weslo.com
Model No. WLEL32115.1
Serial No.
Write the serial number in the space above for reference.
Serial
Number
Decal
ACTIVATE YOUR
WARRANTY
To register your product and activate your warranty today, go to my.weslo.com.
CUSTOMER CARE
For service at any time, go to wesloservice.com.
Or call 1-866-699-3756 Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
CAUTION
Read all precautions and instructions in this manual before using this equipment. Keep this manual for future reference.
USER’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . . |
. . . . |
. . . . . . . . . . . . . . . . . . . . . . . .2 |
IMPORTANT PRECAUTIONS. . . . . . . . . . |
. . . . . . . |
. . . . . . . |
. . . . |
. . . . . |
|
3 |
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . |
. . . . |
. . . . . . . . . . . . . . . . . . . . . . . .5 |
PART IDENTIFICATION CHART. . . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . . |
. . . . |
. . . . . . . . . . . . . . . . . . . . . . .6 |
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . . |
. . . . |
. . . . . . . . . . . . . . . . . . . . . . .7 |
HOW TO USE THE HYBRID TRAINER . . |
. . . . |
. . . . |
. . |
. . . . |
. . |
. . . . . . . . . . . 16 |
FCC INFORMATION . . . . . . . . . . . . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . . |
. . . . |
. . . . . . . . . . . . . . . . . . . . . .20 |
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . .21 |
||||||
EXERCISE GUIDELINES. . . . . . . |
. . . . |
. . . . |
. . |
. . . . |
. . |
. . . . . . . . . . . .22 |
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . . |
. . . . |
. . . . . . . . . . . . . . . . . . . . . .24 |
EXPLODED DRAWING. . . . . . . . . . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . . |
. . . . |
. . . . . . . . . . . . . . . . . . . . . .26 |
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover |
||||||
LIMITED WARRANTY. . . . . . . . . . . . . . . . . |
. . . . . . . . |
. . . . . . . . |
. . . . |
. . . . . . . . |
. . . . |
. . . . . . . . . . . . . . Back Cover |
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, see the front cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be
shown at actual size.
WESLO is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your hybrid trainer before using your hybrid trainer. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1.It is the responsibility of the owner to ensure that all users of the hybrid trainer are adequately informed of all precautions.
2.Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.
3.The hybrid trainer is not intended for use by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, unless they are given supervision or instruction about use of the hybrid trainer by someone responsible for their safety.
4.Use the hybrid trainer only as described in this manual.
5.The hybrid trainer is intended for home use only. Do not use the hybrid trainer in a commercial, rental, or institutional setting.
6.Keep the hybrid trainer indoors, away from moisture and dust. Do not put the hybrid trainer in a garage or covered patio or near water.
7.Place the hybrid trainer on a level surface, with at least 3 ft. (0.9 m) of clearance in the front and rear of the hybrid trainer and 2 ft. (0.6 m) on each side. To protect the floor or carpet from damage, place a mat under the hybrid trainer.
8.Inspect and properly tighten all parts each time the hybrid trainer is used. Replace any worn parts immediately.
9.Keep children under age 13 and pets away from the hybrid trainer at all times.
10.The hybrid trainer should not be used by persons weighing more than 250 lbs. (113 kg).
11.Wear appropriate clothes while exercising; do not wear loose clothes that could
become caught on the hybrid trainer. Always wear athletic shoes for foot protection while exercising.
12.Hold the handlebars or the upper body arms when mounting, dismounting, or using the hybrid trainer.
13.Make sure that the pedal knobs are fully tightened each time you use the hybrid trainer.
14.The heart rate monitor is not a medical device. Various factors may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general.
15.The hybrid trainer does not have a freewheel; the pedals will continue to move until the flywheel stops. Reduce your pedaling speed in a controlled way.
16.Keep your back straight while using the hybrid trainer; do not arch your back.
17.Over exercising may result in serious injury or death. If you feel faint, if you become short of breath, or if you experience pain while exercising, stop immediately and cool down.
3
STANDARD SERVICE PLANS
all
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary WESLO® MOMENTUM G 3.2 hybrid trainer. The MOMENTUM G 3.2 hybrid trainer provides an impressive selection of features designed to make your workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before you use the hybrid trainer. If you have questions after
reading this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.
Length: 4 ft. 3 in. (130 cm) |
|
Width: 2 ft. 1 in. (64 cm) |
|
|
Console |
Heart Rate Monitor |
|
Handlebar |
|
Resistance Knob |
|
|
Upper Body Arm |
Water Bottle Holder* |
|
Seat |
Seat Post Knob |
|
|
Seat Knob |
Pedal |
|
|
Leveling Cap |
*Water bottle is not included |
|
5 |
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it has been preassembled. Extra parts may be included.
M8 Locknut |
|
M8 Acorn Nut |
|
M10 Locknut |
|
Left Crank |
|
Right Crank |
(53)–2 |
|
(58)–6 |
|
(93)–6 |
Locknut (37)–1 |
Locknut (36)–1 |
||
M8 Split |
|
M8 Curved |
|
M8 Washer |
M8 Large |
|
M8 Plastic |
|
Washer (63)–13 |
|
Washer (101)–2 |
(55)–14 |
Washer (72)–2 |
|
Washer (27)–2 |
||
Wave Washer |
M10 Washer |
M10 Plastic |
|
M12 Split |
||||
(73)–2 |
|
(92)–8 |
Washer (62)–4 |
Washer (74)–2 |
||||
M4 x 12mm |
M8 x 20mm |
M8 x 20mm Hex |
|
M8 x 60mm |
||||
Screw (66)–6 |
Screw (54)–3 |
Screw (57)–2 |
|
Bolt (90)–2 |
||||
M8 x 35mm Screw (86)–2 |
M8 x 40mm Bolt (56)–4 |
|
M10 x 45mm Bolt (91)–4 |
|||||
M8 x 65mm Carriage Bolt (51)–2 |
|
M8 x 65mm Bolt (100)–2 |
||||||
|
|
|
M10 x 70mm Bolt (60)–2 |
|
|
|
|
|
|
|
|
|
6 |
|
|
|
|
ASSEMBLY
•To hire an authorized service technician to assemble the hybrid trainer, call 1-800-445-2480.
•Assembly requires two persons.
•Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish assembly.
•Left parts are marked “L” or “Left” and right parts are marked “R” or “Right.”
•To identify small parts, see page 6.
•In addition to the included tool(s), assembly requires the following tools:
one Phillips screwdriver
one adjustable wrench
one pair of pliers
one rubber mallet
Assembly may be easier if you have a set of wrenches. To avoid damaging parts, do not use power tools.
1. Go to my.weslo.com on your computer and |
|
|
|
|
|
|
|
|
1 |
|
|
register your product. |
|
|
|
|
|
|
•documents your ownership
•activates your warranty
•ensures priority customer support if assistance is ever needed
Note: If you do not have internet access, call Customer Care (see the front cover of this manual) and register your product.
2. Identify the Rear Stabilizer (28), which has a |
2 |
|
Leveling Cap (33) on each end. |
|
|
|
|
|
While a second person lifts the rear of the Frame |
|
|
(1), attach the Rear Stabilizer (28) to the Frame |
|
|
with two M8 x 65mm Bolts (100); start both |
|
|
Bolts, and then tighten them. |
|
|
|
33 |
|
|
28 |
1 |
|
|
|
|
|
33 |
|
100 |
|
|
7 |
|
3.While a second person lifts the front of the Frame (1), attach the Front Stabilizer (10) to the Frame with two M8 x 65mm Carriage Bolts (51), two M8 Curved Washers (101), two M8 Split Washers (63), and two M8 Acorn Nuts (58); insert both Carriage Bolts, and then tighten the Acorn Nuts.
4.While a second person holds the Upright (2) near the Frame (1), connect the Upright Wire (31) to the Reed Switch Wire (47).
Next, connect the Resistance Cable (25) to the Lower Cable (42) in the following way:
See inset drawing A. Pull upward on the metal bracket on the Lower Cable (42), and insert the tip of the Resistance Cable (25) into the wire clip inside the metal bracket.
See inset drawing B. Firmly pull the Resistance Cable (25) and slide it into the metal bracket on the Lower Cable (42).
See inset drawing C. Using pliers, squeeze together the prongs on the upper end of the metal bracket.
3 |
|
|
|
|
58 63 101 |
1 |
|
10 |
|
|
|
|
||
|
|
|
|
51 |
|
58 |
63 |
101 |
|
4 |
|
|
A |
25 |
|
|
|
|
|
|
|
|
|
42 |
|
|
|
B |
25 |
|
|
|
|
42 |
|
2 |
|
C |
|
|
|
|
|
|
31 |
25 |
|
|
|
47 |
|
|
|
|
42 |
|
|
|
|
|
|
|
|
|
1 |
|
|
|
|
8
5. Tip: Avoid pinching the wires and cables |
5 |
|
|
|
|
|
during this step. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Slide the Upright (2) onto the Frame (1). |
|
|
|
|
|
|
Attach the Upright (2) with three M8 x 20mm |
|
|
|
|
|
|
Screws (54), three M8 Split Washers (63), and |
|
|
|
|
|
|
three M8 Washers (55). Do not tighten the |
|
|
|
|
|
|
Screws yet. |
Avoid pinching the |
|
|
|
||
See the inset drawing. Attach the Upright |
|
|
|
|||
wires and cables |
|
|
|
|||
(2) with two M8 x 60mm Bolts (90), four M8 |
|
|
|
|
|
|
Washers (55), and two M8 Locknuts (53). Do |
|
|
|
|
|
|
not tighten the Locknuts yet. |
54 |
|
|
|
|
|
|
63 |
55 |
|
2 |
|
|
|
54 |
|
|
|
55 |
|
|
|
|
|
63 |
|
|
|
|
63 |
55 |
|
54 |
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
2 |
|
|
|
90 |
|
|
53 |
|
|
|
|
|
|
|
|
|
|
|
55 |
|
55 |
|
|
|
|
|
|
|
|
|
|
90 |
|
1 |
53 |
|
|
|
|
|
||
|
|
|
|
|
|
|
9
Loading...