Ubiquiti UniFi Switch 48 US-48-500W, UniFi Switch 48 US-48-750W Quick Start Manual

Managed PoE+ Gigabit
Switch with SFP+

Models: US-48-500W, US-48-750W

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®
Switch with SFP+ and SFP. The UniFi Controller software and
User Guide are available for download at:

downloads.ubnt.com/unifi

This Quick Start Guide is designed to guide you through the
installation and show you how to access the Configuration
Interface. This Quick Start Guide also includes the warranty
terms, and is for use with the UniFi Switch with SFP+ and SFP,

modelUS‑48‑500W or US‑48‑750W. (The hardware description

and installation instructions are the same for both models.)

Package Contents

UniFi Switch

Managed PoE+ Gigabit
Switch with SFP+

Models: US-48-500W, US-48-750W

Power Cord Mounting Screws

(#10‑32 x 5/8", Qty. 4)

Cage Nuts

(#10‑32 x 5/8", Qty. 4)

Quick Start

Guide

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft

Internet Explorer 8 (or above)

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s

responsibility to follow local country regulations and indoor cabling requirements.

Network Topology Requirements

• A DHCP‑enabled network for the UniFi Switch to obtain an

IPaddress (connected devices will also obtain IP addresses

after deployment)

• A management station running the UniFi Controller

software, located either on‑site and connected to the same
Layer2 network, or off‑site in a cloud or NOC

UniFi Switch

UniFi

Security

Gateway

Internet

O-Site

Cloud/NOC

On-Site

Management

Station

UAP-AC UAP-PRO

LAN

WAN

Network Health

www

WAN LAN

WLAN

VOIP

www

WAN LAN WLAN VOIP

IP

DNS

GATEWAY

ACTIVE CLIENTS

DOWN

UP

SWITCHES

USERS

GUESTS

DOWN

UP

APS

USERS

GUESTS

DOWN

UP

PHONES

EXTENSION

CALLS IN

CALLS OUT

XXX.XXX.XXX.XXX

XXX.XXX.XXX.XXX

192

0

0

0

0

0

0

162

2

0

0

0

30

4

3

6

0

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENT SITE

Default

REFRESH RATE

2 minutes

Network Health

www

WAN LAN

WLAN

VOIP

www

WAN LAN WLAN VOIP

IP

DNS

GATEWAY

ACTIVE CLIENTS

DOWN

UP

SWITCHES

USERS

GUESTS

DOWN

UP

APS

USERS

GUESTS

DOWN

UP

PHONES

EXTENSION

CALLS IN

CALLS OUT

XXX.XXX.XXX.XXX

XXX.XXX.XXX.XXX

192

0

0

0

0

0

0

162

2

0

0

0

30

4

3

6

0

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENT SITE

Default

REFRESH RATE

2 minutes

or

UAP-Outdoor+

Sample Network Diagram

All UniFi devices support off‑site management controllers.
For setup details, refer to the User Guide on the website:

documentation.ubnt.com/unifi

Hardware Overview

Front Panel System LED

System

State Status

White Factory defaults, waiting for integration.

Flashing White Initializing.

Alternating
White/Blue

Device is busy; do not use or unplug it.

This usually indicates that a process such
as a firmware upgrade is taking place.

Blue

Successfully integrated into a network
and working properly.

Flashing Blue

This is used to locate a device.

When you click Locate in the UniFi
Controller software, the System LED

will flash blue. The software will also
display the location of the UniFi Switch
on the map.

Front Panel Port LEDs

RJ45: PoE

RJ45: Speed/Link/Act

SFP: Speed/Link/Act

SFP+: Speed/Link/Act

LED State Status

RJ45 1‑48

PoE

Off No PoE

Amber IEEE 802.3af/802.3at

Green 24V Passive

Speed/

Link/

Act

Off No Link

Amber

Link Established at

10/100Mbps
Flashing Indicates Activity

Green

Link Established at

1000Mbps
Flashing Indicates Activity

SFP+ 1‑2

Speed/

Link/

Act

Off No Link

Green

Link Established at 1Gbps
Flashing Indicates Activity

White

Link Established at

10Gbps
Flashing Indicates Activity

SFP 1‑2

Speed/

Link/

Act

Off No Link

Green

Link Established at 1Gbps
Flashing Indicates Activity

Front Panel Ports

RJ45 1-48

SFP 1-2

SFP+ 1-2

Port Description

RJ45 1‑48

RJ45 ports support Power over Ethernet (PoE)
and 10/100/1000 Ethernet connections.

SFP+ 1‑2

Hot‑swappable SFP+ ports support
1/10Gbps connections.

SFP 1‑2

Hot‑swappable SFP ports support 1 Gbps

connections.

Front Panel Button

Reset

Button Description

Reset

This button serves two functions for the
UniFi Switch:

• Restart Press and release the Reset
button quickly.

• Restore to Factory Default

Settings Press and hold the Reset button

for more than five seconds.

*640-00116-04*

640-00116-04

Back Panel

CONSOLE

Mounting Holes

Power

Mounting Holes

Console

Note: The Console port is reserved for future use.

Side Panels

Ventilation Holes

Fans

Installation Requirements

• Phillips screwdriver

• Standard‑sized, 19" wide rack with a minimum of 1U height

available

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your outdoor networks
from the most brutal environments and devastating ESD
attacks with industrial‑grade shielded Ethernet cable,
TOUGHCable™, from Ubiquiti Networks. For more details,

visit: www.ubnt.com/toughcable

Note: Although the cabling can be located outdoors,

the UniFi Switch itself should be housed inside a
protective enclosure.

Hardware Installation

1. Connect the Power Cord to the Power port of the
UniFiSwitch.

2. Attach the UniFi Switch to the rack using the four Mounting

Screws. (If the rack has square slots, then use the Cage Nuts
with the Mounting Screws.)

Note: Keep 20 mm of clearance next to the

ventilation holes for adequate airflow.