instruction
With the CE27 Programming Software, you can quickly
and easily program the Vertex Standard VXR-7000
repeater’s channels and configuration from your personal
computer. In the event of an accidental memory failure,
repeater memory and configuration data may be re-loaded
in a matter of minutes.
The CE27 Programming Software diskette contains the
following files:
• CE27.EXE
• CE27.HLP
Before connecting the VXR-7000 for programming, turn
off both the computer and the VXR-7000. Now connect
the VPL-1 Connection Cable to the computer’s serial port
and the VXR-7000.
Then it will be safe to restart the computer; turning off the
equipment during interconnection avoids the potential for
damage to the electronics caused by voltage spikes.
Insert the distribution diskette into your 3½” drive (after
booting DOS), and make a copy of the diskette; use the
distribution diskette for archive purposes, and use the disk
copy for programming.
Place the CE27 (copy) diskette into your 3½” drive (usually “Drive A”), and log onto this drive by typing “A:
[E
NTER]”, then load the contents of the CE27 diskette into
a directory named CE27, using the COPY command (e.g.
“COPY A:*.* C:\CE27”).
Now type “CE27 [E
troductory screen will appear, and you may press any key
to enter the main screen.
Choose the “Help” contents option (F1) from the program’s
Menu for assistance with channel programming or setting
of parameters.
Do not run the CE27 programming software di-
rectly from the original distribution diskette.
Copy the programming software to your
computer's hard disk, then run the software from
the hard disk only. Keep the original distribution diskette in a safe place in case you need to
make another copy of it at a later date.
Before creating the programming data for your
VXR-7000 via the CE27 programming software,
upload the current factory hardware environment data from the VXR-7000, using the [F5]
(ReadRom) command. Use this data profile to
create the programming data for this repeater.
NTER]” to start the program. The in-
Important Note!
VXR-7000 Programming Setup
CE27 Main Screen (Left)
9
Page 10
Operating Manual Reprint
Channel Data Items
Ch: Channel Number
This 2-digit number (01 - 16) is used to identify the channel. Channel numbers occur in sequence, and their order
can not be changed.
Rx Freq.: Edit Receive (or simplex) Frequency
Use the [0] - [9] keys to enter the desired channel frequency directly, and press the [E
CTCSS Decoders: Toggle CTCSS Decoder ON/OFF,
sets CTCSS Frequency
Press the [S
or “off,” or press the [E
PACE] bar to toggle the CTCSS Decoder “on”
NTER] key to display the “TONE
SELECT” window, from which
you may select a CTCSS frequency using the [A
press [E
dow, from which you
may select a DCS code
using the [A
press [E
the [E
RROW] key;
NTER] again to accept the selected code, or press
SC] key to cancel.
W/N: Wide/Narrow Channel Spacing
This function selects the channel spacing environment in
which the VXR-7000 operates.
W (Wide) =25 kHz Channel Spacing, ±5 kHz De-
viation.
N (Narrow) = 12.5 kHz Channel Spacing, ±2.5 kHz
Deviation.
Press the [S
PACE] bar to select the desired channel spac-
ing environment.
Clk Sft: Enable/disable the CPU Clock Shift
This function is only used to move a spurious response
“birdie” should it fall on a current frequency.
Press the [S
PACE] bar to toggle “yes” or “no.”
NTER] key.
NSQ Mode: Noise Squelch Mode
This command selects the manner of setting of the Squelch
threshold level.
User =The squelch threshold level is fixed via the
Prpgm = The squelch threshold level determined via
the dealer programming.
Press the [S
PACE] bar to select the desired NSQ Mode.
NSQ Lv: Noise Squelch threshould level
Use the [0] - [9] keys to enter the desired Squelch threshold level directly, and press the [E
NTER] key. Available
values are 0 (min.) ~ 255 (max.).
Court Blip: Courtesy Blip
When this parameter is set to “on,” this function causes
the VXR-7000 to send out a “blip” on the portable/mobile
radio is frequency each time the portable radio is unkeyed.
This provides audible confirmation to the user that the
VXR-7000 was able to receive the transmission from the
portable.
Press the [S
PACE] bar to toggle “on” or “off.”
Rev Bst: Reverse Burst.
When this parameter is set to “on,” the CTCSS tone
signal’s phase is inverted just before the repeater turns to
receive. This allows the portable/mobile station’s CTCSS
Decoder to begin switching off, thus reducing the transition time required.
Press the [S
PACE] bar to toggle “on” or “off.”
DCS Typ: DCS Format
This command is effective only when DCS is chosen for
squelch control.
A = “Normal” DCS
B = “Inverted” (complement) DCS
Press the [S
PACE] bar to select the desired DCS Type.
DDec Type: DCS Decoder Type
This command selects the manner in which DCS is to be
decoded.
Fixed = Decodes only the type selected in above pa-
rameter (DCS Typ: Normal or Inverted).
Auto = Both types (Normal and Inverted) will be de-
coded.
Press the [S
PACE] bar to select the desired DCS Decoder
Mode.
10
CE27 Main Screen (Scrolled Right)
Page 11
Operating Manual Reprint
Multi Tone: Enable/disable Multi Tone Operation
Press the [S
PACE] bar to toggle Multi Tone Operation be-
tween selections “yes” and “no.”
Press the [E
play the “M
LECT” window, from which
NTER] key to dis-
ULTI TONE SE-
you may select a CTCSS
tone or DCS code; move the
cursol to the appropriate field
you using the [A
open the “T
select the desired CTCSS tone or DCS code using the [A
ROW] key, then press the [ENTER] key again to accept the
selected tone or code, or press the [E
RROW] key, then press the [ENTER] key to
ONE SELECT” or “CODE SELECT” window. Now
R-
SC] key to cancel.
You may set as many as 16 CTCSS tones and/or DCS
codes.
Note that, if you do not yet program a CTCSS tone or
DCS code in the “M
the “M
ULTI TONE SELECT” window data is not pro-
grammed), press the [S
ULTI TONE SELECT” window (when
PACE] bar to display the “MULTI
TONE SELECT” window directly.
CWID ANI/ENI: Select the Identifier modePress the [S
PACE] bar to toggle the selections “CW ID,”
“ANI/ENI,” or “off.” To select this feature to the “CW
ID” or “ANI/ENI,” the “CW ID” parameter must be en-
abled via the dealer programming.
Action Mode: Select the repeater operation mode
Press the [SPACE] bar to toggle between “Duplex” operation or “Simplex” operation.
Tx Freq.: Edit Transmit Frequency
Use the [0] - [9] keys to enter the desired channel frequency directly, and press the [E
NTER] key.
CTCSS Encoders: Toggle CTCSS Encoder ON/OFF,
sets CTCSS Frequency
Press the [S
or “off,” or press the [E
PACE] bar to toggle the CTCSS Encoder “on”
NTER] key to display the “TONE
SELECT” window, from which
you may select a CTCSS frequency using the [A
press [E
dow, from which you
may select a DCS code
using the [A
press [E
the [E
RROW] key;
NTER] again to accept the selected code, or press
SC] key to cancel.
Base TOT: Enable/disable the Time-Out Timer while in
the “BASE” station mode
Press the [S
PACE] bar to toggle the TOT feature selects
“yes” and “no.”
The TOT time is determined via dealer programming.
Base Guard: Enable/disable the Base Guard Feature
When this parameter is set to “yes,” the transmitter will
be inhibited for a few seconds before the repeater (in the
“BASE” station mode) turns to receive.
The inhibit time is determined via dealer programming.
LOUT: Select the Lock Out Feature’s mode
Press the [S
tween “BCLO,” “BTLO,” or “off,” then press the [E
TER] key to accept the setting. “BCLO” inhibits transmit-
PACE] bar to toggle the Lock Out Feature be-
N-
ting while there is carrier present. “BTLO” inhibits transmitting while there is carrier present unless there also is a
valid tone present.
TX Pwr: Transmitter Power Output Selection
This parameter selects the desired power output from the
VXR-7000 on the current channel. The available values
are HIGH and LOW.
Press the [S
PACE] bar to select “Hi” or “Lo.”
TOT Mute: Enable/disable the TOT (Time-Out Timer)
beep monitoring
When this parameter is set to “on,” the alert beep will
sound from the front panel speaker before the repeater
turns itself off.
RptTOT Use: Enable/disable the Time-Out Timer while
operating in the repeater mode
Press the [S
PACE] bar to toggle the Repeater TOT selects
“yes” or “no.”
The TOT time is determined via dealer programming.
RptTOT Beep: Enable/disable the TOT beep Transmis-
sion
Press the [S
PACE] bar to toggle the TOT beep selects “yes”
or “no.”
When this parameter is set to “yes,” the alert beep will be
sent out on the air before the repeater turns itself off, while
oprtating in the “REPEATER” mode.
RPT HT: Enable/disable the Repeater Hang-on Timer
Press the [S
PACE] bar to toggle the Repeater Hang-on Timer
selects “yes” or “no.”
When this parameter is set to “yes,” the repeater will remain keyed for a desired seconds after a receiving carrier
is dropped.
The Hang-up time is determined via dealer programming.
RPT GT: Enable/disable the Repeater Guard
When this parameter is set to “yes,” the transmitter inhibit few second before the repeater is unkeyed.
The inhibit time is determined via dealer programming.
11
Page 12
Operating Manual Reprint
Duplexer Installation
Important Note
Be certain to observe the specifications for Frequency Separation and Maximum Transmitter Power
of the duplexer connected to the VXR-7000. The
Frequency Separation should be 5 MHz (min.) to
10 MHz (max.), and the Maximum TX Power Rating should be at least 40 Watts.
If the VXR-7000 TX output power or frequency
specification is out of the range of the duplexer's
capability, you may re-program the Tx/Rx frequency pair and/or reduce the TX output power of the
VXR-7000, so as to allow temporary operation of
the VXR-7000 until a duplexer of proper ratings
can be obtained.
Please consult with your Authorized Vertex Dealer for assistance with procurement of a suitable
duplexer.
1. Connect the VXR-7000’s TX antenna port to a wattmeter and dummy load (the duplexer must not be connected at this point). Connect any Vertex Standard
microphone to the MIC jack, and place the BASE/REPEATER switch in the “BASE” position. Select
Channel 1 for alignment purposes.
2. Press and hold in the ACCESSORY switch for two
seconds to enter the adjustment mode. The channel
number will begin to blink.
3. Press and hold in the PTT key on the microphone.
The display will indicate “Po” while transmitting. Observe the power output as indicated on the watmeter.
4. Press the (UP: increment) or (DOWN: decrement) button (to the right of the channel display) repeatedly to adjust the TX output power to 40 Watts
(or less) while holding in the PTT key.
5. Once the desired power level has been obtained, release the PTT key. Now press and hold in the AC-CESSORY button for at least two seconds to save
the new setting and exit to the normal operation.
6. Repeat steps 2. through 5. (above) for any other channels (2 through 16) if they are to be used.
7. Re-test each channel in the normal operating mode to
confirm the proper power output. You may now disconnect all test equipment.
8. The duplexer may now be installed.
The above procedure should only be performed by your
Authorized Vertex Standard Dealer or a qualified radio
technician, in order to ensure accurate calibration. Please
consult with your Authorized Vertex Standard Dealer for
assistance with procurement of a suitable duplexer.
12
Page 13
Operating Manual Reprint
Installations
1. Remove the 14 screws affixing the top and bottom
covers of repeater, and remove the covers (Figure 1).
2. Turn the repeater upside down.
3. Referring to Figure 2, remove the upper screw in either side of the front panel, and loosen the lower screw
in either side of the front panel, then slide the front
panel forward slightly.
4. Remove the coaxial cables connected to the TX and
RX antenna jacks of the repeater.
5. Mount the duplexer to the bottom side of the repeater,
using the four screws supplied with the optional Antenna Cable CT-68 (Figure 3).
6. Connect the optional Antenna Cable CT-68 between
the TX antenna jack of the repeater and ANT (center)
jack of the duplexer.
7. If your repeater’s Tx/Rx frequency relationship is “upper shift” type (TXf > RXf), connect the coaxial cable
from the RX Unit to the LOW PASS jack of the duplexer and connect the coaxial cable from the PA Unit
to the HIGH PASS jack of the duplexer.
If your repeater’s Tx/Rx frequency relationship is
“lower shift” type (TXf < RXf), connect the coaxial
cable from the RX Unit to the HIGH PASS jack of the
duplexer and connect the coaxial cable from the PA
Unit to the LOW PASS jack of the duplexer.
Note: Route the TX coaxial cable from the PA Unit as
far as possible from the RX coaxial cable from the RX
Unit.
8. Duplexer installation is now complete. Replace the
front panel back into place, and replace the top and
bottom covers.
Bottom SideTop Side
Figure 1
Figure 2Figure 3
Bottom Side
13
Page 14
Specifications
General
Frequency Range:136 ~ 150 MHz (A) or 150 ~ 174 MHz (C)
Number of Channels:16
Channel Spacing:12.5/25 kHz
Frequency Stability:±2.5 ppm
Antenna Impedance:50 Ω (N-Type)
Tx Activation System:Carrier-operated, CTCSS tone operated, DCS operated, or remote control
Power Requirements:115/230 V AC ±10%, 50/60 Hz or 13.8 VDC
Ambient Temperature Range: –30 °C ~ +60 °C
Dimensions (w/o knobs):325 x 115 x 391.5 mm (12.8 x 4.5 x 15.4 inches)
Weight (approx.):10 kg (22 lbs.)
Receiver
Receiver Type:Double-conversion Superheterodyne
Sensitivity:0.35 µV for 12 dB SINAD, 0.45 µV for 20 dB NQ
Selectivity:75 dB
Intermodulation:75 dB
Spurious & Image Rejection:80 dB
Audio Output:4 W @ 4 Ω
Transmitter
RF Output:10 ~ 50 W (Adjustable)
Duty Cycle:100 %
Maximum Deviation:±5.0 kHz (25 kHz spacing), ±2.5 kHz (12.5 kHz spacing)
Modulation Type:16K0F3E/11K0F3E
Audio Distortion:Less than 2.5 % @ 1 kHz
Spurious Emissions:Better than 75 dB below carrier
Specifications are subject to change without notice.
SCREW JFS-4S-B1WM
TRUSS HEAD SCREW M3×6B
SEMS SCREW HSM4×8
SEMS SCREW HSM3×8
TAPTITE SCREW M3×6
TAPTITE SCREW M3×8
TAPTITE SCREW M3×8
BINDING HEAD SCREW M4×6B
BINDING HEAD SCREW M3×8NI
BINDING HEAD SCREW M3×6
SEMS SCREW HSM3×6NI
SEMS SCREW SM3×8NI
SEMS SCREW SM2.6×6NI
PAN HEAD SCREW M2.6X6NI
PAN HEAD SCREW M3×5
FLAT HEAD SCREW M3×8
SEMS SCREW HM3×30B
SEMS SCREW HSM3×35B
HEX HEAD BOLT M4×8NI
HEXA SOCKET BOLT M4×16B
PLAIN WASHER FW4NI
SPRING LOCK WASHER SW4NI
TOOTHED LOCK WASHER OW4NI
BINDING HEAD SCREW M3×8
(
Lot. 17-
(
Lot. 3-
)
Non-designated parts are available only as
part of a designated assembly.
P1091072
CONNECTOR
Qty.Ref.
2
14
4
2
34
18
1
4
8
6
12
2
2
)
2
2
4
4
1
2
1
1
1
3
RA018270A (Lot. 1~)
RA018270B (Lot. 26~)
FRONT PANEL ASS’Y
RA0180600
KNOB (POW)
RA0180500
VOLUME KNOB
N4090143
PUSH SWITCH
RA0181500
PANEL FRAME
RA0180800
SHIELD CASE COVER (RF)
Display Unit
KEY Unit
RA0180700
PUSH KNOB (4pcs)
RX Unit
VOL Unit
SQL Unit
TX Unit
M4090066
SPEAKER
RA0065800
RUBBER HOLDER (SP)
RA0181200
HOLDER (MJ)
R3054370
FOOT (4pcs)
P1091073
CONNECTOR
P9090014
M2090032
FAN
RA0180000 (Lot. 1~)
RA018000A (Lot. 19~)
CHASSIS
P1090654
CONNECTOR
RA0181400
BOTTOM CASE
CONNECTOR (2pcs)
PA Unit
15
Page 16
Exploded View & Miscellaneous Parts
Note:
16
Page 17
Block Diagram
17
Page 18
Block Diagram
18
Page 19
Block Diagram
19
Page 20
Interconnection Diagram
20
Page 21
Circuit Description
Receive Signal Path
Incoming RF from the RX antenna jack is delivered to the
RX Unit and passes through the protection diode D3001
(MA143) and a varactor-tuned band pass filter consisting of
coils L3002 and L3004, capacitors C3019, C3021, C3024,
C3027, and C3028, and diodes D3004 and D3008 (both
HVU350). Signals are then applied to the RF amplifier, Q3008
(2SC3357). The amplified RF signal is applied through a varactor-tuned band pass filter consisting of coils L3009 and L3012,
capacitors C3053, C3054, C3059, C3060, and C3065, and diodes D3012 and D3013 (both HVU350) to the first mixer D3014
(GN2011-Q) along with the first local signal from the PLL
circuit.
The first local signal is generated between 114.6 MHz and
152.6 MHz by the RX VCO, which consists of FET Q3007
(2SK508) and varactor diodes D3005, D3006, D3009, and
D3010 (HVU350) according to the programmed receiving fre-
quency; the local signal then passes through buffer amplifier
Q3009 (2SC5226) and first local amplifier Q3011 (2SC3357)
to the first mixer D3014.
The 21.4 MHz first IF signal is applied to monolithic crys-
tal filters XF3001 and XF3002 (both 21M10B1: ±10 kHz B.W.)
which strip away unwanted mixer products, and the IF signal is
applied to the first IF amplifier Q3016 (2SC2620QB). The
amplified first IF signal is then delivered to the FM IF subsystem IC Q3012 (TA31136FN), which contains the second
mixer, second local oscillator, limiter amplifier, noise amplifier, and FM detector.
The second local oscillator signal, generated by the 20.945
MHz crystal X3002, produces the 455 kHz second IF signal
when mixed with the first IF signal within Q3021. The second
IF signal passes through ceramic filter CF3001 (CFWM455G:
±4.5 kHz B.W.) or CF3002 (CFWM455F: ±6.0 kHz B.W.)
which strips away all but the desired signal, and then passes
through the limiter amplifier within Q3021 to ceramic discriminator CD3001 (CDB455C7), which removes any amplitude
variations in the 455 kHz IF signal before detection of speech.
The detected audio passes through the low pass filter, consisting of R3067 and C3115, which rejects the 455 kHz IF component, then delivers the audio to pin 12 of JP3001.
The audio signal from the RX Unit is delivered to the CNTL
Unit and passes through the audio amplifier Q4014-3
(NJM2902M) to the active high pass filter section of Q4024
(FX-805) which rejects the sub-audible frequency component.
The filtered audio signal is delivered to potentiometer VR4001,
which adjusts the audio sensitivity to compensate for audio level
variations, then passes through audio amplifier Q4014-2
(NJM2902M), audio switch Q4030 (NJU4066BM), a 20 dB
attenuator consisting of R4180 and R4211, and limiter amplifier Q4018-2 (NJM2902M), to the electronic volume control
Q4029 (M51132FP), where the maximum deviation is set. The
audio signal subsequently passes through the a 3-section active
low pass filter consisting of Q4019-1/-2/-3 (NJM2902M) and
audio amplifier Q4019-4 to J4008’s pin 10, providing the repeater transmit audio.
A portion of the audio signal from the active high pass filter
section of Q4024 is de-emphasized by Q4020-1 (NJM2902M),
providing a flat audio response. The filtered audio then passes
through the active band pass filter Q4016 (NJM2902M) and
audio mute gate Q4038 (DTC323TK) to audio power amplifier Q4043 (TDA2003H), providing up to 2 Watts of audio power
to the 8 Ω loudspeaker.
Sub-Audible Signaling (Decoder)
A portion of the audio signal from the audio amplifier
Q4014-1 passes through the active low pass filter at Q4014-2
and the low pass filtering section of Q4024 to separate the subaudible tones from the received audio signal. The sub-audible
tones are sent to the CTCSS/DCS decoder section of Q4024.
When a CTCSS tone or DCS code is received, the CTCSS or
DCS information is delivered to pin 20 of the Main CPU Q4012
from pin 4 of Q4024, which compares the CTCSS tone or DCS
code with the programmed tone or code data. If the received
CTCSS tone or DCS code matches the programmed tone or
code, pin 39 of the Main CPU Q4012 goes low, turning on the
squelch switch Q4036 (DTC323TK) and passing the received
audio signal to the audio power amplifier, Q4043.
Squelch Control
The squelch circuit consists of noise amplifier Q3014
(2SC4116) and noise detector D3018 (MA143) on the RX
Unit, and control circuitry within main microprocessor Q4012
on the CNTL Unit.
When no carrier is received, noise at the output of the audio
detector stage of Q3012 is amplified by Q3014 (2SC4116GR),
and then rectified by D3018 (MA143) to provide a DC control
voltage for the squelch switch. The resulting DC voltage is delivered to pin 6 of JP3001.
The DC voltage from the RX Unit is delivered to the A-D
analog input port (pin 31) of the Main CPU Q4012
(HD64F3337YF16) on the CNTL Unit, which compares the
squelch threshold level to that which is memorized in EEPROM
Q4008 (NM93C86A) or set by the front panel SQL control.
RX PLL and VCO Circuits
The receiver’s PLL circuitry consists of PLL subsystem
IC Q3001 (MB15A02PFV1) on the RX Unit, which contains
a reference oscillator/divider, serial-to-parallel data latch, programmable divider, phase comparator and a swallow counter.
Stability is obtained by a regulated 5 VDC supply via Q3021
(TA78L05) and the temperature-compensated temperature compensated 14.4 MHz crystal oscillator X3001 via thermistor
TH3001 and TH3002.
The RX VCO, consisting of FET Q3007 and varactor diodes D3005, D3006, D3009, and D3010, oscillates between
114.6 MHz and 152.6 MHz according to the programmed re-
21
Page 22
Circuit Description
ceiving frequency. The RX VCO output passes through buffer
amplifier Q3009 and first local amplifier Q3011 to the first mixer
D3014, as described previously. A portion of the RX VCO output is applied to the prescaler/swallow counter section in the
PLL IC, Q3001. There the RX VCO signal is divided by 64 or
65, according to a control signal from the Main CPU Q4012 on
the CNTL Unit, before being applied to the programmable divider section of the PLL IC Q3001.
The data latch section of the PLL IC Q3001 also receives
serial dividing data from the Main CPU Q4012, which causes
the pre-divided RX VCO signal to be further divided by 22,920
~ 30,520 in the programmable divider section in the PLL IC
Q3001, depending upon the desired receive frequency, so as to
produce a 5 kHz or 6.25 kHz derivative of the current RX VCO
frequency. Meanwhile, the reference divider section of the PLL
IC Q3001 divides the 14.4 MHz crystal reference from the reference oscillator X3001 and Q3002 (2SC4116GR) by 2880
(or 2304) to produce the 5 kHz (or 6.25 kHz) loop reference.
The 5 kHz or 6.25 kHz signal from the programmable divider (derived from the RX VCO) and that derived from the
crystal are applied to the phase detector section of the PLL IC
Q3001, which produces a pulsed output with pulse duration
depending on the phase difference between the input signals.
This pulse train is then converted to DC, low pass filtered, then
fed back to the RX VCO varactor diodes D3005, D3006, D3009,
and D3010.
Changes in the DC voltage applied to the varactor diodes
D3005, D3006, D3009, and D3010 affect the reactance in the
tank circuit RX VCO Q3007, changing the oscillating frequency according to the phase difference between the signals derived from the RX VCO and the crystal reference oscillator.
The RX VCO is thus phase-locked to the reference frequency
standard.
Transmit Signal Path
The TX VCO, consisting of FET Q2005 (2SK508) and var-
actor diodes D2004 and D2005, oscillates between 136 MHz
and 174 MHz according to the programmed transmit frequency. The theory of operation of the remainder of the PLL circuitry is similar to that of the RX PLL circuit; however, dividing
data from the Main CPU Q4012 on the CNTL Unit is such that
the VCO frequency is the actual transmit frequency.
The speech audio from the CNTL Unit is applied to varactor diode D2005 (HVU350), which frequency modulates the
TX VCO up to ±5 kHz (wide band) or ±2.5 kHz (narrow band)
from the unmodulated carrier at the transmit frequency. The
modulated transmit signal is buffered by Q2008 (2SC5226),
then passes through the RF amplifier Q2010 (2SC3357) and
RF diode switch D2008 (RN739F) to the PA Unit.
The transmit signal is applied to the RF amplifier Q1501
(2SC3357) and RF power module IC Q1502 (PF0310A), then
finally amplified by power amplifier Q1507 (2SC5125) up to
50 Watts. Harmonic and spurious radiation in the final output
is suppressed by a low pass filter consisting of coils L1511 ~
L1515, plus capacitors C1546, C1547, C1554, C1556, C1560,
and C1566 on the PA Unit, before delivery to the TX antenna
jack.
APC (Automatic Power Control)
RF power output from the final amplifier Q1507 is sampled
by C1548/C1558 and is then rectified by D1503/D1504 (both
1SS319). The resulting DC voltage is applied to the comparator Q1509 (TA75S01F), where the voltage is compared with a
reference voltage from the Main CPU Q4012 on the CNTL
Unit, to produce a control voltage for the Automatic Power Controller Q1503 (2SB1122S) and Q1504 (2SC4116GR), which
regulates supply voltage to the RF power module IC Q1502, so
as to maintain stable high (or low) output power under varying
antenna loading conditions.
CONTROL (CNTL) Unit
The CNTL Unit consists of 8-bit CPU Q4012
(HD64F3337YF16), EEPROM Q4008 (NM93C86A), RX and
TX speech audio circuits, and various analog switches for the
CPU and repeater interconnections.
Microprocessor operational code is stored in Q4008, while
channel data and repeater configuration information is programmed from an external PC connected to the front panel’s
MIC jack via a VPL-1 programming cable.
The output from the Main CPU, Q4012, contains serial control data used for REPEATER/BASE mode control, as well as
TX and RX PLL data. Crystal X4001 oscillates at 16 MHz, and
provides stable clock timing for the Main CPU. When the repeater is powered on, the voltage at pin 8 of Q4012 becomes
stable, and the output of voltage detector IC Q4005
(RH5VL45AA), which is tied to Q4012 (pin 1-RST) becomes
high, resetting the Main CPU.
Base Operation (Tx, Line-Input Audio)
Line input from J4009 (pins 3 and 4) is impedance matched
by transformer T4001, then passes through the audio amplifier
Q4018 (NJM2902M) and audio switch Q4030 (NJU4066BM)
to the pre-emphasis network at Q4018-1, where the signal is
processed in the same manner as previously described. The line
level can be attenuated by switch S4002, and line sensitivity
can be adjusted to –10 dBm ~ +10 dBm by potentiometer
VR4003 to compensate for audio line level variations.
Base Operation (Tx, Mic-Input Audio)
Microphone input is delivered past the MIC MUTE switch
Q4026 (DTC323TK), then passes through the audio amplifier
and active low pass filter at Q4021 (NJM2902M) to the pre-
emphasis network at Q4018-1, where the signal is processed in
the same manner as previously described.
22
Page 23
Alignment
The VXR-7000 is carefully aligned at the factory for
the specified performance across the entire operating frequency range. Realignment should therefore not be necessary except in the event of a component failure. All component replacement and service should be performed only
by an authorized Vertex Standard representative, or the
warranty policy may be void.
The following procedures cover the sometimes critical
and tedious adjustments that are not normally required once
the repeater has left the factory. However, if damage occurs and some parts subsequently are placed, realignment
may be required. If a sudden problem occurs during normal operation, it is likely due to component failure; realignment should not be done until after the faulty component has been replaced.
We recommend that servicing be performed only by
authorized Vertex Standard service technicians who are
experienced with the circuitry and fully equipped for repair and alignment. Therefore, if a fault is suspected, contact the dealer from whom the repeater was purchased for
instructions regarding repair. Authorized Vertex Standard
service technicians realign all circuits and make complete
performance checks to ensure compliance with factory
specifications after replacing any faulty components.
Those who do undertake any of the following alignments are cautioned to proceed at their own risk. Problems caused by unauthorized attempts at realignment are
not covered by the warranty policy. Also, Vertex Standard
reserves the right to change circuits and alignment procedures in the interest of improved performance, without
notifying owners.
Under no circumstances should any alignment be attempted unless the normal function and operation of the
repeater are clearly understood, the cause of the malfunction has been clearly pinpointed and any faulty components replaced, and realignment determined to be absolutely necessary.
The following test equipment (and thorough familiarity with its correct use) is necessary for complete realignment. Correction of problems caused by misalignment
resulting from use of improper test equipment is not covered under the warranty policy. While most steps do not
require all of the equipment listed, the interactions of some
adjustments may require that more complex adjustments
be performed afterwards.
Do not attempt to perform only a single step unless it
is clearly isolated electrically from all other steps. Have
all test equipment ready before beginning, and follow all
of the steps in a section in the order presented.
Required Test Equipment
RF Signal Generator with calibrated output level at 200
MHz
Deviation Meter (linear detector)
In-line Wattmeter with 5% accuracy at 200 MHz
50 Ω RF Dummy Load with power rating 100W at
200MHz
4 Ω AF Dummy Load
Frequency Counter with 0.2 ppm accuracy at 200MHz
AF Signal Generator
AC Voltmeter
DC Voltmeter: High input impedance
VHF Sampling Coupler
SINAD Meter
IBM PC/compatible Computer with MS-DOS or later
operating system
Yaesu VPL-1 Connection Cable & CE27 Channel/
Alignment Diskette
Alignment Preparation & Precautions
A 50 Ω RF Dummy Load and in-line wattmeter must
be connected to the TX antenna jack in all procedures that
call for transmission, except where specified otherwise.
Correct alignment is not possible with an antenna.
After completing one step, read the following step to
determine whether the same test equipment will be required. If not, remove the test equipment (except dummy
load and wattmeter, in connected) before proceeding.
Correct alignment requires that the ambient temperature be the same as that of the repeater and test equipment,
and that this temperature be held constant between 68° F
~ 86° F (20° C ~ 30° C). When the repeater is brought into
the shop from hot or cold air, it should be allowed time to
come to room temperature before alignment.
Whenever possible, alignments should be made with
oscillator shields and circuit boards firmly affixed in place.
Also, the test equipment must be thoroughly warmed up
before beginning.
Note: Signal levels in dB referred to in the alignment pro-
cedure are based on 0 dBµ = 0.5 µV (closed cir-
cuit).
23
Page 24
Alignment
Set up the test equipment as shown below, and apply
AC power to the repeater.
The repeater must be programmed for use in the intended system before alignment is attempted. The frequency and other parameters are loaded from the file during the alignment process.
In order to facilitate alignment over the complete
switching range of the equipment it is recommended that
the channel data first be uploaded and then stored to disk.
Channels at the upper, lower and middle band edges should
then be downloaded. The original data can be replaced at
the end of the alignment process.
ChannelFrequency (MHz)
TYP CTYP A
Low band edge150.000136.000
Mid 1160.000140.000
Center162.000143.000
Mid 2170.000145.000
High band edge174.000150.000
Transmitter
Press the BASE/REPEATER switch on the front panel
of the repeater so as to set it to the “BASE” mode if the
REPEATER LED is on. You should see the REPEATER
LED turn off, indicating that the repeater is now in the
“BASE” mode.
PLL VCV (Varactor Control Voltage) Check
Connect the DC voltmeter between the VCV check
point (on the TX Unit) and chassis ground.
Select the Low band edge channel, then key the re-
peater. Confirm that the DC voltmeter reading is 1.7 V
~ 2.4 V (TYP C) or 1.6 V ~ 2.2 V (TYP A).
Select the High band edge channel, then key the re-
peater. Confirm that the DC voltmeter reading is 3.9 V
~ 5.3 V (TYP C) or 3.0 V ~ 4.0 V (TYP A).
PLL Reference Frequency Adjustment
Connect the Frequency counter to J2001 on the TX
Unit.
Select the Center channel, then key the repeater.
Adjust TC2001 (on the TX unit), if necessary, so that
the frequency counter reading is within ±100 Hz of the
programmed Center channel frequency.
Alignment Setup
Transmitter parameters (excluding PLL)
The following transmitter parameters can be adjusted
from the computer by utilizing the CE27 Channel/
Alignment Diskette. Refer to the onboard help of the
CE27 Channel/Alignment Diskette for details.
First ensure that the “DUPLEX” mode of operation is
enabled via CE27 programming.
Set the BASE/REPEATER switch on the front panel
of the repeater to the “REPEATER” mode (the RE-
PEATER LED will turn on).
Inject a signal on the Center channel frequency at a
level of 40 dBµ (1 kHz tone @ ±3 kHz deviation) from
the RF Signal Generator into the RX antenna jack, and
adjust VR4001 (on the CNTL Unit) so that the devia-
tion meter reading (TX deviation) is ±3.0 kHz (±0.3
kHz) deviation.
Base Mode
Alignment Setup
Set the BASE/REPEATER switch on the front panel
of the repeater to the “BASE” mode (the REPEATER
LED will turn off).
Press the LOCAL/REMOTE switch on the front panel
of the repeater to the “REMOTE” mode (the RE-MOTE LED will turn on).
Set S4001 and S4002 (on the CNTL Unit) to the
“OFF” position, then select the Center channel.
Audio Level Adjustment (LINE OUT Level)
Inject a signal on the Center channel frequency at a
level of 40 dBµ (1 kHz tone @ ±3.5 kHz deviation)
from the RF Signal Generator into the RX antenna jack,
and adjust VR4002 (on the CNTL Unit) so that the
“Line Out” audio level (LINE jack pins 5 and 6) is –10
dBm (±0.5 dBm).
Deviation Adjustment (LINE IN Level)
Connect the AF generator to LINE jack pins 3 and 4,
and the AF generator output level to –10 dBm, at a
frequency of 1 kHz.
Key the repeater, and adjust VR4003 (on the CNTL
Unit) so that the deviation meter reading (TX deviation) is 3.0 kHz (±0.1 kHz) deviation.
26
Page 27
Circuit Diagram
PA Unit
27
Page 28
PA Unit
Parts Layout
1
2
ABCDEFGHI
3
Side A
2SC5125
(Q1507)
PF0314 (TYP C)
PF0313 (TYP A: Lot. 7~)
(Q1502)
28
Page 29
PA Unit
abcdefghi
1
2
3
Side B
TA75S01F (SA)
(Q1509)
NJM78L09UA (8H)
(Q1508)
UN5213 (8C)
(Q1506)
2SB1122S (BE)
(Q1503, 1505)
2SC3357 (RK)
(Q1501)
2SC4116GR (LG)
(Q1504)
1SS319 (A4)
(D1503, 1504)
MA143 (MC)
(D1502)
RN739F (5F)
(D1501)
29
Page 30
PA Unit
Note:
30
Page 31
PA Unit
Parts List
REF
C 1501 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bi3
C 1503 CHIP CAP.56pF50VCHGRM39CH560J50PTK221742291-Bi2
C 1504 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bi2
C 1505 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Bi2
C 1506 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bi2
C 1507 CHIP CAP.39pF50VCHGRM39CH390J50PTK221742251-AA2
C 1508 CHIP CAP.15pF50VCHGRM39CH150J50PTK221742151-6AB2
C 1508 CHIP CAP.18pF50VCHGRM39CH180J50PTK22174217 VERSION A 7-AB2
C 1508 CHIP CAP.15pF50VCHGRM39CH150J50PTK22174215 VERSION C 7-AB2
C 1509 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bh2
C 1510 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-18Bh2
C 1512 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Bh3
C 1513 CHIP CAP.0.001uF50VBGRM40B102M50PTK221708051-Bh2
C 1514 CHIP CAP.0.01uF50VBGRM40B103M50PTK221708171-Bh2
C 1515 CHIP CAP.1uF25VW5RCM32W5R105K25ATK221458011-AB2
C 1515 CHIP CAP.1uF50VBGRM42-2B105K50PTK2217580119-AB2
C 1516 CHIP CAP.1uF10VBGRM40B105K10PTK221008021-Bh2
C 1517 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bh2
C 1518 CHIP CAP.0.001uF50VBGRM40B102M50PTK221708051-Bg2
C 1519 CHIP CAP.0.01uF50VBGRM40B103M50PTK221708171-Bg2
C 1520 CHIP CAP.1uF25VW5RCM32W5R105K25ATK221458011AB2
C 1521 CHIP CAP.12pF500VCHGRM42-6CH120J500PTK222712151-6AC2
C 1521 CHIP CAP.8pF500VCHGRM42-6CH080D500PTK22271211 VERSION A 7-AC2
C 1521 CHIP CAP.12pF500VCHGRM42-6CH120J500PTK22271215 VERSION C 7-AC2
C 1522 CHIP CAP.47pF500VCHGRM42-6CH470J500PTK222712291-6AD2
C 1522 CHIP CAP.56pF500VCHGRM42-6CH560J500PTK22271231 VERSION A 7-AD2
C 1522 CHIP CAP.47pF500VCHGRM42-6CH470J500PTK22271229 VERSION C 7-AD2
C 1523 CHIP CAP.5pF500VCHGRM42-6CH050C500PTK222712081-6AD2
C 1523 CHIP CAP.5pF500VCHGRM42-6CH050C500PTK22271208 VERSION C 19-AD2
C 1523 CHIP CAP.3pF500VCJGRM42-6CJ030C500PTK22271206 VERSION A 7-AD2
C 1523 CHIP CAP.5pF500VCHGRM42-6CH050C500PTK22271208 VERSION C 7-18AD2
C 1524 FILM CAP.390pF500VUC342H3900J-TK332790401-6AD2
C 1524 FILM CAP.180pF500VUC342H1800J-TK33279039 VERSION A 38-AD2
C 1524 FILM CAP.180pF500VUC342H1800J-TK33279039 VERSION A 7-37AD2
C 1524 FILM CAP.390pF500VUC342H3900J-TK33279040 VERSION C 7-AD2
C 1525 FILM CAP.220pF500VUC342H2200J-TK332790111-6AD2
C 1525 FILM CAP.270pF500VUC342H2700J-TK33279013 VERSION A 38-AD2
C 1525 FILM CAP.270pF500VUC342H2700J-TK33279013 VERSION A 7-37AD2
C 1525 FILM CAP.220pF500VUC342H2200J-TK33279011 VERSION C 7-AD2
C 1526 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-Bi2
C 1527 FILM CAP.120pF500VUC342H1200J-TK332790261-6AD2
C 1527 FILM CAP.270pF500VUC342H2700J-TK33279013 VERSION A 38-AD2
C 1527 FILM CAP.120pF500VUC342H1200J-TK33279026 VERSION C 19-AD2
C 1527 FILM CAP.270pF500VUC342H2700J-TK33279013 VERSION A 7-37AD2
C 1527 FILM CAP.120pF500VUC342H1200J-TK33279026 VERSION C 7-18AD2
C 1528 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Bi1
C 1529 FILM CAP.82pF500VUC232H0820J-TK332790331-6AE1
C 1529 FILM CAP.100pF500VUC232H1000J-TK33279048 VERSION A 7-AE1
C 1529 FILM CAP.82pF500VUC232H0820J-TK33279033 VERSION C 7-AE1
C 1530 CHIP CAP.120pF300VCGC17CG121K3TXLTK222532051-6AE2
C 1530 CHIP CAP.120pF300VCGC17CG121K3TXLTK22253205 VERSION C 19-AE2
C 1530 CHIP CAP.150pF300VCGC17CG151K3TXLTK22253204 VERSION A 7-AE2
C 1530 CHIP CAP.150pF300VCGATC700B151KW300XTK22253207 VERSION A 18-AE2
C 1530 CHIP CAP.120pF300VCGC17CG121K3TXLTK22253205 VERSION C 7-18AE2
C 1531 FILM CAP.82pF500VUC232H0820J-TK332790331-6AE1
C 1531 FILM CAP.82pF500VUC232H0820J-TK33279033 VERSION C 19-AE1
C 1531 FILM CAP.100pF500VUC232H1000J-TK33279048 VERSION A 7-AE1
C 1531 FILM CAP.82pF500VUC232H0820J-TK33279033 VERSION C 7-18AE1
C 1532 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Bi1
C 1533 AL.ELECTRO.CAP.1000uF25VRJ3-25V102M 1000UFK401490411-AG1
DESCRIPTION
PCB with ComponentsCS1645001 VERSION C
Printed Circuit BoardFR003510C1-
VALUEV/WTOLVXSTD P/NMFR’S DESIGVERS
CS1645002 VERSION A
SIDE LAY ADR
LOT
31
Page 32
PA Unit
REF.
C 1534 AL.ELECTRO.CAP.1000uF25VRJ3-25V102M 1000UFK401490411AD1
C 1534 AL.ELECTRO.CAP.1000uF25VRJ3-25V102M 1000UFK401490412-AD1
C 1535 CHIP CAP.0.001uF500VW5RGRM42-6W5R102K500PTK222718011-Bd1
C 1536 CHIP CAP.0.01uF200VX7RGRM42-6X7R103K200PTK222318021-Bd1
C 1537 CHIP CAP.1uF25VW5RCM32W5R105K25ATK221458011-AF1
C 1537 CHIP CAP.1uF50VBGRM42-2B105K50PTK2217580119-AF1
C 1538 CHIP CAP.0.001uF500VW5RGRM42-6W5R102K500PTK222718011-Bd1
C 1539 CHIP CAP.0.01uF200VX7RGRM42-6X7R103K200PTK222318021-Bc1
C 1540 FILM CAP.82pF500VUC232H0820J-TK33279033 VERSION A 7-AF2
C 1541 FILM CAP.68pF500VUC232H0680J-TK332790301-6AF2
C 1541 FILM CAP.8pF500VUC232H0080D-TK33279005 VERSION A 38-AF2
C 1541 FILM CAP.68pF500VUC232H0680J-TK33279030 VERSION C 19-AF2
C 1541 FILM CAP.8pF500VUC232H0080D-TK33279005 VERSION A
C 1541 FILM CAP.68pF500VUC232H0680J-TK33279030 VERSION C 7-18AF2
C 1542 FILM CAP.12pF500VUC232H0120J-TK332790201-6AF2
C 1542 FILM CAP.9pF500VUC232H0090D-TK33279047 VERSION A 38-AF2
C 1542 FILM CAP.12pF500VUC232H0120J-TK33279020 VERSION C 19-AF2
C 1542 FILM CAP.9pF500VUC232H0090D-TK33279047 VERSION A 7-37AF2
C 1542 FILM CAP.12pF500VUC232H0120J-TK33279020 VERSION C 7-18AF2
C 1543 FILM CAP.100pF500VUC342H1000J-TK332790311-AG2
C 1544 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg3
C 1546 FILM CAP.15pF500VUC232H0150J-TK332790281-6AG2
C 1546 FILM CAP.18pF500VUC232H0180J-TK33279029 VERSION A 38-AG2
C 1546 FILM CAP.18pF500VUC232H0180J-TK33279029 VERSION A 7-37AG2
C 1546 FILM CAP.15pF500VUC232H0150J-TK33279028 VERSION C 7-AG2
C 1547 FILM CAP.27pF500VUC232H0270J-TK332790231-6AG2
C 1547 FILM CAP.33pF500VUC232H0330J-TK33279024 VERSION A 7-AG2
C 1547 FILM CAP.27pF500VUC232H0270J-TK33279023 VERSION C 7-AG2
C 1548 CHIP CAP.1pF50VCKGRM40CK010C50PTK221702021-18Bc2
C 1549 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg3
C 1550 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg2
C 1552 CHIP CAP.1pF50VCKGRM40CK010C50PTK221702021-Bb2
C 1553 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bc2
C 1554 FILM CAP.27pF500VUC232H0270J-TK332790231-6AH2
C 1554 FILM CAP.47pF500VUC232H0470J-TK33279034 VERSION A 7-AH2
C 1554 FILM CAP.27pF500VUC232H0270J-TK33279023 VERSION C 7-AH2
C 1556 FILM CAP.27pF500VUC232H0270J-TK332790231-6AH1
C 1556 FILM CAP.33pF500VUC232H0330J-TK33279024 VERSION A 7-AH1
C 1556 FILM CAP.27pF500VUC232H0270J-TK33279023 VERSION C 7-AH1
C 1557 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb2
C 1558 CHIP CAP.1pF50VCKGRM40CK010C50PTK221702021-Bb2
C 1559 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg3
C 1560 FILM CAP.15pF500VUC232H0150J-TK332790281-6AI2
C 1560 FILM CAP.18pF500VUC232H0180J-TK33279029 VERSION A 7-AI2
C 1560 FILM CAP.15pF500VUC232H0150J-TK33279028 VERSION C 7-AI2
C 1561 FILM CAP.470pF500VUC342H4700J-TK332790151-Ba2
C 1562 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bf3
C 1563 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg3
C 1564 AL.ELECTRO.CAP.1000uF25VRJ3-25V102M 1000UFK401490411-AG1
C 1565 CHIP CAP.0.01uF50VBGRM40B103M50PTK221708171-Bi2
C 1566 FILM CAP.27pF500VUC232H0270J-TK332790231-6AH2
C 1566 FILM CAP.33pF500VUC232H0330J-TK33279024 VERSION A 7-AH2
C 1566 FILM CAP.27pF500VUC232H0270J-TK33279023 VERSION C 7-AH2
C 1567 FILM CAP.56pF500VUC232H0560J-TK332790351-6
C 1567 FILM CAP.68pF500VUC232H0680J-TK33279030 VERSION A 38C 1567 FILM CAP.56pF500VUC232H0560J-TK33279035 VERSION C 19C 1567 FILM CAP.68pF500VUC232H0680J-TK33279030 VERSION A 7-37
C 1567 FILM CAP.56pF500VUC232H0560J-TK33279035 VERSION C 7-18
C 1568 FILM CAP.470pF500VUC342H4700J-TK332790151-6
C 1568 FILM CAP.470pF500VUC342H4700J-TK33279015 VERSION C 19C 1568 FILM CAP.470pF500VUC342H4700J-TK33279015 VERSION C 7-18
D 1501 DIODERN739F T106G20706261-Bi2
D 1502 DIODEMA143-(TX)G20705361-Bi2
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
23-37
AF2
32
Page 33
PA Unit
REF.
D 1503 DIODE1SS319 TE85RG20700801-Bb2
D 1504 DIODE1SS319 TE85RG20700801-Bb2
FB1501 M.RFCFBA03VA450AB-00L11903891-AB2
FB1502 FERRITE BEADS4A2 RI3X3-1L91900011FB1503 FERRITE BEADS4A2 RI3X3-1L91900011J 1501 CONNECTORTMP-J01X-V6P10902101-AA2
JP1501 WIRE ASSYA1367+T92067901-AC3
JP1502 WIRE ASSYA1367+T9206787A1-18
JP1502 WIRE ASSYA1367+T9206787A19JP1503 WIRE ASSYRED 230 FV2/(3)T93181181-18AF1
JP1503 WIRE ASSYRED 230 FV2/(3)T931811819-AF1
JP1504 WIRE ASSYBLK 240 FV2/(3)T93181191-18AF1
JP1504 WIRE ASSYBLK 240 FV2/(3)T931811919-AF1
L 1501 M.RFC0.022uHHK2125 22NK-TL16903811-Bi2
L 1502 M.RFC0.056uHHK2125 56NK-TL16903861-Bh2
L 1503 COIL A14.5T4.5D0.8UEW RL0021907A1AB2
L 1504 COIL A15.5T2.5D0.5UEW RL0021808A1-22AC2
L 1504 COIL A14.5T2.5D0.5UEW RL0021807A VERSION A 23-AC2
L 1504 COIL A15.5T2.5D0.5UEW RL0021808A VERSION C 23-AC2
L 1505 COIL A12.5T3.0D0.6UEW RL0021811A1-AC2
L 1506 COIL A18.5T3.0D0.5UEW RL0020724A1-AD2
L 1507 COIL A13.5T5.0D1.2UEW RL00221301-AF1
L 1508 COIL A13.5T5.0D1.2UEW RL00221301-AF1
L 1509 COIL A11.5T3.0D1.2UEW RL00221521-AF2
L 1510 COIL A11.5T5.0D1.2UEW RL00221631-AF2
L 1511COIL A13.5T6.0D1.2UEW RL00226141-AG2
L 1512 COIL A13.5T6.0D1.2UEW RL00226141-AG2
L 1513 COIL A13.5T6.0D1.2UEW RL00226141-AH2
L 1514 COIL A13.5T6.0D1.2UEW RL00226141-AI2
L 1515 COIL A13.5T6.0D1.2UEW RL00226141-AH1
Q 1501 TRANSISTOR2SC3357-T2 RFG3333577F1-Bi2
Q 1502 ICPF0313-04G1092949 VERSION A 7-AA1
Q 1502 ICPF0314-04G1092850 VERSION C 1-AA1
Q 1503 TRANSISTOR2SB1122S-TDG3211228S1-Bh2
Q 1504 TRANSISTOR2SC4116GR TE85RG3341167G1-Bh2
Q 1505 TRANSISTOR2SB1122S-TDG3211228S1-Bh3
Q 1506 TRANSISTORUN5213-(TX)G30701921-Bh3
Q 1507 TRANSISTOR2SC2630G3326300 25W19-AE2
Q 1507 TRANSISTOR2SC5125-21G3351250 50W1-AE2
Q 1508 ICNJM78L09UA TE2G10913051-Bi1
Q 1509 ICTA75S01F TE85RG10915931-Bg3
R 1501 CHIP RES.2701/16W 5%RMC1/16 271JATPJ241852711-Bi2
R 1502 CHIP RES.2701/16W 5%RMC1/16 271JATPJ241852711-Bi2
R 1503 CHIP RES.5.6k1/16W 5%RMC1/16 562JATPJ241855621-Bi3
R 1504 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-Bi2
R 1505 CHIP RES.4.71/10W 5%RMC1/10T 4R7JJ242054791-Bi2
R 1506 CHIP RES.1.5k1/16W 5%RMC1/16 152JATPJ241851521-Bi2
R 1507 CHIP RES.1.5k1/16W 5%RMC1/16 152JATPJ241851521-Bi2
R 1508 CHIP RES.4701/10W 5%RMC1/10T 471JJ242054711-AB2
R 1509 CHIP RES.101/10W 5%RMC1/10T 100JJ242051001-AB2
R 1510 CHIP RES.4701/10W 5%RMC1/10T 471JJ242054711-AB2
R 1511 CHIP RES.4701/16W 5%RMC1/16 471JATPJ241854711-AB2
R 1512 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AB2
R 1513 CHIP RES.2.2k1/16W 5%RMC1/16 222JATPJ241852221-Bh2
R 1514 CHIP RES.221/16W 5%RMC1/16 220JATPJ241852201-Bh2
R 1515 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-Bh2
R 1516 CHIP RES.2.2k1/16W 5%RMC1/16 222JATPJ241852221-Bh3
R 1517 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bh3
R 1519 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-Bh3
R 1520 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-Bh3
R 1521 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bg2
R 1522 CHIP RES.100k1/16W 5%RMC1/16 104JATPJ241851041-Bg3
R 1523 CHIP RES.10k1/10W 5%RMC1/10T 103JJ242051031-18Bc2
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
33
Page 34
PA Unit
REF.
R 1523 CHIP RES.10k1/10W 5%RMC1/10T 103JJ24205103 VERSION C 19-Bc2
R 1523 CHIP RES.10k1/10W 5%RMC1/10T 103JJ24205103 VERSION A 19-Bc2
R 1523 CHIP RES.6.8k1/10W 5%RMC1/10T 682JJ24205682 VERSION A 23-Bc2
R 1524 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-18Bc2
R 1524 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ24185472 VERSION A 38-Bc2
R 1524 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ24185472 VERSION C 19-Bc2
R 1524 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ24185472 VERSION A
R 1525 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-Bg3
R 1526 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bg2
R 1527 CHIP RES.10k1/10W 5%RMC1/10T 103JJ242051031-18Bb2
R 1527 CHIP RES.10k1/10W 5%RMC1/10T 103JJ24205103 VERSION C 19-Bb2
R 1527 CHIP RES.10k1/10W 5%RMC1/10T 103JJ24205103 VERSION A 19-Bb2
R 1527 CHIP RES.6.8k1/10W 5%RMC1/10T 682JJ24205682 VERSION A 23-Bb2
R 1528 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-18Bb2
R 1528 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ24185472 VERSION A 38-Bb2
R 1528 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ24185472 VERSION C 19-Bb2
R 1528 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ24185472 VERSION A
R 1529 CHIP RES.47k1/10W 5%RMC1/10T 473JJ242054731-Ba3
R 1530 CHIP RES.47k1/10W 5%RMC1/10T 473JJ242054731-Ba3
R 1533 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021TH1501 THERMISTORNT732ATD2.0K KG90900791-AD3
C 2001 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 2001 CHIP CAP.0.033uF16VBECJ1VB1C333KK221295157-AB2
C 2001 CHIP CAP.0.1uF16VBGRM39B104K16PTK2212480523-AB2
C 2002 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Ba2
C 2003 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AB2
C 2004 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AB2
C 2005 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AB2
C 2006 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb2
C 2007 CHIP CAP.33pF50VCHGRM39CH330J50PTK221742231-AB2
C 2008 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 2009 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-AB2
C 2010 CHIP TA.CAP.1.5uF16VTESVA1C155M1-8RK781200201-Bb1
C 2011 CHIP CAP.33pF50VCHGRM39CH330J50PTK221742231-AB2
C 2012 CHIP CAP.5pF50VUJGRM39UJ050C50PTK221743051-AB2
C 2013 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bb1
C 2014 CHIP TA.CAP.0.1uF35VTESVA1V104M1-8RK781600251-Bb2
C 2015 CHIP CAP.82pF50VUJGRM39UJ820J50PTK221743301-AC2
C 2016 CHIP CAP.12pF50VUJGRM39UJ120J50PTK221743021-AC2
C 2017 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AC2
C 2018 CHIP CAP.47pF50VCHGRM39CH470J50PTK221742271-Bb1
C 2019 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AC2
C 2020 CHIP CAP.1uF10VFGRM39F105Z10PTK221050011-Ba2
C 2021 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Ba2
C 2022 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba2
C 2023 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Ba2
C 2024 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 2025 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-AB2
C 2026 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-AB2
C 2027 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Ba1
C 2028 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Ba1
C 2029 CHIP CAP.1pF50VCKGRM39CK010C50PTK221742021-AB2
C 2030 CHIP CAP.2pF50VCKGRM39CK020C50PTK221742031-AB2
C 2031 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AB1
C 2032 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Ba2
C 2033 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-18AB2
C 2033 CHIP CAP.0.001uF50VBGRM39B102K50PTK22174821 VERSION A 38-AB2
C 2033 CHIP CAP.0.001uF50VBGRM39B102K50PTK22174821 VERSION C 19-AB2
C 2033 CHIP CAP.0.001uF50VBGRM39B102K50PTK22174821 VERSION A
C 2034 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 2035 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 2036 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-AB2
C 2037 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-Bb2
C 2038 CHIP CAP.18pF50VCHGRM39CH180J50PTK221742171-AB2
C 2039 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-Bb2
C 2040 CHIP CAP.22pF50VCHGRM39CH220J50PTK221742191-AB2
C 2041 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Ba1
C 2042 CHIP CAP.120pF50VCHGRM39CH121J50PTK221742371-AB2
C 2043 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Ba1
C 2044 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB3
C 2045 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-AB3
C 2046 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Ba1
C 2047 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-AA2
C 2048 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-Bb2
C 2049 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-AA1
C 2050 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-AA3
C 2051 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-Bb3
C 2052 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb1
C 2053 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-Bb1
C 2054 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb1
DESCRIPTION
PCB with ComponentsCB0740001 VERSION C
Printed Circuit BoardFR003520D1-
VALUEV/WTOLVXSTD P/NMFR’S DESIGVERS
CB0740002 VERSION A
FR003520E6-
SIDE LAY ADR
LOT
19-37
AB2
39
Page 40
TX Unit
REF.
C 2055 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-AA3
C 2056 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb1
C 2057 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb1
C 2058 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb1
C 2059 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-AA2
C 2060 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AC2
C 2061 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AA1
C 2062 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AA1
C 2063 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Ba2
C 2064 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba1
C 2065 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 2066 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB3
C 2067 CHIP CAP.1pF50VCKGRM39CK010C50PTK221742021-AB1
C 2068 CHIP CAP.2pF50VCKGRM39CK020C50PTK221742031-AB1
C 2069 CHIP CAP.0.0068uF50VBGRM39B682M50PTK221748191-AB1
C 2070 TANTALUM CAP.3.3uF10VTPDN1A3R3M8S(MX0)K761000031-Ba2
C 2070 CHIP TA.CAP.3.3uF10VTEMSVA1A335M-8RK781000153-Ba2
C 2071 CHIP CAP.0.0082uF25VBGRM39B822M25PTK221448011-Bb1
D 2001 DIODERD6.8UMB2-T1BG20704381-Ba2
D 2002 DIODEHVU350TRFG20703801-AB2
D 2003 DIODEHVU350TRFG20703801-AC2
D 2004 DIODE1T363-01-T8AG20701141-AA1
D 2005 DIODE1T363-01-T8AG20701141-AA1
D 2006 DIODEHVU350TRFG20703801-AB1
D 2007 DIODERN739F T106G20706261-AA2
D 2008 DIODERN739F T106G20706261-AA2
D 2009 DIODEMA143-(TX)G20705361-Ba2
D 2010 DIODEMA143-(TX)G20705361-Ba2
J 2001 CONNECTORTMP-J01X-A2P10902551-AA2
JP2001 WIRE ASSYA1367+T92067921-AB1
L 2001 CHIP COIL0.22uHC2520C-R22JL16905481AA1
L 2001 CHIP COIL0.39uHC2520C-R39JL16905512-AA1
L 2002 COILE2 0.3-1.7-7T-RL00223721-6AA2
L 2002 COILE2 0.3-1.7-8T-LL0022376VERSION A 7-AA2
L 2002 COILE2 0.3-1.7-7T-RL0022372VERSION C 7-AA2
L 2003 M.RFC0.22uHLK2125 R22K-TL16903111-AA2
L 2004 CHIP COIL0.22uHC2520C-R22JL16905481-AB2
L 2005 CHIP COIL0.047uHC2520C-47NKL16905401-AB2
L 2006 CHIP COIL0.22uHC2520C-R22JL16905481-AB3
Q 2001 ICMB15A02PFV1-G-BND-EF G10925411-AB2
Q 2002 TRANSISTOR2SC4116GR TE85RG3341167G1-AB2
Q 2003 TRANSISTOR2SA1586Y TE85RG3115867Y1-AC2
Q 2004 TRANSISTORUN5215-(TX)G30701931-AC2
Q 2005 FET2SK508-T2B K52G3805087B1-AB2
Q 2006 TRANSISTOR2SC4116GR TE85RG3341167G1-Ba1
Q 2007 TRANSISTOR2SA1586Y TE85RG3115867Y1-Ba1
Q 2008 TRANSISTOR2SC5226-4/5-TLG3352268Z1-AB2
Q 2009 TRANSISTOR2SC4116GR TE85RG3341167G1-Bb2
Q 2010 TRANSISTOR2SC3357-T2 RFG3333577F1-AB3
Q 2011 TRANSISTORXN1213-(TX)G30701941-Bb3
Q 2012 ICTA78L05F TE12RG10910141-AA1
Q 2013 TRANSISTOR2SA1179M6-TAG3111797F1-Bc1
Q 2014 TRANSISTORUN5213-(TX)G30701921-Bb1
Q 2015 TRANSISTORXN1213-(TX)G30701941-Bb2
Q 2016 TRANSISTORUN5213-(TX)G30701921-Bc1
Q 2017 TRANSISTOR2SA1179M6-TAG3111797F1-Bc1
R 2001 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Ba2
R 2002 CHIP RES.5601/16W 5%RMC1/16 561JATPJ241855611-Ba2
R 2003 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AC2
R 2004 CHIP RES.1.8k1/16W 5%RMC1/16 182JATPJ241851821-Ba2
R 2005 CHIP RES.1.8k1/16W 5%RMC1/16 182JATPJ241851821-Bb1
R 2006 CHIP RES.471/16W 5%RMC1/16 470JATPJ241854701-AB2
R 2007 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-Bb1
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
40
Page 41
TX Unit
REF.
R 2008 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-AB2
R 2009 CHIP RES.22k1/16W 5%RMC1/16 223JATPJ241852231-AC2
R 2010 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AC2
R 2011 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AC2
R 2012 CHIP RES.100k1/16W 5%RMC1/16 104JATPJ241851041-AB2
R 2013 CHIP RES.100k1/16W 5%RMC1/16 104JATPJ241851041-Bb1
R 2014 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-Ba2
R 2015 CHIP RES.221/16W 5%RMC1/16 220JATPJ241852201-AB1
R 2016 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-AC2
R 2017 CHIP RES.100k1/16W 1%RMC1/16 104FTPJ241831041-Ba2
R 2017 CHIP RES.220k1/16W 1%RMC1/16 224FTPJ241832247-Ba2
R 2018 CHIP RES.100k1/16W 1%RMC1/16 104FTPJ241831041-Ba2
R 2018 CHIP RES.220k1/16W 1%RMC1/16 224FTPJ241832247-Ba2
R 2019 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AC2
R 2020 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Ba2
R 2021 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-AC2
R 2022 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850001-Ba2
R 2023 CHIP RES.6801/16W 1%RMC1/16 681FTPJ241836811-Ba2
R 2024 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-AB2
R 2025 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AA2
R 2026 CHIP RES.47k1/16W 1%RMC1/16 473FTPJ241834731-AC1
R 2026 CHIP RES.27k1/16W 1%RMC1/16 273FTPJ241832736-AC1
R 2027 CHIP RES.12k1/16W 1%RMC1/16 123FTPJ241831231-AC1
R 2027 CHIP RES.27k1/16W 1%RMC1/16 273FTPJ241832736-AC1
R 2028 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AB2
R 2029 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-AB2
R 2030 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AB1
R 2031 CHIP RES.3.3k1/16W 5%RMC1/16 332JATPJ241853321-AB2
R 2032 CHIP RES.2.2k1/16W 5%RMC1/16 222JATPJ241852221-AA2
R 2033 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-AB2
R 2034 CHIP RES.2201/16W 5%RMC1/16 221JATPJ241852211-AB2
R 2035 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-AB2
R 2036 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-Ba2
R 2037 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-Bb2
R 2038 CHIP RES.2.2k1/16W 5%RMC1/16 222JATPJ241852221-Bb2
R 2039 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-AB3
R 2040 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-AB2
R 2041 CHIP RES.1001/10W 5%RMC1/10T 101JJ242051011-AB3
R 2042 CHIP RES.4701/16W 5%RMC1/16 471JATPJ241854711-AB3
R 2043 CHIP RES.1501/16W 5%RMC1/16 151JATPJ241851511-AB2
R 2044 CHIP RES.3301/16W 5%RMC1/16 331JATPJ241853311-AB2
R 2045 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-AB2
R 2046 CHIP RES.3301/16W 5%RMC1/16 331JATPJ241853311-AB2
R 2047 CHIP RES.8201/16W 5%RMC1/16 821JATPJ241858211-AA2
R 2048 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-AB3
R 2049 CHIP RES.8201/16W 5%RMC1/16 821JATPJ241858211-AA3
R 2050 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bc1
R 2051 CHIP RES.8201/16W 5%RMC1/16 821JATPJ241858211-AA3
R 2052 CHIP RES.6801/16W 5%RMC1/16 681JATPJ241856811-6AB1
R 2052 CHIP RES.1.2k1/16W 5%RMC1/16 122JATPJ24185122 VERSION A 7-AB1
R 2052 CHIP RES.6801/16W 5%RMC1/16 681JATPJ24185681 VERSION C 7-AB1
R 2053 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-AB1
R 2056 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850001-Bb1
R 2058 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-Bb1
R 2059 CHIP RES.3301/16W 5%RMC1/16 331JATPJ241853311-Bb2
R 2060 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-Bc2
R 2061 CHIP RES.3301/16W 5%RMC1/16 331JATPJ241853311-Bc2
R 2062 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bb1
R 2063 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850001-Ba2
R 2064 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850001-Ba2
R 2065 CHIP RES.10k1/16W 1%RMC1/16 103FTPJ241831031-AC1
R 2065 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850006-AC1
R 2066 CHIP RES.100k1/16W 1%RMC1/16 104FTPJ241831041-AC1
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
41
Page 42
TX Unit
REF.
R 2066 CHIP RES.56k1/16W 1%RMC1/16 563FTPJ241835636-AC1
R 2067 CHIP RES.82k1/16W 1%RMC1/16 823FTPJ241838231-AC1
R 2067 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850006-AC1
R 2068 CHIP RES.56k1/16W 1%RMC1/16 563FTPJ241835631-AC1
R 2068 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850006-AC1
R 2069 CHIP RES.5.6k1/16W 1%RMC1/16 562FTPJ241835621-AB1
R 2069 CHIP RES.2.2k1/16W 1%RMC1/16 222FTPJ241832226-AB1
R 2070 CHIP RES.3.9k1/16W 1%RMC1/16 392FTPJ241833921-AB1
R 2070 CHIP RES.4.7k1/16W 1%RMC1/16 472FTPJ241834726-AB1
R 2071 CHIP RES.1.2k1/16W 1%RMC1/16 122FTPJ241831221-AB1
R 2071 CHIP RES.4.7k1/16W 1%RMC1/16 472FTPJ241834726-AB1
R 2072 CHIP RES.6.8k1/16W 1%RMC1/16 682FTPJ241836821-Ba2
R 2073 CHIP RES.56k1/16W 1%RMC1/16 563FTPJ241835631-5AC1
R 2074 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bb2
R 2075 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bc1
R 2076 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850006-Bb1
TC2001 TRIMMER CAP.10pFECR-JA010A11XK910002271-AB2
TH2001 THERMISTORNTCCM20123SH223JCTG90901061-AC1
TH2002 THERMISTORNTCCM20123NH153JCTG90901051-AB1
X 2001 XTAL TOP-B14.4MHz14.4MHZH01032211-AC2
C 3001 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba1
C 3002 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Be2
C 3003 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AA2
C 3003 CHIP CAP.0.033uF16VBECJ1VB1C333KK221295157-AA2
C 3003 CHIP CAP.0.1uF16VBGRM39B104K16PTK2212480523-AA2
C 3004 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AA2
C 3005 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AA2
C 3006 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AF2
C 3007 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AF1
C 3008 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AA2
C 3009 CHIP TA.CAP.1.5uF16VTESVA1C155M1-8RK781200201-Be2
C 3010 CHIP CAP.22pF50VCHGRM39CH220J50PTK221742191-AE1
C 3011 CHIP CAP.12pF50VCHGRM39CH120J50PTK221742131-AE1
C 3012 CHIP CAP.33pF50VCHGRM39CH330J50PTK221742231-AA1
C 3013 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AA1
C 3014 CHIP CAP.0.033uF16VRGRM39R333K16PTK221248011-Be2
C 3015 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-AA2
C 3016 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AE2
C 3017 CHIP CAP.56pF50VCHGRM39CH560J50PTK221742291-AA2
C 3018 CHIP CAP.4pF50VUJGRM39UJ040C50PTK221743041-AA2
C 3019 CHIP CAP.7pF50VCHGRM39CH070D50PTK221742081-6AE1
C 3019 CHIP CAP.9pF50VCHGRM39CH090C50PTK22174247 VERSION A 7AE1
C 3019 CHIP CAP.9pF50VCHGRM39CH090D50PTK22174210 VERSION A 8-AE1
C 3019 CHIP CAP.7pF50VCHGRM39CH070D50PTK22174208 VERSION C 7-AE1
C 3020 CHIP TA.CAP.0.1uF35VTESVA1V104M1-8RK781600251-Be2
C 3021 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-6AE1
C 3021 CHIP CAP.12pF50VCHGRM39CH120J50PTK22174213 VERSION A 7-AE1
C 3021 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION C 7-AE1
C 3022 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bb2
C 3023 CHIP CAP.2pF50VCKGRM39CK020C50PTK221742031-AA2
C 3024 CHIP CAP.33pF50VCHGRM39CH330J50PTK221742231-6AE1
C 3024 CHIP CAP.39pF50VCHGRM39CH390J50PTK22174225 VERSION A 7-AE1
C 3024 CHIP CAP.33pF50VCHGRM39CH330J50PTK22174223 VERSION C 7-AE1
C 3025 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AA1
C 3026 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AA2
C 3027 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-6AE1
C 3027 CHIP CAP.12pF50VCHGRM39CH120J50PTK22174213 VERSION A 7-AE1
C 3027 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION C 7-AE1
C 3028 CHIP CAP.8pF50VCHGRM39CH080C50PTK221742461-6AE1
C 3028 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION A 7-AE1
C 3028 CHIP CAP.8pF50VCHGRM39CH080C50PTK22174246 VERSION C 7-AE1
C 3029 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AA1
C 3030 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-6AE2
C 3030 CHIP CAP.12pF50VCHGRM39CH120J50PTK22174213 VERSION A 7-AE2
C 3030 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION C 7-AE2
C 3031 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AE2
C 3032 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf2
C 3033 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-6AE1
C 3033 CHIP CAP.22pF50VCHGRM39CH220J50PTK22174219 VERSION A 7-AE1
C 3033 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION C 7-AE1
C 3034 CHIP CAP.4pF50VCHGRM39CH040C50PTK22174205 VERSION A 7-AC3
C 3035 CHIP CAP.47pF50VCHGRM39CH470J50PTK221742271-AB3
C 3036 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AE1
C 3037 CHIP CAP.8pF50VCHGRM39CH080D50PTK221742091-AC2
C 3038 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Bf2
C 3039 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 3040 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-AE1
C 3041 CHIP CAP.18pF50VCHGRM39CH180J50PTK221742171-AB2
C 3042 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf2
DESCRIPTION
PCB with ComponentsCS1646001 VERSION C
Printed Circuit BoardFR003530D1-
VALUEV/WTOLVXSTD P/NMFR’S DESIGVERS
CS1646002 VERSION A
FR003530E6-
SIDE LAY ADR
LOT
49
Page 50
RX Unit
REF.
C 3043 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf2
C 3044 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf2
C 3045 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-AC2
C 3046 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD2
C 3047 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD1
C 3047 CHIP CAP.0.01uF25VBGRM39B103M25PTK2214480211-AD1
C 3048 CHIP CAP.2pF50VCKGRM39CK020C50PTK221742031-AB2
C 3049 CHIP CAP.9pF50VCHGRM39CH090D50PTK221742101-6AD1
C 3049 CHIP CAP.22pF50VCHGRM39CH220J50PTK22174219 VERSION A 7-AD1
C 3049 CHIP CAP.9pF50VCHGRM39CH090D50PTK22174210 VERSION C 7-AD1
C 3050 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-6AD1
C 3050 CHIP CAP.12pF50VCHGRM39CH120J50PTK22174213 VERSION A 7-AD1
C 3050 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION C 7-AD1
C 3051 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD2
C 3052 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 3053 CHIP CAP.8pF50VCHGRM39CH080D50PTK221742091-6AD1
C 3053 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION A 7-AD1
C 3053 CHIP CAP.8pF50VCHGRM39CH080D50PTK22174209 VERSION C 7-AD1
C 3054 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-6AD1
C 3054 CHIP CAP.12pF50VCHGRM39CH120J50PTK22174213 VERSION A 7-AD1
C 3054 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION C 7-AD1
C 3055 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 3056 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 3057 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB2
C 3058 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bc2
C 3059 CHIP CAP.22pF50VCHGRM39CH220J50PTK221742191-6AD1
C 3059 CHIP CAP.39pF50VCHGRM39CH390J50PTK22174225 VERSION A 7-AD1
C 3059 CHIP CAP.22pF50VCHGRM39CH220J50PTK22174219 VERSION C 7-AD1
C 3060 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-6AD1
C 3060 CHIP CAP.12pF50VCHGRM39CH120J50PTK22174213 VERSION A 7-AD1
C 3060 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION C 7-AD1
C 3061 CHIP CAP.15pF50VCHGRM39CH150J50PTK221742151-AB2
C 3062 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-Be2
C 3063 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD2
C 3064 CHIP CAP.18pF50VCHGRM39CH180J50PTK221742171-AB2
C 3065 CHIP CAP.8pF50VCHGRM39CH080C50PTK221742461-6AD1
C 3065 CHIP CAP.10pF50VCHGRM39CH100D50PTK22174211 VERSION A 7-AD1
C 3065 CHIP CAP.8pF50VCHGRM39CH080C50PTK22174246 VERSION C 7-AD1
C 3066 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-Be2
C 3067 CHIP CAP.9pF50VCHGRM39CH090D50PTK221742101-6AD2
C 3067 CHIP CAP.12pF50VCHGRM39CH120J50PTK22174213 VERSION A 7-AD2
C 3067 CHIP CAP.9pF50VCHGRM39CH090D50PTK22174210 VERSION C 7-AD2
C 3068 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be3
C 3069 CHIP CAP.15pF50VCHGRM39CH150J50PTK221742151-6AC1
C 3069 CHIP CAP.22pF50VCHGRM39CH220J50PTK22174219 VERSION A 7-AC1
C 3069 CHIP CAP.15pF50VCHGRM39CH150J50PTK22174215 VERSION C 7-AC1
C 3070 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be3
C 3071 CHIP CAP.27pF50VCHGRM39CH270J50PTK221742211-AC2
C 3072 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB1
C 3073 CHIP CAP.12pF50VCHGRM39CH120J50PTK221742131-AC1
C 3074 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be3
C 3075 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-AB1
C 3076 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be3
C 3077 CHIP CAP.47pF50VCHGRM39CH470J50PTK221742271-AC1
C 3078 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bf3
C 3079 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB1
C 3080 CHIP CAP.15pF50VCHGRM39CH150J50PTK221742151-AB1
C 3081 CHIP CAP.5pF50VCHGRM39CH050C50PTK221742061-AB1
C 3083 CHIP CAP.0.01uF50VBGRM39B103M50PTK221748231-Bc2
C 3084 CHIP CAP.0.01uF50VBGRM39B103M50PTK221748231-Bc2
C 3086 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bb3
C 3087 CHIP CAP.22pF50VCHGRM39CH220J50PTK221742191-AE3
C 3088 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD3
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
50
Page 51
RX Unit
REF.
C 3089 CHIP CAP.56pF50VCHGRM39CH560J50PTK221742291-AE3
C 3091 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bb3
C 3092 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Ba3
C 3094 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Bd3
C 3095 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb3
C 3096 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AE3
C 3097 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bd2
C 3098 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Bd2
C 3099 CHIP CAP.82pF50VCHGRM39CH820J50PTK221742331-AD3
C 3100 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AE3
C 3101 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AC3
C 3102 CHIP CAP.180pF50VCHGRM39CH181J50PTK221742411-Bb2
C 3103 CHIP CAP.180pF50VCHGRM39CH181J50PTK221742411-Bb2
C 3104 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bc3
C 3105 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba3
C 3106 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba2
C 3107 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be3
C 3108 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AE2
C 3109 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-Bc3
C 3110 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Bb3
C 3111 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb3
C 3112 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bb3
C 3113 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be3
C 3114 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bb2
C 3115 CHIP CAP.0.0047uF50VBGRM39B472M50PTK221748171-Bc2
C 3116 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bd3
C 3117 CHIP CAP.12pF50VCHGRM39CH120J50PTK221742131-Bc3
C 3118 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be3
C 3119 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AE2
C 3120 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be3
C 3121 CHIP CAP.39pF50VCHGRM39CH390J50PTK221742251-AD3
C 3122 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be3
C 3123 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD3
C 3125 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD3
C 3126 CHIP CAP.0.01uF25VBGRM39B103M25PTK221448021-AD3
C 3127 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-AC3
C 3128 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AE2
C 3129 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AE2
C 3130 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AC3
C 3131 CHIP CAP.0.047uF16VBGRM39B473K16PTK221248041-AE2
C 3132 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AC3
C 3133 CHIP TA.CAP.10uF16VTEMSVB21C106M-8RK781200251-Bd3
C 3134 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AB1
C 3136 CHIP CAP.1pF50VCKGRM39CK010C50PTK221742021-AA2
C 3137 CHIP CAP.18pF50VUJGRM39UJ180J50PTK221743141-AA2
C 3138 TANTALUM CAP.10uF10VTPDN1A100M8S(MX0)K761000061-Bc3
C 3138 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000283-Bc3
CD3001 CERAMIC DISCCDB455C7H79001801-AD2
CF3001 CERAMIC FILTERCFWM455GH39003991-AE3
CF3002 CERAMIC FILTERCFWM455FH39003951-AF3
D 3001 DIODEMA143-(TX)G20705361-Ba1
D 3002 DIODERD6.8UMB2-T1BG20704381-Bf2
D 3003 DIODERN739F T106G20706261-AF1
D 3004 DIODEHVU350TRFG20703801-AE1
D 3005 DIODEHVU350TRFG20703801-AB3
D 3006 DIODEHVU350TRFG20703801-AB3
D 3007 DIODEHVU350TRFG20703801-AA2
D 3008 DIODEHVU350TRFG20703801-AE1
D 3009 DIODEHVU350TRFG20703801-AB3
D 3010 DIODEHVU350TRFG20703801-AB3
D 3011 DIODEMA143-(TX)G20705361-AE1
D 3012 DIODEHVU350TRFG20703801-AD1
D 3013 DIODEHVU350TRFG20703801-AD1
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
51
Page 52
RX Unit
REF.
D 3014 ICGN2011-Q(TX)G10921831-AC2
D 3015 DIODEMA142WK-(TX)G20705341-Bb3
D 3016 DIODEMA142WK-(TX)G20705341-Bb3
D 3017 DIODERD5.6EB3G20901931-Bc2
D 3017 DIODEHZM5.6NB2 TRG20707226-Bc2
D 3018 DIODEMA143-(TX)G20705361-AE2
D 3019 DIODEMA143-(TX)G20705361-AE2
D 3021 DIODEMA143-(TX)G20705361-Bf2
J 3001 CONNECTORTMP-J01X-V6P10902101-AC1
JP3001 WIRE ASSYA1367+T92067911-AA3
JP3002 WIRE ASSYA1367+T92067881JP3051 WIRE ASSYGRN 55 2/2T505055003JP3052 WIRE ASSYGRN 35 2/2T5050350011L 3001 M.RFC10uHLK1608 100K-TL16906891-AF2
L 3002 CHIP COIL0.1uHC2520C-R10JL16905441-6AE1
L 3002 CHIP COIL0.12uHC2520C-R12JL1690545VERSION A 7-AE1
L 3002 CHIP COIL0.1uHC2520C-R10JL1690544VERSION C 7-AE1
L 3003 CHIP COIL0.68uHC2520C-R68JL16905541-AB3
L 3004 CHIP COIL0.1uHC2520C-R10JL16905441-6AE1
L 3004 CHIP COIL0.12uHC2520C-R12JL1690545VERSION A 7-AE1
L 3004 CHIP COIL0.1uHC2520C-R10JL1690544VERSION C 7-AE1
L 3005 COILE2 0.3-1.7-8T-LL00223761-6AC3
L 3005 COILE2 0.25-1.9-8T-LL0022550VERSION A 7-AC3
L 3005 COILE2 0.3-1.7-8T-LL0022376VERSION C 7-AC3
L 3006 CHIP COIL0.22uHC2520C-R22JL16905481-AB2
L 3007 CHIP COIL0.82uHC2520C-R82JL16905551-AD1
L 3008 M.RFC0.22uHLK2125 R22K-TL16903111-AC2
L 3009 CHIP COIL0.1uHC2520C-R10JL16905441-6AD1
L 3009 CHIP COIL0.12uHC2520C-R12JL1690545VERSION A 7-AD1
L 3009 CHIP COIL0.1uHC2520C-R10JL1690544VERSION C 7-AD1
L 3010 CHIP COIL0.22uHC2520C-R22JL16905481-AB2
L 3011CHIP COIL0.047uHC2520C-47NKL16905401-AB2
L 3012 CHIP COIL0.1uHC2520C-R10JL16905441-6AD1
L 3012 CHIP COIL0.12uHC2520C-R12JL1690545VERSION A 7-AD1
L 3012 CHIP COIL0.1uHC2520C-R10JL1690544VERSION C 7-AD1
L 3013 M.RFC0.082uHLK2125 82NM-TL16906041-AC1
L 3015 M.RFC0.082uHLK2125 82NM-TL16906041-AC1
L 3016 CHIP COIL0.22uHC2520C-R22JL16905481-AB1
L 3017 M.RFC10uHLK2125 100K-TL16903311-Bd2
L 3018 CHIP COIL1uHC2520F-1R0KL16905841-AD3
L 3019 M.RFC0.047uHHK1608 47NJ-TL16905241-AD2
Q 3001 ICMB15A02PFV1-G-BND-EF G10925411-AA2
Q 3002 TRANSISTOR2SC4116GR TE85RG3341167G1-AA2
Q 3003 TRANSISTOR2SA1586Y TE85RG3115867Y1-AA1
Q 3004 TRANSISTORUN5215-(TX)G30701931-AA1
Q 3005 TRANSISTOR2SC4116GR TE85RG3341167G1-Bf2
Q 3006 TRANSISTOR2SA1586Y TE85RG3115867Y1-Bf2
Q 3007 FET2SK508-T2B K52G3805087B1-AC2
Q 3008 TRANSISTOR2SC3357-T2 RFG3333577F1-AD1
Q 3009 TRANSISTOR2SC5226-4/5-TLG3352268Z1-AB2
Q 3010 TRANSISTOR2SC4116GR TE85RG3341167G1-Be2
Q 3011 TRANSISTOR2SC3357-T2 RFG3333577F1-AB1
Q 3012 ICTA31136FN(EL)G10916051-AE3
Q 3013 TRANSISTOR2SC2812L6-TAG3328127F1-Bc3
Q 3013 TRANSISTOR2SC2812NL6-TBG3328128F18-Bc3
Q 3014 TRANSISTOR2SC4116GR TE85RG3341167G1-AE2
Q 3015 TRANSISTORXN1213-(TX)G30701941-Ba3
Q 3016 TRANSISTOR2SC2620QBTRG3326207B1-AD3
Q 3018 TRANSISTOR2SB1122S-TDG3211228S1-Bc2
Q 3020 TRANSISTORXN1213-(TX)G30701941-Bb3
Q 3021 ICTA78L05F TE12RG10910141-AC3
Q 3022 TRANSISTORXN1213-(TX)G30701941-Bb2
R 3001 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Ba1
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
52
Page 53
RX Unit
REF.
R 3002 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bf1
R 3003 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-Ba2
R 3004 CHIP RES.5601/16W 5%RMC1/16 561JATPJ241855611-Be1
R 3005 CHIP RES.1.8k1/16W 5%RMC1/16 182JATPJ241851821-Be2
R 3006 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AA2
R 3007 CHIP RES.1.8k1/16W 5%RMC1/16 182JATPJ241851821-Be2
R 3008 CHIP RES.6.8k1/16W 5%RMC1/16 682JATPJ241856821-Be2
R 3009 CHIP RES.471/16W 5%RMC1/16 470JATPJ241854701-AA2
R 3010 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AE2
R 3011 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-AA1
R 3012 CHIP RES.22k1/16W 5%RMC1/16 223JATPJ241852231-AA2
R 3013 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AA2
R 3014 CHIP RES.331/16W 5%RMC1/16 330JATPJ241853301-AB3
R 3015 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AA2
R 3016 CHIP RES.100k1/16W 5%RMC1/16 104JATPJ241851041-AA1
R 3017 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AE2
R 3018 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-AA1
R 3019 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AA2
R 3020 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-AA1
R 3023 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-AB2
R 3024 CHIP RES.3.3k1/16W 5%RMC1/16 332JATPJ241853321-AD2
R 3025 CHIP RES.2.2k1/16W 5%RMC1/16 222JATPJ241852221-AE1
R 3026 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AD1
R 3027 CHIP RES.2201/16W 5%RMC1/16 221JATPJ241852211-AD1
R 3028 CHIP RES.101/16W 5%RMC1/16 100JATPJ241851001-AD2
R 3028 CHIP RES.1001/16W 5%RMC1/16 101JATPJ2418510111-AD2
R 3029 CHIP RES.47k1/16W 1%RMC1/16 473FTPJ241834731-AA3
R 3030 CHIP RES.12k1/16W 1%RMC1/16 123FTPJ241831231-AA2
R 3031 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AC2
R 3032 CHIP RES.3.3k1/16W 5%RMC1/16 332JATPJ241853321-AB2
R 3033 CHIP RES.2.2k1/16W 5%RMC1/16 222JATPJ241852221-AB2
R 3034 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AD2
R 3035 CHIP RES.2201/16W 5%RMC1/16 221JATPJ241852211-AB2
R 3036 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-AB2
R 3037 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AD2
R 3038 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-AB2
R 3039 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-Be1
R 3040 CHIP RES.2.2k1/16W 5%RMC1/16 222JATPJ241852221-Be2
R 3042 CHIP RES.181/16W 5%RMC1/16 180JATPJ241851801-Be1
R 3043 CHIP RES.561/16W 5%RMC1/16 560JATPJ241855601-Bd2
R 3044 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-AB1
R 3045 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-AB1
R 3046 CHIP RES.1501/16W 5%RMC1/16 151JATPJ241851511-AB1
R 3046 CHIP RES.1001/16W 5%RMC1/16 101JATPJ2418510111-AB1
R 3047 CHIP RES.1001/10W 5%RMC1/10T 101JJ242051011-AB1
R 3048 CHIP RES.4701/16W 5%RMC1/16 471JATPJ241854711-AB1
R 3049 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-Bc2
R 3049 CHIP RES.1001/16W 1%RMC1/16 101FTPJ241831016-Bc2
R 3050 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-Bc2
R 3050 CHIP RES.1001/16W 1%RMC1/16 101FTPJ241831016-Bc2
R 3051 CHIP RES.22k1/16W 5%RMC1/16 223JATPJ241852231-Bb3
R 3052 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AE3
R 3054 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-Ba3
R 3055 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-Ba3
R 3056 CHIP RES.1.2k1/16W 5%RMC1/16 122JATPJ241851221-AD3
R 3057 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-Bb3
R 3058 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-Bb3
R 3059 CHIP RES.150k1/16W 5%RMC1/16 154JATPJ241851541-Bb3
R 3061 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850001-AC3
R 3063 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Ba2
R 3064 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-Bd3
R 3065 CHIP RES.1.8k1/16W 5%RMC1/16 182JATPJ241851821-Bb2
R 3066 CHIP RES.22k1/16W 5%RMC1/16 223JATPJ241852231-Bb3
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
53
Page 54
RX Unit
REF.
R 3067 CHIP RES.6.8k1/16W 5%RMC1/16 682JATPJ241856821-Bb3
R 3068 CHIP RES.1.8k1/16W 5%RMC1/16 182JATPJ241851821-Bb2
R 3069 CHIP RES.3301/10W 5%RMC1/10T 331JJ242053311-Bc3
R 3070 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Ba2
R 3071 CHIP RES.471/16W 5%RMC1/16 470JATPJ241854701-AE2
R 3072 CHIP RES.220k1/16W 5%RMC1/16 224JATPJ241852241-AE2
R 3074 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AD3
R 3075 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AE2
R 3076 CHIP RES.1001/16W 5%RMC1/16 101JATPJ241851011-AE2
R 3077 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AD3
R 3078 CHIP RES.47k1/16W 5%RMC1/16 473JATPJ241854731-AD3
R 3080 CHIP RES.6.8k1/16W 5%RMC1/16 682JATPJ241856821-Bb3
R 3082 CHIP RES.2201/16W 5%RMC1/16 221JATPJ241852211-AD3
R 3083 CHIP RES.12k1/16W 5%RMC1/16 123JATPJ241851231-AE2
R 3084 CHIP RES.18k1/16W 5%RMC1/16 183JATPJ241851831-AE2
R 3086 CHIP RES.1k1/16W 5%RMC1/16 102JATPJ241851021-AD2
R 3088 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bb2
R 3089 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bb2
R 3090 CHIP RES.33k1/16W 5%RMC1/16 333JATPJ241853331-AE2
R 3092 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bc3
R 3093 CHIP RES.10k1/16W 5%RMC1/16 103JATPJ241851031-Bb2
R 3096 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-Bc3
R 3099 CHIP RES.18k1/16W 1%RMC1/16 183FTPJ241831831-AA2
R 3100 CHIP RES.100k1/16W 1%RMC1/16 104FTPJ241831041-AA3
R 3101 CHIP RES.8.2k1/16W 1%RMC1/16 822FTPJ241838221-AA3
R 3102 CHIP RES.47k1/16W 1%RMC1/16 473FTPJ241834731-AA3
R 3103 CHIP RES.3.9k1/16W 1%RMC1/16 392FTPJ241833921-AA2
R 3106 CHIP RES.4.7k1/16W 5%RMC1/16 472JATPJ241854721-Ba2
R 3107 CHIP RES.56k1/16W 1%RMC1/16 563FTPJ241835631-AA3
R 3108 CHIP RES.6.8k1/16W 1%RMC1/16 682FTPJ241836821-Bf2
R 3109 CHIP RES.4.7k1/16W 1%RMC1/16 472FTPJ241834721-Bf2
R 3110 CHIP RES.2.7k1/16W 1%RMC1/16 272FTPJ241832721-Bf2
R 3111 CHIP RES.1k1/16W 1%RMC1/16 102FTPJ241831021-AA2
R 3112 CHIP RES.1.8k1/16W 1%RMC1/16 182FTPJ241831821-AA3
R 3113 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850001-Bf2
R 3114 CHIP RES.01/16W 5%RMC1/16 000JATPJ241850001-Bf2
T 3001 COIL WIDE-TRANS.960812088L00224781-AC2
T 3002 COIL WIDE-TRANS.950812004L00224791-AC2
T 3003 COIL WIDE-TRANS.960812088L00224781-AC2
TC3001 TRIMMER CAP.10pFECR-JA010A11XK910002271-AA2
TH3001 THERMISTORNTCCM20123SH223JCTG90901061-AA3
TH3002 THERMISTORNTCCM20123NH153JCTG90901051-AA3
X 3001 XTAL TOP-B14.4MHz14.4MHZH01032211-AA2
X 3002 XTAL LP-5.0S.2S20.945MHz20.945MHZH01031691-AD3
XF3001 XTAL FILTER21M10B1H11023141-AC3
XF3002 XTAL FILTER21M10B1H11023141-AC3
C 4001 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg2
C 4002 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg2
C 4003 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg2
C 4004 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh1
C 4005 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh1
C 4006 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh1
C 4007 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bh3
C 4008 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh1
C 4009 AL.ELECTRO.CAP.100uF25VRE2-25V101M 100UFK401490281-AA5
C 4010 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh3
C 4011 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh1
C 4012 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bh4
C 4013 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg3
C 4014 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh2
C 4015 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg3
C 4016 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh2
C 4017 AL.ELECTRO.CAP.10uF25VRC2-25V100M(5X7)K401490121-AA3
C 4018 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh2
C 4019 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bi3
C 4020 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh2
C 4021 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh2
C 4022 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bi4
C 4023 AL.ELECTRO.CAP.100uF16VECEV1CA101WPK481200121-AA4
C 4024 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bh3
C 4025 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg2
C 4026 CHIP CAP.1uF10VFGRM39F105Z10PTK221050011-Bg1
C 4027 AL.ELECTRO.CAP.10uF16VECEV1CS100SRK481200011-AA3
C 4028 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bg1
C 4029 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg1
C 4030 CHIP CAP.1uF10VFGRM39F105Z10PTK221050011-AB2
C 4031 AL.ELECTRO.CAP.470uF16VRE3-16V471M 470UFK401290661-AB3
C 4032 CHIP CAP.56pF50VCHGRM39CH560J50PTK221742291-Bf1
C 4033 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg3
C 4034 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bg2
C 4035 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bh2
C 4036 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bg4
C 4037 CHIP TA.CAP.2.2uF25VTEMSVA1E225M-8RK781400201-Bh4
C 4038 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf1
C 4039 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bg2
C 4040 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bg2
C 4041 CHIP TA.CAP.33uF10VTEMSVB21A336M-8RK781000471-Bg1
C 4042 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bh4
C 4043 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bg2
C 4044 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bg2
C 4045 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bg2
C 4046 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bh4
C 4047 CHIP CAP.1uF10VFGRM39F105Z10PTK221050011-Bh2
C 4048 CHIP CAP.0.047uF16VBGRM39B473K16PTK221248041-Bg4
C 4049 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-AB2
C 4050 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bg2
C 4051 CHIP CAP.0.022uF25VBGRM39B223K25PTK221448071-Bf1
C 4052 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg6
C 4053 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg6
C 4054 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg6
C 4055 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bh6
C 4055 CHIP CAP.220pF50VCHGRM39CH221J50PTK2217424319-Bh6
C 4056 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bg2
C 4057 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bg3
C 4058 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bg2
DESCRIPTION
PCB with ComponentsCS1647001 VERSION C
Printed Circuit BoardFR003540C1-
VALUEV/WTOLVXSTD P/NMFR’S DESIGVERS
CS1647002 VERSION A
FR003540D6-
SIDE LAY ADR
LOT
61
Page 62
CNTL Unit
REF.
C 4059 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bf1
C 4060 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf2
C 4061 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg6
C 4062 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg6
C 4063 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bf1
C 4064 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bf1
C 4065 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd6
C 4066 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd6
C 4067 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd6
C 4068 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd6
C 4069 CHIP CAP.10pF50VCHGRM39CH100D50PTK221742111-Bg4
C 4070 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bf4
C 4071 CHIP CAP.3pF50VCJGRM39CJ030C50PTK221742041-Bg4
C 4072 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Bf4
C 4073 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bf1
C 4074 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4075 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4076 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4077 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4078 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4079 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4080 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4081 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Be1
C 4082 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bf4
C 4083 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bf2
C 4084 CHIP CAP.15pF50VCHGRM39CH150J50PTK221742151-Bf4
C 4085 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bf2
C 4086 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bf4
C 4087 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd6
C 4088 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd6
C 4088 CHIP CAP.220pF50VCHGRM39CH221J50PTK2217424319-Bd6
C 4089 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd6
C 4090 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Be1
C 4091 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Be3
C 4092 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf3
C 4093 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bf3
C 4094 CHIP CAP.0.022uF25VBGRM39B223K25PTK221448071-Be5
C 4095 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bd5
C 4096 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Be5
C 4097 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-AD2
C 4098 CHIP CAP.0.022uF25VBGRM39B223K25PTK221448071-Bc4
C 4099 CHIP CAP.0.0039uF50VBGRM39B392K50PTK221748306-Be2
C 4100 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Be4
C 4101 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bc5
C 4102 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AD2
C 4104 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Be4
C 4105 CHIP CAP.0.015uF25VBGRM39B153K25PTK221448056-Be2
C 4106 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be4
C 4107 CHIP CAP.1uF10VBGRM40B105K10PTK221008021-Bc4
C 4108 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be4
C 4110 CHIP CAP.0.0015uF50VBGRM39B152M50PTK221748111-Be1
C 4111 CHIP CAP.1uF10VBGRM40B105K10PTK221008021-Be4
C 4112 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bc6
C 4113 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bc6
C 4114 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bc6
C 4115 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg6
C 4116 CHIP CAP.0.015uF25VBGRM39B153K25PTK221448056-AE2
C 4117 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-Bd4
C 4118 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Be2
C 4119 CHIP CAP.0.0033uF50VBGRM39B332M50PTK221748151-AE1
C 4120 CHIP TA.CAP.0.1uF35VTESVA1V104M1-8RK781600251-AE2
C 4120 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248056-AE2
C 4121 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bc5
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
62
Page 63
CNTL Unit
REF.
C 4122 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bc6
C 4124 CHIP TA.CAP.1.5uF20VTEMSVA1D155M-8RK781300131-Be4
C 4125 CHIP CAP.0.0015uF50VBGRM39B152M50PTK221748111-Bd1
C 4126 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bg5
C 4127 CHIP CAP.1uF10VBGRM40B105K10PTK221008021-Be4
C 4129 CHIP CAP.470pF50VCHGRM39CH471J50PTK221742491-AC5
C 4130 CHIP TA.CAP.1.5uF20VTEMSVA1D155M-8RK781300131-AE3
C 4131 CHIP CAP.33pF50VCHGRM39CH330J50PTK221742231-Be2
C 4132 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Bd4
C 4133 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bg6
C 4134 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bf6
C 4135 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bf6
C 4136 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bd4
C 4137 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bd5
C 4138 CHIP CAP.0.0047uF50VBGRM39B472M50PTK221748171-AF1
C 4139 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Be1
C 4140 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bc3
C 4141 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bd2
C 4142 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Be1
C 4143 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AD3
C 4144 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bd3
C 4145 CHIP TA.CAP.0.1uF35VTESVA1V104M1-8RK781600251-Bc4
C 4145 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248056-Bc4
C 4146 CHIP CAP.1uF10VFGRM39F105Z10PTK221050011-AF3
C 4147 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AG5
C 4148 AL.ELECTRO.CAP.100uF10VRC3-10V101M 100UFK401090301-AD1
C 4148 AL.ELECTRO.CAP.100uF16VECEV1CA101WPK481200126-AD1
C 4149 CHIP CAP.68pF50VCHGRM39CH680J50PTK221742311-Be2
C 4150 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bd2
C 4151 CHIP TA.CAP.47uF6.3VTEMSVB20J476M-8RK780800481-Bd1
C 4152 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bd1
C 4153 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-AF4
C 4154 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bd2
C 4155 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bd1
C 4156 AL.ELECTRO.CAP.22uF16VECEV1CA220SRK481200021-AE2
C 4157 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Be3
C 4158 CHIP CAP.15pF50VCHGRM39CH150J50PTK221742151-Bb5
C 4161 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Bc5
C 4162 CHIP CAP.1uF10VFGRM39F105Z10PTK221050011-Bd2
C 4162 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000286-Bd2
C 4163 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bc5
C 4164 CHIP CAP.0.015uF25VBGRM39B153K25PTK221448051-Bb5
C 4165 CHIP CAP.0.015uF25VBGRM39B153K25PTK221448051-Bb5
C 4166 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Bc5
C 4167 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-AF3
C 4168 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-AF3
C 4169 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AF3
C 4170 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bc2
C 4171 CHIP CAP.1uF10VFGRM39F105Z10PTK221050011-Bd1
C 4171 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000286-Bd1
C 4172 CHIP CAP.0.015uF25VBGRM39B153K25PTK221448051-Bb5
C 4173 CHIP CAP.0.0018uF50VBGRM39B182M50PTK221748121-AF3
C 4174 CHIP CAP.0.0039uF50VBGRM39B392K50PTK221748301-AF3
C 4175 CHIP CAP.0.0039uF50VBGRM39B392K50PTK221748301-AF3
C 4176 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bc2
C 4177 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-AE2
C 4178 CHIP CAP.0.0015uF50VBGRM39B152M50PTK221748111-AF3
C 4180 CHIP CAP.0.0022uF50VBGRM39B222K50PTK221748221-Bc3
C 4181 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-AG3
C 4182 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bc3
C 4183 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-AF2
C 4183 CHIP CAP.1uF10VBGRM40B105K10PTK221008026-AF2
C 4184 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bc2
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
63
Page 64
CNTL Unit
REF.
C 4185 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bb4
C 4186 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bc2
C 4187 CHIP CAP.82pF50VCHGRM39CH820J50PTK221742331-Bc3
C 4188 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bc4
C 4189 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Bc3
C 4190 CHIP CAP.0.015uF25VBGRM39B153K25PTK221448051-Bb5
C 4191 CHIP CAP.560pF50VBECUV1H561KBVK221796111-Bc3
C 4192 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AF1
C 4193 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-39Bc1
C 4193 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK78140013 VERSION A 40-Bc1
C 4193 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK78120031 VERSION C 40-Bc1
C 4194 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Bc3
C 4195 CHIP CAP.150pF50VCHGRM39CH151J50PTK221742391-Bc1
C 4196 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-Bc2
C 4197 CHIP CAP.0.015uF25VBGRM39B153K25PTK221448051-Bb5
C 4198 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bc3
C 4199 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-AF2
C 4200 CHIP CAP.47pF50VCHGRM39CH470J50PTK221742271-Bc2
C 4201 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-AG4
C 4202 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba3
C 4203 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bc4
C 4204 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bc3
C 4205 CHIP CAP.0.01uF25VBGRM39B103K25PTK221448031-Bc4
C 4206 CHIP CAP.150pF50VCHGRM39CH151J50PTK221742391-Bb4
C 4207 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AH1
C 4208 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AG4
C 4209 CHIP CAP.0.0015uF50VBGRM39B152M50PTK221748111-Bb4
C 4210 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Ba3
C 4211 CHIP CAP.15pF50VCHGRM39CH150J50PTK221742151-Bc3
C 4212 CHIP CAP.0.0022uF50VBGRM39B222K50PTK221748221-Bc3
C 4213 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-AF2
C 4214 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Bc4
C 4215 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AG5
C 4216 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bd1
C 4217 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bc1
C 4219 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bc1
C 4220 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bc1
C 4221 CHIP CAP.100pF50VCHGRM39CH101J50PTK221742351-Bc1
C 4222 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Bc4
C 4223 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Bc1
C 4224 CHIP CAP.0.1uF16VBGRM39B104K16PTK221248051-AH4
C 4225 AL.ELECTRO.CAP.10uF35VRC2-35V100MS-F1K401690251-AG2
C 4226 CHIP CAP.150pF50VCHGRM39CH151J50PTK221742391-Bc2
C 4227 CHIP CAP.0.0033uF50VBGRM39B332M50PTK221748151-AI4
C 4228 CHIP CAP.270pF50VCHGRM39CH271J50PTK221742511-AG1
C 4229 CHIP TA.CAP.4.7uF16VTEMSVA1C475M-8RK781200311-Bc3
C 4230 AL.ELECTRO.CAP.10uF16VECEV1CS100SRK481200011-AH4
C 4231 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bb4
C 4232 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba1
C 4233 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000281-Bc4
C 4234 CHIP CAP.680pF25VCHGRM39CH681J25PTK221442031-AG1
C 4235 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Bc2
C 4236 CHIP CAP.560pF50VBECUV1H561KBVK221796111-Bb4
C 4237 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AF2
C 4238 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400131-Ba2
C 4239 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba3
C 4240 CHIP CAP.33pF50VCHGRM39CH330J50PTK221742231-Bb5
C 4241 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-AF2
C 4242 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba2
C 4243 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bc3
C 4244 CHIP CAP.0.0012uF50VBGRM39B122K50PTK221748261-AG2
C 4245 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba3
C 4246 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bb4
DESCRIPTION
VALUEV/WTOL.VXSTD P/NMFR’S DESIGVERS.
SIDE LAY ADR
LOT.
64
Page 65
CNTL Unit
REF.
C 4247 AL.ELECTRO.CAP.470uF16VRE3-16V471M 470UFK401290661-AI4
C 4248 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742531-Bb4
C 4249 CHIP CAP.220pF50VCHGRM39CH221J50PTK221742431-AG2
C 4250 AL.ELECTRO.CAP.10uF35VRC2-35V100MS-F1K401690251-AG3
C 4251 CHIP CAP.0.1uF25VBGRM40B104M25PTK221408111-Ba4
C 4252 CHIP CAP.120pF50VCHGRM39CH121J50PTK221742371-AG2
C 4253 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba2
C 4254 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba2
C 4255 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba5
C 4256 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba2
C 4257 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748211-Ba2
C 4258 AL.ELECTRO.CAP.470uF16VRE3-16V471M 470UFK401290661-AH5
C 4259 CHIP CAP.0.0022uF50VBGRM39B222K50PTK221748221-AG2
C 4260 CHIP CAP.0.0047uF50VBECJ1VB1H472KK221796226-AE2
C 4261 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748216-AE2
C 4263 CHIP CAP.220pF50VCHGRM39CH221J50PTK221742436-AE2
C 4265 CHIP CAP.0.012uF50VBGRM39B123K50PTK221748256-Bd2
C 4266 CHIP CAP.330pF50VCHGRM39CH331J50PTK221742536-AE2
C 4267 CHIP CAP.56pF50VCHGRM39CH560J50PTK221742296-AE3
C 4269 CHIP CAP.0.033uF16VBECJ1VB1C333KK221295156-Bd2
C 4270 CHIP CAP.0.0015uF50VBGRM39B152K50PTK221748276-AE2
C 4272 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000286-Be3
C 4273 CHIP CAP.0.022uF25VBGRM39B223K25PTK221448076-AE3
C 4274 CHIP CAP.0.056uF16VBGRM39B563K16PTK221248076-AE3
C 4275 CHIP CAP.0.0027uF50VBECJ1VB1H272KK221796196-AE3
C 4276 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000286-Bd3
C 4277 CHIP CAP.0.0018uF50VBECJ1VB1H182KK221796176-AF3
C 4278 CHIP CAP.0.056uF16VBGRM39B563K16PTK221248076-Bd3
C 4279 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400136-Bd4
C 4280 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748216-Bd3
C 4281 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400136-Bd3
C 4282 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748216-Bd4
C 4283 CHIP TA.CAP.10uF10VTEMSVA1A106M-8RK781000286-Bd4
C 4284 CHIP TA.CAP.1uF25VTEMSVA1E105M-8RK781400136-AE2
C 4285 CHIP CAP.0.001uF50VBGRM39B102K50PTK221748216-Be2
C 4287 CHIP CAP.0.033uF16VBECJ1VB1C333KK221295156D 4001 DIODEDA204K T146G20703881-Bh2
D 4002 DIODEDA204K T146G20703881-Bh1
D 4003 DIODEDA204K T146G20703881-Bh1
D 4004 DIODEDA204K T146G20703881-Bh1
D 4005 DIODEDA204K T146G20703881-Bh1
D 4006 DIODEDA204K T146G20703881-AB2
D 4007 DIODED1F20-4063G20704741-Bh3
D 4008 DIODEHZM7C-TRG20700701-Bh3
D 4008 DIODEHZM7.5NB2 TRG207086449-Bh3
D 4009 DIODEDA204K T146G20703881-AB4
D 4010 DIODE1SS355 TE-17G20704701-Bh4
D 4011 DIODE1SS355 TE-17G20704701-Bh3
D 4012 DIODEDA204K T146G20703881-AB5
D 4013 DIODE1SS355 TE-17G20704701-AB4
D 4014 DIODE1SS355 TE-17G20704701-Bf1
D 4015 DIODEMA729-(TX)G20703201-Bf4
D 4016 DIODEDA204K T146G20703881-AB5
D 4017 DIODEDA204K T146G20703881-Be6
D 4018 DIODEDA204K T146G20703881-Bd5
D 4019 DIODEDA204K T146G20703881-AF5
D 4020 DIODEDA204K T146G20703881-AC5
D 4021 DIODEDA204K T146G20703881-Be4
D 4022 DIODEDA204K T146G20703881-AC5
D 4023 DIODEDA204K T146G20703881-AC5
D 4024 DIODEDA204K T146G20703881-Bb3
D 4025 DIODE1SS184 TE85RG20700091-Ba3
D 4026 DIODE1SS184 TE85RG20700091-Ba2