Troy-bilt TB2BP EC User Manual

TB2BP EC

2-Cycle Electric Start Capable

Backpack Blower

Operator’s Manual

Remove Unit From Carton

Assemble The Unit

Tools Required-

Phillips Screwdriver

T-20 Torx® Screwdriver

1	2		3
Remove all contents from	Place a hose clamp over		Place a hose clamp over
the carton.	the end of the Flex Tube		the other end of Flex Tube
	and slide the end of the		and slide the end over the
	with the clamp on it over		top end of the upper
	the elbow tube. Tighten		blower tube. Tighten the
	the clamp screw.		clamp screw.
Assemble The Unit
	40:1
	1 Gallon	3.2 oz
6	7		8
Loosen the 2 screws on	Mix thoroughly in separate		Place unit on a level
the throttle control. Move	fuel can:		urface and fill fuel tank.
the throttle control to the	– 3.2 fl. oz. of 2-cycle		DO NOT overfill.
position that provides the	engine oil
best grip and tighten.	– 1 gallon of unleaded

gasoline

NOTE: Do not mix directly in fuel tank.

Start The Unit

4	5
Insert the upper blower	Insert the lower blower
tube into the lower blower	tube into the nozzle and
tube and twist the lower	twist the nozzle clockwise
tube clockwise unit it locks	until it locks into place.
into place.	Zip tie the throttle cable to
	the elbow tube.
Start The Unit
Primer
Bulb

9	10 X	10
Press primer bulb 10		Move choke lever to
times, or until fuel is		Position 1.
visible

Flex Tube

On/ Off Switch

Cruise Control

Spark Plug

Throttle Control

Starter Rope

Lower Blower Tube

Nozzle	Upper Blower
	Tube

Choke Lever

Primer Bulb

Fuel Cap

DIDN’T START?

Repeat these instructions.

IF the engine hesitates, return the choke lever to Position 2 and continue the warm-up.

IF the engine does not start, go back to step 9.

IF the unit fails to start after 2 attempts, move choke lever to Position 3 and pull rope until unit starts

SLOW						SLOW
FAST						FAST
		5 X
11	12	13	14	15	16	17
Press down cruise control	Crouch in starting	Pull rope 5 times.	Move choke lever to	Pull rope 3-5 times to	Move choke lever to	Continue to keep the
to FAST position.	position.		Position 2 .	start engine. Keep the	Position 3.	cruise control in FAST
				cruise control in FAST		position and warm unit for
				position and allow unit to		an additional 60 seconds
				warm up for 30 to 60		to complete warm-up. Unit
				seconds.		may be used during this
						time.

ENGLISH — PAGE 1

ESPAÑOL — PAGE 7

IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.

NEED HELP? Call 1-800-828-5500 in U.S. or 1–800–668–1238 in Canada

769-07848 P00

04/12

SERVICE INFORMATION
TABLE OF CONTENTS
Rules for Safe Operation........................................................................................................................	2
Oil and Fuel Information.........................................................................................................................	3
Operating Instructions............................................................................................................................	4
Maintenance and Repair Instructions.....................................................................................................	4
Cleaning and Storage.............................................................................................................................	5
Troubleshooting Chart............................................................................................................................	5
Optional Accessory................................................................................................................................	5
Specifications.........................................................................................................................................	5
Warranty...............................................................................................................................................	16

All information, illustrations, and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

Copyright© 2012 MTD SOUTHWEST INC, All Rights Reserved.

For service, please call 1-800-828-5500 in the United States, or 1-800-668-1238 in Canada to obtain a list of authorized service dealers near you. For more details about your unit, visit our website at www.troybilt.com or www.troybilt.ca

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, please call the Customer Support Department.

Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer.

RULES FOR SAFE OPERATION

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington.

All U.S. Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washingtonrequire,bylawthatcertaininternalcombustionenginesoperatedonforestbrushand/orgrasscovered areas be equipped with a spark arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If it requires replacement, ask your LOCAL SERVICE DEALER to install the Accessory Part #753-06418 Muffler Assembly

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

Symbol Meaning

WARNING: Failure to obey a safety warning can result in injury to yourself and others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

SAFETY ALERT: Indicates danger, warning or caution. Attention is required in order to avoid serious personal injury. May be used in conjunction with other symbols or pictographs.

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

NOTE: Advises of information or instructions vital to the operation or maintenance of the equipment.

Read the Operator’s Manual and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-828-5500 IN THE U.S. OR 1-800-668-1238 IN CANADA

• IMPORTANT SAFETY INSTRUCTIONS •

READ ALL INSTRUCTIONS BEFORE OPERATING

WARNING: When using the unit, all safety rules must be followed. Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders. Please keep these instructions for later use.

CALIFORNIA PROPOSITION 65

WARNING: Engine exhaust, some of its constituents and certain finished components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

•Read the instructions carefully. Be familiar with the controls and proper use of the unit.

•Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.

•Children and teens under the age of 15 must not use the unit, except for teens guided by an adult.

•All guards and safety attachments must be installed properly before operating the unit.

•Inspect the unit before use. Replace damaged parts. Check for fuel leaks. Make sure all fasteners are in place and secure. Replace parts that are cracked, chipped, or damaged in any way. Do not operate the unit with loose or damaged parts.

•Carefully inspect the area before starting the unit. Remove all debris and hard or sharp objects such as glass, wire, etc.

•Clear the area of children, bystanders, and pets. At a minimum, keep all children, bystanders, and pets outside a 50 feet (15 m.) radius; there still may be a risk to bystanders from thrown objects. Bystanders should be encouraged to wear eye protection. If you are approached, stop the unit immediately.

•Squeeze the throttle control and check that it returns automatically to the idle position. Make all adjustments or repairs before using unit.

•Never store the unit, with fuel in the tank, inside a building where fumes may reach an open flame (pilot lights, etc.) or sparks (switches, electrical motors, etc.).

•Allow the engine to cool before storing or transporting. Be sure to secure the unit while transporting.

•Store the unit in a dry place, either locked up or up high to prevent unauthorized use or damage. Keep out of the reach of children.

•Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean, and free from debris. Clean after each use, see Cleaning and Storage instructions.

•Keep these instructions. Refer to them often and use them to instruct other users. If you loan this unit to others, also loan these instructions to them.

•Wear safety glasses or goggles that are marked as meeting ANSI Z87.1–1989 standards and are marked as such. Wear ear/hearing protection when operating this unit.

•Never run the unit without the the proper equipment attached.

•To reduce the risk of hearing loss associated with sound level(s), always wear ear/hearing protection when operating this unit.

•Wear heavy long pants, boots, gloves, and a long sleeve shirt. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level.

•Use the unit only in daylight or good artificial light.

•Keep outside surfaces free from oil and fuel.

•Avoid accidental starting. Be in the starting position whenever pulling the starter rope. The operator and unit must be in a stable position while starting. Refer to Starting/Stopping Instructions.

•Do not set unit on any surface except a clean, hard area while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out by the discharge opening, damaging unit, property, or causing serious injury to bystanders or operator.

•Use the right tool. Only use this tool for its intended purpose.

•Do not force unit. It will do the job better and with less likelihood of injury at a rate for which it was designed.

•Do not overreach or use from unstable surfaces such as ladders, trees, steep slopes, rooftops, etc. Always keep proper footing and balance.

•Always hold the unit with a firm grip when operating.

•Keep hands, face, and feet away from all moving parts. Do not touch or try to stop the impeller when it is rotating. Do not operate without guards in place.

RULES FOR SAFE OPERATION

•Do not put any object into openings. Do not use with any opening blocked; keep free of dirt, debris, and anything that may reduce the air flow.

•Do not touch the engine or muffler. These parts get extremely hot from operation, even after the unit is turned off.

•Do not operate the engine faster than the speed needed to do the job. Do not run the engine at high speed when not in use.

•Always stop the engine when operation is delayed or when walking from one location to another.

•Use only genuine factory replacement parts and accessories for this unit. These are available from your authorized service dealer. Use of any unauthorized parts or accessories could lead to serious injury to the user or damage to the unit, and void your warranty.

•If you strike or come into contact with a foreign object, stop the engine immediately and check for damage. Do not operate before repairing damage. Do not operate the unit with loose or damaged parts.

•To reduce fire hazard, replace faulty muffler and spark arrestor. Keep the engine and muffler free from grass, leaves, excessive grease or carbon build up.

OIL AND FUEL SAFETY

WARNING: Gasoline is highly flammable and its vapors can explode if ignited. Take the following precautions:

•Store fuel only in containers specifically designed and approved for the storage of such materials.

•Always stop the engine and allow it to cool before filling the fuel tank. Never remove the fuel tank cap or add fuel when the engine is hot. Never operate the unit without the fuel cap securely in place.

•Always mix or add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Do not smoke.

•Never Operate the unit without the fuel cap securely in place.

•Avoid creating a source of ignition for spilled fuel. Wipe up any spilled fuel from the unit immediately before starting the unit. Move the unit at least 30 feet (9.1 m) from the fueling source and site before starting the unit. Do not smoke.

•Never start or run the unit inside a closed room or building. Breathing exhaust fumes can be fatal. Operate this unit only in a well-ventilated outdoor area.

•Check the unit for fuel leaks.

•Loosen the fuel tank cap slowly to relieve any pressure in the tank.

•Never store the unit with fuel in the tank, inside a building where fumes may reach an open flame (pilot lights, etc.) or sparks (switches, electrical motors, etc.).

•To reduce fire hazard, replace a faulty muffler and spark arrestor. Keep the engine and muffler free from grass, leaves, excessive grease or carbon build up.

•Avoid accidental starting. Be in the starting position whenever pulling the starter rope. The operator and unit must be in a stable position while starting. Refer to Starting/Stopping Instructions.

•Do not touch the engine, gear housing or muffler. These parts get extremely hot from operation, even after the unit is turned off.

•Turn the engine to off and disconnect the spark plug for maintenance or repair.

BLOWER SAFETY

•Stop the engine for maintenance, repair, to install or remove the blower tubes. The unit must be stopped and the impeller no longer turning to avoid contact with the rotating blades.

•Never point the blower in the direction of bystanders, animals, windows or automobiles.

SAVE THESE INSTRUCTIONS

2

RULES FOR SAFE OPERATION

• SAFETY & INTERNATIONAL SYMBOLS •

This operator’s manual describes safety and international symbols and pictographs that may appear on this product. Read the operator’s manual for complete safety, assembly, operating and maintenance and repair information.

Symbol Meaning

•SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.

•READ OPERATOR’S MANUAL

WARNING: Read the operator’s manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.

•WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can cause severe eye injury and hearing loss. Wear eye protection meeting ANSI Z87.1-1989 standards and ear protection when operating this unit. Use a full face shield when needed.

•UNLEADED FUEL

Always use clean, fresh unleaded fuel

•DO NOT USE E85 FUEL IN THIS UNIT

WARNING: It has been proven that fuel containing greater than 10% ethanol will likely damage this engine and void the warranty.

•ON/OFF CONTROL

ON / START / RUN

•ON/OFF CONTROL

OFF or STOP

•OIL

Refer to operator’s manual for the proper type of oil.

•PRIMER BULB

Push primer bulb, fully and slowly, 10 times.

• CHOKE CONTROL

1.• FULL choke position

2.• PARTIAL choke position

3.• RUN choke position

• THROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY

WARNING: Small objects can be propelled at high speed, causing injury. Keep away from the rotating rotor.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially children and pets, at least 50 feet (15 m.) from the operating area.

•HOT SURFACE

WARNING: Do not touch any metal engine components. The engine gets

extremely hot from operation and may cause severe burns. Allow the unit to completely cool prior to any maintence or servicing.

• BLOWERS – ROTATING IMPELLER BLADES CAN CAUSE SEVERE INJURY

WARNING: Stop the engine and allow the impeller to stop before opening the vacuum door, installing or changing tubes or bag, or before cleaning or performing any maintenance.

OIL AND FUEL

OIL AND FUEL MIXING INSTRUCTIONS

WARNING: Gasoline is extremely flammable. Ignited vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area.

WARNING: Add fuel in a clean, level and well ventilated outdoor area. Wipe up any spilled fuel immediately. Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors dissipate.

WARNING: Remove fuel cap slowly to avoid injury from fuel spray. Never operate the unit without the fuel cap securely in place.

Be sure to use fresh, clean unleaded fuel and follow instructions carefully for proper fuel/oil mixture.

Definition of Blended Fuels

WARNING: Fuel containing greater than 10% ethanol will likely damage the engine and void the warranty.

Today’s fuels are often a blend of gasoline and oxygenates such as ethanol, methanol, or MTBE (ether) which absorb water. Use fuel within 30 days of purchase. Blended fuels older than 30 days will affect the performance and life of the engine.

Using Blended Fuels

If the use of blended fuel is unavoidable, follow recommended precautions:

•Always use the fresh fuel mix explained in the operator’s manual

•Always agitate the fuel mix before fueling the unit

•Drain the tank and run the engine dry before storing the unit

Using Fuel Additives

It is recommended to use the manufacturers 2-cycle oil with this unit. If unavailable, use a good 2-cycle oil designed for air-cooled engines along with a fuel additive, such as STA-BIL® Gas Stabilizer or an equivalent.

Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to the instructions on the container. NEVER add fuel additives directly to the unit’s fuel tank.

Mixing The Fuel

Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded fuel in a separate fuel can. Use a 40:1 fuel/oil ratio. Do not mix them directly in the engine fuel tank.

IF...the unit came with a bottle of 2-cycle oil; pour the entire bottle into 1 gallon of gas and mix thoroughly.

NOTE: One gallon (3.8 liters) of unleaded fuel mixed with one 3.2 oz. (95 ml.) bottle of 2-cycle oil makes a 40:1 fuel/oil ratio.

NOTE: Dispose of the old fuel/oil mix in accordance to federal, state and local regulations.

IF USING THE OPTIONAL ELECTRIC STARTER OR POWER START

BIT™ ACCESSORY TO START THE UNIT

HOW TO START THE UNIT USING THE ELECTRIC STARTER OR POWER START BIT ACCESSORY.

NOTE: This Unit Can Use an Electric Start or Power Start Bit™ Optional Accessory!

Please refer to the Electric Starter or Power Start Bit operator’s manual for proper use of this feature. (Items may be Sold Separately! Please refer to page 5 of this manual about purchasing these accessories.)

STARTING INSTRUCTIONS

1.Mix fuel with oil.

2.Fill the fuel tank with fresh, clean fuel mix.

NOTE: There is no need to turn the unit on. The On/Off Control is in the ON ( I ) position at all times.

3.Fully press and release the primer bulb 10 times, slowly. Some amount of fuel should be visible in the primer bulb. If fuel cannot be seen in the bulb, press and release the bulb until fuel is visible.

4.Move choke lever to Position 1.

5.Press the cruise control down to fast position.

6.Crouch in starting position and place the electric Starter or power Start Bit into the back of the unit. Refer to the operation section of the electric starter or power start bit operator’s manual.

7.Press and hold the electric starter or drill ON (I) button for 2 seconds.

8.Move the choke lever to Position 2.

9.With the cruise control still in the Fast position, press and hold the electric starter or drill ON (I) button for 2-second intervals until the unit starts.

10.Keeping the cruise control in the fast position, remove the electric starter or drill from the unit and allow the engine to warm up for 30 to 60 seconds.

11.Move the choke lever to Position 3 and run the unit for an additional 60 seconds. The unit may be used during this time.

NOTE: Unit is properly warmed up when engine accelerates without hesitation. IF... engine hesitates, return the choke lever to Position 2 and continue warm-up. IF... engine does not start, go back to step 3.

IF WARM... start the unit with the choker lever in Position 2. After the unit starts, move the choker lever to Position 3.

STOPPING INSTRUCTIONS

1.Release the throttle control or move the cruise control to slow and allow the engine to cool down by idling.

2.Press and hold the On/Off Control switch in the OFF (O) position until the unit comes to a complete stop.

3

OPERATION

USING THE CRUISE CONTROL

1.Once the engine has been started and warmed up, squeeze the trigger to accelerate the unit as needed (Fig. 1).

2.For longer periods of operation and to eliminate possible finger fatigue, move the cruise control toward the FAST position to incrementally increase or maintain the unit’s engine speed (Fig. 1). When the cruise control is pressed, the trigger will recede into the handle.

3.To decrease engine speed, move the cruise control to the SLOW position and the trigger will return to the idle position (Fig. 1).

PUTTING ON THE UNIT

1.Place the shoulder supports over the shoulders so that the engine rests on the operator’s back.

2.Pull the shoulder support straps down to tighten the shoulder supports (Fig. 2).

NOTE: The unit must be started prior to putting it on. See Starting/Stopping Instructions.

TAKING OFF THE UNIT

1.Pull up on the bottom tabs of the shoulder support buckles to loosen the shoulder supports (Fig. 3).

2.Remove the unit.

Cruise

Control SLOW

FAST

Fig. 1

Shoulder

Supports

Fig. 2

HOLDING THE BLOWER	Shoulder
	Buckles

Before operating the unit, stand in the operating position and check for the following (Fig. 4):

• The operator is wearing eye protection and proper clothing.

• If the conditions are dusty, the operator is wearing a dust

	mask.
•	The unit is secure and comfortable on the operator’s back.
•	The right arm is slightly bent and the right hand is gripping the	Fig. 3
	throttle control.

OPERATING TIPS

•Never direct the unit at anyone while the unit is in operation.

• Always hold the unit securely when operating.

•To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

• Operate power equipment only at reasonable hours. Comply with times listed in local ordinances. Usual recommendations are 9:00 am to 5:00 pm, Monday through Saturday.

• To reduce noise levels, operate power blowers at the lowest
possible speed to do the job and limit the total number of	Fig. 4
pieces of power equipment used at any one time.

•Check unit before operating, especially muffler, air intakes and air filters, for debris and possible blockages.

•Use rakes and brooms to loosen debris before blowing.

•In dusty conditions, slightly dampen surfaces.

•Conserve water by using power blowers instead of hoses for many lawn and garden applications, including cleaning debri from areas such as screens, patios, grills, porches, and gardens.

•Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away.

•Use the full blower nozzle extension so the air stream can work closer to the ground.

•Clean up after using blowers and other equipment. Dispose of debris appropriately.

•Use the cruise control to make continuous operation easier.

APPLICATIONS

•Use the blower for trees, shrubs, flower beds and hard-to-clean areas.

•Use the unit around buildings and for other normal cleaning procedures.

•Use the blower around walls, overhangs, fences and screens.

MAINTENANCE

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require special tools or skills. For these types of repairs call 1-800-828-5500 for more information.

NOTE: Please read the California/ EPA statement that came with the unit for a complete listing of terms and coverage for the emissions control devices, such as the spark arrestor, muffler, carburetor, etc

FREQUENCY	MAINTENANCE REQUIRED	SEE
Every 10 hours	Clean air filter	p. 4
Every 25 hours	Check the spark plug condition and gap	p. 4

AIR FILTER MAINTENANCE

WARNING: To avoid serious personal injury, always turn the unit off and allow it to cool before cleaning or maintaining it.

Failure to maintain the air filter properly can result in poor performance or cause permanent damage to

	the engine.	Air Filter	Tab
	1. Open the air filter cover and remove the air filter (Fig. 5).
		Cover
	2. Wash the filter in detergent and water. Rinse thoroughly and
	allow to dry.

3. Apply clean SAE 30 motor oil to filter.

4. Squeeze filter to spread and remove excess oil.

5. Replace air filter (Fig. 6).

NOTE: Operating unit without air filter WILL VOID warranty.

6. Reinstall the air filter cover and press down until it snaps into		Fig. 5
place (Fig. 5).
ADJUST IDLE SPEED SCREW	Lock Tabs	Air Filter

The idle speed of the engine is adjustable. An idle adjustment screw is between the air filter cover and the engine cover (Fig. 7).

NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments.

If, after checking the fuel and cleaning the air filter, the engine still will not idle, adjust the idle speed screw as follows:

	1. Start the engine and let it run at a high idle for a minute to	Fig. 6
	warm up. Refer to Starting/Stopping Instructions.
	2. Move the cruise control to the SLOW position and let
	the engine idle. If the engine stops, insert a small Phillips	Idle Adjustment
	screwdriver in between the air filter cover and the engine
		Screw
	cover (Fig. 7). Turn the idle speed screw in, clockwise, 1/8 of a
	turn at a time (as needed) until the engine idles smoothly.
	Checking the fuel mixture, cleaning the air filter, and adjusting the
	idle speed should solve most engine problems. If not and all of the
	following are true:
	• engine will not idle
	• engine hesitates or stalls on acceleration	Fig. 7
	• there is a loss of engine power

take the unit to a qualified service dealer.

REPLACING THE SPARK PLUG

Use a replacement part number 753-06193 or Champion spark plug #RDJ7J. The correct spark gap is 0.025 in. (0.635 mm).

WARNING: Do not sand blast, scrape or clean spark plug electrodes. Grit in the engine could damage the cylinder.

1.Stop the engine and allow it to cool.

2.Grasp plug wire firmly and pull.

3.Clean around spark plug and remove using a 5/8-inch socket

counterclockwise.

4.	Set the air gap, according to specifications, using a feeler
	gauge (Fig. 8).
5.	Install spark plug turning clockwise and torquing as stated:
•	Torque to: 110-120 in.•lb. (12.3-13.5 N•m) Do not over	0.025 in.
	tighten.	(0.635 mm)
6.	Reconnect the spark plug wire.
				Fig. 8

4

CLEANING AND STORAGE

CLEANING

WARNING: To avoid serious personal injury, always turn the unit off and allow it to cool before cleaning or maintaining the unit.

Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic. Wipe off any moisture with a soft cloth.

STORAGE

•Never store a fueled unit where fumes may reach an open flame or spark.

•Allow the engine to cool before storing.

•Lock up the unit to prevent unauthorized use or damage.

•Store the unit in a dry, well-ventilated area.

•Store the unit out of the reach of children.

Long Term Storage

1.Remove the fuel cap, tip the unit and drain the fuel into an approved container. Reinstall the fuel cap.

2.Start the engine and allow it to run until it stalls. This ensures that all fuel has been drained from the carburetor.

3.Allow the engine to cool. Remove the spark plug and put 5 drops of any high quality motor oil or 2-cycle oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug.

4.Thoroughly clean the unit and inspect it for any loose or damaged parts. Repair or replace damaged parts and tighten loose screws, nuts or bolts.

Preparing the Unit for Use after Long Term Storage

1. Remove the spark plug and drain all of the oil from the cylinder.

NOTE: Do not use fuel that has been stored for more than 30 days. Dispose of old fuel according to federal, state and local regulations.

TROUBLESHOOTING

	PROBLEM	SOLUTION
	ENGINE WILL NOT START, IDLE OR ACCELERATE
	Empty fuel tank	Fill fuel tank with fuel
	Primer bulb wasn't pressed enough	Slowly press primer bulb 10 times
	Old fuel	Drain fuel tank and add fresh fuel mix
	Fouled spark plug	Replace or clean the spark plug
	Air filter is plugged	Replace or clean the air filter
	Improper idle speed	Adjust according to the Idle Speed
		Adjustments section.
	ENGINE LACKS POWER OR STALLS
	Old fuel	Drain fuel tank and add fresh fuel mix
	Fouled spark plug	Replace or clean the spark plug

OPTIONAL ACCESSORY

ELECTRIC STARTER AND POWER START BIT™ FEATURES

This unit is designed to be started with an optional electric starter or Power Start Bit™ that are sold separately. If choosing to start the unit using one of these features or have questions please contact your local retailer or call 1-800-828-5500 U.S, (1-800-668-1238 Canada), for more information and purchasing. You may also go to www.troybilt.com or www.troybilt.ca

Electric Start Feature

Fig. 9

	SPECIFICATIONS
UNIT*
Engine Type.............................................................................................................	Air-Cooled, 2-Cycle
Displacement..................................................................................................................................	27 cc
Idle Speed RPM............................................................................................................	3,200–4,400 rpm
Operating RPM.............................................................................................................	6,900-7,200 rpm
Spark Plug Gap....................................................................................................	0.025 inch (0.635 mm)
Lubrication......................................................................................................................	Fuel/Oil Mixture
Fuel/Oil Ratio....................................................................................................................................	40:1
Fuel Tank Capacity............................................................................................................	20 oz. (591 ml)
Approximate Unit Weight (No fuel).............................................................................	17.8 lbs. (8.07 kg)

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

5